Product Guide.

Transcription

1 Product Guide Extended transmission via Copper cable (Coax, UTP, 2-Wire) - Long distance transmission for network signal and - Repeaer Rev.3.1

2 Contents Introduction... 1 Product Guide... 3 & over Coax... 4 Premium Single Port over Coax Transceiver ECP-2704T... 5 Premium 4 Port over Coax Transmitter ECP-2704R... 6 Premium 4 Port over Coax Receiver ECP-2601T/R... 7 Premium Single Port over Coax Transmitter / Receiver ECP-2808RM/2816RM... 8 Premium 8/16 Port over Coax Managed Receiving Switch (NMS) ECP-9501T/R...10 Single Port over Coax Transmitter / Receiver (Elevator) ECP-9504R Port over Coax Receiver ECP-9508R/9516R / 16 Port over Coax Receiver ECP-8401T/R...13 Single Port over Coax Transmitter / Receiver ECP-8301EP/NP...14 Single Port over Coax Transmitter / Receiver ECP-101T/R...15 Single Port over Coax Transmitter / Receiver (Multicast) & over UTP EUP 2601T/R...16 Premium Single Port over UTP Transmitter / Receiver & over 2-Wire ETP-2601T/R...21 Premium Single Port over 2-Wire Transmitter / Receiver ETP-101T/R...22 Single Port over 2-Wire Transmitter / Receiver (Multicast) Hybrid Switch HPS Port Hybrid Switch (NMS) HPS-1008RM Port Hybrid Switch (NMS) EPR Gigabit & + Repeater EPR-101/ & Repeater Others PF VDC/1.2A Supply BTE-02/03/ Single Port BNC to RJ-45 / RJ-11 / Terminal Block Exchanger ERM Port 19 /2U Rack Mount Bracket (for ECP/EUP 101R) Applications 30 EUP 2808RM/2816RM...17 Premium 8/16 Port over UTP Managed Receiving Switch (NMS) EUP 8401T/R...19 Single Port over UTP Transmitter / Receiver EUP 101T/R...20 Single Port over UTP Transmitter / Receiver (Multicast)

3 Introduction About Intercoax Co.,Ltd. Since 2014, INTERCOAX CO., LTD. is a leading developer and manufacturer of value-added over Coax & Any Cable extenders and repeaters. With successful launch of the single port EoC ( over coax) extender, Intercoax product range has expanded to meet the needs of the explosive IP surveillance market based on the migration from analogue to IP system. From single port over coax solution to Multiport EoC managed switch, Intercoax has continued developing customer oriented products and management software for enterprise grade features and capabilities. As one of leading developers of high quality, cost eective EoC equipment, Intercoax will continue providing various solutions and cutting-edge technologies for customer s satisfaction. 1

4 Introduction Complete range of over Coax/ Any Cable extenders & repeaters From single port EoC converter to multiport managed EoC switch, Intercoax oers complete range of over Coax / Any Cable solution, designed to meet a variety of needs. Cost & Time saving solution Re-using the existing cables such as Coaxial, UTP or 2 -wire cables. Easy & Fast installation Analog cameras can be replaced with IP camera easy and fast way compared with pulling a new network cable. Extended cable distance over Coax / Any Cable Solution provides long distance data & power transmission over 100 meters distance limitation of network devices. over existing cable (Coax, UTP, 2-Wire) Without pulling power cable, Intercoax devices provide power transmission feature up to over diversity of the cable. Multi-Connection 1:N, N:1, Daisy Chain, Star, etc. Various application Using exclusive adapters, Intercoax devices allow to use not only coaxial cable but also, /6e, Cat.3, communication cable and power cable for long distance data and power transmission. No business interruption for renovation Easy & fast installation without pulling new cable, destroying wall for cabling work, etc. Minimal impact on customer operations. Data Encryption 128-bit AES encryption for secured data communication. 2 Network Solution Provider

5 Product Guide Model Product category Port Max. Bandwidth (Mbps) Max. Data Distance (m/rg-6) Max. Distance (m/rg-6) Max. Output (Watt) Premium Single Port EoC Transceiver 1 10/100/ ECP-2704T Premium 4 Port EoC Transmitter 4 10/100/ (sharing power) ECP-2704R Premium 4 Port EoC Receiver 4 10/100/ ECP-2601T Premium Single Port EoC Transmitter 1 10/ *(270) ECP-2601R Premium Single Port EoC Receiver 1 10/ *(270) (IEEE802.3at input) ECP-2808RM Premium 8 Port EoC Managed Receiving Switch 8 10/100/ & over Coax & over UTP & over 2-Wire (1Pair) Hybrid Switch Repeater ECP-2816RM Premium 16 Port EoC Managed Receiving Switch 16 10/100/ ECP-9501T Single Port EoC Transmitter 1 10/ ECP-9501R Single Port EoC Receiver 1 10/ ECP-9504R 4 Port EoC Receiver 4 10/ ECP-9508R 8 Port EoC Unmanaged Receiver 8 10/100/ ECP-9516R 16 Port EoC Unmanaged Receiver 16 10/100/ ECP-8401T Single Port EoC Transmitter 1 10/ ECP-8401R Single Port EoC Receiver 1 10/ (IEEE802.3at input) ECP-8301EP Single Port EoC Transceiver 1 10/ ECP-8301NP Single Port EoC Transceiver 1 10/ ECP-101T Single Port EoC Transmitter [Multicast Ready] 1 10/ ECP-101R Single Port EoC Receiver [Multicast Ready] 1 10/ (IEEE802.3at input) EUP-2601T Premium Single Port over UTP Transmitter 1 10/100 EUP-2601R Premium Single Port over UTP Receiver 1 10/ *(270) 95 *(270) 1200() 1200() () 1200() (IEEE802.3at input) EUP-2808RM 8 Port UTP Managed Receiving Switch 8 10/100/ () 1200() - EUP-2816RM 16 Port UTP Managed Receiving Switch 16 10/100/ () 1200() - EUP-8401T Single Port over UTP Transmitter 1 10/ () 1200() 60 EUP-8401R Single Port over UTP Receiver 1 10/ () 1200() (IEEE802.3at input) EUP-101T Single Port over UTP Transmitter [Multicast Ready] 1 10/ EUP-101R Single Port over UTP Receiver [Multicast Ready] 1 10/ (IEEE802.3at input) ETP-2601T Premium Single Port over 2-Wire Transmitter 1 10/100 ETP-2601R Premium Single Port over 2-Wire Receiver 1 10/100 ETP-101T Single Port over 2-WireTransmitter [Multicast Ready] 95 *(270) 95 *(270) 600() 300() () 300() (IEEE802.3at input) 1 10/ ETP-101R Single Port over 2-Wire Receiver [Multicast Ready] 1 10/ (IEEE802.3at input) HPS-01 2 Port Hybrid Switch 2 10/ HPS-1008RM 8 Port Hybrid Switch 8 10/100/ EPR-1001 Single Port Gigabit repeater 1 10/100/ EPR-101 Single Port repeater 1 10/ EPR-111 Single Port repeater 1 10/ **(250) 100 **(250) 100 **(250) 100 **(250) 100 **(200) 100 **(250) 100 **(250) 100 **(250) 100 **(250) 100 **(200) 60 (IEEE802.3at input) - 60 (IEEE802.3at / DC56V input) 15 (IEEE802.3af input) 15 (IEEE802.3af input) f f f f ECP models are based on BNC for coaxial cable connection. EUP models are based on RJ45 for 4 pair UTP cable connection. ETP models are based on 2-Pin Terminal block for any 2-Wire of cable connection. Multi-port products may have dierent bandwidth and power for each port depending on number of connected cameras. Maximum distances for Data and are tested with RG-6 Coaxial cable, 4 Pair cable or 1 Pair cable. Test result may vary depending on cable type & quality. Max distance is tested with 7W IP. *( ) : Max. Bandwidth between Intercoax 2 series models. **( ) : Max. distance between Intercoax Repeaters. 3

6 & over Coax Premium Single Port over Coax Transceiver is a High-Speed, long distance & extender that makes possible to transmit IP data up to 2.4Km and up to 1.2Km through various analog cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over coax (UTP, 2-Wire) communication following IEEE1901 Standard Data + over Coax (or UTP, 2-wire) Data distance up to 2.4Km distance up to 1.2Km Max. 270Mbps Bandwidth 10/100/1000 Full Duplex bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.), +, Extra (Max. 60W output) Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Quality (Data & ) Plug & Play 12VDC output (for Non- ) Performance chart Model Transmission Rate Coax :1 Port Transceiver 1 x 75Ω BNC (Female) - over Coax (B-LinX) 1 x RJ45-10/100/1000 Base-T with Auto-detect MDIX 270Mbps Full Duplex (PHY: 500Mbps) 270 Mbps 200 Transmission Rate / meter RG-6 Coax 60W 30W (Watt) / meter RG-6 Coax 56VDC/1.2A Input Transmission Distance (PoC) up to 2.4Km(RG-6) up to 1.2Km (RG-6 / 7W camera) 1 x Data(Green) / 1 x (Yellow) W 10W EoC 1 x BNC Join(Green) 30 5W Link Quality 1 x PWR(Blue) 1 x Good(Green) / 1 x Bad(Red) m m Quality 12VDC out 1 x Good(Green) : 40V~57V / 1 x Bad(Red) : 40V Under 1 x 12V DC OUT(Green) Encryption 128-bit AES Supply Input B-Linx or DC12V~ 57V UTP ( - 4 Pair) Output DC Output Weight Support (15W), + (30W), Extra up to 60W DC12V / 2A 132(L) x 83(W) x 28(H)mm 198g 10/100 Non- 12V DC OUT IP BTE-02 Coax BTE-02 Supply Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification Optional Accessories FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) 56VDC / 1.2A External Supply Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 4 Network Solution Provider

7 & over Coax ECP-2704T Premium 4 Port over Coax Transmitter ECP-2704T is a 4 port High-Speed, long distance & transmitter that receives IP data from 4 dierent IP cameras or other network devices and transmits the EoC signal over one coaxial cable. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-2704T supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduce the construction cost significantly compared with fiber optic configuration. over coax (UTP, 2-Wire) communication following IEEE1901 Standard Data + over Coax (or UTP, 2-wire) Data distance up to 2.4Km distance up to 1.2Km Max. 270Mbps Bandwidth /100/1000 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.), +, Extra (Max. 60W output) Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Quality (Data & ) Plug & Play Over Current Protection for safe power transmission. 4 Port Output Model ECP-2704T: 4 Port Transceiver Coax Transmission Rate Transmission Distance (PoC) 1 x 75Ω BNC (Female) - over Coax (B-LinX) 4 x RJ45-10/100/1000 Base-T with Auto-detect MDIX 270Mbps Full Duplex (PHY: 500Mbps) up to 2.4Km(RG-6) up to 1.2Km (RG-6 / 7W camera) 4 x Data(Green) / 4 x (Yellow) ECP-2704T Supply Supply (Optional) Coax (or UTP / 2-Wire) EoC 1 x BNC Join(Green) Link Quality 1 x PWR(Blue) 1 x Good(Green) / 1 x Bad(Red) Quality 1 x Good(Green) : 40V ~ 57V / 1 x Bad(Red) : 40V Under Port 4 x Port 1 ~ Port 4(Green) Encryption 128-bit AES Input Output B-Linx or DC12V~ 57V Support (15W), + (30W), Extra up to 60W Weight 162.4(L) x 133.5(W) x 29.5(H)mm 343g Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply Multi-Port devices may have dierent bandwidth and power current for each port depending on number of connected cameras. Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 5

8 & over Coax ECP-2704R Premium 4 Port over Coax Receiver ECP-2704R is a 4 port Ultra High-Speed, long distance & receiver that receives 4 dierent signals from dierent EoC devices and transmits IP data to network switch or via RJ45 port. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-2704R supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With Smart Impedance Matching feature, the device maintains optimum signal level without any interference and Smart Over Current Protection (SOCP) feature makes the device to transmit power over coax safely. over coax (UTP, 2-Wire) communication following IEEE1901 Standard Data + over Coax (or UTP, 2-wire) Data distance up to 2.4Km distance up to 1.2Km Max. 270Mbps Bandwidth /100/1000 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) Up to 60W PoC ( over Coax) output Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Quality (Data & ) Plug & Play Over Current Protection for safe power transmission. Model ECP-2704R: 4 Port Receiver Coax (or UTP / 2-Wire) Coax 4 x 75Ω BNC (Female) - over Coax (B-LinX) 1 x RJ45-10/100/1000 Base-T with Auto-detect MDIX Transmission Rate 270Mbps Full Duplex (PHY: 500Mbps) Transmission up to 2.4Km(RG-6) ECP-2704R Distance (PoC) up to 1.2Km (RG-6 / 7W camera) 1 x Link(Yellow) / 1 x ACT(Green) Supply (Optional) Supply EoC 1 x BNC Join(Green) Link Quality 1 x PWR(Blue) 1 x Good(Green) / 1 x Bad(Red) 12V DC OUT Non- IP Quality Port 1 x Good(Green) : 40V~57V 1 x Bad(Red) : 40V Under 4 x Port 1 ~ Port 4(Green) Encryption Input Output Weight 128-bit AES DC12V~ 57V Support (15W), + (30W), Extra up to 60W 162.4(L) x 133.5(W) x 29.5(H)mm 360g Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply Multi-Port devices may have dierent bandwidth and power current for each port depending on number of connected cameras. Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 6 Network Solution Provider

9 & over Coax ECP-2601T/R Premium Single Port over Coax Transmitter / Receiver ECP-2601 is a High-Speed, long distance & extender that makes possible to transmit the signal up to 2.4Km and up to 1.2Km via Coax (or UTP, 2-wire) cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-2601 supports easy installation utilizing the existing cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over Coax communication following IEEE1901 Standard ECP-2601T Data + over Coax cable (or UTP, 2-Wire) Data distance up to 2.4Km distance up to 1.2Km Max. 95Mbps Bandwidth (270Mbps between Intercoax 2 series models) /100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.), +, Extra (Max. 60W output) ECP-2601R Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Quality (Data,, Link, ) Plug & Play Support + Input (25.5W) from PSE devices ECP-2601R Only Slim design Performance chart Transmission Rate Transmission Distance Model ECP-2601T ECP-2601R Coax (PoC) 1 x 75Ω BNC (Female) - over Coax (B-LinX) 1 x RJ45-10/100 Base-T with Auto-detect MDIX 95Mbps Full Duplex (270Mbps between Intercoax devices) up to 2.4Km(RG-6) up to 1.2Km (RG-6 / 7W camera) 95 Mbps Transmission Rate / meter RG-6 Coax 60W 30W 15W 10W (Watt) / meter RG-6 Coax 56VDC/1.2A Input EoC 1 x Data-Link (Yellow) 1 x Join-Link (Green) 1 x On(Amber) m 5W m 1 x Out (Red) Encryption 128-bit AES Input Output Weight B-Linx or DC12V~57V IEEE802.3af(), IEEE802.3at (+), Extra up to 60W 82.4(L) x 61.6(W) x 24(H)mm 77g Switch or DC12V~57V Not Supported PoC Only ECP-2601T Coax (or UTP / 2-Wire) Switch Supply ECP-2601R Environment Operating Temp -20 ~ 60 C Storage Temp -30 ~ 80 C ECP-2601T Coax (or UTP / 2 Wire) ECP-2601R Certification Optional Accessories FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) 56VDC / 1.2A External Supply Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 cable and 7 Watt IP. 7

10 & over Coax ECP-2808RM/2816RM Premium 8/16 Port over Coax Managed Receiving Switch (NMS) The All-New Intercoax ECP-2808RM/2816RM are 19 rack mountable Managed Long Distance and over Coax Receiving Switches. ECP-2808RM/2816RM are available with 8 or 16 B-Linx(Coax) ports. ECP-2808RM/2816RM are capable of connecting more than 8/16 ECP Transmitters even with Daisy-Chain connection and also support powered devices such as IP cameras. Data rates up to 1Gbps are achievable, making these devices the ideal choice in new or legacy installations where existing coax cable is re-deployed as part of an upgrade from Analog to IP cameras. ECP-2808RM has built-in 320 Watt power supply and ECP-2816RM has built-in 640 Watt power supply. Browser based GUI manages all connected IEEE1901-HPAV standard devices. Furthermore, the world first innovative Intercoax ECP Manager software allows managing multiple of ECP-2808RM /2816RM remotely from central management oice. REAR VIEW ECP-2808RM ECP-2816RM Total management software, Intercoax ECP Manager Full version included Friendly Graphic User with EasyView can easily access and monitor multiple ECP-2808RM/2816RM Configure Join & Unjoin, Changing joining password and power reset of remotely connected devices Real-time monitoring of power consumption for each port Multicast Setting with IGMP Query & Report Generator SNMP/SSH VLAN/QoS Port Locking by MAC Addresses Alarm & buzzer built-in switch and notification on ECP Manager Scheduled event reporting and alert reporting to designative users Back up & Restore of configuration 8/16 Port long distance EoC up to 2.4Km / +/ Extra up to 60W (++) per B-Linx port Each port has Auto Short Protection. When the cable is being shorted or damaged, it won t transmit power until the cable is fixed B-Linx Device Detection will secure the power transmission only to B-Linx devices 320W / 640W Built-in Supply Built-in crosstalk cancelling technology B-Linx Multiple Nodes can be used (Daisy Chain, Star, Etc.) on each port All IEEE1901-HPAV standard EoC devices can be easily connected remotely 19-inch(1U) rack mountable design Giga-bit SFP and Copper uplink port Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Performance chart ECP-2704T Coax Coax Coax ECP-2816RM 270 Mbps Transmission Rate / meter RG-6 Coax 60W 30W 15W (Watt) / meter RG-6 Coax 56VDC/1.2A Input Coax W 5W AC V m m Computer (NMS) The test result was conducted using as transmitter. 8 Network Solution Provider

11 & over Coax Model ECP-2808RM ECP-2816RM Coax Up-Link B-Linx / T-Linx Transmission Rate ( over Coax/UTP) B-Linx / T-Linx Communication Standard B-Linx / T-Linx Communication Modulation B-Linx / T-Linx Communication Multiple Nodes (Daisy Chain) ECP Manager Connectivity IGMP Data Transmission Distance Transmission Distance Coax 8 x 75Ω BNC (Female) - over Coax (B-Linx) 16 x 75Ω BNC (Female) - over Coax (B-Linx) 1 x RJ45-10/100/1000 Base-T with Auto MDIX, 1 x SFP Base-T UP to 560Mbps Full Duplex IEEE1901-HPAV OFDM UP to 1Gbps Full Duplex 2 remote transmitters per port recommended (Max up to 4 per port) Available IGMP (V1/V2/V3) Snooping, IGMP Query & Report Generator Up to 2.4Km (RG6) Coax Up to 1.2Km (RG6 / 7W) 1 x Blue Model ECP-2808RM ECP-2816RM Buzzer Event Buzzer / Mute Encryption AC Input DC output per Port Port Short Protection Smart B-Linx / T-Linx Device Detection Environment 128-bit AES AC100V-240V (50Hz/60Hz), 320W / 640W Max DC 57V (Max. 60W per port for support) Auto Detection & Protection Detection On / O 441.5(L) x 330(W) x 44(H)mm Weight 5,160g 5,600g Operating Temp -10~ 60 C Storage Temp -30 ~ 80 C Relative Humidity Certification Surge Protection 10% ~ 80% 441.5(L) x 330(W) x 44(H)mm CE (including Railways Standard EN ), FCC, KC IEC kV(1.2 / 50us), 2kA(8/20us) RJ45 Up-Link 1 x Green (10/100-Link) / 1 x Yellow (1000-Link) SFP Up-Link 1 x Green (1000-Link) Port 8 x Green 16 x Green Join 2 x Green 4 x Green Alarm 1 x Red Multi-Port devices may have dierent bandwidth and power current for each port depending on number of connected cameras. Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 2808RM / 2816RM Software INTERCOAX ECP Manager Professional management software for real-time monitoring, configuration and remote access. User Friendly GUI with Multiple 2808 / 2816 Series Remote access to connected devices and software based Joining ECP Configuration of Multiple 2808 / 2816 Series Remote device monitoring Receiver of selected 2808 / 2816 Series Status with history & Port reset 9

12 & over Coax ECP-9501T/R Single Port over Coax Transmitter / Receiver (Elevator) ECP-9501 is a High-Speed, long distance & extender that makes possible to transmit IP data up to 1000m and up to 1000m various analog cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-9501 supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over coax (UTP, 2-Wire) communication following IEEE1901 Standard ECP-9501T Data + over Coax (or UTP, 2-wire) Data distance up to 1000m distance up to 1000m 61.6 Max. 95Mbps Bandwidth 10/100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) ECP-9501R , +, Extra (Max. 60W output) (ECP-9501T only) Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Designed for elevator application exclusively. (Possible to reuse traveling cable for elevator) Plug & Play Over Current Protection for safe power transmission. Slim design Performance chart Transmission Rate Model ECP-9501T ECP-9501R Coax 1 x 75Ω BNC (Female) - over Coax 1 x RJ45-10/100 Base-T with Auto-detect MDIX 95Mbps Full Duplex (PHY: 200Mbps) 95 Mbps 60 Transmission Rate / meter RG-6 Coax 60W 30W (Watt) / meter RG-6 Coax 56VDC/1.2A Input Transmission Distance (PoC) EoC up to 1000m (RG-6) up to 1000m (RG-6 / 7W camera) 1 x Data(Green) 1 x (Yellow) 1 x BNC Join(Green) 1 x Link/Act(Green) 1 x 10/100(Yellow) m 15W 10W 5W m 1 x PWR(Blue) Encryption Input 128-bit AES B-Linx or DC12V~ 57V Output Support (15W), + (30W), Extra up to 60W Not Supported PoC Only Coax (or UTP / 2-Wire) Supply 82.4(L) x 61.6(W) x 24(H)mm Weight 110g 105g ECP-9501T ECP-9501R Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification Optional Accessories FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) 56VDC / 1.2A External Supply Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 10 Network Solution Provider

13 & over Coax ECP-9504R 4 Port over Coax Receiver ECP-9504R is a 4 port High-Speed, long distance & receiver that receives 4 dierent signals from ECP-9501 and transmits IP data to network switch or via RJ45 port. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-9504R supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With Smart Impedance Matching feature, the device maintains optimum signal level without any interference and Smart Over Current Protection (SOCP) feature makes the device to transmit power over coax safely. over coax (UTP, 2-Wire) communication following IEEE1901 Standard Data + over Coax (or UTP, 2-wire) Data distance up to 1000m distance up to 1000m Max. 95Mbps Bandwidth 10/100 Full Duplex bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) Up to 60W PoC ( over Coax) output Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Plug & Play Over Current Protection for safe power transmission. Slim design Compatible with EoC Transmitters such as ECP-9501T, ECP-8401T, ECP-8301EP, ECP-8301NP Model ECP-9504R: 4 Port Receiver Coax 4 x 75Ω BNC (Female) - over Coax (B-LinX) 1 x RJ45-10/100 Base-T with Auto-detect MDIX ECP-9501T Coax (or UTP / 2-Wire) Transmission Rate 95Mbps Full Duplex (PHY: 200Mbps) Transmission Distance (PoC) up to 1000m(RG-6) up to 1000m (RG-6 / 7W camera) ECP-9501T Supply 1 x Data(Green) EoC 1 x BNC Join(Green) 1 x PWR(Blue) ECP-8301EP Supply (Optional) ECP-9504R Encryption 128-bit AES Input PoC Output DC12V ~ 57V up to 60W ECP-8401T Weight 82.4(L) x 133.5(W) x 29.5(H)mm 360g Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply Multi-Port devices may have dierent bandwidth and power current for each port depending on number of connected cameras. Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 11

14 & over Coax ECP-9508R/9516R 8 / 16 Port over Coax Receiver ECP-9508R / ECP-9516R is multi-port High-Speed, long distance & unmanaged switch that receives 8 / 16 EoC Signal from ECP-9501 and transmit IP data to network switch or via RJ45 port. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-9508R / ECP-9516R supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With Smart Impedance Matching feature, the device maintains optimum signal level without any interference and Smart Over Current Protection (SOCP) feature makes the device to transmit power over coax safely. 19" Rack Mountable unmanaged switch over coax (UTP, 2-Wire) communication following IEEE1901 Standard Data + over Coax (or UTP, 2-wire) Data distance up to 1000m distance up to 1000m Max. 180Mbps / 360Mbps Bandwidth 130W / 260W Built-in supply 10/100/1000 Full Duplex 128bit AES network encryption FRONT VIEW Supports Multi-connection (Daisy chain, Star, etc.) Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Plug & Play REAR VIEW Over Current Protection for safe power transmission. ECP-9508R Compatible with EoC Transmitter such as ECP-9501T, ECP-8401T, ECP-8301EP, ECP-8301NP ECP-9516R Model Coax ECP-9508: 8 Port Receiver 8 x 75Ω BNC (Female) - EoC (B-LinX) ECP-9516R: 16 Port Receiver 16 x 75Ω BNC (Female) - EoC (B-LinX) 1 x RJ45-10/100/1000 Base-T with Auto-detect MDIX Transmission Rate 180Mbps Full Duplex 360Mbps Full Duplex Transmission up to 1000m(RG-6) Distance (PoC) up to 1000m (RG-6 / 7W camera) Encryption Environment 1 x ACT(Green) / 1 x Link(Yellow) 1 x POWER(Blue) Port 8 x 1~8 Port (Green) 16 x 1~16 Port (Green) Input Output 128-bit AES AC100V-240V (50Hz / 60Hz) Not Supported, PoC Only 432(L) x 265(W) x 44(H)mm Weight 3,150g 3,700g Operating Temp -10~ 60 C Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) 10/100 Coax (or UTP / 2-Wire) ECP-9501T AC/DC Adapter(12V) ECP-8301EP ECP-8301NP ECP-8401T AC V ECP-9516R Multi-Port devices may have dierent bandwidth and power current for each port depending on number of connected cameras. Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 12 Network Solution Provider

15 & over Coax ECP-8401T/R Single Port over Coax Transmitter / Receiver ECP-8401 is a High-Speed, long distance & extender that makes possible to transmit IP data up to 2.4Km and up to 1.2Km through various analog cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-8401 supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over coax (UTP, 2-Wire) communication following IEEE1901 Standard Data + over Coax (or UTP, 2-wire) Data distance up to 2.4Km distance up to 1.2Km Max. 80Mbps Bandwidth ECP-8401T 10/100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) 40.1, +, Extra (Max. 60W output) (ECP-8401T only) ON/OFF Switch - ECP-8401T model only ECP-8401R Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Quality Plug & Play Over Current Protection for safe power transmission. Support + Input (25.5W) from Switch ECP-8401R Only Ultra-Slim Design Performance chart Model ECP-8401T ECP-8401R Coax 1 x 75Ω BNC (Female) - over Coax (B-LinX) 1 x RJ45-10/100 Base-T with Auto-detect MDIX Transmission Rate 80Mbps Full Duplex (PHY: 200Mbps) 80 Mbps 60 Transmission Rate / meter RG-6 Coax 60W 30W (Watt) / meter RG-6 Coax 56VDC/1.2A Input Transmission Distance (PoC) up to 2.4Km(RG-6) up to 1.2Km (RG-6 / 7W camera) 40 15W 1 x Link(Yellow) 20 10W EoC 1 x Link(Green) 1 x On(Amber) m 5W m 1 x Output(Red) 1 x Input(Red) Encryption Input 128-bit AES B-Linx or DC12V~57V Output IEEE802.3af(), IEEE802.3at (+), Extra up to 60W Not Supported PoC Only Input Not Supported Up to 25.5W (PD) ECP-8401T Coax (or UTP / 2-Wire) ECP-8401R Supply Weight 66.4(L) x 40.1(W) x 25(H)mm 78g Switch Operating Temp -10 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply ECP-8401T Coax (or UTP / 2-Wire) ECP-8401R Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 13

16 & over Coax ECP-8301EP/NP Single Port over Coax Transmitter / Receiver ECP-8301 is a High-Speed, long distance & extender that makes possible to transmit IP data up to 2.4Km and up to 1.2Km through various analog cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-8301 supports easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire). With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over coax (UTP, 2-Wire) communication following IEEE1901 Standard ECP-8301EP Data + over Coax (or UTP, 2-wire) Data distance up to 2.4Km distance up to 1.2Km 61.6 Max. 80Mbps Bandwidth 10/100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) ECP-8301NP , +, Extra (Max. 60W output / ECP-8301EP only) ON/OFF Switch (ECP-8301EP only) Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Plug & Play Over Current Protection for safe power transmission. Performance chart Transmission Rate Model ECP-8301EP ECP-8301NP Coax 1 x 75Ω BNC (Female) - EoC (B-LinX) 1 x RJ45-10/100 Base-T with Auto-detect MDIX 80Mbps Full Duplex (PHY: 200Mbps) 80 Mbps 60 Transmission Rate / meter RG-6 Coax 60W 30W (Watt) / meter RG-6 Coax 56VDC/1.2A Input Transmission Distance (PoC) up to 2.4Km (RG-6) up to 1.2Km (RG-6 / 7W camera) W 10W EoC 1 x Data(Green) / 1 x (Yellow) 1 x BNC Join(Green) m 5W m 1 x PWR(Blue) Encryption Input 128-bit AES B-Linx or DC12V~ 57V Output Support (15W) + (30W) Extra up to 60W 82.4(L) x 61.6(W) x 24(H)mm Weight 103g 91g Not Supported PoC Only ECP-8301EP Coax (or UTP / 2-Wire) Supply ECP-8301NP Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply IP AC/DC Adapter(12V) ECP-8301NP Supply Coax (or UTP / 2-Wire) ECP-8301NP Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 14 Network Solution Provider

17 & over Coax ECP-101T/R Single Port over Coax Transmitter / Receiver (Multicast) ECP-101 Series are High-Speed, long distance & extender that makes possible to transmit the signal and up to 600m through Coax cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ECP-101 supports easy installation utilizing the existing Coax cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. ECP-101T Extension over existing coaxial cable Data + over Coaxial cable Data and distance up to 700m Max. 100Mbps Bandwidth /100 Full Duplex Multicast supported, +, Extra (Max. 60W output) (ECP-101T only) ECP-101R ON/OFF Switch (ECP-101T only) Quality (Data & ) 66.4 Plug & Play Support + Input (25.5W) from PSE devices ECP-101R Only Compact design Performance chart Transmission Rate Model ECP-101T ECP-101R Coax 1 x 75Ω BNC (Female) - over Coax (B-LinX) 1x RJ45-10/100 Base-T with Manual selection 10/100Mbps Full Duplex 100 Mbps Transmission Rate / meter RG-6 Coax 60W 30W (Watt) / meter RG-6 Coax 56VDC/1.2A Input Transmission Distance (PoC) up to 700 m (RG-6) up to 700 m (RG-6 / 15W output) 50 20W 15W 1 x Link / Act (Green) / 1 x (Green) 10 EoC 1 x Link (Blue) / 1 x Act (Green) m m 1 x On(Green) Input Output B-Linx or DC48V~57V IEEE802.3af(), IEEE802.3at (+), Extra up to 60W Not Supported PoC Only Input Not Supported Up to 25.5W (PD) Weight 66.4(L) x 61.6(W) x 24(H)mm 77g ECP-101T Coaxial Cable Switch Supply ECP-101R Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply ECP-101T Coaxial Cable ECP-101R Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on RG-6 coax cable and 7 Watt IP. 15

18 & over UTP EUP 2601T/R Premium Single Port over UTP Transmitter / Receiver EUP 2601 is a High-Speed, long distance & extender that makes possible to transmit the signal up to 1.2Km and up to 1.2Km via UTP cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since EUP 2601 supports easy installation utilizing the existing UTP cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over UTP communication following IEEE1901 Standard EUP-2601T Data + over UTP cable ( or better) Data distance up to 1.2Km distance up to 1.2Km Max. 95Mbps Bandwidth (270Mbps between Intercoax models) /100 Base-T with Auto-detect MDIX 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.), +, Extra (Max. 60W output) (EUP-2601T only) EUP-2601R ON/OFF Switch (EUP-2601T only) Quality (Data,, Link, ) Plug & Play Support + Input (25.5W) from PSE devices EUP 2601R Only Slim design Performance chart Transmission Rate Transmission Distance Model EUP 2601T EUP 2601R UTP 1 x RJ45 - over UTP (T-LinX) (PoC) 1 x RJ45-10/100 Base-T with Auto-detect MDIX 95Mbps Full Duplex (270Mbps between Intercoax 2 series models) up to 1.2 Km () up to 1.2 Km ( / 57VDC Input / 7W camera) 95 Mbps Transmission Rate / meter 60W 30W 15W 10W (Watt) / meter 56VDC/1.2A Input Data over 2-Wire 1 x Data-Link (Yellow) 1 x Join-Link (Green) 1 x On (Amber) m 5W m Output 1 x Out (Red) Encryption Input 128-bit AES T-Linx or DC12V~57V Switch or DC48V~57V Output IEEE802.3af(), IEEE802.3at (+), Extra up to 60W Not Supported Over UTP Only EUP-2601T UTP ( or Better) Supply EUP-2601R Weight 82.4(L) x 61.6(W) x 24(H)mm 102g Switch Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C EUP-2601T UTP ( or Better) EUP-2601R Certification Optional Accessories FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) 56VDC / 1.2A External Supply Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on cable and 7 Watt IP. 16 Network Solution Provider

19 & over UTP EUP 2808RM/2816RM Premium 8/16 Port over UTP Managed Receiving Switch (NMS) REAR VIEW EUP-2808RM EUP-2816RM The All-New Intercoax EUP 2808RM/2816RM are 19 rack mountable Managed Long Distance and over UTP Receiving Switches. EUP 2808RM/2816RM are available with 8 or 16 T-Linx(UTP) ports. EUP 2808RM/2816RM are capable of connecting more than 8/16 EUP Transmitters (or use ECP Transmitters with BTE-02) even with Daisy-Chain connection and also support powered devices such as IP cameras. Data rates up to 1Gbps are achievable, making these devices the ideal choice in new or legacy installations where existing UTP cable is re-deployed as part of an upgrade from Analog to IP cameras. EUP 2808RM has built-in 320 Watt power supply and EUP 2816RM has builtin 640 Watt power supply. up to 60W per port is available. Browser based GUI manages all connected IEEE1901-HPAV standard devices. Furthermore, the world first innovative Intercoax ECP Manager software allows managing multiple of EUP 2808RM /2816RM remotely from central management oice. Total management software, Intercoax ECP Manager Full version included Friendly Graphic User with EasyView can easily access and monitor multiple EUP 2808RM/2816RM Configure Join & Unjoin, Changing joining password and power reset of remotely connected devices Real-time monitoring of power consumption for each port Multicast Setting with IGMP Query & Report Generator SNMP/SSH VLAN/QoS Port Locking by MAC Addresses Alarm & buzzer built-in switch and notification on ECP Manager Scheduled event reporting and alert reporting to designative users Back up & Restore of configuration 8/16 Port long distance up to 1.2Km / +/ Extra up to 60W (++) per T-Linx port Each port has Auto Short Protection. When the cable is being shorted or damaged, it won t transmit power until the cable is fixed T-Linx Device Detection will secure the power transmission only to T-Linx devices 320W / 640W Built-in Supply Built-in crosstalk cancelling technology T-Linx Multiple Nodes can be used (Daisy Chain, Star, Etc.) on each port All IEEE1901-HPAV standard EoC devices can be easily connected remotely 19-inch(1U) rack mountable design Giga-bit SFP and Copper uplink port Supports UTP, Telephone (2 Pairs), 2-Wire cable communication (Using BTE Series) Performance chart AC V ECP-2704T BTE-02 BTE-02 or Better or Better or Better 95 Mbps Transmission Rate / meter 60W 30W 15W (Watt) / meter 56VDC/1.2A Input BTE-02 BTE-02 or Better m 10W 5W m EUP-2816RM Computer (NMS) 17

20 Model EUP 2808RM EUP 2816RM UTP Up-Link T-Linx Transmission Rate ( over UTP) T-Linx Communication Standard T-Linx Communication Modulation T-Linx Communication Multiple Nodes (Daisy Chain) ECP Manager Connectivity IGMP Data Transmission Distance Transmission Distance UTP 8 x 100Ω RJ45 (Female) - over UTP (T-LinX) 16 x 100Ω RJ45 (Female) - over UTP (T-LinX) 1 x RJ45-10/100/1000 Base-T with Auto MDIX, 1 x SFP Base-T UP to 560Mbps Full Duplex IEEE1901-HPAV OFDM UP to 1Gbps Full Duplex 2 remote transmitters per port recommended (Max up to 4 per port) Available IGMP (V1/V2/V3) Snooping, IGMP Query & Report Generator Up to 1.2Km () UTP Up to 1.5Km ( / 7W) 1 x Blue Model EUP 2808RM EUP 2816RM Buzzer Event Buzzer / Mute Encryption AC Input DC output per Port Port Short Protection Smart T-Linx Device Detection Environment 128-bit AES AC100V-240V (50Hz/60Hz), 320W / 640W (Redundancy power option) Max DC 57V (Max. 60W per port for support) Auto Detection & Protection Detection On / O 441.5(L) x 330(W) x 44(H)mm Weight 5,110g 5,540g Operating Temp Storage Temp Relative Humidity Certification Surge Protection -10~ 60 C -30 ~ 80 C 10% ~ 80% 441.5(L) x 330(W) x 44(H)mm CE (including Railways Standard EN ), FCC, KC IEC kV(1.2 / 50us), 2kA(8/20us) RJ45 Up- Link SFP Up-Link 1 x Green (10/100-Link) / 1 x Yellow (1000-Link) 1 x Green (1000-Link) Port 8 x Green 16 x Green Join 2 x Green 4 x Green Alarm Red Multi-Port devices may have dierent bandwidth and power current for each port depending on number of connected cameras. Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on cable and 7 Watt IP. 2808RM / 2816RM Software INTERCOAX ECP Manager Professional management software for real-time monitoring, configuration and remote access. User Friendly GUI with Multiple 2808 / 2816 Series Remote access to connected devices and software based Joining ECP Configuration of Multiple 2808 / 2816 Series Remote device monitoring Receiver of selected 2808 / 2816 Series Status with history & Port reset 18 Network Solution Provider

21 & over UTP EUP 8401T/R Single Port over UTP Transmitter / Receiver EUP 8401 is a High-Speed, long distance & extender that makes possible to transmit the signal up to 1.2Km and up to 1.2Km via UTP cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since EUP 8401 supports easy installation utilizing the existing UTP cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over UTP communication following IEEE1901 Standard Data + over UTP cable ( or better) EUP-8401T Data distance up to 1.2Km distance up to 1.2Km Max. 80Mbps Bandwidth /100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) EUP-8401R , +, Extra (Max. 60W output) (EUP-8401T only) ON/OFF Switch (EUP 8401T only) Quality Plug & Play Over Current Protection for safe power transmission. Support + Input (25.5W) from PSE devices EUP 8401R Only Ultra-Slim Design Performance chart Model EUP 8401T EUP 8401R EoC Signal 1 x RJ45 - over Coax (T-LinX) 1 x RJ45-10/100/1000 Base-T with Auto-detect MDIX Transmission Rate 80Mbps Full Duplex (PHY: 200Mbps) Transmission up to 1.2Km(Cat.5 / ) Distance (PoC) up to 1.2Km ( / 7W camera) 80 Mbps Transmission Rate / meter 60W 30W 15W (Watt) / meter 56VDC/1.2A Input 1 x Link(Yellow) 20 10W EoC 1 x Join(Green) 1 x On(Amber) m 5W m 1 x Output(Red) 1 x Input(Red) Encryption 128-bit AES Input T-Linx or DC12V~57V Switch or DC12V~57V Output Support (15W), + (30W), Extra up to 60W Not Supported PoC Only Input Not Supported Up to 25.5W (PD) EUP-8401T or Better EUP-8401R Supply Weight 66.4(L) x 40.1(W) x 25(H)mm 78g Operating Temp -10 ~ 60 C Environment Storage Temp -40 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply EUP-8401T or Better EUP-8401R Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on cable and 7 Watt IP. 19

22 & over UTP EUP 101T/R Single Port over UTP Transmitter / Receiver (Multicast) EUP 101 Series are High-Speed, long distance & extender that makes possible to transmit the signal and up to 600m through UTP cables in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since EUP 101 supports easy installation utilizing the existing UTP cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. EUP-101 T Extension using UTP cable ( or better) Data + over UTP cable Data and distance up to 600m Max. 100Mbps Bandwidth /100 Full Duplex Multicast supported, +, Extra (Max. 60W output) (EUP-101T only) EUP-101 R ON/OFF Switch (EUP-101T only) Quality (Data & ) Plug & Play Support + Input (25.5W) from PSE devices EUP 101R Only Compact design Performance chart Model EUP 101T EUP 101R EoC Signal 1 x RJ45 - over UTP (T-LinX) 1 x RJ45-10/100 Base-T with manual Transmission Rate 10/100Mbps Full Duplex Transmission up to 600 m (Cat5e UTP Cable) Distance (PoC) up to 600 m ( / 20W) 100 Mbps 50 Transmission Rate / meter 60W 30W 20W 15W (Watt) / meter 56VDC/1.2A Input 1 x Link / Act (Green) / 1- (Green) 1 x Link (Blue) / 1- Act (Green) x On(Green) Input Output DC48V~57V IEEE802.3af (), IEEE802.3at (+), Extra up to 60W Not Supported PoC Only Input Not Supported Up to 25.5W (PD) Weight 82.4(L) x 61.6(W) x 24(H)mm 70g EUP-101T Cat.5 or better Supply Switch EUP-101R Operating Temp -20 ~ 60 C Environment Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply EUP-101T Cat.5 or better EUP-101R Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on cable and 7 Watt IP. 20 Network Solution Provider

23 & over 2-Wire ETP-2601T/R Premium Single Port over 2-Wire Transmitter / Receiver ETP-2601 Series are High-Speed, long distance & extender that makes possible to transmit the signal and via 2-Wire cable (Twisted pair cable, COM, line) in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ETP-2601 supports easy installation utilizing the existing cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. over 2-Wire communication following IEEE1901 Standard Data + over 2-Wire cable (UTP, COM, Line, etc.) TOPVIEW ETP-2601T Supports long distance Untwisted/Twisted 2-Wire cables Data distance up to 600m distance up to 300m 61.6 Max. 95Mbps Bandwidth (270Mbps between Intercoax 2 series models) 10/100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) ETP-2601R, +, Extra (Max. 60W output) (ETP-2601T only) ON/OFF Switch (ETP-2601T only) Quality (Data,, Link, ) Plug & Play Support + Input (25.5W) from PSE devices ETP-2601R Only Slim design Transmission Rate Transmission Distance Encryption Environment Model ETP-2601T ETP-2601R 1 x 2-Pin Terminal Block - over 2-Wire 2-Wire (T-LinX) 2-Wire (PoC) Data over 2-Wire Output Input Output 1 x RJ45-10/100 Base-T with Auto-detect MDIX 95Mbps Full Duplex (270Mbps between Intercoax 2 series models) up to 600 m(twisted Pair Cable/) up to 300 m ( / 7W camera) 1 x Data-Link (Yellow) 1 x Join-Link (Green) 1 x On (Amber) 1 x Out (Red) 128-bit AES T-Linx or DC12V~57V IEEE802.3af(), IEEE802.3at (+), Extra up to 60W Switch or DC48V~57V Not Supported Over 2-Wire Only Input Not Supported Up to 25.5W (PD) Weight Optional Accessories 80.4(L) x 61.6(W) x 24(H)mm 102g Operating Temp -20 ~ 60 C Storage Temp -30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) 56VDC / 1.2A External Supply Performance chart 95 Mbps Transmission Rate / meter (1Pair) 60W 30W 15W 10W 5W (Watt) / meter (1Pair) 56VDC/1.2A Input m m ETP-2601T ETP-2601T 2-Wire (or UTP / COM / Line) Supply Switch 2-Wire (or UTP / COM / Line) ETP-2601R ETP-2601R Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. Distance is based on (1 Pair) cable and 7 Watt IP. 21

24 & over 2-Wire ETP-101T/R Single Port over 2-Wire Transmitter / Receiver (Multicast) ETP-101T/R is a High-Speed, long distance & extender that makes possible to transmit the 100Mbps signal and up to 300m via 2-Wire cable (Twisted pair cable, COM, line) in dierent situations. It is cost-eective and time saving solution to migrate existing analog system to IP based system since ETP-101T/R supports easy installation utilizing the existing cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly. ETP-101 T Extension over 2-Wire Cable (Twisted Pair, COM, Alarm, line, etc.) Data + over 2-Wire cable Data & distance up to 300m (Twisted Pair) 61.6 Max. 100Mbps Bandwidth 10/100 Full Duplex Multicast Supported ETP-101 R , +, Extra (Max. 60W output) (ETP-101T only) ON/OFF Switch (ETP-101T only) Quality (Data,, Link, ) Plug & Play Support + Input (25.5W) from PSE devices (ETP-101R Only) Compact Design Performance chart Transmission Rate Transmission distance Model ETP-101T ETP-101R EoC Signal (PoC) 1 x 2-Pin Terminal Block over 2-Wire cable 1 x RJ45 10/100 Base-T with manual selection 10/100Mbps Full Duplex Up to 300m (1 Pair of ) Up to 300m (1 Pair of / 7W ) 100 Mbps 50 Transmission Rate / meter 60W 30W 20W 15W (Watt) / meter 56VDC/1.2A Input 1 x Link / Act (Green) / 1 x (Green) 1 x Link (Blue) / 1 x Act (Green) m m 1 x On(Green) Input Output DC48V~57V IEEE802.3af (), IEEE802.3at (+), Extra up to 60W Not Supported PoC Only Input Not Supported Up to 25.5W (PD) Weight 82.4(L) x 61.6(W) x 24(H)mm 70g ETP-101T 25 Pair Bundle Cable ( or better) ETP-101R Supply Operating Temp. -20 ~ 60 C Environment Storage Temp. -30 ~ 80 C ETP-101T ETP-101R Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Switch Optional Accessories 56VDC / 1.2A External Supply 22 Network Solution Provider

25 Hybrid Switch HPS-01 2 Port Hybrid Switch (NMS) The HPS-01 is a 2Port Hybrid Switch that transmits network signal and + power up to 250 meters between the devices. 1 input 2 output design makes easy to install 2 network devices into a single LAN cable and possible to connect multiple devices in a cascade configuration. With built-in standard PD, the device supports secure + power supply and outputs up to 25.5W. The NMS (Network Management System) feature with the Browser based GUI & the exclusive Management software allow monitoring and managing multiple Hybrid Switches remotely from central oice. 1 input 2 output design (Possible to connect 2 network devices using 1 cable) Extended transmission distance up to 250m (Configured with the Hybrid Switch Series) 10/100 Base-T (Full Duplex), +, Extra (Max. 60W output), + input 61.6 DC48~57V power input Cascade configuration Over current protection for secured power supply NMS (Network Management System) by IP address - Connection Status monitoring - Transmission Bandwidth per port monitoring - Reset per each port - Device ID setting - Event & Alarm - consumption monitoring - SNMP - Default Setting (User, Factory) Model Downlink Uplink HPS-01: 2 Port Hybrid Switch 2 x RJ-45 1 x RJ-45 10/100 Base-T with Auto-detect MDIX Supply (Optional) Transmission Rate Transmission distance / 100 Mbps Full Duplex Up to 100m Base-T Up to 250m between devices 10/100 Base-T Max. 130m HPS-01 or Better Max. 250m HPS-01 Data 3 x Data Link (Green) 3 x Link (Amber) Input DC IEEE802.3af(), IEEE802.3at (+) DC48V ~ 57V HPS-01 Output IEEE802.3af(), IEEE802.3at (+), Extra up to 60W (Using PF : 56VDC / 1.2A power supply) Max. 130m Weight 80.4(L) x 61.6(W) x 24(H) mm 102g Switch Environment Operating Temp ~ 60 C Storage Temp ~ 80 C Computer (NMS) Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) Optional Accessories 56VDC / 1.2A External Supply Transmission distance may vary depending on the type and quality of cable. 23

26 Hybrid Switch HPS-1008RM 8 Port Hybrid Switch (NMS) The HPS-1008RM is a 19" rack mountable 8 +2 port Gigabit Hybrid Switch that transmits 1Gbps and supports +(up to 25.5W) Using HPS-01 (2 Port Hybrid Switch), the device supports 100Mbps transmission and + power supply up to 250 meters and it is possible to connect multiple devices in cascade mode. With the built-in standard PSE and the over current protection function, the device supplies secured + power up to 25.5W by each port. The NMS (Network Management System) feature with the Browser based GUI & the exclusive Management software allow monitoring and managing multiple Hybrid Switches remotely from central oice. Gigabit 8+2 port Switch - Downlink(1Gbps): 8 x RJ45, 2 x SFP - Uplink(1Gbps): 2 x RJ45, 1 x SFP 10/100/1000 (Full Duplex) Extended (100Mbps) distance up to 250 m (With the HPS-01: 2 port Hybrid Switch) Cascade configuration (With the HPS-01: 2 port Hybrid Switch), + output up to 25.5W Over current protection for secured power supply REAR VIEW NMS (Network Management System) - Connection Status monitoring - Transmission Bandwidth per port monitoring - Reset per each port - Device ID setting - Event & Alarm - consumption monitoring - SNMP - Default Setting (User, Factory) - e-map Model Transmission Rate Transmission Distance Input Output Environment Downlink Uplink / (Downlink) (Uplink) Output PWR Input Weight HPS-1008RM: 8 Port Hybrid Switch 8 x RJ-45 10/100/1000 Base-T with Auto-detect MDIX 2 x SFP 1000 Base-FX 2 x RJ-45 10/100 Base-T with Auto-detect MDIX 1 x SFP 1000 Base-FX 1Gbps Full Duplex Up to 100m Up to 250m with HG-01 (2 Port Hybrid Switch) 8 x RJ45 Data Link (Green) 2 x SFP Data Link (Green) 2 x RJ45 Data Link (Green) 1 x SFP Data Link (Green) 8 x Output (Amber) 1 x Input (Blue) AC100V-240V (50Hz/60Hz), 250W SMPS IEEE802.3af(), IEEE802.3at (+ / up to 25.5W) 430.5(L) x 280(W) x 44(H) mm 102g Operating Temp -10~ 60 C Storage Temp - 30 ~ 80 C Certification FCC, CE, KC IEC kV(1.2 / 50us), 2kA(8 / 20us) PTZ IP PTZ IP ECP-8401T HPS-01 HPS-01 Coax/UTP/2-Wire Max. 1000m Max. 250m PTZ IP ECP-8401R UTP Cable () Max. 250m HPS-01 Computer (NMS) Max. 250m AC V HPS-1008RM Transmission distance may vary depending on the type and quality of cable. 24 Network Solution Provider

27 Hybrid Switch EPR-1001 Gigabit & + Repeater EPR-1001 is a Gigabit (10/100/1000) & + Repeater that make possible to overcome max. 100m distance limitation of the standard network configuration. For more distance extension, the devices can be added by daisy-chaining (up to 750m) and possible to configure an IP extension easily. It is cost eective and easy installation solution for all kind of (IEEE802.3af), + (IEEE802.3at) compliant devices and the device outputs high power (up to 60W) by using 56VDC /1.2A supply. Gigabit & Repeater Up to 250 meter & Extension Additional extension by adding devices (Up to 750m / 250m extension between devices) 83 IEEE802.3af (15W) / IEEE802.3at (25.5W) / Up to 60W output (Using 56VDC / 1.2A supply) output On / O Switch, + Input (From Switch, Injector) DC input supported (DC12~57V) 83 Model EPR-1001 LAN / In LAN / Out 1 x RJ45-10/100/1000 Base-T with Auto-detect MDIX 1 x RJ45-10/100/1000 Base-T with Auto-detect MDIX EPR-1001 Max. 250m EPR-1001 Transmission Rate 1Gbps Full Duplex Transmission Distance 100m **(250m) Network Switch 1 x Data(Green) 1 x (Yellow) Supply Standards IEEE802.3af / IEEE802.3at Max. Max. 25.5W () / 60W (DC 57V/1.2A ) 82(L) x 83(W) x 28(H)mm Weight 118g EPR-1001 Max. 250m EPR-1001 Operating Temp -20 ~ 60 C Environment Storage Temp -20 ~ 80 C f f **( ) : Max. distance between Intercoax Repeaters Transmission distance may vary depending on the type and quality of cable, use of power and environmental condition. 25

28 Hybrid Switch EPR-101/111 & Repeater EPR-101 EPR Transmission Rate Model EPR-101 EPR-111 LAN / In LAN / Out 1 x RJ45-10/100 Base-T with Auto-detect MDIX 1 x RJ45-10/100 Base-T with Auto-detect MDIX 100Mbps Full Duplex Transmission Distance 100m **(250m) 100m **(200m) f f Environment Standards Max. 1 x Data(Green) 1 x (Yellow) IEEE802.3af() Max. 15W 82(L) x 83(W) x 28(H)mm Weight 118g 72.5g Operating Temp -20 ~ 60 C Storage Temp -20 ~ 80 C **( ) means Max distance between EPR series. 66.4(L) x 40.9(W) x 21.8(H)mm EPR Series are & Repeaters that make possible to overcome max. 100m distance limitation of the network configuration. For more distance extension, the devices can be added by daisy-chaining (up to 750m). It is cost eective and easy installation solution for all kind of (IEEE802.3af / 15W) compliant devices such as IP cameras,, VoIP Phone, etc. & Repeater Up to 250m & extension (EPR-111: 200m) Additional extension by adding devices 15W output (IEEE802.3af) On/O switch supported (EPR-101 only) No additional power required ( powered) Slim design (EPR-111) EPR-111 Max. 200m EPR-111 Network Switch EPR-101 Max. 250m EPR-101 Transmission distance may vary depending on the type and quality of cable, camera and environmental condition 26 Network Solution Provider

29 Others PF VDC/1.2A Supply PF is a premium power supply unit designed for INTERCOAX Extender Series. PSU meets the power requirement of CCTV products that require IEEE802.3af, IEEE802.3at, and Extra power (up to 60W). 56VDC / 1.2A supply Plug Polarity : DC Cord: UL1185, 18AWG, 0D3.5 Plug: 5.5 x 2.1 x 10 mm Case & Cord Color: Black ,480~1,520 SIDE VIEW Model PF Input Range Input Plug 120~240Vac, 50/60Hz 3Pin Inlet Type Maximum 67.2W Output Voltage DC 56V Output Current 1.2A Over current protection Over voltage protection Energy Eiciency Level Average Eiciency Safely Standards 120%~300% (max) 120%~200% (max) LEVEL V 87% (min) UL, CE, KC, PSE 115 x 55 x 31mm Operating temperature 0~40 C Operating Humidity MTBF 0~85%(Non-condensing) Hrs 27

30 Others BTE-02/03/04 Single Port BNC to RJ-45 / RJ-11 / Terminal Block Exchanger BTE-02 BTE-03 BTE-04 BTE-02 BTE-03 BTE BTE-02/03/04 is BNC to RJ-45 / RJ-11 / 2-Pin Terminal Block Exchanger that supports B-Linx signal and power transmission over UTP cable / Telephone wire / any kind of 2-Wire cable. This exchanger works with Intercoax ECP series exclusively to use various new or existing cables in the field instead of Coaxial cable and it maintains optimum B-Linx signal without interference using impedance matching technology. Performance chart (with BTE-02) 270 Mbps Transmission Rate / meter 60W 30W 15W (Watt) / meter 56VDC/1.2A Input BNC to RJ-45 (4 Pair cable) / RJ-11 (2 Pair cable) / Terminal block (1 Pair cable) Exchanger m 10W 5W m Specialized Impedance Matching Technology (Maintain optimum signal without interference). Crosstalk cancellation Technology indication Exclusively compatible with Intercoax ECP-28XX, 27XX, 95XX, 84XX, 83XX series. 4Pair UTP cable Supply Model BTE-02 BTE-03 BTE-04 Coax 75Ω BNC (Male) - over Coax BTE-02 BTE-02 Supply Pair cable RJ45 (4 Pair) Blue On: Normal RJ11 (2 Pair) 2-Pin Terminal Block (1 Pair) BTE-03 Telephone Cable BTE-03 Max. Current (W) Up to 60W power over cable Supply Environment Weight 60(L) x 24(W) x 24.5(H)mm 30g Operating Temp -20 ~ 60 C Storage Temp -40 ~ 80 C BTE-04 2-Wire Cable BTE-04 Relative Humidity 0% ~ 95% 28 Network Solution Provider

31 Others ERM Port 19 /2U Rack Mount Bracket (for ECP/EUP 101R) ERM-800 is 19 (2U) size 8ch rack mountable bracket for up to 8 units of ECP/EUP receivers and 8 units of PF ( supply) installation. ERM-800 provides ease of installation in the field where multiple receivers installation required. 8 Port 19 /2U Rack Mountable Bracket. Exclusive design for ECP-101R & EUP 101R. Up to 8 units of EoC receivers can be installed. Up to 8 units of PF ( supply) can be installed. Provide detachable mounting bracket for EoC receivers and power supply. Provide ease of installation for multiple devices. FRONT VIEW Model ERM-800 Port Detachable Bracket EoC Receivers Supply 8 Port 8 EA (Exclusively for ECP-101R, EUP 101R) 8 EA Weight 2,450g 438(L) x 400(W) x 87.5(H) mm 29

32 Applications Coax / UTP / 2-Wire Communication Supply Coaxial cable RG58, RG59, RG6, RG11 Supply UTP cable BTE-02 or Better BTE-02 Supply 2-Wire BTE-04 Line, COM Line BTE-04 4 Port over Coax Transmitter configuration Supply (Optional) Cat. 5e RG-6 Coaxial cable Max. 2,400m ECP-2704T Supply 4 Port over Coax Receiver configuration Cat. 5e RG-6 Coaxial cable Max. 600m ECP-2704R Supply (Optional) Supply 30 Network Solution Provider

33 Applications Data + over Coax Configuration Supply RG-6 Coaxial cable 7Watt Max. 1,200m ECP-8301NP ECP-8301EP DC Adapter(12V) RG-6 Coaxial cable Supply Non- Max. 2,400m ECP-8301NP ECP-8301EP 4:1 Daisy Chain Connection with T-Splitter Cat. 5e RG-6 Coaxial cable ECP-9501T Max. 200m ECP-9501T Supply (Optional) Max. 200m ECP-9501T Max. 200m Supply ECP-9501T Max. 200m ECP-9501R Cat. 5e 31

34 Applications 16 Port Receiver Configuration Coaxial cable AC V ECP-2601T / ECP-2601T 4 Pair UTP Cable (CAT.5e) Wifi AP EUP-2601T BTE-02 Telephone Cable VoIP Phone ECP-2601T BTE-03 BTE-03 2-Wire Cable Access Control ETP-2601T BTE-04 Access Control ETP-2601T ECP-2816RM 4:1 Configuration over 4 Pair UTP cable ETP-2601T ETP-2601T Supply 4 Pair UTP cable / ETP-2601T ETP-2601R ETP-2601T switch 32 Network Solution Provider