PASS4TEST. IT Certification Guaranteed, The Easy Way! We offer free update service for one year

Transcription

1 PASS4TEST \ We offer free update service for one year

2 Exam : Title : Managing Industrial Networking for Manufacturing with Cisco Technologies Vendor : Cisco Version : DEMO Get Latest & Valid Exam's Question and Answers 1 from Pass4test.com. 1

3 NO.1 When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect? A. Use of shielded Patch Cables, Bonded on one end only. B. Use of unshielded Patch Cables. C. Broken seal on bulkhead connector. D. Oxidation on Shielded RJ45 Patch Plug Answer: D NO.2 Which statement is correct regarding ProfiNET communication classes? A. ProfiNET-RT traffic is carried in UDP and TCP packets B. ProfiNET-NRT is used to carry time critical status information C. ProfiNET-IRT requires switches with hardware time scheduling capabilities D. ProfiNET-NRT is prioritized as Layer-2 Class-of-Service 1 (CoS 1) NO.3 Which three network mechanisms can be used for securely segmenting an industrial network? (Choose three) A. VLANs B. OSPF C. REP D. VRFs E. Firewalls F. Spanning-tree Answer: A,D,E NO.4 To correctly integrate a Cisco Industrial Ethernet switch into a ProfiNET management system such as SIMATIC STEP 7 or TIA Portal, which is a mandatory action? A. Configure an IP address on the ProfiNET VLAN interface B. The General Station Description (GSD) file must be uploaded from the switch to the management system. C. Enable Quality of Service (QoS) and ensure the management station interface is trusted D. Enable SNMP on the switch Answer: B NO.5 Which two actions are examples of network device hardening for Cisco Industrial Ethernet Switches? (Choose two) A. Disable unused services B. Shutdown network ports which are not in use C. Only allow administrative access using Telnet D. Deploy IP67 versions of Cisco Industrial Ethernet Switches E. Set the native VLAN on all trunk ports to VLAN 1 Answer: A,B Get Latest & Valid Exam's Question and Answers 2 from Pass4test.com. 2

4 NO.6 Exhibit: Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.) A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so shielded cable that is rated for 600 V is advised. B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN. C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting. D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter. E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting. F. IEEE1588 and PTP are important for ensuring real-time synchronization. Answer: A,D,F NO.7 A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104. Both standard controllers must monitor a photocell on this machine. Which IP address is used to transfer this status information? A B C D NO.8 Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch? Get Latest & Valid Exam's Question and Answers 3 from Pass4test.com. 3

5 A. switch#show snooping ip igmp B. switch#show igmp snooping C. switch#show ip igmp snooping D. switch#show ip snooping Get Latest & Valid Exam's Question and Answers 4 from Pass4test.com. 4