Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Hardware Installation Guide

Transcription

1 Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Hardware Installation Guide December 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax:

2 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. Modifying the equipment without Cisco s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: Turn the television or radio antenna until the interference stops. Move the equipment to one side or the other of the television or radio. Move the equipment farther away from the television or radio. Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB s public domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iphone, IP/TV, iq Expertise, the iq logo, iq Net Readiness Scorecard, iquick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0711R) Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental Cisco Systems, Inc. All rights reserved.

3 CONTENTS Preface vii Audience i-vii Purpose i-vii Organization i-vii Conventions i-viii Related Publications i-viii Obtaining Documentation and Submitting a Service Request i-ix CHAPTER 1 Product Overview 1-1 Switch Features Overview 1-1 Other Features 1-3 Switch Console Port /100/1000 Ports Gigabit Ethernet Module Slots 1-4 LEDs 1-4 StackWise Plus Ports 1-8 Power Connectors 1-8 Management Options 1-8 Using the Device Manager 1-8 Using the Command-Line Interface 1-9 Using the Dell CMC 1-9 Other Management Options 1-10 Network Configurations 1-10 CHAPTER 2 Switch Installation 2-1 Safety Warnings 2-1 Dell Modular Server Chassis Architecture 2-3 Installing the Switch in the Server Chassis 2-4 Configuring the Switch 2-7 Connecting through the Switch Console Port 2-8 Waiting for POST to Complete 2-10 Completing the Initial Configuration 2-10 iii

4 Contents Using the Device Manager to Configure the Switch 2-13 Configuring the Switch Stack Master 2-15 Managing the Switch 2-15 Using the CLI 2-15 Using the Device Manager 2-16 Other Management Options 2-16 Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S Switches) 2-17 Stack Cabling Configurations 2-18 Connecting the StackWise Plus Cables 2-21 Installing Devices in the 10-Gigabit Ethernet Slots 2-21 Installing X2 Transceiver Modules and Cisco Converter Modules 2-22 Installing SFP Modules 2-25 Connecting to 10/100/1000 Ethernet Ports 2-27 Where to Go Next 2-27 CHAPTER 3 Troubleshooting 3-1 Diagnosing Problems 3-1 Verify the Switch POST Results 3-1 Look at the Switch LEDs 3-2 Confirm the Switch Connections 3-2 Verify the Switch Performance 3-4 Clearing the Switch IP Address and Configuration 3-4 Replacing a Failed Stack Member 3-5 Locating the Switch Serial Number 3-5 APPENDIX A Technical Specifications A-1 APPENDIX B Connector and Cable Specifications B-1 Connector Specifications B-1 10/100/1000 Ports B-1 10-Gigabit Ethernet Module Interfaces B-3 Cisco TwinGig Converter Module Ports B-3 Console Port B-4 Cable and Adapter Specifications B-4 10-Gigabit Ethernet X2 Transceiver Module Cable Specifications B-4 SFP Module Cable Specifications B-6 Two Twisted-Pair Cable Pinouts B-6 Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports B-7 iv

5 Contents Identifying a Crossover Cable B-8 Console Port Adapter Pinouts B-8 I NDEX v

6 Contents vi

7 Preface Audience This guide is for the networking or computer technician responsible for installing the Cisco Catalyst Blade Switch 3130 for Dell or the Cisco Catalyst Blade Switch 3032 for Dell, referred to as the switch, in the Dell Modular Server Chassis, referred to as the server chassis. We assume that you are familiar with the concepts and terminology of Ethernet and local area networking. If you are interested in more training and education in these areas, learning opportunities including training courses, self-study options, seminars, and career certifications programs are available on the Cisco Training & Events web page: Purpose This guide describes the hardware features of the Cisco Catalyst Blade Switch 3130 for Dell or the Cisco Catalyst Blade Switch 3032 for Dell. It describes the physical and performance characteristics of the switch module, explains how to install it in the server enclosure, and provides troubleshooting information. This guide does not describe system messages that you might receive or how to configure your switch module. For more information, see the switch software configuration guide, the switch command reference, and the switch system message guide on the Cisco.com Product Documentation home page at: Organization This guide is organized into these chapters: Chapter 1, Product Overview, is a physical and functional overview of each of the switch modules, including descriptions of the ports, the supported standards, and the LEDs. Chapter 2, Switch Installation, contains the procedures on how to install the switch module in the server enclosure and how to make port connections. Chapter 3, Troubleshooting, describes how to identify and resolve some of the problems that might arise when you install the switch module. vii

8 Conventions Preface Appendix A, Technical Specifications, lists the physical and environmental specifications for the switch modules and the regulatory agency approvals. Appendix B, Connector and Cable Specifications, describes the connectors, cables, and adapters that can be used to connect to the switch module. Conventions This document uses these conventions and symbols for notes, cautions, and warnings: Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual. Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS (Statement 1071) The safety warnings for this product are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for Dell that ships with the product. The EMC regulatory statements are also included in that guide. Related Publications These documents provide complete information about the switch module and are available from Cisco.com: Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for Dell Release Notes for the Cisco Catalyst Blade Switch 3130 for Dell and the Cisco Catalyst Blade Switch 3032 for Dell Note Before you install, configure, or upgrade the switch module, see the release notes on Cisco.com for the latest information. Cisco Catalyst Blade Switch 3130 for Dell Software Configuration Guide Cisco Catalyst Blade Switch 3130 for Dell Command Reference viii

9 Preface Obtaining Documentation and Submitting a Service Request Cisco Catalyst Blade Switch 3130 for Dell System Message Guide Cisco Software Activation Document for Dell These compatibility matrix documents are available from this Cisco.com site: Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix Cisco Small Form-Factor Pluggable Modules Compatibility Matrix Compatibility Matrix for 1000BASE-T Small Form-Factor Pluggable Modules Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: Subscribe to the What s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. ix

10 Obtaining Documentation and Submitting a Service Request Preface x

11 CHAPTER 1 Product Overview This chapter provides a functional overview of the Cisco Catalyst Blade Switch 3130 for Dell and the Cisco Catalyst Blade Switch 3032 for Dell, referred to as the switch and how to set up and configure your switch. The switches are installed in the Dell Modular Server Chassis hereafter referred to as the server chassis a system that supports up to sixteen server modules and up to six Ethernet switches. You can connect the uplink ports to other devices such as switches, routers, Cisco Wireless Access Points, workstations, Cisco IP phones, or other networking equipment. You can also connect standalone servers or PCs to those ports. These topics are included: Switch Features Overview, page 1-1 Other Features, page 1-3 Management Options, page 1-8 Switch Features Overview These are the available switch models: Model CBS3032G CBS3130G-S CBS3130X-S Description 1-Gigabit Ethernet nonstacking-capable switch. This switch supports only the IP base software image. 1-Gigabit Ethernet stacking-capable switch. 10-Gigabit Ethernet stacking-capable switch. The Cisco Catalyst Blade Switch 3032G and 3130G support only the Cisco TwinGig Converter Modules, not the X2 transceiver modules. The switch runs the universal software image that has the Cisco IOS code for multiple feature sets. To enable a specific feature set, you must use the software activation feature to install the software license for that feature set. For more information, see the Cisco Software Activation Document for Dell, the release notes, and the software configuration guide on Cisco.com. Each external port has an associated LED. The System Status/ID LED is controlled by the Chassis Management Controller (CMC), also referred to as the Dell Remote Access Controller/Modular Chassis (DRAC/MC) management board. For more information about the LEDs and their meanings, see the switch hardware installation guide on Cisco.com. 1-1

12 Switch Features Overview Chapter 1 Product Overview For a list of supported modules, see the release notes on Cisco.com. For detailed instructions on installing, removing, and connecting to SFP modules, see the documentation that came with the SFP module. Figure 1-1 shows the Cisco Catalyst Blade Switch 3130 for Dell. The Cisco Catalyst Blade Switch 3032 for Dell does not have the StackWise Plus ports and Stack, Master, and Member LEDs. Figure 1-1 CBS3130 Switch Front Panel STK X 19X 21 X X WS-CBS3130X-S 20X 22 K 23 X2-2 R M MB M ST S TC S YS T R MODE CONSOLE Switch 8 Release latch 2 StackWise Plus ports 1 and 2 (only the CBS3130G-S and 9 Cisco status LEDs CBS3130X-S switches) 3 Gigabit Ethernet uplink ports 17 to 20 and port LEDs 10 System Status/ID LED 1 4 LEDs for ports 21 and 22 or for 10-Gigabit Ethernet slot 1 11 Mode button 5 Gigabit Ethernet ports 21 and 22 or 10-Gigabit Ethernet slot Console port 6 LEDs for ports 23 and 24 or for 10-Gigabit Ethernet slot 2 13 Power LED 7 10-Gigabit Ethernet slot 2 or Gigabit Ethernet ports 23 and SYST, STCK, MSTR, MMBR Gigabit Ethernet supported only on the CBS3130X-S. Table 1-1 describes the switch ports. Table 1-1 Port Ports 1 to 16 Ports 17 to 20 Ports 21 to 24 Cisco Catalyst Blade Switch 3130 for Dell and 3032 for Dell Port Descriptions Description Internal Gigabit Ethernet 1000BASE-X downlink ports that connect the switch to the server chassis blades. External 10/100/1000BASE-T copper Gigabit Ethernet uplink ports that support auto-mdix and autonegotiation. 10-Gigabit Ethernet module slots for use with the Cisco TwinGig Converter Modules and Cisco X2 transceiver modules. 1-2

13 Chapter 1 Product Overview Other Features Table 1-1 Cisco Catalyst Blade Switch 3130 for Dell and 3032 for Dell Port Descriptions (continued) Port Internal 100BASE-T Ethernet port Console port StackWise Plus ports Description The internal 100BASE-T Ethernet port (Fa0) is used only for switch management traffic, not for data traffic. It is connected to the Dell management console through the server chassis backplane connector. Traffic to and from this port is isolated from the switch ports. Switch management serial port that uses an RJ-45 connector. Stacking cable ports (supported only on the 3130G-S and 3130X-S switches). Other Features These sections describe other switch features: Switch Console Port, page /100/1000 Ports, page Gigabit Ethernet Module Slots, page 1-4 LEDs, page 1-4 StackWise Plus Ports, page 1-8 Power Connectors, page 1-8 Switch Console Port You can connect the switch through its console port to a PC by using the RJ-45-to-DB9 female cable that ships with the product. If you need a spare cable, you can order a kit (part number ACS-DSBUASYN=) directly from Cisco. If you want to attach the switch to any other device, such as a terminal server, you might need a different cable. For console port and adapter pinout information, see the Connector and Cable Specifications section on page B-1. 10/100/1000 Ports The 10/100/1000 Ethernet ports use standard RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters). The 100BASE-TX and 1000BASE-T traffic requires Category 5, Category 5e, or Category 6 unshielded twisted pair (UTP) cable. If you are configuring the port for 10BASE-T traffic, you can use a Category 3 or Category 4 UTP cable. For more information about the 10/100/1000 Ethernet port connections and specifications, see the Connecting to 10/100/1000 Ethernet Ports, page 2-27, and Appendix B, Connector and Cable Specifications. 1-3

14 Other Features Chapter 1 Product Overview 10-Gigabit Ethernet Module Slots The switch 10-Gigabit Ethernet module slots are used for uplink connections to other switches and routers. The module slots operate in full-duplex mode and use the Cisco TwinGig Converter Module. The CBS 3130X-S uses the hot-swappable Cisco X2 transceiver modules and the Cisco TwinGig Converter Module. The CBS 3130X-S supports these X2 transceiver modules: CX4 LRM SR Cisco TwinGig Converter Module For more information about the 10-Gigabit Ethernet module slots, see the Installing Devices in the 10-Gigabit Ethernet Slots section on page For cable specifications, see Appendix B, Connector and Cable Specifications. The Cisco Catalyst Blade Switch 3032G and 3130G support only the Cisco TwinGig Converter Modules, not the X2 transceiver modules. The Cisco TwinGig Converter Module (model CVR-X2-SFP), also known as the converter module, has two small form-factor pluggable (SFP) module slots that convert the 10-Gigabit slot into a dual SFP module interface to establish Gigabit uplinks to network devices. The SFP modules have LC connectors for fiber-optic connections or RJ-45 connectors for copper connections. These are the supported Cisco SFP modules: 1000BASE-LX/LH SFP (GLC-LH-SM) 1000BASE-SX (GLC-SX-MM) 1000BASE-T SFP (GLC-T) For more information about the Cisco TwinGig Converter Module, see the Installing X2 Transceiver Modules and Cisco Converter Modules section on page 2-22 and the Installing X2 Transceiver Modules and Cisco Converter Modules section on page For cable specifications, see Appendix B, Connector and Cable Specifications. LEDs You can use the switch LEDs to monitor switch activity and performance. The System LEDs are controlled by the Cisco IOS software. The System Status ID/LED is controlled by the Dell software. For graphical representations of the LEDs described in this section, see the device manager GUI. The LEDs are described in these sections: System LED, page 1-5 Stack LED (Only the CBS3130G-S and CBS3130X-S Switches), page 1-5 Stack Master LED (Only the CBS3130G-S and CBS3130X-S Switches), page 1-5 Stack Member LED (Only the CBS3130G-S and CBS3130X-S Switches), page 1-6 RJ-45 Uplink Port LEDs, page 1-6 System Status/ID LED, page

15 Chapter 1 Product Overview Other Features Note The System LED (SYST), stack LED (STCK), Stack Master LED (MSTR), and Stack Member LED (MMBR) are shown as item 9 in Figure 1-1 on page 1-2. System LED The System LED (SYST) shows whether the system is receiving power and is functioning properly. Table 1-2 lists the LED colors and their meanings. Table 1-2 Color Off Blinking green Solid green Amber System LED System Status System is not powered on. POST is in progress. System is operating normally. System is receiving power but is not functioning properly. Stack LED (Only the CBS3130G-S and CBS3130X-S Switches) To see the status of the StackWise Ports, press the Mode button. The stack LED (STCK) is green when the Stackwise Plus ports are up and amber when the ports are down. The 10-Gigabit Ethernet module slot LEDs 23 and 24 show the status for Stackwise Plus ports 1 and 2, respectively (see items 4 and 6 in Figure 1-1 on page 1-2). When in stack mode, if both 10-Gigabit Ethernet uplink port LEDs are green, the stack is operating at full bandwidth. If one or both of the 10-Gigabit uplink LEDs are not green, the stack is not operating at full bandwidth. Stack Master LED (Only the CBS3130G-S and CBS3130X-S Switches) The Stack Master LED (MSTR) shows the stack master status. Table 1-3 lists the LED colors and their meanings. (Only the CBS3130G-S and CBS3130X-S switches.) Table 1-3 Color Off Green Amber Stack Master LED Description Switch is not the stack master. Switch is the stack master or a standalone switch. An error occurred during stack master election or another type of stack error occurred. 1-5

16 Other Features Chapter 1 Product Overview Stack Member LED (Only the CBS3130G-S and CBS3130X-S Switches) The Stack Member LED (MMBR) shows the switch stack membership number, which ranges from 1 to 9. The Stack Member LED blinks a number of times equal to the membership number of the switch, pauses, and then repeats the process until you turn off stack mode. Table 1-4 lists the LED colors and their meanings when stack mode is on. When stack mode is off, the Member LED is off. Table 1-4 Color Off Blinking Green Member LED With Stack Mode On Description Pause between blinking stack membership number. Duration is 5 seconds. After pause, LED blinks green. A total of n on-off cycles with n = switch stack membership number in range 1 to 9. After n on-off cycles, blinking stops, and LED turns off. RJ-45 Uplink Port LEDs The external 10/100/1000BASE-T copper Gigabit Ethernet uplink port LEDs display link and activity information about each individual port. These LEDs are on the top left and bottom left or on the top right and bottom right, respectively, of each RJ-45 port (see item 3 in Figure 1-1 on page 1-2). Table 1-5 describes the port link LED colors and their meanings. Table 1-5 Meaning of Port Link LED Colors LED Color Off Solid green Blinking green Amber Alternating Green/Amber 1. STP: Spanning Tree Protocol. Meaning No link established. Link established, no activity. Traffic on an established link. Port disabled, either error or STP 1 disabled. Link fault. The port activity LED blinks green to indicate traffic. System Status/ID LED The System Status/ID LED is controlled by the server chassis software. See Table 1-6 for descriptions of this LED. Table 1-6 Meaning of System Status ID/LED Colors LED Color Meaning Blue on Switch stack master. Blue off Switch stack member. Blinking amber The CMC 1 and the switch are not communicating properly. 1. CMC = Chassis Management Controller. 1-6

17 Chapter 1 Product Overview Other Features 10-Gigabit Ethernet Module Slot Port LEDs The behavior of the 10-Gigabit Ethernet module slot port LEDs depends on whether an X2 module or a converter module is installed and whether you pressed the Mode button to place the switch module in stack mode. X2 Module Installed (Only the CBS3130X-S Switch) The 10-Gigabit Ethernet module slot LEDs 21 to 22 show the status for ports 21 to 22. The 10-Gigabit Ethernet module slot LEDs and 23 and 24 show the status for ports 23 and 24. (See items 4 and 6 in Figure 1-1 on page 1-2.) When an X2 module is installed, each pair of LEDs behaves as one. LEDs 21 and 22 represent the X2 module in slot 21 to 22. LEDs 23 and 24 represent the X2 module in slot 23 to 24. Table 1-7 describes the 10-Gigabit Ethernet slot port LED colors and their meanings. Table 1-7 Meaning of 10-Gigabit Ethernet Module Slot LED Colors LED Color Off Solid green Blinking green Amber Alternating green/amber Meaning No link established. Link established, no activity. Activity (traffic) on an established link. Port disabled, either error or STP disabled. Link fault. Converter Module Installed LED Behavior in Stack Mode When a converter module is in one of the 10-Gigabit Ethernet module slots, the LEDs show the status of the SFP modules that are in the converter module. If one converter module is installed in slots 21 and 22, and one converter module is installed in slots 23 and 24, this is how the LEDs correspond to the installed SFP modules: 1. LED 21 corresponds to the SFP module in the top slot. 2. LED 22 corresponds to the SFP module in bottom slot. 3. LED 23 corresponds to the SFP module in the top slot. 4. LED 24 corresponds to the SFP module in bottom slot. See Table 1-7 for a description of the 10-Gigabit Ethernet slot port LED colors and their meanings. Whether an X2 module or a converter module is installed in the 10-Gigabit Ethernet module slots, the LEDs 23 and 24 show the status of the StackWise Plus ports 1 and 2, respectively. LEDs 21 and 22 are off when in stack mode. Table 1-8 describes the LED colors in stack mode and their meanings. Table 1-8 LED Color Solid green Amber Meaning of LEDs 22 and 24 Colors in Stack Mode Meaning Stack port is connected. If both LEDs are green, the stack is running at full speed. Stack port is not connected. 1-7

18 Management Options Chapter 1 Product Overview StackWise Plus Ports The stacking-capable switches ship with a 1-meter Stackwise Plus cable that you can use to connect the Stackwise Plus ports. Caution Use only approved cables, and connect only to similar Cisco equipment. Equipment might be damaged if connected to nonapproved Cisco cables or equipment. You can order these StackWise Plus cables from your sales representative: CAB-STK-E-0.5M= (0.5-meter cable) CAB-STK-E-1M= (1-meter cable) CAB-STK-E-3M= (3-meter cable) Power Connectors The blade server chassis controls power to the switch. After the blade server software detects the presence of the switch, it moves the switch to the full power state. The switch software is not involved in power control functions. Management Options This section describes management options for the switch: Using the Device Manager, page 1-8 Using the Dell CMC, page 1-9 Using the Command-Line Interface, page 1-9 Other Management Options, page 1-10 Using the Device Manager The simplest way to manage the switch is by using the device manager that is in the switch memory. This is a web interface that offers quick configuration and monitoring. You can access the device manager from anywhere in your network through a web browser. Follow these steps: 1. Launch a web browser on your PC or workstation. 2. Enter the switch IP address in the web browser, and press Enter. The device manager page appears. (See Figure 1-2.) 1-8

19 Chapter 1 Product Overview Management Options Figure 1-2 Device Manager Page 3. Use the device manager to perform basic switch configuration and monitoring. Refer to the device manager online help for more information. 4. For more advanced configuration, download and run the Cisco Network Assistant, which is described in the next section. Using the Command-Line Interface The switch command-line interface (CLI) is based on Cisco IOS software and enhanced to support desktop-switching features. You can fully configure and monitor the switch from the CLI. You can access the CLI either by connecting your management station directly to the switch console port or by using Telnet from a remote management station. Refer to the switch command reference on Cisco.com for more information. Using the Dell CMC See the Dell documentation for information about using the CMC. 1-9

20 Network Configurations Chapter 1 Product Overview Other Management Options You can use SNMP management applications such as CiscoWorks Small Network Management Solution (SNMS) to configure and manage the switch. You also can manage it from an SNMP-compatible workstation that is running platforms such as HP OpenView or SunNet Manager. Network Configurations Refer to the switch software configuration guide on Cisco.com for an explanation of network configuration concepts. The software configuration guide also provides examples of network configurations that use the switch to create dedicated network segments that are interconnected through Gigabit Ethernet connections. 1-10

21 CHAPTER 2 Switch Installation This chapter provides instructions on how to install your Cisco Catalyst Blade Switch 3130 for Dell and the Cisco Catalyst Blade Switch 3032 for Dell, referred to as the switch. The switch modules are installed in the Dell Modular Server Chassis, referred to as the server chassis, a system that supports up to sixteen server modules and up to six Ethernet switches. You install the switch in one of the chassis I/O module bays on the rear panel of the server chassis. This chapter also describes how to interpret the power-on self-test (POST) that ensures proper operation and how to make connections to the switch module. Read the topics and perform the procedures in this order: Safety Warnings, page 2-1 Dell Modular Server Chassis Architecture, page 2-3 Installing the Switch in the Server Chassis, page 2-4 Configuring the Switch, page 2-7 Managing the Switch, page 2-15 Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S Switches), page 2-17 Installing Devices in the 10-Gigabit Ethernet Slots, page 2-21 Connecting to 10/100/1000 Ethernet Ports, page 2-27 Where to Go Next, page 2-27 Safety Warnings These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for Dell that ships with the product. The EMC regulatory statements are also included in that guide. Warning To prevent the switch from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 104 F (40 C). To prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around the ventilation openings. Statement 17B 2-1

22 Safety Warnings Chapter 2 Switch Installation Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43 Warning Ethernet cables must be shielded when used in a central office environment. Statement 171 Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning Class 1 laser product. Statement 1008 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. 10/100/1000 Ethernet Statement 1044 Warning Installation of the equipment must comply with local and national electrical codes. Statement

23 !!!! WS-CBS3130X-S R S R K!!!!!!! Chapter 2 Switch Installation Dell Modular Server Chassis Architecture Dell Modular Server Chassis Architecture The six chassis I/O module bays are on the rear panel (see Figure 2-1). Figure 2-1 Dell Modular Server Chassis Rear Panel STK B A 18X 17X 20X 19X X X2-2 M MB M ST S TC Y ST! MODE CONSOLE!!!!!! Dell server chassis 7 I/O module bay C2 2 Primary CMC 1 module 8 I/O module bay B2 3 Switch installed in I/O module bay A1 9 I/O module bay A2 4 I/O module bay B1 10 Secondary CMC module 2 5 I/O module bay C1 11 Fan modules 6 Optional ikvm 3 module 12 Power supplies 1. CMC: Chassis Management Controller. 2. This module is optional. 3. ikvm: integrated keyboard video mouse. 2-3

24 Installing the Switch in the Server Chassis Chapter 2 Switch Installation Installing the Switch in the Server Chassis See the getting started guide that ships on CD-ROM with the product for information about what ships with your switch. Before you install the switch in the server chassis, consider these points: Review and become familiar with the safety and handling guidelines specified in the Product Information Guide. Review the Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for Dell that ships with this product. If you plan to create a switch stack, review the Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S Switches) section on page 2-17 before you install the switch and run the initial configuration setup program. To help ensure proper cooling and system reliability, keep these points in mind: Each chassis I/O module bay must contain either a module or an input/output module (IOM) blank. Fan modules must be operating in the fan module bays to ensure proper cooling of the switch modules. See the Dell server chassis documentation for information about how to ensure that the modules are properly cooled. When you remove a hot-swap module, you must replace it with an identical module or an IOM blank within 1 minute of removal. You can install the switch into any of the module bays. If you install a switch in the B or C module bay, the Ethernet mezzanine cards must be installed in the blade server. The dust covers should always remain in place unless a module is installed in the slot. Caution To prevent electrostatic-discharge (ESD) damage when you install the switch, follow your normal board and component handling procedures. When you install a switch, you do not need to power down the server chassis. Be sure to observe these requirements: For copper Ethernet ports, cable lengths from the switch module to connected devices can be up to 328 feet (100 meters). See the documentation for the SFP module for more information about cable specifications for the SFP module connections. Also see the SFP Module Cable Specifications section on page B-6. Each port must match the wave-length specifications on the other end of the cable, and the cable must not exceed the stipulated cable length for reliable communications. When you use shorter lengths of single-mode fiber-optic cable, you might need to insert an inline optical attenuator in the link to avoid overloading the receiver. Operating environment is within the ranges listed in Appendix A, Technical Specifications. Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting fixtures. Make sure the cabling is safely away from other devices that might damage the cables. 2-4

25 Chapter 2 Switch Installation Installing the Switch in the Server Chassis Follow these steps to install the switch into the server chassis: Step 1 Step 2 Step 3 Step 4 Step 5 Obtain and make note of this information from your network administrator before you begin the switch installation: Switch IP address Subnet mask (IP netmask) Default gateway (router) Enable secret password (encrypted) Enable password (not encrypted) Telnet password SNMP community strings (optional) Select a chassis I/O module bay in which to install the switch. Follow the prerequisites listed in the Dell Modular Server Chassis Architecture section on page 2-3. Remove the IOM blank from the selected bay, and store it for future use. If you have not already done so, touch the static-protective package that contains the switch to an unpainted metal part of the server chassis for at least 2 seconds. Remove the switch from its static-protective package. 2-5

26 WS-CBS3130X-S Installing the Switch in the Server Chassis Chapter 2 Switch Installation Step 6 Ensure that the release latch on the switch is in the open position or perpendicular to the module (see Figure 2-2): Figure 2-2 Release Latch in Open Position STK B A 18X 17X 20X X2-1 19X X2-2 M M M ST BR R S TC K S Y S T MODE CONSOLE Step 7 Step 8 Slide the switch into the appropriate bay until it stops. Push the release latch on the front of the switch to the closed position. 2-6

27 ! R R K T CONSOLE!!!!!!!!!! Chapter 2 Switch Installation Configuring the Switch Figure 2-3 shows the switch being inserted into the server chassis. Figure 2-3 Inserting the Switch into the Server Chassis X STK B A 17X 20X 19X X X2-2 3 WS-CBS3130X-S M MB M ST S TC S YS MODE!!!!!! Switch 3 Release latch 2 Server chassis Configuring the Switch To run the system configuration dialog, you must first connect the switch to a PC to run a terminal emulation program. You can connect the switch to the PC either through the switch console port or through the CMC console port. Instructions for these procedures are included in this section. If you connect to the switch through the CMC, the switch console port is disabled. After you have completed the configuration procedure, you must use the disconnect command to close the active console port and re-enable the switch console port. Enter logout to log out of the switch, then enter Ctrl \ to disconnect the CMC from the switch. 2-7

28 !! WS-CBS3130X-S M M S S M STR TCK YST BR CONSOLE Configuring the Switch Chapter 2 Switch Installation Follow one of these procedures: To run the terminal emulation program through the switch console port, go to Connecting through the Switch Console Port section on page 2-8. To run the terminal emulation program through the CMC port, go to Connecting through the CMC section on page 2-9. Connecting through the Switch Console Port Follow these steps when connecting through the switch console port: Step 1 Connect one end of the console cable to the switch console port. Connect the other end of the cable to the serial port of the PC that is running the terminal emulation application. (See Figure 2-4.) Figure 2-4 Connecting To the Switch Console Port MODE!! Step 2 Step 3 Start the terminal emulation session so that you can see the output display from the power-on self-test (POST). The terminal-emulation software a PC application such as Hyperterminal or ProcommPlus makes communication between the switch and your PC or terminal possible. Configure the baud rate and character format of the PC or terminal to match these console port default characteristics: 9600 baud 8 data bits 1 stop bit No parity None (flow control) Go to the Waiting for POST to Complete section on page 2-10 to finish configuring the switch. 2-8

29 Chapter 2 Switch Installation Configuring the Switch Connecting through the CMC Follow these steps when connecting through the CMC: Step 1 Step 2 Step 3 Connect one end of a DB-9 null-modem or crossover cable to the RS-232 console serial port of the CMC. Connect the other end of the cable to the RS-232 console serial port of the PC. On the PC terminal emulation program: a. Set the data format to 8 data bits, 1 stop bit, and no parity. b. Set the terminal emulation speed to baud. c. Set Flow Control to none. d. Under Properties, select VT100 for Emulation mode. e. Select Terminal keys for Function, Arrow, and Ctrl keys. Ensure that the setting is for Terminal keys (not Windows keys). When using HyperTerminal with Microsoft Windows 2000, ensure that you have Windows 2000 Service Pack 2 or later installed. With Windows 2000 Service Pack 2, the arrow keys function properly in the HyperTerminal VT100 emulation. Go to for information on Windows 2000 service packs. On the console monitor, the CMC application displays a login screen. Log in by using these defaults: username root password calvin The CMC command-line interface (CLI) command prompt CMC: appears. Note If the server chassis is off, use this command to power it on: racadm chassisaction -m chassis powerup The switch inserted into the chassis I/O bay automatically powers on when the server chassis powers on. For more information on configuring the server chassis by using the CLI, see the Dell Remote Access Controller/Modular Chassis User's Guide. Power-cycle the switch by using this command: racadm chassisaction -m switch-n powercycle where N is the chassis I/O module bay number in which the switch is inserted. Module Bay A1 1 A2 2 B1 3 B2 4 C1 5 C2 6 Substitute for N 2-9

30 Configuring the Switch Chapter 2 Switch Installation Step 4 Step 5 Redirect the CMC console to the switch internal serial console interface. Enter this command at the CMC command prompt: connect switch-n where N is the chassis I/O module bay number in which the switch is inserted. To return to the command prompt, press this key sequence: Enter Ctrl \ (Press Enter, and press the Control key and the backslash key together.) Go to the Waiting for POST to Complete section on page 2-10 to finish configuring the switch. Waiting for POST to Complete Follow these steps to verify that POST completes successfully: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Wait for the switch to complete the POST. During POST, the LEDs blink while tests verify that the switch functions properly. Wait for the switch to complete POST, which can take several minutes. Verify that POST has completed by confirming that the SYST LED remains green. If the switch fails POST, the SYST LED turns amber. See Figure 1-1 on page 1-2 for the location of the SYST LED. POST errors are usually fatal. Call Cisco Customer Support immediately if your switch fails POST. Wait for the switch to complete flash initialization. When you see the prompt Press Return to Get Started!, press Return or Enter. If you do not see the prompt Press Return to Get Started!, be sure that you have set the baud rate on the terminal to 9600 baud. Make sure that the System Status/ID LED on the switch is off. This means that the switch is operating properly. See the Completing the Initial Configuration section on page 2-10 for instructions on setting up and initially configuring the switch. If the switch obtains an IP address through the Fa0 port, you can use the device manager to configure the switch. See the Using the Device Manager to Configure the Switch section on page Completing the Initial Configuration Follow these steps to complete the setup program and to create an initial configuration for the switch. For information about automatically configuring the switch, see the Assigning the Switch IP Address and Default Gateway chapter in the switch configuration guide on Cisco.com. Step 1 After you have pressed Enter or Return after the prompt to start the initial configuration setup program, enter yes at these prompts: Would you like to terminate autoinstall? [yes]: yes --- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: yes 2-10

31 Chapter 2 Switch Installation Configuring the Switch At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Configuring global parameters: Step 2 Step 3 Step 4 Step 5 Step 6 Enter a hostname for the switch after the prompt, and press Return. The hostname is limited to 20 characters. Do not use -n, where n is a number, as the last character in a host name for any switch. Enter an enable secret password, and press Return. The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is in plain text. Enter an enable password, and press Return. Enter a virtual terminal (Telnet) password, and press Return. The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores leading spaces. (Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. 1. To configure SNMP later, press Return (which applies the default of no). If you accept the default, you can configure SNMP later through the CLI. Configure SNMP Network Management? [no]: 2. To configure SNMP now, enter yes. Configure SNMP Network Management? [no]: yes Community string [public]: public Step 7 Step 8 Step 9 Enter the interface name (physical interface or VLAN name) of the interface that connects to the management network, and press Return. Enter vlan1 for the interface name at this prompt. To configure the interface, enter Yes after the prompt, and then enter the switch IP address and subnet mask. Press Return. The IP address and subnet mask shown here are examples: Configuring interface Vlan1: Configure IP on this interface? [yes]: IP address for this interface [ ]: Subnet mask for this interface [ ] : Class A network is , 21 subnet bits; mask is /21 Enter no when the prompt asks you if you would like to enable the switch as a cluster command switch. This switch will be a standalone switch. Would you like to enable as a cluster command switch? [yes/no]: no Note Clustering is not supported. 2-11

32 Configuring the Switch Chapter 2 Switch Installation You have now completed the initial configuration of the switch, and the switch displays its initial configuration. An example of the output is shown here: The following configuration command script was created: hostname switch1 enable secret 5 $1$cagJ$e4LP91PNazfdADoNAZm6y0 enable password enable_password line vty 0 15 password terminal-password snmp-server community public!! interface Vlan1 no shutdown ip address ! interface FastEthernet0 shutdown no ip address! interface GigabitEthernet1/0/1! interface GigabitEthernet1/0/2!... (output truncated)! interface TenGigabitEthernet1/0/1! interface TenGigabitEthernet1/0/2! end Step 10 These choices appear: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. If you want to save the configuration and use it the next time the switch reboots, save it in NVRAM by selecting option 2. Enter your selection [2]:2 Step 11 Make your selection, and press Return. Disconnect the server chassis serial port or the switch console port from the PC. See the Managing the Switch section on page 2-15 for information about configuring and managing the switch. 2-12

33 Chapter 2 Switch Installation Configuring the Switch Using the Device Manager to Configure the Switch Follow these steps to set up the switch through the device manager. In a browser window, enter the IP address that the Fa0 port assigned to the switch. Before you complete the setup program, obtain the default gateway IP address and the switch password from your system administrator. You can configure these optional parameters through the Express Setup program: Telnet access password Names of the SNMP read and write community strings if you are going to use a network-management program like CiscoWorks Host name, system contact, and system location System time, time zone, Daylight Savings Time enable Step 1 On the left side of the device manager GUI, choose Configuration > Express Setup. The Express Setup page appears (see Figure 2-5 and Figure 2-6). (Close or minimize the device manager Help window.) Figure 2-5 Express Setup Page Step 2 Enter this information in the Network Settings fields. In the Default Gateway field, enter the IP address for the default gateway (router). In the Switch Password field, enter your password. The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows embedded spaces, but does not allow spaces at the beginning or end. In the Confirm Switch Password field, enter your password again. 2-13

34 Configuring the Switch Chapter 2 Switch Installation You can enter the Optional Settings information now or enter it later by using the device manager interface. Figure 2-6 Advanced Settings Tab Step 3 Step 4 Step 5 Step 6 Step 7 In the Host Name field, enter a name for the switch module. The host name is limited to 31 characters; embedded spaces are not allowed. In the System Date and System Time fields, enter the current date and time, or use the down arrows to select them. In the Time Zone field, use the down arrow to choose your time zone. Click Enable in the Daylight Savings Time field to enable this feature. In the Telnet Access field, click Enable if you are going to use Telnet to manage the switch module by using the CLI. If you enable Telnet access, you must enter a Telnet password. Note If you plan to create a switch stack, enable Telnet access so that you can use the CLI to set this switch to the highest priority (usually 15). See the Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S Switches) section on page 2-17 for more information about creating a switch stack. Step 8 Step 9 Step 10 In the Telnet Password field, enter a password. The Telnet password can be from 1 to 25 alphanumeric characters, is case sensitive, allows embedded spaces, but does not allow spaces at the beginning or end. In the Confirm Telnet Password field, re-enter the Telnet password. In the SNMP field, click Enable to enable Simple Network Management Protocol (SNMP). Enable SNMP only if you plan to manage switches by using CiscoWorks 2000 or another SNMP-based network-management system. If you enable SNMP, you must enter a community string in the SNMP Read Community field, the SNMP Write Community field, or both. SNMP community strings authenticate access to MIB objects. Embedded spaces are not allowed in SNMP community strings. When you set the SNMP read community, you can access SNMP information, but you cannot change it. When you set the SNMP write community, you can both access and change SNMP information. 2-14

35 Chapter 2 Switch Installation Managing the Switch Step 11 Step 12 Step 13 In the System Contact field, enter the name of the person who is responsible for the switch module. In the System Location field, enter the wiring closet, floor, or building where the switch module is located. Depending on which software license you choose, you can enable IPv6 in the IPv6 Settings area. Click Enable IPv6 to enable it. In the Interface column, choose the interface for which you want to set an IPv6 address, and complete the other fields in this table. Click Submit to save your settings, or click Cancel to clear your settings. You can close this window. Configuring the Switch Stack Master If you plan to create a switch stack, we recommend that you set the first configured switch as the stack master. To do this, you must assign the highest priority value to that switch. To assign a priority value after you have installed and initially configured the first switch, follow these steps: Step 1 Launch a Telnet session. Step 2 Enter enable. Step 3 Enter configure terminal. Step 4 Enter switch 1 priority 15. Step 5 At the prompt, press Return. Step 6 Enter end to exit this mode. Step 7 Enter copy running-configuration startup-configuration to save this setting. Step 8 At the prompt, press Return. Step 9 To verify that this switch is set as the master, enter the show switch user EXEC command. For more information about creating switch stacks, see the Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S Switches) section on page Managing the Switch After completing the initial setup and configuration steps, use the CLI, the device manager, or other management options described in this section for further configuration. Using the CLI After setting up and installing the switch in your network, you can enter Cisco IOS commands and parameters through the CLI. Access the CLI either by connecting your PC directly to the switch console port or through a Telnet session from a remote PC or workstation. You can also access the CLI through the server chassis serial console port of the active Dell CMC. For more information, see the hardware installation guide on Cisco.com. 2-15

36 Managing the Switch Chapter 2 Switch Installation Using the Device Manager The simplest way to manage the switch is by using the device manager that is in the switch memory. This is an easy-to-use web interface that offers quick configuration and monitoring. You can access the device manager from anywhere in your network through a web browser. The device manager dashboard is shown in Figure 2-7. Figure 2-7 Device Manager Dashboard Follow these steps to access the device manager: Step 1 Step 2 Step 3 Launch a web browser on your PC or workstation. Enter the switch IP address in the web browser, and press Enter. The device manager page appears. Use the device manager to perform basic switch configuration and monitoring. See the device manager online help for more information. Other Management Options You can use SNMP management applications such as CiscoWorks. You also can manage it from an SNMP-compatible workstation that is running platforms such as SunNet Manager. 2-16