XSLAN+4400 XSLAN+2xxx XSLAN+1xxx XSLAN+140

Transcription

1 The SHDSL XSLAN+ switch enables two distant Ethernet networks to be connected using one to four telephone grade twisted pairs. Over one twisted pair (0,9 mm diameter), the data rate reaches 5.7 up to 3.7 Km or up to 15 on a shorter distance. A full range of products is offered : The XSLAN+140 is a plug & play model configured with a few DIP switches. The XSLAN+4400 is a four SHDSL interfaces line concentrator. The XSLAN+ 2XXX is a two shdsl interfaces product to multiply the data rate or for daisy chain networks. All that range of products - except the XSLAN+140 provide VLANs, SNMP, QoS and, optionally, two built-in serial gateways. XSLAN+4400 XSLAN+ range is made for demanding applications; they feature extend end T range, low consumption, total galvanic isolation (except models including RS232 or RS485 interfaces), double power supply input. XSLAN+2xxx XSLAN+1xxx XSLAN+140 Utilities, water, energy, Transport, building automation... Vidéo, VoIP... 5,7 over 3,7 Km (1 pair diam. 0,9 mm) 22,8 over 3,7 Km (4 pairs diam. 0,9 mm) 1 simple «plug & play» product 4 SHDSL lines concentrator VLAN & SNMP Quality of Service DiffServ 2 or 4 Ethernet 10/100 BT ports 2 serial ports (option) IPV4 & IPV6 T : -20 C / +70 C

2 Only 8 DIP swiches are required to set-up the XSLAN+140. If necessary, a simple diagnostic html server is available to check the data rate and the connection quality. XSLAN+2400 is used to settle a link up to 30M/s (2 copper pairs) or 60Mp/s (4 copper pairs). Transmission is not cut when one copper pair is cut. 1twisted pair 4 tiwisted pairs With backup XSLAN+2400 comes with 2 SHDSH ports and can be used to build a «daisy chain topology» via a tswited copper pair The XSLAN+4400 features four SHDSL interfaces; it is the right solution to connect up to four remote Ethernet networks through copper pairs Network 1 Network 2 XSLAN+ can be equipped with the «Bypass» feature. The electro-mechanical relay between both SHDSL line is automatically closed to connect the 2 lines when for any reason the XSLAN is switched off. Network 3 Network 4 XSLAN+ handles the RSTP protocol (Rapid Spanning Tree). The failure detection and recovery is made in only few seconds.

3 When the SHDSL network forms a daisy chain and when it is not possible to form a secured ring, the loop VPN function allows a network redundancy if a public connection (Internet) or private (MPLS) is available at each end of the SHDSL network. The data rate reaches 5.7 over 3.7 Km (wire diam. 0.9 mm). But it reaches 15 if the distance is shorter than 0.7 Km (wire diam. 0.9 mm). The bandwidth can be divided in four priority classes. The services (protocol + port number) which have to be transmitted can be distributed between that classes according to their priority level. It is possible for instance to reserve a narrow bandwidth with a high priority level to industrial protocols or to VoIP and a large one with lower priority to video transmission. Each port including the Ethernet 10/100 ports, the SHDSL ports and also the serial gateways and the Html server) can be assigned to a particular VLAN. Optionally, two built-in serial gateways can be provided. Data can be encapsulated either into TCP or UDP (towards one or several destinations).

4 General characteristics IP functions Dimensions 136 x 47 x 142 mm (h, l, p) IP V4 & IPV6 Installation 35 mm DIN rail SNMP SNMP V2 RFC1213 MIB II Protection IP20 HDSL2-SHDSL-LINE-MIB CEM Safety. Banned Substances ESD : EN : 6 KV contact discharge RF field : EN : 10V/m < 2 GHz Fast transient : EN Surge V. : EN : 4KV line / earth EN UL1950, T -20 C /+ 70 C 2002/95/CE ROHS european union directive QoS IP routing HOST-RESOURCES-MIB IF-MIB IP-MIB BRIDGE-MIB 4 priority levels DiffServ compliant Static routes RIP V1 et V2 Broadcast filtering 5 to 95 % non condensing Connector Supply voltage Consumption Security Isolation Supply voltage 2 positions screw terminal block XSLAN+1400, 2400, 4400: 10 à 60 VDC XSLAN+1230, 2230, 4230: 10 à 60 VDC XSLAN+1220, 2220, 4220: 10 à 30 VDC XSLAN+1XXX 200 ma sous 24 VDC XSLAN+2XXX 270 ma sous 24 VDC XSLAN+4XXX 375 ma sous 24 VDC Double supply voltage input (Except xslan+140) Reverse polarity protection Total galvanic isolation (Except models with RS232 or RS485) Digital input / output Output 1 isolated output 0,5 A / 24 VDC max Operating alarm Input Logical 0 < 1VDC - Logical 1 > 3 VDC Serial gateway (Option) Serial ports 2 serial links RS232 or RS485 RS232 connector RJ45 RS485 connector 2 positions srew block Data rate 1200 up to b/s Parity N/O/E 7 or 8 bits, 1 or 2 Stop Serial Gateway Raw TCP client & server UDP unicast or towards broadcast list Multicast Telnet Modbus master & slave Uni-Telway slave

5 Ethernet 10/100 BT Ethernet SHDSL VLAN Ethernet auto MDI / MDIX 2 or 4 RJ ah : 2BaseTL IEEE 802.1Q compliant Serial gateway & html server in a VLAN Destination filtering Distance versus data rate through one pair Indicative values Débit ,7 5,7 2,3 1,15 192Kb/s Câble Ø 0.9mm 0,7Km 1Km 1,5Km 2,5Km 3,7Km 6Km 8Km 13Km Câble Ø 0.4mm 0,4Km 0,6Km 0,9Km 1,3Km 2Km 3Km 4Km 7Km

6 XSLAN Number of SHDSL ports Data rate on one pair diam. 0,9 mm 3,7 km - Data rate on one pair diam. 0,9 mm 0,7 km - Agregated speed - diam. 0,9 mm 3,7 km - Agregated speed - diam. 0,9 mm 0,7 km - 5,7 5,7 5,7 5,7 5,7 5,7 5,7 5, ,4 11,4 11,4 22, Concentrator 2 or 4 SHDSL ports SHDSL backup Number of Ethernet ports 10 / 100BT Number of serial port RS RS Power Input Backup Galvanic isolation «plug & play» configuration with DIP switch Configuration via HTML server Diagnostic via HTML server Administration SNMP IP router, Quality of service DiffServ (QoS) VLAN By-Pass (BP) RSTP protocol Auto négociation master/slave Fabriqué en France par ETIC TELECOM