TELI CS8560D Reference Information

Transcription

1 TELI CS8560D Reference Information Reference Information on cameras supported by MultiCam compliant frame grabbers Public Information Copyright Euresys s.a Author: Pascal PIRSON

2

3 MultiCam Cameras Reference Information TELI CS8560D 1.1 TELI CS8560D Essential characteristics Common characteristics Manufacturer Model Configuration Imager Imager technology Imager size Imager array Pixel pitch Scanning method Pixel frequency Line rate TELI CS8560D P60SA, P60RA, P60SM, P60RM Area-scan, Monochrome CCD interline transfer 4.88 mm (H) x 3.66 mm (V), 1/3 inch 644(H) x 494 (V) 7.4 µm (H) x 7.4 µm (V), square pixels Progressive scan MHz khz See "Configuration Dependent Characteristics" Frame rate 60 fps Rate achieved in synchronous mode Tap structure SINGLE_A (Single analog tap output) Synchronization mode ANALOG (PLL) or MASTER (HV drive) According to selected configuration Asynchronous reset Asynchronous shutter Mode settings Connection system Power requirements Mechanical Available Available Dip-switches HR12M (Video, Power, Control) 12 V DC, ± 10%, 1.5 W 29 mm (H) x 29 mm (W) x 39.5 mm (D) Weight: 42 g C-mount lens According to selected configuration Copyright Euresys s.a Page 3

4 TELI CS8560D MultiCam Cameras Reference Information Configuration dependent characteristics Configuration P60SA P60RA P60SM P60RM Tap structure Single-A Single-A Single-A Single-A Scanning method Progressive scan Progressive scan Progressive scan Progressive scan Frame rate 60 frames per seconds Up to 60 frames per seconds 60 frames per seconds Up to 60 frames per seconds Operation mode SYNC mode CTL mode SYNC mode CTL mode Asynchronous reset Synchronizatio n mode Feature Single-A CTL mode SYNC mode ANALOG mode MASTER mode Not available Available Not available Available ANALOG mode ANALOG mode MASTER mode MASTERmode Legend: Meaning Single analog tap output Asynchronous reset with exposure time adjusted through frame grabber settings Highest speed sustained scanning without asynchronous reset Phase locking on composite synchronization with low jitter Camera timing is imposed by the grabber through synchronization drive signals Recommended equipment MultiCam compliant boards Model Configuration Board CS8560D P60SA P60RA P60SM P60RM Domino Harmony, Domino Melody, Domino Gamma, Domino Alpha, Domino IOTA Domino Harmony, Domino Melody, Domino Gamma, Domino Alpha, Domino IOTA, Domino Delta Interconnection cables Model Configuration Cable name Designator Usage CS8560D P60SA P60RA P60SM P60RM Single Channel RGC A15-C11-XX Asynchronous reset Single HD15M connector Copyright Euresys s.a Page 4

5 MultiCam Cameras Reference Information TELI CS8560D Locating items Camera rear view Control switches Gain control HR12M Connector HD/VD switch Copyright Euresys s.a Page 5

6 TELI CS8560D MultiCam Cameras Reference Information Connection information HD15F pin-out Valid for all configurations WEN out Power Return (GND) Power Supply (+12V) TRIGGER in Video return (GND) VIDEO out Metal Shell (SGND) Signal Ground (GND) VD in HD in Signal Ground (GND) 2 pins HR12M connector Camera outside view Signal mapping Cable "Single Channel R" Pin Pin name Configuration Board P60SA P60RA P60SM P60RM Usage VIDEO out V1+ VIDEO return V1- Analog channel GND Power Supply +12V +12V Power Power supply Return GND PGND Horizontal HD in HIO Not synchronization Not used used Not Vertical VD in VIO used synchronization TRIGGER in RST Not used Not Asynchronous used reset Signal Return GND GND Signal return Metal Shell SGND EMC shield WEN OUT Gate Not used Not used Not used Gate pulse Refer to the camera cable A15-C11-xx for additional useful manufacturing information. Copyright Euresys s.a Page 6

7 MultiCam Cameras Reference Information TELI CS8560D Camera setup DIP switch HD/VD switch Valid for configurations P80SA Look Setting Effect HD/VD HIGH 75 75Ω HD and VD signals are terminated at 75 ohms Valid for configurations P60SA and P60SM Look Switch Setting Effect OFF ON 1 ON/OFF Gain: as required by the application ON/OFF Electronic shutter switch: See "Establishing 3 ON/OFF exposure time" 4 ON/OFF 5 OFF 1/60s non-interlace 6 OFF Normal Shutter mode 7 OFF 8 OFF Scan: All pixel 9 OFF 10 OFF FIX mode Valid for configurations P60RA Look Switch Setting Effect OFF ON ON/OFF Gain: as required by the application 2 ON 3 OFF Exposure controlled by reset pulse width 4 OFF 5 OFF 1/60s non-interlace 6 OFF Random trigger SYNC reset Internal sync 7 OFF 8 OFF Scan: All pixel 9 OFF 10 ON PULSE W mode Copyright Euresys s.a Page 7

8 TELI CS8560D MultiCam Cameras Reference Information Valid for configurations P60RM Look Switch Setting Effect OFF ON 1 ON/OFF Gain: as required by the application 1 2 ON 2 3 OFF Exposure controlled by reset pulse width 3 4 OFF OFF 1/60s non-interlace 6 6 OFF Random trigger V reset Internal sync 7 7 ON 8 8 OFF 9 Scan: All pixel 10 9 OFF 10 ON PULSE W mode Establishing exposure time for P60SA, P60SM Switch 2 Switch 3 Switch 4 Exposure OFF OFF OFF Shutter is OFF ON OFF OFF Exposure time is 1/200s OFF ON OFF Exposure time is 1/500s ON ON OFF Exposure time is 1/1000 s OFF OFF ON Exposure time is 1/2000 s ON OFF ON Exposure time is 1/4000 s OFF ON ON Exposure time is 1/8000 s ON ON ON Exposure time is 1/20000 s Copyright Euresys s.a Page 8

9 MultiCam Cameras Reference Information TELI CS8560D Board Setup Domino Harmony, Melody and Delta. Valid for all configurations On Domino Harmony, there is no hardware setup Domino Iota, Alpha and Gamma Valid for all configurations On Domino Gamma boards, jumper blocks should be configured as indicated by the following MultiCam parameters: Jumper Parameter Value Meaning JumperCK Pin 9 and pin 10 of the channel connector are used as a third video lane ZLANE borrowed to the Z connector JumperL1 The video lane 1 is sensed as a differential 75 Ω terminated analog signal DT applied at pin 1 (V1+) and pin 2 (V1-) JumperL2 The video lane 2 is sensed as a differential 75 Ω terminated analog signal DT applied at pin 11 (V2+) and pin 12 (V2-) JumperH The pin 14 (HIO) and pin 15 (GATE) of the connector feeding the channel can TTL be used as input or output in TTL format JumperV The pin 4 (VIO) and pin 5 (EXP) of the connector feeding the channel can be TTL used as input or output in TTL format This corresponds to the following jumper blocks settings: V H CK TG JumperV = TTL VIO, EXP control: TTL I/O JumperH = TTL HIO, GATE control: TTL I/O JumperCK = EMPTY Camera clock: None JumperL1 = DT JumperL2 = DT Lane 1, 2: Differential Terminated This drawing applies to the jumper block facing the connector the camera is linked to. Copyright Euresys s.a Page 9

10 TELI CS8560D MultiCam Cameras Reference Information Channel Configuration Scripting method To setup MultiCam according to the required configuration, you have to use the CamFile (Scripting method). Please refer to the following tables and MultiCam documentation. If you have selected the configuration: P60SA You have to set the following MultiCam parameter to the given value: CamFile CS8560D_P60SA.cam P60RA CS8560D_P60RA.cam P60SM CS8560D_P60RM.cam P60RM CS8560D_P60RM.cam Copyright Euresys s.a Page 10

11

12 Copyright Euresys s.a Last edition