waterproof coin operated binoculars

Transcription

1 DigiFox DFC waterproof coin operated binoculars Instruction Manual DigiLens Co., Ltd. 5F NO.207 SEC 2, CHUNG CHING N.ROAD. TAIPEI, TAIWAN R.O.C. TEL : (886-2) FAX: (886-2)

2 Contents Safety precautions....3 Operation precautions.. 4 Nomenclature....5 Assembly and installation.6-9 Specifications Operation inspection Note...13 This manual is intended for persons responsible for the installation and safety of coin operated binoculars 2

3 Safety precautions Take steps to ensure that your customers do not look directly at the sun through these sightseeing binoculars looking directly at the sun through these binoculars may seriously damage the eyes managers in charge of the binoculars must ensure that customers use the binoculars correctly post a warning similar to the following beside the binoculars so that it can be easily seen by all customers Never look at the sun directly. Doing so may seriously damage the eyes. 3

4 Operation precautions Caution! 1.Lens cleaning lens surfaces may be dusted with a soft lens brush use a soft cotton cloth or lens cleaning tissue moistened with lens cleaning liquid to wipe away stains or smudges in a circular motion from the center to the periphery. Do not use velvet cloth, ordinary tissue or wipe the lens roughly, as any of these may scratch the lens surface 2.Daily care after use and protection against rain and snow 3.Other cautions sightseeing binoculars may be subject to rough handling or vandalism. To prevent malfunctions and keep binoculars properly maintained, be sure to observe the daily preventive measures indicated in this instruction manual before installing sightseeing binoculars at a location where they will be exposed to rain or water, consult DigiLens Co.,Ltd or your local distributor 4

5 Nomenclature 1.Binoculars body 2.Eyepiece 3.Objective lens 4.Coin slot 5.Coin eject button 6.Coin outlet 7.Upper cover 8.Invisible lock 9. Key Stand 11.Stand base 12.Coin box 13.Coin box cover 14. Screw M8 15.Hexagonal a wrench 16.Screw bolt/nut 17.Screw M

6 Assembly and installation The Assembly Steps of the Coin Operated Binoculars C/No. 1 C/No. 1 C/No. 1 C/No. 1 C/No. 2 Figure (1) Figure (2) Figure (3) Figure (4) Figure (5) Screw (M6) (6pcs) Screw (1/2 bolt/nut) (4pcs) The Hexagonal Wrench The Body of the Binoculars (with Coin Box) The Pillar with the Base 6

7 Assembly and installation Assembly Step 1: Diagram of Parts Positions. Assembly Step 2: Please assemble the figure 4 with the figure 5, then put 6 screws as figure 1 to the fixed positions where re inside the coin box of the figure 4. Assembly Step 3: Please use this hexagonal wrench to tighten the 6 screws. 7

8 8 Assembly and installation

9 Assembly and installation 9

10 Specifications Model Magnification Objective dia Field of view Exit pupil Relative Brightness Interpupillary distance Twilight factor Waterproof Focus range Height at eyepiece Azimuth Tilting angle Coin capacity Shutter duration Power source Battery life Color 20X80 25X80 30X80 20X 25X 30X 80mm 3 degree 2.6 degree 2 degree 4.0mm 3.2mm 2.67mm mm Weatherproof 45 M~infinity 45 M~infinity 45 M~infinity 140cm 360 degree +30 degree, - 45 degree 3600 coins 1~3 min 1.5Vx2 (3AAAx2) 3-4 Months Ivory 10

11 Operation inspection 1.To check binocular tilt and panning while supporting the binoculars with the hands, check that they tilt up/down and pan smoothly. panning angle should cover a full 360º(endless). 2.To check shutter operation insert a coin in the coin slot and check that shutters open and close. inserting the coin activates the timer switch to keep the shutter open for one minute. (unless specially requested, shutter opening time is set to one minute when delivered.) the shutter opening Time is adjustable within a range of one to three Minutes. repeat the above a few times. If operations are satisfactory, close the upper cover and secure with screws using the hexagonal wrench. once inserted, the coin is not returned. If impropriety coins are erroneously inserted, they will be automatically ejected from the coin outlet. 3If 3.If shutter does not open when a coin is Inserted the coin path may be blocked by paper, dust or other objects; if this happens, push the coin eject button. If the coin does not return even after pushing the button, open the upper cover using the hexagonal wrench and clean inside the Box. 11

12 Operation inspection 4. If the shutters do not open even after a coin is inserted, or if shutters remain open: there may be insufficient battery power or Internal mechanical malfunction. First, check battery voltage using a tester. if the battery voltage is extremely low, replace with a fresh battery. If shutters still do not operate even after battery replacement, the trouble is caused by malfunction of electric circuits or other mechanical parts. Please consult Digilens Co., Ltd. 5.Installing battery open the upper cover using the hexagonal wrench. remove the battery holder plate from the battery case by turning the screws counterclockwise. Remove the old battery, then mount the new battery taking care to correctly position the terminals. Incorrect installation may cause malfunction. Finally, reattach the battery holder plate back by turning the screws clockwise. Operating instructions (Optional) The following instructions are show on the right side of the upper cover. 12

13 Note Specifications and design are subject to change without notice. No reproduction in any form of this manual, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from DigiLens Co.,Ltd. DigiLens Co., Ltd. 5F NO.207 SEC 2, CHUNG CHING N.ROAD. TAIPEI, TAIWAN R.O.C. TEL : (886) FAX : (886)