1.Please read through the user manual in its entirety. Please follow the rules in this manual to ensure your safety.

Transcription

1

2 Table of contents 1. Introduction 2. Package Contents 3. Diagram 4. Operating Instructions 4.1 General Operations 4.2 Pairing Q9 to mobile phone 5. Charging Q9 6. Technical Specifications 7. Notice 8. Warranty & Return Policy

3 1.Introduction Thank you for choosing Q9 v3.0. Quikcell Q9 v3.0 Bluetooth Headset allows you to make or receive handsfree calls. Please read this user manual carefully before using the headset. You might also need to read the manual of your phone, which provides important information of operation and safety. Before using Q9 v3.0: 1.Please read through the user manual in its entirety. Please follow the rules in this manual to ensure your safety. 2.Be cautious of any edges, uneven surfaces, metal parts, accessories and packaging so as to prevent any possible injury or damage. 3.Do not modify, repair or dismantle this Headset. Doing so may result in fires, electric shocks, complete failure of this Headset, etc. (All of which, are not covered under warranty) 4.Do not use any diluents or volatile liquid to clean the Headset. 5.Do not use the Headset in a hazardous location.

4 2.Package Contents This package contains the following Bluetooth Headset Q9 v3.0 AC Charger USB Charger Two Removable Clear Ear hooks User Manual

5

6 4.Operating Instructions 4.1General Operations: Turn on the headset Language Selection Turn off the headset Entering pairing mode Press and hold MFB (Multi-function Button) for 4 seconds, when LED start blinking. You can hear a voice prompt power is on At the first time of use, you have the option to select a language for voice prompts after the device is powered on. To reset language, press and hold MFB and Vol+ at same time until power off. When the headset is powered on next time, language selection is available again. When headset is on, press and hold MFB for 4 seconds, when LED flashes twice in red. You can hear a voice prompt power is off at the same time. If your Q9 headset has not been paired to any mobile phones, it enters pairing mode when the power is on. If the headset has been paired to some phone before and you need to pair it with a new phone, press and hold MFB for 6 seconds until the LED flashes in red and blue alternatively. You will hear a voice prompt ready to pair, and the following prompts will guide you to sync the headset with your phone.

7 Entering pairing mode Answer a call Reject a call End a call Increase volume Decrease volume Voice dial Last number redial After paired,the voice prompt phone one/two connected. Press MFB to answer an incoming call. Voice prompt: Incoming call - phone one/two. Press and hold MFB for 2 seconds and you will hear a 'beep'.voice prompt: call terminated - phone one/two. Press MFB to terminate the current call. Voice prompt: call terminated - phone one/two. Tap Vol+.When reaching the maximum volume, voice prompt: volume highset. Tap Vol-.When reaching the minmum volume, voice prompt: volume lowest. Tap MFB when Q9 is connected to the phone and in standby mode. Press and hold MFB for two seconds, it will dial the last number in your phone call history. 4.2 Pairing Q9 v3.0 to mobile phones To use your Bluetooth headset Q9 v3.0, you must first pair it to the mobile phone. Pairing is a one-time process. Once your headset is paired to your mobile phone, they will remain paired and automatically recognize each other whenever they are within a certain range.

8 If the connection between the phone and headset is lost, tap the Multi-function Button (MFB) on the headset to reconnect. If headset has not been paired to your phone before, follow the Voice prompt from the device or the steps below: Turn on your phone and ensure its Bluetooth function is activated. If there is no previous paired phone within 33 ft range, Q9 will enter pairing mode automatically after power on. The LED flashes in blue and red alternatively. If Q9 is previously paired to another phone in range, press and hold MFB for about 6 seconds from OFF mode until the LED indicator light flashes in blue and red alternatively. Search Bluetooth devices on your phone by following the phone's instructions. Refer to your phone's user manual for more information. After a few seconds the phone will list Qnine 3.0 as a discovered device. Select it and follow your phone instructions to pair to it. Your phone may request a passkey or PIN#, input If your phone has Simple Pairing feature, you will not be asked for it. Your phone will confirm the pairing. It may also ask if you want to connect to Q Select Yes/OK. You may now use your Q9 v3.0 headset properly. Q9 v3.0 headset supports multi-connectivity. To pair the 2nd phone, turn off Q9 v3.0 and then press and hold MFB to enter pairing mode. Follow the instructions above to pair the headset with the phone until you hear "Phone 2 is connected". Then go to the Bluetooth menu of Phone 1 and connect to "Q9 3.0". You will here "Phone 1 is connected". 5.Charging Q9 v3.0 If the voice prompt says battery is low,you need to charge your Q9 v3.0 headset. Q9 v3.0 headset is easy to connect to a wall outlet or a USB charger through a computer. Make sure that your Q9 v3.0 Bluetooth headset is fully charged for at least 4 hours before initial use. Insert one end of your charger to a wall outlet (AC Charger) or the USB port of your PC and the

9 other end to the charging jack on side of Q9 (USB Charger). While being charged, the LED indicator of your headset remains red. When the charging is complete, the LED becomes blue. You must only use the charger that is included. You must recharge the Headset if it has not been used for more than 12 months. 6.Technical specifications Bluetooth v3.0 Supported profiles: HFP v1.5, HSP v1.1 Range: up to 33 ft. Talk time: up to 5 hours. Standby time: up to 140 hours. Dimensions (L W):33 14mm Weight: 6 g. Multi-language voice prompts: English, Chinese and Spanish

10 7.Notice FCC Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. European CE Notice The Bluetooth Headset is in conformity with the following essential requirement of Council Directive 1999/5/EC (refer to the R&TTE Directive): Articles 3.1a, 3.1b and 3.2. The product is manufactured in accordance with the Annex 2 of the above directive. Declaration of Conformity (DOC) The Bluetooth Headset is compliant with and adopts the Bluetooth specification 3.0 and has successfully passed all the interoperability tests that are specified in the Bluetooth specification. However, interoperability between the device and other Bluetooth enable products is not guaranteed. 8.Warranty & Return Policy

11 Alpha Comm Enterprises, Inc. warrants this product as free of defects in material, design and workmanship for the period of one year from the original date of purchase. The warranty is limited to the original purchaser. If during the period of warranty this product proves defective under normal use and service you should return the product to the retailer from whom it was purchased or to an authorized repair center. The liability of Alpha Comm Enterprises, Inc. and its appointed repair company is limited to the cost of repair and/or replacement of the product under warranty. Products sent for warranty service must be accompanied by a copy of the original purchase receipt, the original box, materials and accessories. All cost associated with the return of the product under warranty are the responsibility of the original purchaser. A $6.95 Shipping and Handling Fee will apply in order for Alpha Comm Enterprises, Inc. To ship out a new/refurbished product to customer. Alpha Comm Enterprises, Inc. will not assume any responsibility for any loss or damage incurred in shipping. For more information, visit Authorized Warranty Center Alpha Comm Enterprises, Inc Lakes Parkway, Suite B Lawrenceville, Georgia Phone

12