LA6584JA. Functions and Applications Single-phase full-wave driver for fan motor. Specitications

Transcription

1 Ordering number : ENA2125 Monolithic Linear IC Single-phase Full-wave Driver For Fan Motor Overview The is Single-phase bipolar fan motor is put into silent driving by means of BTL output linear drive, offering high efficiency and power saving by suppressing the reactive current. Lock protection and rotation signal (, ) circuits are built in, ensuring optimum application to small fans for notebook PC, consumer equipment power supply, car audio system, CPU cooler, etc. that require high reliability and low noise. Functions and Applications Single-phase full-wave driver for fan motor Specitications Absolute Maximum Ratings at Ta = 25 C Parameter Symbol Conditions Ratings Unit Output voltage max 15 V Output current I OUT max 1.2 A Output withstand voltage V OUT max 15 V / output pin output Withstand voltage V / max 15 V / output current I / max 5 ma B output voltage I B max 10 ma Allowable dissipation Pd max Mounted on a specified board* 0.8 W Operating temperature range Topr -30 to +90 C Storage temperature range Tstg -55 to +150 C * Mounted on a specified board (114.3mm 76.1mm 1.6mm, Glass epoxy) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 May, 2013 O1012NKPC S00001 No.A2125-1/5

2 Recommended Operating Range at Ta = 25 C Parameter Conditions Conditions Ratings Unit Supply voltage 2.8 to 14.0 V Common-phase input voltage range of all input VICM 0 to -1.5 V Electrical Characteristics at Ta = 25 C VCC = 12V, unless otherwise specified. Ratings Parameter Conditions Conditions min typ max Unit Circuit current I CC 1 During drive (CT = L) ma I CC 2 During lock protection (CT = ) ma Lock detection capacitor charge I CT μa current Capacitor discharge current I CT μa Capacitor charge and discharge RCT RCD = I CT 1/I CT current ratio CT charge voltage V CT V CT discharge voltage V CT V OUT output L saturation voltage V OL I O = 200mA V OUT output saturation voltage V O I O = 200mA V all input sensitivity VN Zero peak value 7 15 mv (including offset and hysteresis) / output pin L voltage V / I / = 5mA V / output pin leak current I /L V / = 15V 1 30 μa B output L voltage V BL I B = 5mA V Package Dimensions unit : mm (typ) 3179C (0.33) (1.3) 1.5max Allowable power dissipation, Pd max -- W Pd max -- Ta Specified board: mm 3 Material: Glass epoxy Ambient temperature, Ta -- C SANYO : SSOP20(225mil) No.A2125-2/5

3 Truth Table CT OUT1 Mode L L L L L During rotation L L - - OFF OFF - Lock protection Pin Assignment ND 1 20 ND ND 2 19 ND ND 3 18 ND 4 17 OUT CT B Top view No.A2125-3/5

4 Sample Application Circuit *1 Di Cr *4 R2 B *2 OUT1 B R2 *5 CT GND *3 R1 On board element *1 When Di to prevent breakdown in case of reverse connection is used, it is necessary to insert a capacitor Cr to secure the regenerative current route. Similarly, Cr is necessary to enhance the reliability when there is no capacitor near the fan power line. *2 To obtain all bias from VCC, carry out 1/2 VCC bias as shown in the figure. Linear driving is made through voltage control of the coil by amplifying the all output. When the all element output is large, the startup performance and efficiency are improved. Adjustment of the all element can reduce the noise further. *3 When the all bias is taken from the B pin, constant-voltage bias is made with about 2.0V. Therefore, the all element can provide the output satisfactory in temperature characteristics. Adjustment of the all output amplitude is made with R1. (When VCC = 12V, the step *2 above proves advantageous for IC heat generation.) *4 Keep this open when not used. *5 When the wiring from the all output to IC all input is long, noise may be carried through the wiring. In this case, insert the capacitor as shown in the figure. No.A2125-4/5

5 Internal Equivalent Circuit 1.5VRG B OUT1 GND Control Circuit Charge/discharge circuit Discharge pulse CT = 0.47 to 1µF ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC s product/patent coverage may be accessed at SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitabilityof its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2125-5/5