Assist Vision Slider. AV-300 Instruction Manual. TIMES Corporation

Transcription

1 Assist Vision Slider AV-300 Instruction Manual TIMES Corporation

2 Before Use / Contents Before Use Thank you for purchasing the Assist Vision Slider. Carefully read this Instruction Manual before use to ensure safe operation. Please keep this manual in a convenient place for quick reference. For the handling of other units (not supplied) to be used together with this main unit, refer to the instruction manual of each unit. Contents Before Use...2 Contents...2 Important Safeguards...3 Handling Precautions Outline of Equipment Configuration of Equipment Part Names and Functions Connection/Operation Methods Various Operations Troubleshooting Warranty and Repair Service Disposal/Recycling of Packing Materials/Units Specifications

3 Important Safeguards Read Instructions All the safety and operating instructions should be read before the appliance is operated. Retain Instructions The safety and operating instructions should be retained for future reference. Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to. Follow Instructions All operating and use instructions should be followed. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Water and Moisture Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 3

4 Important Safeguards Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. Grounding or Polarization This product may be equipped with either a polarized 2-wire AC line plug (a plug having one blade wider than the other) or a 3-wire grounding type plug (a plug having a third grounding pin). The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Power-Cord Protection Powersupply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 4

5 Important Safeguards Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance this indicates a need for service. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 5

6 Important Safeguards SA 1965 SA 1966 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures; Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio TV technician for help. USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part 15 of the FCC rules. If there should be a leak of liquid from the Assist Vision Slider, do not touch the liquid as it may cause loss of sight or skin trouble. If the liquid enters the eye or contacts the skin, immediately wash the contaminated eye or skin with a sufficient quantity of clean water, such as tap water, and consult your doctor. 6

7 Handling Precautions Assist Vision Slider complies with the NTSC (National Television System Committee) television broadcast system adopted by Japan, the U.S. and Canada. This product should not be connected to any video/tv unit of different broadcasting system. Do not store this product in any place directly exposed to sunlight or near any heating device. Negligence could lead to discoloration, deformation or failure. Do not place this product in an area that is exposed to humidity, dust, sea wind or vibration. Environmental conditions for operation are as shown below. Temperature: 5 to 40 (41 to 104 ) Humidity : 30 to 80% or lower (no condensation) Use only a soft, dry cloth for cleaning. Do not use any volatile substances including benzine, thinner or detergent. If Assist Vision Slider is charged when the power switch is ON, more time is required to fully charge. The Assist Vision Slider may become warm when being charged. Charge the Assist Vision Slider in a cool place not exposed to direct sunlight or heating device. Changing may cut-off before being fully charged if placed in an area of high temperature. 7

8 Handling Precautions Assist Vision Slider has rollers for moving around. Use Assist Vision Slider on a sufficiently wide, level surface. Using this product on a tilted surface or narrow area could lead to the unit tipping over. Built-in batteries are consumables, and are not covered by warranty. Repetition of short charging (about 30 min.) and operation could result in reduction of battery life (Memory Effect). To prevent this from occurring, discharge the battery fully by leaving the power ON (without connecting the AC adaptor) until the battery power light goes off. This should be done approx. once a month. Black or colored specks may appear on the LCD screen (defective pixels). This is not a result of faulty equipment and unless more than 10 such specks appear, this will not be covered under the warranty. A transparent protective sheet is supplied with the LCD monitor. Please remove the protective sheet before use. 8

9 1.Outline of Equipment Assist Vision Slider is a color video magnifier assembled with TV camera, lens and LCD monitor. Images taken by the camera unit are enlarged and displayed on the LCD monitor. The Camera unit and camera holder are detachable from the main unit. By connecting the camera to the main unit, Assist Vision Slider can be used for reading and viewing (horizontally or vertically) and for writing. Rollers for moving around are positioned underneath the unit. The unit moves right and left or forwards and backwards in its vertical position. The camera unit can also detach from the main unit for harder to access surfaces. A writing implement can also fit underneath the camera unit/camera holder in between the two White Pins for writing. The in-built battery allows continued use without an external power source. The unit can also be used even while the battery is being charged (power receptacle is required for battery charging). 9

10 2.Configuration of Equipment First check the contents. If any of the following items are not included, or become lost, please consult your dealer. Main unit Camera unit Camera holder AC adaptor Power cable Video cable Instruction Manual Warranty 10

11 3.Part Names and Functions Main unit Indicator Power switch Turn ON or OFF the power of Assist Vision Slider. When power is turned ON, the light on the camera unit is displayed, and the LCD monitor displays images. While Assist Vision Slider is operated by battery, the LED (indicating the battery power) goes ON. 11 Main unit (front)

12 Part Names and Functions Battery power LED When the power switch is turned ON, the LED illuminates Red or Green, according to the remaining battery power. The LED lights up green, unless the battery power is running short, in which case the LED will light up red. The LED does not go ON when the built-in battery is being charged or when the AC adaptor plug is connected to the battery charge input terminal (power being supplied). Charge LED This LED lights up red when the built-in battery is being charged, and goes OFF when the battery charge completes. Brake knob To prevent non-intentional movement, apply the brake when pausing or stopping the unit and release the brake when using the unit. Video output terminal This unit may also be connected to another TV monitor by using the supplied video cable. 12

13 Part Names and Functions Charge input terminal For battery charging, connect the supplied AC adaptor to this terminal. Once connected, the battery charge will start automatically, and automatically shut off when the battery is fully charged. If the power switch is turned ON during battery charge, the unit starts operation while continuing the battery charge. The battery can not be recharged when already fully charged. Mode/Contrast knob By pressing this knob, it is possible to set the display mode of the LCD monitor screen to "Color", "Black and White" or "Reversed Black and White". If the power is turned ON, the first mode is Color. When pressed once, Black and White is selected. When pressed again, Reversed Black and White is selected. If pressed further, the Color mode is resumed, and so on. By turning this knob to the left or right in the Black and White mode or Reversed Black and White mode, it is possible to adjust the screen contrast. Even if the knob is turned in the Color mode, the screen will not change. Please note that this operation also applies to the video signal connected to the video input terminal. 13

14 Part Names and Functions LCD monitor The LCD monitor displays the image taken by the camera unit and the image of the input video signal. The indicator is a mark to align the monitor with the camera unit. The LCD monitor can be tilted fowards or to the right or left, for the most comfortable viewing angle. Caution Take care not to push the LCD monitor screen with strong force, or hit it with a hard object. 14

15 Part Names and Functions Main unit Main unit (Rear side) Camera input terminal (VIDEO1) Camera connection. Do not connect this to any unit or device other than the camera unit. Video input terminal (VIDEO2) Connect, as required, to an external video signal such as a hand held video camera. Camera select switch By setting this switch to the camera input terminal side, images taken by the camera unit are displayed on the LCD monitor. To display the images from the device connected to the video input terminal, set the switch to the video input terminal side. 15

16 Part Names and Functions Camera unit and camera holder Guide pin Camera unit This unit takes pictures of the object. This unit slides into the camera holder at a specific angle. Ensure both White Pins touch the photographing surface for the image to be in focus. Focus is fixed and no adjustments are necessary. The White Pins must also make contact with the photographing surface when using the camera unit without the camera holder. The Guide Pin and Position Indicator shows the correct way to hold/insert the camera unit in relation to the LCD monitor. For writing, insert the writing implement into the writing area of the camera unit (in between the two White Pins). 16

17 Part Names and Functions Position Indicator Writing area Zoom ring By turning this ring, to the left or right, it is possible to change the magnification of the image. Adjust magnification while checking the LCD monitor. Camera holder This is used to combine the main unit and camera unit. The main unit is provided with 3 places to mount the camera holder. The mounting place can be changed for right-handed or left-handed use. 17

18 4.Connection/Operation Methods Prior to connection, make sure that the power of the main unit is turned OFF (power switch is set to O side). First, apply the brake. Move the brake knob to the right, and push the main unit slightly and make sure that the unit does not move (brake is applied). Caution The brake of the main unit is effective merely to help stop the main unit on a slightly tilted surface. Take proper care not to use this on a tilted desk or narrow place, and to apply the brake in every pause or stop of operation. 18

19 Connection/Operation Methods Connect the cable from the camera unit to the camera input terminal of the main unit. Make sure that the camera select switch is set to the camera input terminal side. For right handed, horizontal viewing, install the camera holder to the mounting hole in the right side of main unit, and insert the camera unit into the camera holder. Ensure that both the camera unit and LCD monitor s position indicators are pointing in the same up direction. 19

20 Connection/Operation Methods Connect the power cable to the supplied AC adaptor, and connect to the power receptacle. Connect the cable plug of the AC adaptor to the battery charge input terminal. The indicator LED will light up. To charge without using the main unit, leave as it is until the charging is completed. Reference charging time is about 2 hours (depends on the remaining battery power, operating environment and operated hours). 20

21 Connection/Operation Methods Memo The following description assumes that the cables have already been connected, the battery is fully charged and the unit is now being operated by the battery. Please note that the unit can be used even during battery charge, however, the indicator LED, etc. may differ from the description below. Release the brake by moving the brake knob to the left. Push the main unit softly, and make sure that the main unit moves smoothly. When power switch is turned ON (set to I side), the Battery Power and camera unit LED will light up, and the image will be displayed on the LCD monitor. 21

22 Connection/Operation Methods Turn the zoom ring of the camera unit to the left or right to adjust the image size. Select and adjust the contrast in the Black and White and Reversed Black and White modes. 22

23 Connection/Operation Methods Adjust the screen by tilting the LCD monitor forwards or to the right or left for most comfortable viewing. To display the images taken by the camera unit on an external TV monitor, connect the video output terminal to the video input terminal of the external TV monitor with the supplied video cable. 23

24 Connection/Operation Methods To display images from an external video source such as a hand held video camera, set the camera select switch to the video input terminal side, and connect the video signal from the external camera to the video input terminal. When the battery runs short, the Battery Power LED lights up red. If it is necessary to use the unit continuously, you will need to charge the battery. Stop operation only after turning OFF the power switch (set to side). Request When turning ON the power, make sure that the cable from the camera unit is connected. When connecting/disconnecting cables, be sure to apply the brake, and make sure that the power of the unit is OFF. Please ensure the cable is properly connected and disconnected and handle cables at the plug ends. 24

25 5.Various Operations Assist Vision Slider can be used in a vertical or horizontal position and for both left and righthanders. Writing Insert the writing implement in the writing area (in between the two White Pins) of the camera unit, and begin writing. The LCD monitor captures the image. The Pins rotate, and can be adjusted for easy writing. 25

26 Various Operations For right-handed, horizontal position Set the unit with its front directed to yourself, and install the camera holder to the mounting hole in the right side. Insert the camera unit with the position indicator in the same direction as the LCD monitor. Guide the unit left and right. Position indicator Position indicator The direction of movement 26

27 Various Operations For left handed, horizontal position Set the unit with its front directed to yourself, and install the camera holder to the mounting hole in the left side. Insert the camera unit with the position indicator in the same direction as the LCD monitor. Guide the unit left and right. The direction of movement 27

28 Various Operations For Right-handed, vertical position Set the unit in a vertical position with its right side directed to yourself (position indicator pointed to the right), and install the camera holder to the mounting hole in the back (right side at this moment). Insert the camera unit with the position indicator in the same direction as the LCD monitor. Guide the whole unit forwards or backwards. The direction of movement 28

29 Various Operations For left-handed, vertical position Set the unit in a vertical position with its left side directed to yourself (position indicator pointed to the left), and install the camera holder to the mounting hole in the back (left side at this moment). Insert the camera unit with the position indicator in the same direction as the LCD monitor. Guide the whole unit forwards or backwards. The direction of movement 29

30 Various Operations Using the camera unit detached from main unit Remove the camera unit from the camera holder, and hold it in your hand. With the position indicator pointing in the same direction as the LCD monitor. Guide the camera along the area to be magnified, ensuring the two White Pins of the camera touches the surface. The image will be displayed on the LCD monitor. The detached camera unit may be used to read from a medicine bottle or box, food package, or a thick book. After the expiration of the warranty period, first of all, consult your dealer. When it is determined that the product can resume the normal condition after repair, we will repair the product as a charged service at your request. 30

31 6.Troubleshooting Image is not displayed. Cause Cable is not connected correctly. Power is not supplied. Camera select switch is not selected correctly. Battery is not charged. Corrective action Connect the cable correctly. Turn ON the power switch. Select the camera select switch correctly. Charge the battery. Contrast cannot be adjusted. Cause Black and White or Reversed Black and White mode is not selected. Corrective action Select the Black and White or Reverse Black and White mode. Battery is depleted in a short period of time. Cause Corrective action Battery's memory effect Refresh the battery occurs. (charge fully). End of battery service Send a request to life replace the battery. Check the above things. If any abnormality is found, consult your dealer. 31

32 7.Warranty and Repair Service The warranty card is contained in the package of the Assist Vision Slider. Be sure that the warranty card carries the serial number, the date of delivery, etc., and keep it in a safe place. The period of warranty is indicated on the warranty card. Note that the warranty does not apply to the builtin battery which is expendable. To replace the battery, consult your dealer. Note that warranty does not apply to 10 defective pixels or fewer. When you want us to repair the Assist Vision Slider during the warranty period, read this instruction manual again, particularly the "Handling Precautions" section. If the trouble still remains, be sure to turn OFF the power switch of the unit, and then contact your dealer. For any question about our after-sale services, ask your dealer. When you contact your dealer, be sure to give them your name and address, the name and model of the product, the date of purchase and details of the problem. When you want us to repair the Assist Vision 32

33 Warranty and Repair Service Slider after the expiration of the warranty period, first of all, consult your dealer. Once it is determined that the product can be repaired, we will repair the product as a charged service at your request. 8.Disposal/Recycling of Packing Materials/Units Assist Vision Slider has a built-in battery. Please consult your dealer if you are wanting to recycle the in-built battery. Do not dismantle the unit yourself. You are also requested to recycle the packing materials. 33

34 9.Specifications Power voltage :DC16 V (using supplied AC adaptor) Current consumption :Max Approx. 1.3 A Applicable power source :AC90 to 132 V 50/60 Hz Power consumption : Max. 25 W Outside dimensions (excluding protrusions) (Camera unit) :Dia x L5.51 (Power unit) :W6.93, H6.89, D6.3 Weight :Approx. 4.2lbs (incl.battery) TV system :Conformable to NTSC system Photographing element :Color CMOS image sensor No. of pixels :Approx. 250,000 pixels White balance :Auto Gain control :Auto Electronic shutter :1/100 sec. Mode :Color/Black and White /Reversed Black and White Contrast adjustment :Black and White /Reversed Black and White mode. Output signal :VBS1.0 V (p-p) 75 Ohm non-equilibrium, 1 system Input signal :VBS1.0 V (p-p) 75 Ohm non-equilibrium, 1 system 34

35 Specifications Photographing area Zoom ratio Focus Display unit Display size Lighting Battery Battery charge time Battery continuous operating time Accessories AC adaptor Power cable Video cable Instruction manual Warranty card :Max horizontally, 0.45 vertically Min horizontally, 0.23 vertically (For LCD monitor) :Approx. twice :Fixed (at tip of camera unit) :Color TFT LCD monitor :6.4 inches :Built-in (white LED) :Built-in (nickel metal-hydride storage battery) :Approx. 2 hours (when not operated) :Approx. 2 hours :1 unit :1 pc :1 pc :2 copies :1 copy The specifications are subject to change without notice. 35

36 Times Corporation , Takatsukasa Takarazuka-City, Hyogo JAPAN Tel: Fax: URL: The contents of this Instruction Manual are subject to change without notice. 6X1KDG002 Printed in Japan 36