How to Configure Cisco UC500 Series (Basic Configuration)
|
|
- Arabella Harris
- 6 years ago
- Views:
Transcription
1 How to Configure Cisco UC500 Series (Basic Configuration) Cisco Unified Communication Manager 500 Series can be configured using Cisco Configuration Assistance which comes in CD with UC500 or can be downloaded from Cisco Official Site. Follow the following setups to configure UC500: 1. Connect Ethernet cable from any of 8 IP Phone ports to your laptop or machine ethernet adapter. 2. Set IP configuration of adapter to Obtain IP from DHCP (as DHCP is enabled by default for IP Phone Ports). 3. It will obtain IP in network of x, as shown below: 4. Now start Cisco Configuration Assistant (CCA). 5. Connect to UC500 using IP Address: (which is your gateway).
2 6. Now before you connect to UC500, you need to enter username and password. So to create username and password you have to connect to console via Serial Cable and via Hyper Terminal enter following command in global configuration mode (entered via entering command configure terminal): username admin password cisco Now login into UC500 with the credentials created in above command: a. Username: admin b. Password: cisco c. Privilege Level: You will come up with Telephony Setup Wizard. Close this wizard as we will setup manually. 9. Now we have to configure exchange, on left panel, go to: Telephony Users and Extensions Users and Phones.
3 10. Now when you click Users and Phones, and dialog appears like shown below which ask you for Telephony Initialization. 11. As per your wish you can enter Number of Digits Per Extension and Voic Access Extension. (I have entered 3 Digits per Extension and 200 as Voic Access Extension). 12. At this point, you exchange is ready to connect IP phones. 13. Now connect IP Phone to one of the IP Phone Port at front panel of UC If you don t have IP Phone and want to configure using some software which acts as IP Phone, you can use Cisco IP Communicator (CIPC) Software. All the configuration show ahead is using Cisco IP Communicator as IP Phone.
4 15. Install Cisco IP Communicator (CIPC) on your laptop and other machines you want to make call. When you install CIPC, you can see Cisco Discovery Protocol (CDP) Packet Driver installed in your ethernet adapter settings. (IP Phones use CDP protocol to discover other voice devices) 16. When you start CIPC, your phone will automatically discover UC500 in network using CDP and register itself to it. 17. When phone registers itself with exchange, exchange displays messages on terminal as shows below:
5 18. At this moment, phone is registered to exchange, but to make it working you have to configure phone with extension number and some other configurations. To configure phone, navigate to Users and Phone in Cisco Configuration Assistant (CCA). 19. There you will see this phone in list but un-configured. Select this phone and click on Edit. 20. In edit mode enter the required information for this phone. I have entered information as shown below:
6 21. After entering the required information click OK. Extension Number entered above 201 is the phone number for this phone. 22. When configured successfully, it will show full information in Users and Phone list as shown below: 23. At this moment phone is ready for use with extension number On IP phone you can see the changes, it will now show its extension number and description of the phone configured in CCA as shown below:
7 25. In similar manner you can configure another IP Phone or CIPC for testing purpose. I am attaching few screenshots of second CIPC phone configurations.
8
9 26. At this moment, both phones are ready to make call. So make a test call between these two phones. Make a call from phone DSharma 202 to Sakun 201.
10 27. You can see topology by clicking Topology and see exchange topology as shown below: 28. Now save configuration by navigating to Save Configuration, last option in CCA left panel and save configuration for all devices.
11
UC320 Lab 1: Initial UC320 Configuration
UC320 Lab 1: Initial UC320 Configuration Task 1: Gathering Pod Equipment and Initial Configuration NOTE Do NOT cable everything at this point. Connect your PC to Port 4 on the UC320 and connect the UC320
More informationHow to assign an IP address and access your device
User Manual Table of Contents Get started................................................ 3 Browser support................................................ 3 About default IP addresses........................................
More informationCisco Voice Services Self-Care Portal User Guide
Cisco Voice Services Self-Care Portal User Guide OVERVIEW What Is It? The Self Care Portal can be used to manage your telephone settings, including changing and updating settings without contacting the
More information4. Web-based Switch Configuration
4. Web-based Switch Configuration Management Options Connecting using the Web User Interface Logging onto the Web Manager Smart Wizard Web User Interface (Web UI) Management Options The Switch provides
More informationHow to assign an IP address and access your device
User Manual Table of Contents Get started................................................ 3 Browser support................................................ 3 About default IP addresses........................................
More informationUnderstanding UCS Server Configuration Utility User Interface
CHAPTER 3 Understanding UCS Server Configuration Utility User Interface The UCS-SCU GUI is a web-based management interface that allows you to perform tasks such as operating system installation, RAID
More informationConfiguring Microsoft Outlook to Connect to Hosted Exchange Service
Configuring Microsoft Outlook to Connect to Hosted Exchange Service Configuring Microsoft Outlook for Hosted Exchange Service Version: 1.0 Updated on: April 27, 2011 Page 1 of 7 TABLE OF CONTENTS Configuring
More informationNETWORK LAB 2 Configuring Switch Desktop
Configuring Switch 1. Select the switch tab and then add a switch from the list of switches we have to the workspace, we will choose (2950-24) switch. 2. Add a number of PCs next to the switch in order
More informationGnostice StarDocs On-Premises API Virtual Appliance
Gnostice StarDocs On-Premises API Virtual Appliance Deployment Instructions For VMware vsphere 2 For Oracle VirtualBox 4 For VMware Fusion (on Mac OS) 6 For VMware vsphere Note that the instructions below
More informationPlease note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system.
Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system. Please follow these steps to ensure that any changes made by your previous
More informationPrint Server Setup Guide (NF1ADV)
Print Server Setup Guide (NF1ADV) Print Server Setup for the NF1ADV This set of print server setup instructions is intended for use with printers connecting with a USB cable connection being plugged into
More informationInstalling Cisco StadiumVision Director Software from a DVD
Installing Cisco StadiumVision Director Software from a DVD First Published: May 29, 2012 Revised: August 2, 2012 This module describes how to install the Cisco StadiumVision Director Release 3.0 software
More informationGetting Started with the VG248
CHAPTER 2 Before you can configure the telephony features on the VG248 to interact with the analog phones, you must first configure the basic network, SNMP, and password settings. These settings enable
More informationCassia E1000/X1000/C1000 Quick Start Guide
Cassia E1000/X1000/C1000 Quick Start Guide Step One Connect your laptop/pc to your Bluetooth router Check your Bluetooth router s MAC address on the bottom of the router, as noted in Figure 1 below. Then
More informationCisco. Small Business SBCS Technical Enablement Lab (TEL) UC500 SWP Upgrade with CCA 3.0
Cisco Small Business SBCS Technical Enablement Lab (TEL) UC500 SWP 8.1.0 Upgrade with CCA 3.0 Contents Introduction... 3 SW Upgrade... 4 2 Introduction Before you begin, you must download the necessary
More informationInstalling Authoring Manager
Installing Authoring Manager Installing Authoring Manager v5.2 (PC only) System Requirements: Before you install Authoring Manager, you should ensure that your system meets the minimum software and hardware
More informationPlus-X I/O Units. Manual Supplement Configuring Units with and without DHCP
Plus-X I/O Units Manual Supplement Configuring Units with and without DHCP Table of Contents Introduction... 1 Initial Connection Using DHCP... 1 Initial Connection Without DHCP... 2 Set a Static IP Address...
More information802.11g Super-G 108Mb Wireless Access Point Quick Installation Guide
802.11g Super-G 108Mb Wireless Access Point Quick Installation Guide The enclosed Hardware Installation Guide gives you a step-by-step explanation of how to install your 108Mb Super-G PCI Adapter. Further
More informationMeridian 6.4. Quick Configuration Guide DVTEL INC. 65 Challenger Road. Ridgefield Park, NJ 07660
DVTEL INC. 65 Challenger Road Ridgefield Park, NJ 07660 Meridian 6.4 Quick Configuration Guide The contents of this Guide may not be reproduced or reprinted in whole or in part without the express written
More information6.1. Getting Started Guide
6.1 Getting Started Guide Netmon Getting Started Guide 2 Contents Contents... 2 Appliance Installation... 3 IP Address Assignment (Optional)... 3 Logging In For the First Time... 5 Initial Setup... 6 License
More informationChecklists for Configuring the Gateway
CHAPTER 7 The Cisco Unified Communications Manager Business Edition 3000 uses either Cisco 2901 Integrated Services Router (ISR2901) or Cisco Media Convergence Server 7890C1 (MCS7890-C1) to serve as your
More informationBusiness Internet Video Camera with Audio
Business Internet Video Camera with Audio Quick Install Guide Package Contents WVC210 Camera Stand Power Supply (5V 2A) 6 Ethernet Cable Setup CD Antenna Quick Install Guide BUSINESS SERIES Model: WVC210
More informationDSL-504T ADSL Router. CD-ROM (containing User Manual) Ethernet Cable (CAT5 UTP) ADSL Cable (For AUS 200CM) Power Adapter
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DSL-504T ADSL Router Before You Begin 1. If you purchased this Router to share your high-speed
More informationFLX UC 1000/1500 Registering with Shoretel ShoreGear
Technical Note FLX UC 1000/1500 Registering with Shoretel ShoreGear Date: January 15, 2016 This technical note gives a detailed description on how to register a Revolabs FLX UC 1000/1500 IP & USB conference
More informationGetting Started with Your Device Configuration
Quick Setup Tasks, page 1 Quick Setup Tasks On the first day with your new device, you can perform a number of tasks to ensure that your device is online, reachable and easily configured. The Day 0 wizard
More informationIf you re not using Microsoft Hyper-V 2012, your screens may vary.
If you re not using Microsoft Hyper-V 2012, your screens may vary. VELOCITY REPLICATION ACCELERATOR Microsoft Hyper-V Hypervisor Server Mode (Single-Interface Deployment) 2013 Silver Peak Systems, Inc.
More informationIntegration Configuration
Integration Configuration Configure LDAP with the Configuration Tool, page 1 Configure Voicemail Settings with the Configuration Tool, page 5 Configure Phone Control and Presence with the Configuration
More informationCisco Integrated Management Controller (IMC) Supervisor is a management system that allows you to manage rack mount servers on a large scale.
Contents Introduction Prerequisites Requirements Qualified Serviers Minimum Firmware Versions Supported PCiE Cards Supported Hypervisor versions Supported Browser Versions Configure Deploying Cisco IMC
More informationUnified CCX Administration Web Interface
The Unified CCX provides a multimedia (voice, data, and web) IP-enabled customer-care application environment, using VoIP technology that allows your Cisco Unified Communications network to share resources
More informationStarWind Native SAN for Hyper-V:
This document refers to the previous StarWind Virtual SAN version. To view the document for the current version, please follow this link StarWind Native SAN for Hyper-V: Configuring HA Storage for Live
More informationInstall and Configure FindIT Network Manager and FindIT Network Probe on Microsoft Hyper-V Manager
Install and Configure FindIT Network Manager and FindIT Network Probe on Microsoft Hyper-V Manager Objective The Cisco FindIT Network Management provides tools that help you easily monitor, manage, and
More informationDVG-2001S VoIP Terminal Adapter
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVG-2001S VoIP Terminal Adapter Before You Begin 1. If you purchased this VoIP Terminal
More informationConfiguring a BELKIN Router. Basic Configuration Steps
Configuring a BELKIN Router Basic Configuration Steps Configuring Your Router STEP 1 (a): Connect Your PC to the Router Unbox the router and power up the router. Connect the Act internet cable to the WAN/Internet
More informationSPA400 Internet Telephony Gateway with 4 FXO Ports
SPA400 Internet Telephony Gateway with 4 FXO Ports Administration and Configuration Guide v1.0 Using the SPA400 The SPA400 features the ability to connect up to four (4) standard analog telephones lines
More informationDeploying Cisco UCS Central
This chapter includes the following sections: Obtaining the Cisco UCS Central Software from Cisco, page 1 Using the Cisco UCS Central OVA File, page 2 Using the Cisco UCS Central ISO File, page 4 Logging
More informationConfiguring Cisco Mobility Express controller
There are multiple ways one can configure a Cisco Mobility Express controller. They are as follows: 1 CLI Setup Wizard 2 Over the Air Setup Wizard 3 Network Plug and Play CLI Setup Wizard, page 1 Over-the-Air
More informationEasy Setup Guide. Cisco FindIT Network Probe. You can easily set up your FindIT Network Probe in this step-by-step guide.
Cisco FindIT Network Probe Easy Setup Guide You can easily set up your FindIT Network Probe in this step-by-step guide. 1 5 System Requirements Installing Probe Configuring Probe Using Probe Connecting
More informationValley Library Consortium
On December 13, 2018 the Valley Library Consortium will be upgrading to Horizon 7.5.5. The system will be down from 6:00 AM until the upgrade process is finished. All Horizon staff clients will need to
More informationQuick Start Guide for Standalone EAP
Quick Start Guide for Standalone EAP CHAPTERS 1. Determine the Management Method 2. Build the Network Topology 3. Log In to the EAP 4. Edit the SSID 5. Configure and Manage the EAP This guide applies to:
More informationNF3ADV VoIP Setup Guide (for Dodo)
NF3ADV VoIP Setup Guide (for Dodo) Configuring your NF3ADV for Dodo VoIP The following steps will take you through the process of setting up your VoIP connection. This guide assumes that the NF3ADV already
More informationTechnical Note FLX UC 1000/1500 Registering with Shoretel ShoreGear
FLX UC 1000/1500 Registering with Shoretel ShoreGear Date: February 14, 2017 This technical note gives a detailed description on how to register a Revolabs FLX UC 1000/1500 IP & USB conference phone with
More informationDownloading and Managing Firmware in Cisco UCS Central
Downloading and Managing Firmware in Cisco UCS Central This chapter includes the following sections: Downloading Firmware from Cisco.com, page 1 Firmware Library of Images, page 2 Configuring Firmware
More informationDiscovering Network Devices
CHAPTER 5 To generate reports, Prime Performance Manager must discover your network devices. This is accomplished by importing the device inventory from Cisco Prime Network, running device discovery from
More informationLab 3.4.6a Configure the PIX Security Appliance using Setup Mode and ASDM Startup Wizard
Lab 3.4.6a Configure the PIX Security Appliance using Setup Mode and ASDM Startup Wizard Objective Scenario Topology In this lab exercise, the students will complete the following tasks: Verify that the
More informationCisco Small Business Pro Smart Business Communication System Technical Enablement Labs
Cisco Small Business Pro Smart Business Communication System Technical Enablement Labs Lab 16 SPA525G Video Monitoring of xvc2300 IP Cameras Introduction...3 Prerequisites...3 SPA525G Phone version...3
More informationSIP Speaker and Cisco Call Manager Server Setup Guide
The IP Endpoint Company SIP Speaker and Cisco Call Manager Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-201 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram
More information4G Camera Solution. 4G WiFi M2M Router NTC-140W Security Camera ACTi B97
4G Camera Solution 4G WiFi M2M Router NTC-140W Security Camera ACTi B97 Introduction The NetComm Wireless 4G Camera Solution has been developed to improve productivity and increase profitability of system
More informationInstallation. Power on and initial setup. Before You Begin. Procedure
Power on and initial setup, page 1 Customize ESXi host for remote access, page 4 Access and configure ESXi host, page 6 Deploy virtual machines, page 13 Install applications on virtual machines, page 14
More informationIntegration Configuration
Configure LDAP with the Configuration Tool, page 1 Configure Voicemail Settings with the Configuration Tool, page 4 Configure Phone Control and Presence with the Configuration Tool, page 5 Credential Synchronization,
More informationCisco IP Phone Configuration Guide
Version 1.0 Date: 2016.09.21 Yeastar Information Technology Co. Ltd. Introduction This guide introduces how to configure Cisco IP phones with Yeastar S-Series VoIP PBX. You have multiple ways to configure
More informationConfiguring the CSS for Device Management
CHAPTER 2 Configuring the CSS for Device Management Before you can use the WebNS Device Management user interface software, you need to perform the tasks described in the following sections: WebNS Device
More informationRetake - Skills Assessment Student Training (Answer Key)
Retake - Skills Assessment Student Training (Answer Key) Name:. Topology Assessment Objectives Part 1: Develop the IPv4 Address Scheme (15 points, 0 minutes) Part 2: Configure Device IPv4 and Security
More informationConfiguring Cisco Unity and Unity Connection Servers
CHAPTER 6 Configuring Cisco Unity and Unity Connection Servers Cisco Unity Servers Cisco Unity receives calls, plays greetings, and records and encodes voicemail. When a voicemail is received, Cisco Unity
More informationOverview of Cisco Prime Collaboration Assurance
Overview of Cisco Prime Collaboration Assurance Cisco Prime Collaboration is a comprehensive video and voice service assurance and management system with a set of monitoring, troubleshooting, and reporting
More informationECDS MDE 100XVB Installation Guide on ISR G2 UCS-E and VMWare vsphere Hypervisor (ESXi)
ECDS MDE 100XVB Installation Guide on ISR G2 UCS-E and VMWare vsphere Hypervisor (ESXi) Revised: November, 2013 Contents Overview, page 1 Guidelines and Limitations, page 1 Prerequisites, page 2 Installation
More informationCreating a Unifi Lab Network on your existing network
Creating a Unifi Lab Network on your existing network This tutorial will outline how to add a Unifi USG-3 and Unifi Switch 8 to your existing network to create a separate subnet. This tutorial assumes
More informationQuick Setup Guide. for Standalone Omada Access Points. EAP110 / EAP115 / EAP225 / EAP245 / EAP320 / EAP330 / EAP115-Wall
Quick Setup Guide for Standalone Omada Access Points EAP110 / EAP115 / EAP225 / EAP245 / EAP320 / EAP330 / EAP115-Wall EAP110-Outdoor / EAP225-Outdoor / EAP225-Wall 1910012420 REV1.0.1 May 2018 Omada EAP
More informationDSL-G624T. Wireless ADSL Router. If any of the above items is missing, please contact your reseller. This product can be set up using any
This product can be set up using any current web browser, i.e., Internet Explorer 6x or Netscape Navigator 7x. DSL-G624T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share your
More informationFUSION RESEARCH. Ovation Music Server. Installation & Setup Guide
FUSION RESEARCH Ovation Music Server Installation & Setup Guide October 2016 GETTING STARTED: The first step to setting up the Ovation Music Server is to make sure that you have connected a hardwire ethernet
More informationWHG405 V2.10. Secure WLAN Controller
WHG405 V2.10 Secure WLAN Controller Copyright Notice This document is protected by USA copyright laws and other laws and is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish,
More informationCGDS - Substation Workbench Release 1.0 Browser Role User Guide
Browser Role User Guide Revised: June 19, 2013 CGDS - Substation Workbench Release 1.0 Substation Workbench Browser Role The Browser Role in CGDS - Substation Workbench has the capabilities needed to monitor
More informationMobility Management Platform from AT&T
Quick start guide to Mobility Management Platform from AT&T For the management of AT&T Work Data and AT&T Work Voice https://mmp.att.com Setting up Mobility Management Platform Click the Set password,
More informationSet Up Voic on Cisco Unified Communications Manager
Set Up Voicemail on Cisco Unified Communications Manager Setting up voicemail requires you to configure Cisco Unity Connection and then add voicemail services on Cisco Unified Communications Manager. You
More informationPort Forwarding Setup (RTA1025W Rev2)
Port Forwarding Setup (RTA1025W Rev2) Port Forwarding Port forwarding enables programs or devices running on your LAN to communicate with the internet as if they were directly connected. This is most commonly
More informationCDR Database Copy or Migration to Another Server
CDR Database Copy or Migration to Another Server Document ID: 66974 Contents Introduction Prerequisites Requirements Components Used Conventions Background Supported Data Sources Topology Copy the CDR
More informationNVR CH Network Video Recorder. Quick Installation Guide v1.0
NVR-0104 4-CH Network Video Recorder Quick Installation Guide v1.0 2 NVR-0104 Quick Installation Guide Package Contents NVR-0104 Network Video Recorder IR Remote controller RJ-45 Ethernet LAN cable Power
More informationCDR Database Copy or Migration to Another Server
CDR Database Copy or Migration to Another Server Document ID: 66974 Introduction Prerequisites Requirements Components Used Conventions Background Supported Data Sources Topology Copy the CDR Database
More informationCisco Unified Serviceability
Cisco Unified Serviceability Introduction, page 1 Installation, page 5 Introduction This document uses the following abbreviations to identify administration differences for these Cisco products: Unified
More informationHow to Configure a Cisco Router Behind a Non-Cisco Cable Modem
How to Configure a Cisco Router Behind a Non-Cisco Cable Modem Document ID: 19268 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify
More informationLab - Connect to a Router for the First Time
Introduction In this lab, you will configure basic settings on a wireless router. Recommended Equipment A computer with Windows installed An Ethernet NIC installed Wireless router Ethernet patch cable
More informationAll - In - One for Hyper- V
All - In - One for Hyper- V INSTALL GUIDE LiveNX All- In- One Server Types and Requirements Here are specifications to LiveNX All- In- One Server types and its OVA requirements. Storage can be expanded
More informationP-792H v2. G.SHDSL.bis Broadband Gateway DEFAULT LOGIN DETAILS. Version 3.70 Edition 1, 04/2010
P-792H v2 G.SHDSL.bis Broadband Gateway Version 3.70 Edition 1, 04/2010 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1 Admin Password: 1234 User Password: user www.zyxel.com Copyright 2010 ZyXEL
More informationTelephony Integration
Introduction, page 1 Phone System, page 2 Port, page 5 Port Group, page 6 Trunk, page 12 Speech Connect Port, page 13 Audio and Video Format Using Phone, page 14 Security, page 15 IPv6 in Unity Connection
More informationDongle-sized Wireless Print Server. Quick Installation Guide V1.0
Dongle-sized Wireless Print Server Quick Installation Guide V1.0 1 Before you start, you should prepare the following items: Windows-based computer with print server setup CD Printer Printer cable One
More informationManaging User Roles and Users in LMS
7 CHAPTER This chapter explains the following: Managing Roles Managing Users Managing Roles A role is a collection of privileges that dictate the type of system access you have. The Manage User Roles workflow
More informationXcalenets Console Setup Guide. Xcalenets Console Setup Guide (Standalone version)
Xcalenets Console Setup Guide Xcalenets Console Setup Guide (Standalone version) 1 Content CONTENT... 2 Getting Started to Xcalenets Console Setup... 3 Account Level Introduction... 3 Login Console Setup...
More informationPort Forwarding Setup (NB7)
Port Forwarding Setup (NB7) Port Forwarding Port forwarding enables programs or devices running on your LAN to communicate with the internet as if they were directly connected. This is most commonly used
More information2. The next screen will tell you to press the lighted Cisco logo on the Router. After you have pressed the logo, click the Next button to continue.
2. The next screen will tell you to press the lighted Cisco logo on the Router. After you have pressed the logo, click the Next button to continue. To exit the Wireless Setup Wizard, click the Exit button.
More informationSkills Assessment Student Practice
Skills Assessment Student Practice Topology Assessment Objectives Part 1: Develop the IPv4 Address Scheme (15 points, 20 minutes) Part 2: Initialize and Reload Devices (10 points, 5 minutes) Part 3: Configure
More informationCisco UCS C-Series. Installation Guide
Installation Guide UPDATED: 04 October 2018 Copyright Notices Copyright 2002-2018 KEMP Technologies, Inc. All rights reserved. KEMP Technologies and the KEMP Technologies logo are registered trademarks
More informationProtect My Ministry Integrated Background Checks for Church Community Builder
Protect My Ministry Integrated Background Checks for Church Community Builder Integration and User Guide Page 1 Introduction Background Check functionality through Protect My Ministry has been integrated
More informationUser Templates. Find BAT User Template. Procedure
This chapter provides information about using Cisco Unified Communications Manager Bulk Administration (BAT) user templates to define the common user attributes to add a group of new users. Find BAT User
More informationNetwork Management Software ALLNET Zone Controller
Network Management Software ALLNET Zone Controller For ALL0558N / ALL02850N / ALL02860ND / ALL02880ND User Manual v1.0 Table of Contents 1. Installation & Un-installation... 4 1.1. Install NMS Suite...
More informationConfiguration Guide. For Managing EAPs via EAP Controller
Guide For Managing EAPs via EAP Controller 1910012313 REV1.0.0 December 2017 CONTENTS 1 Overview... 1 2 Configuration... 2 2.1 Managing EAPs in the Same Subnet... 2 2.2 Managing EAPs in Different Subnets...
More informationTECHNICAL NOTE HOW TO CONFIGURE ALLOYVOICE SIP TRUNKS ON GRANDSTREAM UCM 6XXX SERIES. 1. Introduction. Author: Adam Wells Date: June 6th, 2018
HOW TO CONFIGURE ALLOYVOICE SIP TRUNKS ON GRANDSTREAM UCM 6XXX SERIES 1. Introduction This Technical note will go through information on how to setup AlloyVoice on Grandstream UCM PBX, as well as general
More informationCreate a pfsense router for your private lab network template
Create a pfsense router for your private lab network template Some labs will require a private network where you can deploy services like DHCP. Here are instructions for setting up an uplink router for
More informationStarWind iscsi SAN & NAS:
This document refers to the previous StarWind Virtual SAN version. To view the document for the current version, please follow this link StarWind iscsi SAN & NAS: Configuring HA Storage for Hyper-V October
More informationConfiguration Guide for Integration of Spectralink PIVOT with UNIVERGE 3C
Configuration Guide for Integration of Spectralink PIVOT with UNIVERGE 3C Version 1.0 December 19, 2014 Contents Contents Acronyms... 1 Purpose of this Document... 2 Scope of this document... 2 Configuration...
More informationIf you re not using Microsoft Hyper-V 2012, your screens may vary.
Quick Start Guide If you re not using Microsoft Hyper-V 2012, your screens may vary. VX VIRTUAL APPLIANCES Microsoft Hyper-V Hypervisor Server Mode (Single-Interface Deployment) 2015 Silver Peak Systems,
More informationUsing a USB 3.0 Dual Gigabit Ethernet Bypass Adapter with VMware vsphere for VXOA
Using a USB 30 Dual Gigabit Ethernet Bypass Adapter with VMware vsphere for VXOA This document describes how to use a USB 30 Dual Gigabit Ethernet Bypass Adapter to add bypass functionality to an existing
More informationConfiguring Cisco TelePresence Manager
CHAPTER 3 Revised: November 27, 2006, First Published: November 27, 2006 Contents Introduction, page 3-1 System Configuration Tasks, page 3-2 Security Settings, page 3-3 Database, page 3-4 Room Phone UI,
More informationNetBrain OE System Quick Start Guide
NetBrain Technologies Inc. NetBrain OE System Quick Start Guide For Operator Edition Administrators Table of Contents 1. Install NetBrain OE System... 3 1.1 Install Gateway Server... 4 1.2 Install Network
More informationCisco ATA SPA112 & SPA122.
STEP 1 Connect your device's power and ethernet cables. For users with the SPA112: Connect your router with the supplied Ethernet network cable to the SPA112's internet port. Now connect your phone to
More informationConnect the PC and Log into the GUI
CHAPTER 3 Connect the PC and Log into the GUI This chapter explains how to connect PCs and workstations to the Cisco ONS 15454 and how to log into Cisco Transport Controller (CTC) software, which is the
More informationSonicwall NSA240 / TZ210 Configuration Guide (Firmware: SonicOS Enhanced o & up)
Sonicwall Configuration Guide v1.0 Sonicwall NSA240 / TZ210 Configuration Guide (Firmware: SonicOS Enhanced 5.8.1.1-35o & up) 169 Saxony Road, Suite 212 Encinitas, CA 92024 Phone & Fax: (800) 477-1477
More informationKeyNexus Hyper-V Deployment Guide
v1.0 09/2018 . Copyright Notice Copyright 2018 KeyNexus Inc. All rights reserved. Information in this document is subject to change without notice. The software described in this document is furnished
More informationIP CAMERA CONFIGURATION IN ENVIROMUX WEB INTERFACE
IP CAMERA CONFIGURATION IN ENVIROMUX WEB INTERFACE The E-IPCAM, E-IPCAM-WN, E-IPCAM-WHN, E-IPCAM-NPOE, E-IPCAM-DHNPO(-P)(-E) and E-IPCAM- WHNPT can be used to take snapshots and attach them to alert messages
More informationCloud Control Panel User Manual v1.1
Cloud Control Panel User Manual v1.1 March 2011 Page: 1 / 27 Contents 1 Introduction...3 2 Login procedure...4 3 Using the Dashboard...7 3.1 Enabling the Detailed View...8 3.2 Stopping the component...9
More informationGetting Started with OmniVista Security
Getting Started with OmniVista Security Getting Started with OmniVista Security The Users and User Groups application enables you to control user access to OmniVista and to network switches. Access to
More informationConfiguring Security on the Voice Network
This chapter describes the procedure for configuring security on your Cisco BCS Verified Designs network using Cisco Security Device Manager (SDM). Cisco SDM is a web-based device management tool supported
More information