CX27C. Industrial Ethernet Gateway. Special features. Data sheet. Block diagram

Transcription

1 CX27C Industrial Gateway Special features - Gateway between QuantumX measurement modules and -based fieldbuses - Integration with Industrial real-time : PROFINET IRT - Parallel integration with standard for data acquisition with a high data throughput - Synchronization via PROFINET or PTP (IEEE1588:2008), others Data sheet Block diagram Front Rear 10/100/1000 PTPv2 SoC DC Power in V 10/100/1000 PTPv2 Industrial Industrial industrial

2 Specifications General specifications Interfaces (number) PROFINET IRT (2) Gigabit (2) (3) Supply voltage range (DC) V , nominal (rated) voltage 24V Power consumption W < 7 (data link) MBit/s 10 / 100 / 1000 Protocol/addressing - TCP/IP (direct IP address or DHCP) Connection - 8P8C plug (RJ 45) with twisted pair cable (Cat 5) Max. cable length to module m 100 (module synchronization, data link, optional IEEE 1394b (HBM modules only) supply voltage) Baud rate MBaud 400 (approx. 50 MByte/s) Max. current from module to module A 1.5 Max. cable length between the nodes m 5 Max. number of modules connected in series - 12 (=11 hops) (daisy chain) Max. number of modules in a system (including hubs 1, backplane) - 24 Max. chain of hops 2-14 Synchronization options PROFINET IRIG-B (B000 bis B007; B120 bis B127) Protection class Degree of protection Mechanical tests 3 via bus connection CX27C IEE1588:2008 (PTP), NTP via MX840B input channel III IP20 Vibration (30 min) m/s 2 50 Shock (6 ms) m/s EMC requirements according to EN61326 Nominal (rated) temperature range C [ F] [ ] Storage temperature range C [ F] [ ] Rel. humidity % (non condensing) Weight, approx. g 900 Dimensions, horizontal (H x W x D) mm 52.5 x 200 x 122 (with case protection) 44 x 174 x 119 (without case protection) 1 Hub: node or distributor 2 Hop: Transition from module to module/signal conditioning 3 Mechanical stress is tested according to European Standard EN for vibrations and EN for shock. The equipment is subjected to an acceleration of 25 m/s 2 in a frequency range of Hz in all 3 axes. Duration of this vibration test: 30min per axis. The shock test is performed with a nominal acceleration of 200 m/s 2 for 11 ms, half sine pulse shape, with shocks in each of the 6 possible directions. HBM 2

3 Specifications PROFINET IRT / RT Function Interfaces PROFINET device 100 Base-TX- (switched) with 2xRJ45 Cable length (max.) m 100 Cabel type (min. requirement) Standard Cat 5, shielded PROFINET Communication Max. Number of cyclic process data (PDOs) 200 (2048 bytes process data [input]) Max. Number of slots / subslots 32 / 199 ( 2 kh) 32 / 180 (4 khz) Minimum cycle time μs 250 (IRT) Minimum time latency from MX input to μs 1000 PROFINET PROFINET specification V2.3 Conformance Classes B, C Media Redundancy Protocol (MRP) supported Process data configuration MX Assistant, GSDML Diagnose Status Byte Workflow Use the free MX Assistant software to parameterize the measurement modules (MX) input channels, activate them for isochronous real-time operation, and assign them to the fieldbus. Create a description file and import it into the PLC Controller software. Data rate, max. Meas. values/s HBM

4 Accessories, to be ordered separately CX27C accessories Article Description Order no. Power AC/DC power pack / 24 V Input: V AC ( 10 %), 1.5 m cable Output: 24 V DC, max A, 2 m cable with ODU plug 3 m cable - QuantumX supply 3 m cable for voltage supply of QuantumX modules; suitable plug (ODU Medi Snap S11M08-P04MJGO-5280) at one end and exposed wires at the other. Communication cable (module to module) Mechanic Connecting elements for QuantumX modules Connecting elements for QuantumX modules connection cable for QuantumX or SomatXR modules; with matching plugs on both sides. Length 0.2 m/2 m/5 m Note: The cable enables modules to be supplied with power (max. 1.5 A, from the source to the last drain). Connecting elements (clips) for QuantumX modules; Set comprising 2 case clips including mounting material for fast connection of 2 modules. Fitting panel for mounting of QuantumX modules using case clips (1-CASECLIP), lashing strap or cable tie. Basic fastening by 4 screws. QuantumX Backplane (Standard) QuantumX Backplane Standard for a maximum of 9 modules; General: - Mounting on wall or control cabinet (19 ) Connection of external modules by possible; Power supply: 24 V DC / max. 5 A (150 W); QuantumX Backplane (Rack) QuantumX Backplane Rack for maximum 9 modules; 19'' rack mounting with handles left and right; Connection of external modules via possible; Power supply: 24 V DC / max. 5 A (150 W). 1-NTX001 1-KAB KAB KAB KAB CASECLIP 1-CASEFIT 1-BPX001 1-BPX002 HBM 4

5 Accessories, to be ordered separately (continued) General accessories Article Description Order No. Software and product packages EVIDAS NEW Test & Measurement software for data acquisition, analysis, visualization and storage. single seat license 1 EVIDAS EVIDAS Main Features: - Fast and comfortable channel configuration using TEDS, Sensor Database, directly in channel list or by individual dialog - Test & measurement job parameterization - Individual data visualization (live and past recordings) - Data analysis and online calculation - Save and export data in different formats (e.g. EVIDAS, Excel, ASCII, MDF, MATLAB) - Data transfer to HBM cloud-space Includes software maintenance for 12 months NEW Test & Measurement software for data acquisition, analysis, visualization and storage. floating network license 1 EVIDAS FN catman AP catman EASY Complete package including catman Easy functionality plus additional modules such as integration of video cameras (EasyVideoCam), complete post process analysis (EasyMath), automation of recurring processes (EasyScript), offline preparation of measurement projects (EasyPlan) as well as additional functions such as calculating electrical power, special filters, frequency spectrum, etc. More details at The basic software package for measurement data acquisition comprises convenient channel parameterization using TEDS or the sensor database, measurement job parameterization, individual visualization, data storage and reporting. 1 CATMAN AP 1 CATMAN EASY catman PostProcess Post Process edition for visualization, preparation and analysis of measurement data, including many mathematical functions, data export and reporting. 1 CATEASY PROCESS LabVIEW TM Treiber 1 Universal driver from HBM for LabVIEW TM. 1 LabVIEW DRIVER CANape driver QuantumX driver for the software CANape from Vector Informatik. CANape versions from 10.0 are supported. 1 More drivers and partners at 1 CANAPE DRIVER 5 HBM

6 Subject to modifications. All product descriptions are for general information only. They are not to be understood as a guarantee of quality or durability. measure HBM and predict with confidence 6 Hottinger Baldwin Messtechnik GmbH Im Tiefen See Darmstadt Germany Tel Fax info@hbm.com