Command Manual SPP-R200. Mobile Printer Rev

Transcription

1 Command Manual SPP-R200 Mobile Printer Rev

2 1. Control Commands List COMMAND Name Funtion type 1 LF Print and line feed Print 2 FF Print and return to standard mode (in Print page mode) 3 CR Print and carriage return Print 4 ESC FF Print data in page mode Print 5 ESC J n Print and feed paper Print 6 ESC d n Print and feed n lines Print 7 CAN Cancel print data in page mode Character 8 ESC SP n Set right-side character spacing Character 9 ESC! n Select print mode(s) Character 10 ESC - n Turn underline mode on/off Character 11 ESC E n Turn emphasized mode on/off Character 12 ESC G n Turn double-strike mode on/off Character 13 ESC M n Select character font or Set card reader mode. Character/MSR 14 EOT Cancel card reader mode MSR 15 ESC R n Select an international character set Character 16 ESC t n Select character code table Character 17 ESC { Turn upside-down print mode on/off Character 18 GS! n Select character size Character 19 GS B n Turn white/black reverse print mode on/off Character 20 ESC 2 Select default line spacing Line Spacing 21 ESC 3 n Set line spacing Line Spacing 22 ESC c 5 n Enable/disable panel buttons Panel Button 23 HT Horizontal tab Print Position 24 ESC $ nl nh Set absolute print position Print Position 25 ESC T n Select print direction in page mode Print Position 26 ESC D n Set horizontal tab positions Print Position 27 ESC W n Set print area in page mode Print Position 28 ESC \ nl nh Set relative print position Print Position 29 ESC a n Select justification Print Position 30 GS $ n Set relative vertical print position in Print Position page mode 31 GS L nl nh Set left margin Print Position 32 GS W Set print area width Print Position 33 GS \ Set relative vertical print position in Print Position page mode 34 ESC * m nl mh Select bit-image mode Bit-image 35 DLE EOT n Transmit real-time status Status 36 GS r Transmit status Status 37 DLE ENQ Send real-time request to printer Mics 38 DLE DC4(Fn=2) Execute power-off sequence, Mics 39 DLE DC4(Fn=7) Transmit specified status in real-time Mics Rev

3 40 DLE DC4(Fn=8) Clear buffer(s) Mics 41 ESC = Select peripheral device Mics 42 Initialize printer Mics 43 ESC L Select page mode Mics 44 ESC S Select standard mode Mics 45 GS I Transmit printer ID Mics 46 GS : Start/end macro definition Macro 47 GS ^ Execute macro Macro 48 GS H Select print position of HRI characters Bar code 49 GS f Select font for HRI characters Bar code 50 GS h Set bar code height Bar code 51 GS k Print bar code Bar code 52 GS w Set bar code width Bar code 53 GS ( A Execute test print Mics 54 GS ( C Edit NV user memory CUSTOMIZE 55 GS ( D Enable/disable real-time command Mics 56 GS ( E Set user setup commands CUSTOMIZE 57 GS ( H Require response transmission Mics 58 GS ( L Set graphics data BIT-IMAGE 59 GS ( M Customize printer control value(s) CUSTOMIZE 60 GS ( K Select print control method(s) Mics 61 GS ( k Set up and print the symbol Two dimension 62 GS g 0 Initialize maintenance counter Mics 63 GS g 2 Transmit maintenance counter Mics 64 ESC v Transmit paper sensor status Status 65 FS & Select Kanji character mode 2bytes code 66 FS. Cancel Kanji character mode 2bytes code 67 GS v 0 Print raster bit image Bit-image Rev

4 2. Control Commands Details 2-1 Command Notation The name of the command. The code sequence.: ASCII Indicates the ASCII character equivalents. Hex indicates the hexadecimal equivalents. Decimal indicates the decimal equivalents. [ ] k indicates the contents of the [ ] should be repeated k times. Gives the allowable ranges for the arguments. Describes the function of the command. 2-2 Explanation of Terms LSB Least Significant Bit 2-3 Control Commands Details HT LF FF Horizontal tab. ASCII HT Hex 09 Decimal 9 Moves the print position to the next horizontal tab position. Print and line feed. ASCII LF Hex 0A Decimal 10 In standard mode, prints the data in the print buffer and feeds one line based on the current line spacing. In page mode, modes the print position in memory to feed one line based on the current line spacing. Print and return to standard mode in page mode. ASCII FF Hex 0C Decimal 12 In page mode, prints all the data in the print buffer collectively and switches from page mode to standardmode. Rev

5 CR [Notes] CAN DLE EOT n Print and carriage return. ASCII CR Hex 0D Decimal 13 This command is ignored CR. Cancel print data in page mode. ASCII CAN Hex 18 Decimal 24 In page mode, deletes all the print data in the current print area. Transmission real-time status. ASCII DLE EOT n Hex n Decimal 16 4 n 1 n 4 Transmits the status specified by n in real-time as follows: n Function 1 Transmit printer status. 2 Transmit off-line status. 3 Transmit error status. 4 Transmit paper roll sensor status. This printer transmits the following status in real time. n=1 : Printer status Bit Off/On Hex Decimal Function 0 Off 00 0 Fixed. 1 On 02 2 Fixed. 2 Off 00 0 Fixed. 3 Off 00 0 On-Line. On 08 8 Off-Line. 4 On Fixed. 5 Off 00 0 Not in on-line waiting status. On During on lines waiting status. 6 Off 00 0 Paper FEED button is turned Off. On Paper FEED button is turned On. 7 Off 00 0 Fixed. Rev

6 n=2 : Off-line status Bit Off/On Hex Decimal Function 0 Off 00 0 Fixed. 1 On 02 2 Fixed. 2 Off 00 0 Cover is closed. On 04 4 Cover is open. 3 Off 00 0 Paper is not being fed by using the paper FEED button. On 08 8 Paper is being fed by the paper FEED button. 4 On Fixed. 5 Off 00 0 No paper-end stop. On Printing is being stopped. 6 Off 00 0 No error. On Error has occurred. 7 Off 00 0 Fixed. Bit Off/On Hex Decimal Function 0 Off 00 0 Fixed. 1 On 02 2 Fixed. 2 Off 00 0 Fixed 3 Off 00 0 Fixed. 4 On Fixed. 5 Off 00 0 Fixed 6 Off 00 0 Fixed 7 Off 00 0 Fixed. n=3 : Error status n=4 : Continuous paper sensor status Bit Off/On Hex Decimal Function 0 Off 00 0 Fixed. 1 On 02 2 Fixed. 2 Off 00 0 Fixed. 3 Off 00 0 Fixed 4 On Fixed. 5 Off 00 0 Paper end sensor : paper present. On Paper end sensor : paper not present. 6 Off 00 0 Paper end sensor : paper present. On Paper end sensor : paper not present. 7 Off 00 0 Fixed. Rev

7 [Notes] If print data includes a character string with this command, the printer performs this command. User must consider this. - Do not embed this command within another command. - For example : Bit image data might include this command. - This command is ignored block data is transmitted. DLE ENQ n Real-time request to printer. ASCII DLE ENQ n Hex n Decimal 16 5 n 0 n 2 Responds to a request from the host computer. - n specifies the requests as follows : n Request 0 Works the same as when the paper FEED button is pressed once during waiting status during the operation of the GS ^ command. 1 Recovers from an error and restarts printing from the line where the error occurred. 2 Recovers from an error after clearing the receive and print buffers. [Notes] Specify n=1 or 2 after removing the cause of the error. If print data includes a character string with this command, the printer performs the command. User must consider this. - Do not embed this command within another command. - This command is ignored block data is transmitted. Rev

8 DLE DC4 fn a b (fn=2) Execute power-off sequence. ASCII DLE DC4 fn a b Hex fn a b Decimal fn a b fn=2 a=1 b=8 Executes the printer power-off sequence. - Stores the values of the maintenance counter. - Transmits the following power-off status (Header + Status + NUL). - Executes the printer power off. Power off status Hex Decimal Amount of data Header 3B H 59 1 byte Status 30 H 48 1 byte NUL 00 H 0 1 byte [Notes] If this command is encountered, the printer will not continue to process anything. To recover the printer to print again, it is necessary to turn the power on again or execute a hardware reset. If print data includes a character string with this command, the printer performs the command. User must consider this. - Do not embed this command within another command. - For example : Bit image data might include this command. - This command is ignored block data is transmitted. Rev

9 DLE DC4 fn m (fn=7) Transmits battery status.. ASCII DLE DC4 fn m Hex Decimal fn=7 m = 5 : This command is effective when the printer is disabled by ESC = (select peripheral device). m Function Related command Amount of data 5 Transmits battery status. None 1 byte [Notes] The transmitted battery status from this printer is constructed by [Header ~ NUL] as shown in the Transmitted data Hex Decimal Amount of data Header 37H 55 1byte Identifier 45H 69 1byte Battery remaining 30h-34H byte NUL 00H 0 1byte Battery remaining amount is as indicated in the following table. Battery remaining amount Hex 30H 31H 32H 33H 34H Decimal information 48 Battery remaining amount : H level 49 Battery remaining amount : M level 50 Battery remaining amount :L level 51 Battery remaining amount :S level 52 Battery isn't installed Rev

10 DLE DC4 fn d1...d7 (fn=8) Clear buffer(s). ASCII DLE DC4 fn d1...d7 Hex d1...d7 Decimal d1...d7 fn=8 d1=1, d2=3, d3=20, d4=1, d5=6, d6=2, d7=8 Clear all data stored in the receive buffer and the print buffer. Transmits the following three bytes data. SPP-R200 Hex Decimal Amount of data Header 37 H 55 1 byte Flag 25 H 37 1 byte NUL 00 H 0 1 byte [Notes] ESC FF Enters standard mode. The command must be inhibited for use in a system using this printer and the OPOS driver, java POS driver. If print data includes a character string with this command, the printer performs the command. User must consider this. - Do not embed this command within another command. - For example : Bit image data might include this command. - This command is ignored block data is transmitted. Print data in page mode. ASCII ESC FF Hex 1B 0C Decimal In page mode, prints all buffered data in the printing area collectively. Rev

11 ESC SP n ESC! n Set right-side character spacing. ASCII ESC SP n Hex 1B 20 n Decimal n 0 n 255 n=0 Sets the character spacing for the right side of the character to [n horizontal or vertical motion units]. The maximum right-side character spacing is : mm. Select print mode(s). ASCII ESC! n Hex 1B 21 n Decimal n 0 n 255 n=0 Selects print mode(s) using n as follows. Bit Off/On Hex Decimal Function 0 Off 00 0 Character font A (12 24) selected. On 01 1 Character font B (9 x 24) selected. 1,2 Off 00 0 Reserved. 3 Off 00 0 Emphasized mode not selected. On 08 8 Emphasized mode selected. 4 Off 00 0 Double-height mode not selected. On Double-height mode selected. 5 Off 00 0 Double-width mode not selected. On Double-width mode selected. 6 Off 00 0 Reserved. 7 Off 00 0 Underline mode not selected. On Underline mode selected. ESC $ nl nh Set absolute print position. ASCII ESC $ nl nh Hex 1B 24 nl nh Decimal nl nh 0 (nl + nh x 256) (0 nh 255, 0 nl 255) Sets the next print starting position, and the absolute print position, in reference to the left margin. The distance from the beginning of the line to the left margin is [(nl + nh x 256) x (vertical or horizontal motion units)]. Rev

12 ESC * m nl nh d1...dk Select bit image mode. ASCII ESC * m nl nh d1...dk Hex 1B 2A m nl nh d1...dk Decimal m nl nh d1...dk m=0, 1, 32, 33 1 (nl + nh x 256) 1023 (0 nl 255, 0 nh 3) 0 d 255 Specifies the bit image in m mode for the number of dots specified by nl and nh. * dpi : dots per 25.4mm {1 } m Mode 8-dot single-density 8-dot double-density 24-dot single-density 24-dot double-density Number of dots in vertical direction Vertical dot density Horizontal dot density Number of bytes (k) 8 60 dpi 90 dpi nl + nh x dpi 180 dpi nl + nh x dpi 90 dpi (nl + nh x 256) x dpi 180 dpi (nl + nh x 256) x 3 ESC n Turn underline mode on/off. ASCII ESC - n Hex 1B 2D n Decimal n 0 n 2, 48 n 50 n=0 Turn underline mode on or off, based on the following values of n : n Function 0,48 Turns off underline mode. 1,49 Turns on underline mode, set at 1-dot width. 2,50 Turns on underline mode, set at 2-dot width. Rev

13 ESC 2 ESC 3 n [Notes] ESC = n Select default line spacing. ASCII ESC 2 Hex 1B 32 Decimal The default line spacing is about 4.23 mm {1/6 inch}, which is equivalent to 30 dots. Set line spacing ASCII ESC 3 n Hex 1B 33 n Decimal n 0 n 255 The vertical or horizontal motion unit is approximately mm {1/203 inches}. This value equalsone dot pitch. Sets the current line spacing to [n x vertical motion units] inches. The maximum settable line spacing is mm. Select peripheral device. ASCII ESC = n Hex 1B 3D n Decimal n 0 n 3 Serial interface specification : - When turning on the printer : n=1 - When executing : Setting before executing n After processing Selects device to which host computer sends data, using n as follows : n Function 1 Specifies printer only. Rev

14 Initialize printer. ASCII Hex 1B 40 Decimal n 126 Clears the data in the print buffer and resets the printer mode to the mode that were in effect when the power was turned on. ESC D n1 nk NUL Set horizontal tab positions. ASCII ESC D n1...nk NUL Hex 1B 44 n1...nk 00 Decimal n1...nk 0 1 n k 32 n=8, 16, 24, 32, 40,..., 232, 240, 248 (for font A in a standard character size width) Sets horizontal tab positions. - n specifies the number of digits from the setting position to the left margin or the beginning of the line. - k specifies the number of bytes set for the horizontal tab position. ESC E n Turn emphasized mode on / off. ASCII ESC E n Hex 1B 45 n Decimal n 0 n 255 n=0 Turns emphasized mode on or off. - When the LSB of n is 0, emphasized mode is turned off. - When the LSB of n is 1, emphasized mode is turned on. Rev

15 ESC G n ESC J n ESC L ESC M n Turn double-strike mode on/off. ASCII ESC G n Hex 1B 47 n Decimal n 0 n 255 n=0 Turns double-strike mode on or off. - When the LSB of n is 0, double-strike mode is turned off. - When the LSB of n is 1, double-strike mode is turned on. Print and feed paper. ASCII ESC J n Hex 1B 4A n Decimal n 0 n 255 Prints the data in the print buffer and feeds the paper [n X vertical motion unit]. Select page mode. ASCII ESC L Hex 1B 4C Decimal Switches from standard mode to page mode. Select character font./ MSR card read ASCII ESC M n Hex 1B 4D n Decimal n n = 0, 1, 48, 49, 67, 68, 69, 70, 71, 72, 73 n=0 Selects only-byte character fonts Selects Card reader mode n Function 0, 48 Character font A (12 24) selected. 1, 49 Character font B (9 24) selected. 70 Set 1 track card reader mode 71 Set 2 track card reader mode 72 Set 1,2 track card reader mode 73 Transmits the setting value(s) of the memory switch 7 67 Set 2 track card reader mode 68 Set 3 track card reader mode 69 Set 2,3 track card reader mode Magnatic card read out put format Track 1 Rev

16 02H 41H 31H 31H 1CH DATA 76 characters 03H 0DH 0AH Track 2 02H 42H 31H 31H 1CH DATA 37 characters 03H 0DH 0AH Track 1,2 02H 43H 31H 31H 1CH 1CH DATA 76 characters 1CH DATA 37 Characters 03H 0DH 0AH Track 3 02H 44H 31H 31H 1CH DATA104characters 03H 0DH 0AH Track 2,3 02H 45H 31H 31H 1CH 1CH DATA 37 characters 1CH DATA104Characters 03H 0DH 0AH Transmits the setting value out put format Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 80H byte Data 30H ~ 37H 48 ~ 55 1 bytes NUL 00H 0 1 byte EOT Cancel card read mode ASCII EOT Hex 04 Decimal 4 [Notes]. Cancel card read mode Works the same as when the POWER button is pressed ESC R n Select an international character set. ASCII ESC R n Hex 1B 52 n Decimal n 0 n 13 n=0 Selects international character set in from the following table : n Character set n Character set 0 U.S.A 7 Spain I 1 France 9 Norway 2 Germany 10 Denmark II 3 U.K 11 Spain II 4 Denmark I 12 Latin America 5 Sweden 13 Korea 6 Italy Rev

17 ESC S ESC T n Select standard mode. ASCII ESC S Hex 1B 53 Decimal Switches from page mode to standard mode. Any data stored in the printer for printing in page mode is cleared. Select print direction in page mode. ASCII ESC T n Hex 1B 54 n Decimal n 0 n 3, 48 n 51 n=o Selects the print direction and starting position in page mode. n Print Direction Starting Position 0,48 Left right Upper left 1,49 Bottom to top Lower left 1,50 Right left Lower right 3,51 Top bottom Upper right ESC W xl xh yl yh dxl dxh dyl dyh Set relative print position. ASCII ESC W xl xh yl yh dxl dxh dyl dyh Hex 1B 57 xl xh yl yh dxl dxh dyl dyh Decimal xl xh yl yh dxl dxh dyl dyh 0 (xl + xh x 256) (0 xl 255, 0 xh 255) 0 (yl + yh x 256) (0 yl 255, 0 yh 255) 1 (dxl + dxh x 256) (0 dxl 255, 0 dxh 255) 1 (dyl + dyh x 256) (0 dyl 255, 0 dyh 255) Set the paper width of 58mm is selected : (xl + xh x 256) = 0 (xl=0, xh=0) (dyl + dyh x 256) = 840 (dyl=72, dyh=3) Set the position and the size of the printing area. - Horizontal starting position = [(xl + xh x 256) x (horizontal motion unites)]. - Vertical starting position = [(yl + yh x 256) x (vertical motion unites)]. - Horizontal printing area width = [(dxl + dxh x 256) x (horizontal motion unites)]. - Vertical printing area width = [(dyl + dyh x 256) x (vertical motion unites)]. Rev

18 ESC \ nl nh SPP-R200 Set relative print position. ASCII ESC \ nl nh Hex 1B 5C nl nh Decimal nl nh 0 (nl + nh x 256) (0 nl 255, 0 nh 255) Set the print starting position based on the current position to [(nl + nh 256) horizontal or vertical motion unit] - When (nl + nh 256) is positive number, the print starting position is specified to the right based on the current position. - When (nl + nh 256) is negative number, the print starting position is specified to the left based on the current position. ESC a n Select justification. ASCII ESC a n Hex 1B 61 n Decimal n 0 n 2, 48 n 50 n=0 In standard mode, aligns all the data in one line to the position specified by n as follows : n Justification 0, 48 Left justification 1, 49 Centering 2, 50 Right justification ESC c 5 n [Notes] ESC d n Enable / Disable panel button. ASCII ESC c 5 n Hex 1B n Decimal n 0 n 255 n=0 Enables or disables the panel buttons. - When the LSB of n is 0, the panel buttons are enabled. - When the LSB of n is 1, the panel buttons are disabled. When the printer cover is open, the panel buttons are always ignored regardless of the setting with this command. Print and feed n lines. ASCII ESC d n Hex 1B 64 n Decimal n 0 n 255 Prints the data in the print buffer and feeds n lines. Rev

19 ESC t n Select character code table. ASCII ESC t n Hex 1B 74 n Decimal n 0 n 5, 16 n 19, 21 n 24, 27 n 29, n=21, n=33, 36 n 37 n=255 For model without Thai character support : n=0 For model with Thai character support : n = 20 Selects a page n from the character code table. n Page 0 Page (USA, Standard Europe) 1 Page 1 Katakana 2 Page (Multilingual) 3 Page (Portuguese) 4 Page (Canadian-French) 5 Page (Nordic) 16 Page (Latin I) 17 Page (Cyrillic #2) 18 Page (Latin 2) 19 Page (Euro) 21 Page (Hebrew DOS code) 22 Page (Arabic) 23 Page 23 Thai42 24 Page (Greek) 27 Page 27 Farsi 28 Page (Cyrillic) 29 Page (Greek) 31 Page 31 Thai14 33 Page (Hebrew New code) 36 Page (Cyrillic) 37 Page (Turkish) ESC { n Turns upside-down printing mode on/off. ASCII ESC { n Hex 1B 7B n Decimal n 0 n 255 n=0 Turns upside-down printing mode on or off. - When the LSB of n is 0, upside-down printing mode is turned off. - When the LSB of n is 1, upside-down printing mode is turned on. Rev

20 GS! n Select character size. ASCII GS! n Hex 1D 21 n Decimal n 0 n 255 (where 1 Enlargement in vertical direction 8, 1 Enlargement in horizontal direction 8) n=0 Selects character size (enlargement in vertical and horizontal directions). Bit Function Setting Specifies the number of times enlarged in the vertical direction Specifies the number of times enlarged in the horizontal direction - Table 1 [Enlarged in horizontal direction] Hex Decimal Enlargement time (standard) times times times times times times times - Table 1 [Enlarged in vertical direction] Hex Decimal Enlargement time (standard) times times times times times times times Refer to Table 2 [Enlarged in vertical direction] Refer to Table 1 [Enlarged in horizontal direction] Rev

21 GS $ nl nh Set absolute vertical print position in page mode. ASCII GS $ nl nh Hex 1D 24 nl nh Decimal nl nh 0 (nl + nh x 256) (0 nl 255, 0 nh 255) Sets the absolute vertical print starting position to [(nl + nh 256) (vertical or horizontal motion units)]. GS ( A pl ph n m Execute test print. ASCII GS ( A pl ph n m Hex 1D pl ph n m Decimal pl ph n m (pl + ph x 256) = 2 (pl=2, ph=0) 0 n 2, 48 n 50 1 m 3, 49 m 51 Executes a test print with a specified test pattern on a specified paper type (roll paper). - n specifies the paper type as listed below to be tested : m Paper type 0, 48 1, 49 Paper roll 2, 50 - m specifies a test pattern as listed below : m Test pattern 1, 49 Hexadecimal dump 2, 50 Self Test Printing [Notes] 3, 51 Self Test rolling pattern If this command is processed while a macro is being defined, the printer cancels macro definition and starts processing this command. At that time, the macro becomes undefined. After processing this command, the printer performs a software reset. Rev

22 GS ( D pl ph m [a1 b1]...[ak bk] Enable/disable real-time command. ASCII GS ( D pl ph m [a1 b1]...[ak bk] Hex 1D pl ph m [a1 b1]...[ak bk] Decimal pl ph m [a1 b1]...[ak bk] 3 (pl + ph x 256) m=20 a=1, 2 b=0, 1, 48, 49 a Type(s) of real-time commands Default 2 DLE DC4 fn a b (fn=2) : Execute power-off sequence disable (b=0) Enable or disables the following real-time commands. a b Function 2 0, 48 DLE DC4 fn a b (fn=2) : Not processed (disabled) 1, 49 DLE DC4 fn a b (fn=2) : Processed (enabled) - pl, ph specifies (pl + ph x 256) as the number of bytes after ph (m and [a1 b1]...[ak bk]). - a specifies the type of real-time command. - b specifies enable or disable. If bit image data accidentally includes a character string with this command, it is recommended to use this command in advance to disable [Notes] the real-time command. Rev

23 GS ( E pl ph fn [parameter] Customize NV memory area. Customize the NV user memory area. The table below explains the functions available in this command. Executes commands related to the user setting mode by specifying the function code fn. fn Format No. Function 1 GS ( E pl ph fn d1 d2 1 Changes into the user setting mode. 2 GS ( E pl ph fn d1 d2 d3 2 Ends the user setting mode session. (Performs a soft reset.) 3 GS ( E pl ph fn [a1 b18...b11]... 3 Sets value(s) for the memory switch. [ak bk8...bk1] 4 GS ( E pl ph fn a 4 Transmits the settings of the memory switch to the host. 11 GS ( E pl ph fn a d1...dk 11 Sets the communication conditions for the serial interface. 12 GS ( E pl ph fn a 12 Transmits the communication conditions for the serial interface. [Notes] pl, ph specifies (pl + ph x 256) as the number of bytes after ph (fn and [parameter]). The user setting mode is a special mode to change the values in the NV user memory with this command. In Function 2, the printer performs software reset. Therefore, the printer clears the receive and print buffers, and resets all settings (user-defined characters, macros, and the character style) to the mode in effect at power on. Frequent write commands by this command, may damage the NV memory. Therefore, it is recommended to write to NV memory no more than 10 times a day. While processing this command, the printer is BUSY while writing data to the user NV memory and stops receiving data. Therefore it is prohibited to transmit data including the real-time commands during the execution of this command. Rev

24 <Function 1> GS ( E pl ph fn d1 d2 (fn=1) ASCII GS ( E pl ph fn d1 d2 Hex 1D pl ph fn d1 d2 Decimal pl ph fn d1 d2 (pl + ph x 256) = 3 (pl=3, ph=0) fn=1 d1=73, d2=78 Enter the user setting mode and notifies that the mode has changed. Hexadecimal Decimal Number of Data Header 37H 55 1 byte Flag 20H 32 1 byte NUL 00H 0 1 byte The following commands are enabled in the user setting mode. <Function 2> through <Function 12> of GS ( E, GS I. <Function 2> GS ( E pl ph fn d1 d2 d3 (fn=2) ASCII GS ( E pl ph fn d1 d2 d3 Hex 1D pl ph fn d1 d2 d3 Decimal pl ph fn d1 d2 d3 (pl + ph x 256) = 4 (pl=4, ph=0) fn=2 d1=79, d2=85, d3=84 Ends the user setting mode and performs a software reset. Therefore, the printer clears the receive and print buffers, and resets all settings (userdefined character, downloaded bit images, macros, and the print mode) to the mode that was in effect at power on. This function code (fn=2) is enabled only in the user setting mode. Rev

25 <Function 3> GS ( E pl ph fn [a1 b18...b11]...[ak bk8...bk1] (fn=3) SPP-R200 ASCII GS ( E pl ph fn [a1 b18...b11]... [ak bk8...bk1] Hex 1D pl ph fn [a1 b18...b11]... [ak bk8...bk1] Decimal pl ph fn [a1 b18...b11]... [ak bk8...bk1] 10 (pl + ph x 256) fn=3 a= 1,2,5,6,8 b=48, 49, 50 all switches are set to Off (b=48). Change the memory switch specified by a to the values specified by b. - When b=48, the applicable bit is turned to Off. - When b=49, the applicable bit is turned to On. - When b=50, the applicable bit is not changed. When a=1, the memory switch 1 is set as follows : Msw Set value function 1-1~3 48,48,48 print density 130% 48,48,49 print density 120% 48,49,48 print density 110% 48,49,49 print density 105% 49,48,48 print density 100% 49,48,49 print density 95% 49,49,48 print density 90% 49,49,49 print density 80% Reserved print speed 70mm/s 49 print speed 50mm/s 48 Offline Busy 49 printfer Buffer Full Busy Reserved Reserved When a=2, the memory switch 2 is set as follows : Msw Set value Function Reserved Reserved Reserved Rev

26 Code page Msw2-8 Msw2-7 Msw2-6 Msw2-5 Msw2-4 Character Table PC Katakana PC PC PC PC WPC PC PC PC Reserved PC Thai WPC Reserved Reserved Farsi WPC PC Reserved Thai Reserved WPC Reserved Reserved PC PC Reserved Reserved Reserved Reserved Reserved Rev

27 When a=5, the memory switch 5 is set as follows : Set power off time (1~90 minute.) No power off when memory switch value is 0 MSW5-8 MSW5-7 MSW5-6 MSW5-5 MSW5-4 MSW5-3 MSW5-2 MSW5-1 Value When a=6 the memory switch 6 is set as follows : Set Idle mode time When Bluetooth connection condition Minimum = 10 seconds Maxmum = 255 seconds No enter the saver mode when memory switch value is 0 MSW6-8 MSW6-7 MSW6-6 MSW6-5 MSW6-4 MSW6-3 MSW6-2 MSW Value When a=7 the memory switch 7 is set as follows : Msw Set value Function 7-1~3 48,48,48 Track 1/2 read mode command 48,48,49 Track 2/3 read mode command 48,49,48 Track 1 read mode AUTO trigger 48,49,49 Track 2 read mode AUTO trigger 49,48,48 Track 1/2 read mode AUTO trigger 49,48,49 Track 2 read mode AUTO trigger 49,49,48 Track 3 read mode AUTO trigger 49,49,49 Track 2/3 read mode AUTO trigger Rev

28 When a=8 the memory switch 8 is set as follows : Msw Setting Function Value Reserved X24 font 49 9X24 font No beeps for roll paper end 49 Beeps for roll paper end Reserved Reserved Reserved Reserved <Function 4> GS ( E pl ph fn a (fn=4) ASCII GS ( E pl ph fn a Hex 1D pl ph fn a Decimal pl ph fn a (pl + ph x 256) = 2 (pl=2, ph=0) fn=4 a=1, 2, 5, 6, 7, 8 Transmits the setting value(s) of the memory switch specified by a. Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 21H 33 1 byte Data 30H or 31H 48 or 49 8 bytes NUL 00H 0 1 byte Data for the setting is transmitted as 8 bytes or a data string in the order from bit 8 to bit 1, as follows : - Off : Hexadecimal = 30H / Decimal = 48 - On : Hexadecimal = 31H / Decimal = 49 Rev

29 ] <Function 11> GS ( E pl ph fn a d1.dk (fn=11) ASCII GS ( E pl ph fn a d1 dk Hex 1D pl ph 0B a d1 dk Decimal pl ph 11 a d1 dk 3<=(pL + ph x 256) <=8 (3<=pL<=8,0<= ph<=255) fn=11 1<=a 4 48<=d<=57 [a=1] 48<=d<=50 [a=2] d=48,49 [a=3] d=55,56 [a=4] 1<=k<=6 d1..dk= [a=1] d=48[a=2] d=48[a=3] d=56[a=4] sets the configuration item for the serial interface specified by a to the values specified by d1..dk a Configuration item 1 Transmission speed 2 Parity 3 Flow control 4 Data length Transmission speed(a=1) is specified by number. Example : When defining bps : 5bytes d1 dk (Hexadecimal = 31H,39H,32H,30H,30H /Decimal= 49,57,50,48,48) Parity (a=2) is specified by d as follows d Function 48 Select no parity 49 Select odd parity 50 Select even parity Flow control(a=3) is specified by d as follows d Fuction 48 Select Folow control DTR/DSR 49 Select Folow control XON/XOFFf Data Length(a=4) is specified by d as follows d Function 55 Selcect 7bit length 56 Selcect 8bit length Rev

30 <Function 12> GS ( E pl ph fn a (fn=12) ASCII GS ( E pl ph fn a Hex 1D pl ph fn a Decimal pl ph fn a (pl + ph x 256) = 2 (pl=2, ph=0) fn=12 1 a 4 Transmits the communication conditions of the serial interface pecified by a. a Communication Condition 1 Baud rate 2 Parity 3 Flow control 4 Data length Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 33H 39 1 byte Type of the 31H - 34H byte communication condition Separator 1FH 31 1 byte Setting value 30H - 39H bytes NUL 00H 0 1 byte Configuration of the setting value - When the baud rate (a=1) is specified : Baud rate (bps) d1 d2 d3 d4 d5 d When the parity setting (a=2) is specified : d1 Parity 48 No parity 49 Odd parity 50 Even parity - When the flow control setting (a=3) is specified : d1 Flow control 48 DTR / DSR (Fixed) 49 XON / XOFF - When the data length setting (a=4) is specified : d1 Data length 55 7 bits 56 8 bits If a is out of range, this command ignores the value which is specified with a. Rev

31 GS ( L pl ph m fn [parameter] Select graphics data. ASCII GS ( L pl ph m fn [parameter] Hex 1D 28 4C pl ph m fn [parameter] Decimal pl ph m fn [parameter] ASCII GS ( L p1 p2 p3 p4 m fn [parameter] Hex 1D 28 4C p1 p2 p3 p4 m fn [parameter] Decimal p1 p2 p3 p4 m fn [parameter] * In the description below GS ( L is used for the explanation. Processes graphics data according to the function code fn. fn Format Function No. Function 0, 48 GS ( L pl ph m fn Function 48 Transmits the NV graphics memory capacity. 2, 50 GS ( L pl ph m fn Function 50 Prints the graphics data in the print buffer. 3, 51 GS ( L pl ph m fn Function 51 Transmits the remaining capacity of the NV graphics memory. 64 GS ( L pl ph m fn d1 d2 Function 64 Transmits the defined NV graphics key code list. 65 GS ( L pl ph m fn d1 d2 d3 Function 65 Deletes all NV graphics data. 66 GS ( L pl ph m fn kc1 kc2 Function 66 Deletes the specified NV graphics data GS ( L pl ph m fn a kc1 kc2 b xl xh yl yh [c d1...dk]1...[c d1 dk]b GS ( L pl ph m fn kc1 kc2 x y GS ( L pl ph m fn a bx by c xl xh yl yh d1...dk Function 67 Function 69 Function 112 Defines the raster graphics data in the non-volatile memory. Prints the specified NV graphics data. Stores the raster graphics data in the print buffer memory. pl, ph specifies (pl + ph x 256) as the number of bytes after ph(m, fn, and [parameter]). Frequent write command executions by this command may damage the NV memory. Therefore, it is recommended to write to the NV memory no more than 10times a day. While processing this command, the printer is BUSY while writing data to the NV graphics memory and stops receiving data. Therefore it is prohibited to transmit data including the real-time commands during the execution of this command. Rev

32 <Function 48> GS ( L pl ph m fn (fn=0, 48) ASCII GS ( L pl ph fn m Hex 1D 28 4C pl ph fn m Decimal pl ph fn m (pl + ph x 256) = 2 (pl=2, ph=0) m=48 fn=0, 48 Transmits the total capacity of the NV bit-image memory (number of bytes in the memory area). Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 30H 48 1 byte Data 30H - 39H bytes NUL 00H 0 1 byte The total capacity data is converted to character codes corresponding to decimal data, then transmitted from the MSB. <Function 50> GS ( L pl ph m fn (fn=2, 50) ASCII GS ( L pl ph m fn Hex 1D 28 4C pl ph m fn Decimal pl ph m fn (pl + ph x 256) = 2 (pl=2, ph=0) m=48 fn=2, 50 Prints the buffer graphics which is stored by the process of Function 112. Feeds paper by the amount corresponding to the number of dots in the y direction of the buffered graphics. <Function 51> GS ( L pl ph m fn (fn=3, 51) ASCII GS ( L pl ph m fn Hex 1D 28 4C pl ph m fn Decimal pl ph m fn (pl + ph x 256) = 2 (pl=2, ph=0) m=48 fn=3, 51 Transmits the number of bytes of remaining memory (unused area) in the NV user memory. Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 31H 49 1 byte Data 30H 39H bytes NUL 00H 0 1 byte The number of bytes of remaining memory is converted to character codes corresponding to decimal data, then transmitted from the MSB. The data length is variable. Rev

33 <Function 64> GS ( L pl ph m fn d1 d2 (fn=64) ASCII GS ( L pl ph m fn d1 d2 Hex 1D 28 4C pl ph m fn d1 d2 Decimal pl ph m fn d1 d2 (pl + ph x 256) = 4 (pl=4, ph=0) m=48 fn=64 d1=75, d2=67 Transmits the defined NV graphics key code list. - When the key code is present : Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 72H byte Status 40H or 41H 64 or 65 1 byte Data 30H - 39H bytes NUL 00H 0 1 byte - When the key code is not present : Hexadecimal Decimal Amount of Data Header 37H 55 1 byte Flag 72H byte Status 40H 64 1 byte NUL 00H 0 1 byte If the number of the key code exceed 40, the key code is transmitted dividing up to The status if the continuous transmission data block is present is 41H. - The status if the continuous transmission data block is not present is 40H. After the [Header-NULL] is transmitted, the printer receives a response from the host; then it performs the process defined by the response. (See the tables below.) - When the status (existence of the next data block) is Hexadecimal = 41H / Decimal = 65 Response ASCII Decimal Process performed ACK 6 Transmits the next data. NAK 21 Transmits the previous data again. CAN 24 Ends the process. - When the status (for the last data block) is Hexadecimal = 40H / 40H/Decimal = 64 Response ASCII Decimal Process performed ACK 6 Ends the process. NAK 21 Transmits the previous data again. CAN 24 Cancels the process. Rev

34 <Function 65> GS ( L pl ph m fn d1 d2 d3 (fn=65) ASCII GS ( L pl ph m fn d1 d2 d3 Hex 1D 28 4C pl ph m fn d1 d2 d3 Decimal pl ph m fn d1 d2 d3 (pl + ph x 256) = 5 (pl=5, ph=0) m=48 fn=65 d1=67, d2=76, d3=82 Deletes all defined NV graphics data. <Function 66> GS ( L pl ph m fn kc1 kc2 (fn=66) ASCII GS ( L pl ph m fn kc1 kc2 Hex 1D 28 4C pl ph m fn kc1 kc2 Decimal pl ph m fn kc1 kc2 (pl + ph x 256) = 4 (pl=4, ph=0) m=48 fn=66 32 kc kc2 126 Deletes the NV graphics data defined by the key codes kc1 and kc2. Rev

35 <Function 67> GS ( L pl ph m fn a kc1 kc2 b xl xh yl yh [c d1...dk]1...[c d1...dk]b (fn=67) ASCII GS ( L pl ph m fn a kc1 kc2 b xl xh yl yh [c d1...dk]1...[c d1...dk]b Hex 1D 28 4C pl ph m fn a kc1 kc2 b xl xh yl yh [c d1...dk]1...[c d1...dk]b Decimal pl ph m fn a kc1 kc2 b xl xh yl yh [c d1...dk]1...[c d1...dk]b GS ( L parameter 3 (pl + ph x 256) (0 pl 255, 0 ph 255) Common parameter for GS ( L m=48 fn=67 a=48 32 kc kc2 126 b=1, 2 1 (xl + xh x 256) (yl + yh x 256) 2304 c=49 0 d 255 k = ( int ( ( xl + xh x 256 ) + 7 ) / 8 ) x ( yl + yh x 256 ) The total capacity of the NV graphic memory is only 256K bytes Defines the raster graphics data in the NV graphics area. - b specifies the number of the color of the defined data. - xl, xh specifies the defined data in the horizontal direction to (xl + xh x 256) dots. - xl, xh specifies the defined data in the vertical direction to (yl + yh x 256) dots. [Notes] - c specifies the color of the defined data. C Defined data color 49 Color 1 - Color 1 means black <Function 69> GS ( L pl ph m fn kc1 kc2 b x y (fn=69) ASCII GS ( L pl ph m fn kc1 kc2 x y Hex 1D 28 4C pl ph m fn kc1 kc2 x y Decimal pl ph m fn kc1 kc2 x y (pl + ph x 256) = 6 (pl=6, ph=0) m=48, fn=69 32 kc kc2 126 x=1, 2 y=1, 2 Prints the NV graphics data defined by the key codes kc1 and kc2. The graphics data is enlarged by x and y in the horizontal and vertical directions. Rev

36 <Function 112> GS ( L pl ph m fn a bx by c xl xh yl yh d1...dk (fn=112) ASCII GS ( L pl ph m fn a bx by c xl xh yl yh d1...dk Hex 1D 28 4C pl ph m fn a bx by c xl xh yl yh d1...dk Decimal pl ph m fn a bx by c xl xh yl yh d1...dk GS ( L parameter 11 (pl + ph x 256) (0 pl 255, 0 ph 255) Common parameter for GS ( L m=48, fn=112, a=48 bx=1, 2 by=1, 2 c=49 1 (yl + yh x 256) 1662 (when by = 1) [Notes] k = ( int ( ( xl + xh x 256 ) + 7 ) / 8 ) x ( yl + yh x 256 ) Stores the raster graphics data, enlarged by bx and by in the horizontal and vertical directions to the print buffer. - xl, xh specifies the raster graphics data in the horizontal direction as (xl + xh x 256) dots. - xl, xh specifies the raster graphics data in the vertical direction to (yl + yh x 256) dots. - c specifies the color of the defined data. c Printing color 49 Color 1 - Color 1 means black In standard mode, each color can be defined only once. Rev

37 GS ( M pl ph fn m Customize printer. Protects or recovers values or data set or defined in the active area by commands. Fn Function No. Descriptions 1, 49 Copies the settings stored in the active area to Function 1 the storage area (save settings). 2, 50 Copies the settings stored in the storage area Function 2 3, 51 Function 3 to the storage area (load settings). Enables or disables automatic loading of the settings upon initialization. - Active area : Volatile memory (RAM) - Storage area : Hon-volatile memory (Flash ROM) List of commands Setting value Command Status ESC c 3, GS a Defined data GS : Kind of character ESC M, ESC R, ESC t style ESC!, ESC -, ESC E, ESC G, ESC V, ESC {, GS!, GS B, GS b, etc ESC SP, ESC 2, ESC 3 Bar code GS H, GS f, GS h, GS w 2-dimension code <Function 065> through <Function 070> of GS ( k Print position ESC D, ESC T, ESC a, GS L, GS W etc ESC c 4, ESC c 5, GS ( D, GS P <Function 1> GS ( M pl ph fn m (fn=1, 49) [Notes] ASCII GS ( M pl ph fn m Hex 1D 28 4D pl ph fn m Decimal pl ph fn m (pl + ph x 256) = 2 (pl=2, ph=0) fn=1, 49 m=1, 49 Copies the setting stored in the active area to the mth storage area. Frequent write command executions by this command may damage the NV memory. Therefore, it is recommended to write to the NV memory no more than 10 times a day. While processing this command, the printer is BUSY while writing data to the NV user memory and stops receiving data. Therefore it is prohibited to transmit data including the real-time commands during the execution of this command. Rev

38 <Function 2> GS ( M pl ph fn m (fn=2, 50) ASCII GS ( M pl ph fn m Hex 1D 28 4D pl ph fn m Decimal pl ph fn m (pl + ph x 256) = 2 (pl=2, ph=0) fn=2, 50 m=0, 1, 48, 49 When (m=0,48), initializes all settings in the active area, as described in these specifications. When (m=1,49), copies the setting stored in the mth storage area to the active area. If no data in the storage area is protected, all settings in the active area are initialized as described in these specifications. <Function 3> GS ( M pl ph fn m (fn=3, 51) ASCII GS ( M pl ph fn m Hex 1D 28 4D pl ph fn m Decimal pl ph fn m (pl + ph x 256) = 2 (pl=2, ph=0) fn=3, 51 m=0, 1, 48, 49 When m=0,48, does not load data in the storage area to the active area upon initialization. When m=1,49, loads data in the storage area to the active area upon initialization. Rev

39 GS ( k pl ph cn fn [parameter] Specify and print the symbol. Processes the data concerning two-dimensional code. (PDF417) - Symbol type is specified by cn. - Function is specified by fn. cn Type of Symbol 48 PDF417 (2-dimensional code) [Notes] cn fn Function Function 065 PDF417 : Specify the number of columns 66 Function 066 PDF417 : Specify the number of rows 67 Function 067 PDF417 : Specify the width of module 68 Function 068 PDF417 : Specify the module height 69 Function 069 PDF417 : Specify the error correction level 70 Function 070 PDF417 : Specify the option 80 Function 080 PDF417 : Store the received data in the symbol save area 81 Function 081 PDF417 : Print the symbol data in the symbol save area 82 Function 082 PDF417 : Send the size information of the symbol data in the symbol save area For PDF417 symbol data (when cn=48) The symbol data specified by Function 080 d1...dk is stored in the printer and is printed by the specification of Function 081. The symbol data in the save area is reserved until the following processing is performed : - Function 080 or 180 is executed - is executed - The printer is reset or the power is turned off When processing Function 081 or 082, the setting values of Functions 065 to 070 are used. If the printable area is not large enough, the symbol may not be printed. Executing Function 081 after executing Function 080 repeatedly prints the same symbol data. By using Functions 065 to 070 combined with Function 081, the same symbol data d1...dk is printed differently. By using Function 082, the symbol size printed by Function 081 is available. Rev

40 <Function 065> GS ( k pl ph cn fn n (fn=65) [Notes] ASCII GS ( k pl ph cn fn n Hex 1D 28 6B n Decimal n (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=65 0 n 30 n=0 Specifies the number of columns of the data area of PDF n=0 specifies auto processing - When n is not 0, specifies the number of columns of the data area as n code word. Settings of this function affect the processing of Functions 081 and 082. When auto processing (n=0) is specified, the maximum number of columns in the data area is 30 columns. The following data is not included in the number of columns : - Start pattern and stop pattern - Indicator code word of left and right When auto processing (n=0) is specified, the number of columns is calculated by the printing area when processing Functions 081, 082, module width (Function 067), and option setting (Function 070). Setting of this function are effective until is executed, the printer is reset, or the power is turned off. Rev

41 <Function 066> GS ( k pl ph cn fn n (fn=66) [Notes] ASCII GS ( k pl ph cn fn n Hex 1D 28 6B n Decimal n (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=66 n=0, 3 n 90 n=0 Specifies the number of rows of the data area of PDF n=0 specifies auto processing - When n is not 0, specifies the number of rows of the symbol as n rows. Settings of this function affect the processing of Functions 081 and 082. When auto processing (n=0) is specified, the maximum number of rows is 90. When auto processing (n=0) is specified, the number of rows is calculated by the printing area when processing Functions 081, 082, module height (Function 068). Setting of this function are effective until is executed, the printer is reset, or the power is turned off. <Function 067> GS ( k pl ph cn fn n (fn=67) [Notes] ASCII GS ( k pl ph cn fn n Hex 1D 28 6B n Decimal n (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=67 1 n 4 n=3 Specifies the width of a module of PDF417 symbol. Settings of this function affect the processing of Functions 081 and 082. The setting unit differs, depending on the printer models. Setting of this function are effective until is executed, the printer is reset, or the power is turned off. <Function 068> GS ( k pl ph cn fn n (fn=68) [Notes] ASCII GS ( k pl ph cn fn n Hex 1D 28 6B n Decimal n (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=68 2 n 8 n=3 Specifies the module height of PDF417 symbol. - Specify the height to [a module width x n]. Settings of this function affect the processing of Functions 081 and 082. Setting of this function are effective until is executed, the printer is reset, or the power is turned off. Rev

42 <Function 069> GS ( k pl ph cn fn m n (fn=69) [Notes] ASCII GS ( k pl ph Cn fn m n Hex 1D 28 6B m n Decimal m n (pl + ph x 256) = 4 (pl=4, ph=0) cn=48 fn=69 m=48 48 n 8 [m=48] n=1 Specifies the error correction level of PDF417. m Function 48 The error correction level is specified by level Settings of this function affect the processing of Functions 081 and 082. Error correction level is specified by level. Error correction level specified by level (m=48) is as follows. The number of the error correction code word is fixed regardless of the number of code words in the data area. m Function Number of error correction code word 48 Error correction level Error correction level Error correction level Error correction level Error correction level Error correction level Error correction level Error correction level Error correction level <Function 070> GS ( k pl ph cn fn m (fn=70) [Notes] ASCII GS ( k pl ph cn fn m Hex 1D 28 6B m Decimal m (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=70 m=0,1 m=0 Set or cancels the option of PDF417. m Function 0 Cancels the processing of simplified PDF417 symbol. 1 Sets the processing of simplified PDF417 symbol. - m=0 cancels the processing of simplified PDF417 symbol. - m=1 sets the processing of simplified PDF417 symbol. Settings of this function affect the processing of Functions 081 and 082. When simplified PDF417 symbol is canceled, standard PDF417 symbol is automatically selected. Setting of this function are effective until is executed, the printer is reset, or the power is turned off. Rev

43 <Function 080> GS ( k pl ph cn fn m d1...dk (fn=80) [Notes] ASCII GS ( k pl ph cn fn m d1...dk Hex 1D 28 6B pl ph d1...dk Decimal pl ph d1...dk 4 (pl + ph x 256) (0 pl 255, 0 ph 255) cn=48 fn=80 m=48 0 d 255 k = (pl + ph x 256) - 3 Stores the PDF417 symbol data (d1...dk) in the symbol save area. Data stored in the symbol save area by this function are processed by Function 081 and 082. The data in the symbol save area are reserved after processing Function 081 or 082. k bytes of d1...dk are processed as symbol data. Specify only the data code word of the symbol with this function. Be sure not to included the following data in the data d1...dk because they are added automatically by the printer. - Start pattern and stop pattern. - Indicator code word of left and right. - The descriptor of symbol length. (the first code word in the data area) - The error correction code word calculated by modulus 929. Setting of this function are effective until the following processing is performed : - Function 080 or 180 is executed. - is executed. - The printer is reset or the power is turned off. <Function 081> GS ( k pl ph cn fn m (fn=81) [Notes] ASCII GS ( k pl ph cn fn m Hex 1D 28 6B m Decimal m (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=81 m=48 Encodes and prints the PDF417 symbol data in the symbol save area. In standard mode, use this function when printer is at the beginning of a line, or there is no data in the printer buffer. A symbol that size exceeds the printing area cannot be printed. If there is any error described below in the data of the symbol save area, it cannot be printed. - There is no data (Function 080 is not processed). - If [(number of columns x number of rows) < number of code word] when auto processing is specified for number of columns and number of rows. - Number of code word exceeds 928 in the data area. Rev

44 The following data are added automatically by the encode processing. - Start pattern and stop pattern. - Indicator code word of left and right. - The descriptor of symbol length. (the first code word in the data area) - The error correction code word calculated by modulus Pad codeword. The data area includes the following code words. - Data specified by Function The descriptor of symbol length. (the first code word in the data area) - The error correction code word calculated by modulus Pad codeword. When auto processing (Function 065) is specified, the number of columns is calculated by the current printing area, module width (Function 067), option setting (Function 070), and the code word in the data area. Maximum number of the columns in 30. When auto processing (Function 066) is specified in page mode, the number of rows is calculated by the current printing area, module height (Function 068), and the code word in the data area. The maximum number of rows is 90. Printing of symbol is not affected by print mode (emphasized, doublestrike, underline, white/black reverse printing, or 90 clockwise-rotated), except for character size and upside-down printing mode. In standard mode, this command executes paper feeding for the amount needed for printing the symbol, regardless of the paper feed amount set by the paper feed setting command. The printing position returns to the left side of the printable area after printing the symbol, and printer is in the status beginning of the line, or there is no data in the print buffer. In page mode, the printer stores the symbol data in the print buffer without executing actual printing. The printer moves printing position to the next dot of the last data of the symbol. The quiet zone is not included in the printing data. Be sure to include the quiet zone when using this function. <Function 082> GS ( k pl ph cn fn m (fn=82) ASCII GS ( k pl ph cn fn m Hex 1D 28 6B m Decimal m (pl + ph x 256) = 3 (pl=3, ph=0) cn=48 fn=82 m=48 Encodes and sends size information of the PDF417 symbol data in the symbol save area. In standard mode, use this function when printer is at the beginning of a line, or there is no data in the printer buffer. Rev