Table of contents. Toughpower. Toughpower. 1.Introduction 02 2.Product Features 3.Components Check

Transcription

1 Table of contents.introduction 0.Product Features.Components Check.Connectors 5.Installation Steps 6.+V Rail Distribution 7.SPEC Table 8.Other Specification 9.Trouble Shooting 0.Contact Us

2 . Introduction. Statement We live up to the promise of Thermaltake logo in our unending quest for excellence. Shall you have any suggestion or comments, please access our website: or to: We appreciate your kindly feedback and you will receive the prompt response from our customer service team. Please take the time in familiarizing yourself with the power supply, its connectors and the contents of this manual before proceeding with the installation of the power unit. You will need a Philips crosshead screwdriver, perhaps your PC case manual and most certainly your motherboard manual. Should you have any questions regarding the content of the manual, please contact Thermaltake directly. Failure to follow the proper procedures may cause severe bodily harm or PC component damage.. Warnings and Cautions.. Do not pull the AC power cord when the power supply is in use or the damages to the components will occur... Do not store the Power Supply in high humidity and high temperature environment... When using Toughpowet 850W power supply under testing conditions where the power supply unit is not installed in a PC with its components, please follow the steps below: ) Please take a paper clip and untwist it. ) Make sure the power supply unit is in the "OFF" position. ) Locate the 0+ pin motherboard connector from the power supply unit. ) Plug one side of the paper clip into the green wire hole. 5) Plug the other side of the paper clip into any of the black wire holes. 6) Turn on the PSU to see if the power supply fan(s) turn(s) on... High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician...5 All warrantees and guarantees shall be voided should there be a failure to comply with any of the warnings and cautions covered in this manual. 0 0

3 . Product Features. NEW 8 pin PCI-E Connector 850W power supplies come with two of the latest 8-pin PCI-E connectors required for the next generation NVIDIA and AMD graphics cards. These new defined 8-pin connectors are downward compatible with the existing 6-pin PCI-E connectors with an 8 pin to 6 pin converter.. Excellent Efficiency (up to 87%) 850W provide excellent efficiency and hence reducing energy consumption. The higher the efficiency the more you will save on your energy bill.. 0mm Ball-Bearing Fan The 0mm ball bearing fan effectively increases the airflow inside the PSU and decreases the ambient temperature.. Extremely good voltage regulation ( %) This feature allows tighter load regulation ( %) than other power supplies ( 5%) and increase system voltage stability..6 Four Independent +V rails Four independent +V rails are provided to support the high-end graphic card and PC system..7 Industrial grade components All components are specially designed for industrial environment and extreme conditions..8 Hi-Tech Coating With special Hi-Tech coating, 850W PSUs looks professional, elegant and unique..9 High +5VSB Output Built-in higher +5VSB (from A to.5a(peak load)) supports up to USB devices. Also, even the system is power off, USB devices can still be charged by the A sustained output..5 MTBF > 0,000 hours (Highly reliable) 0,000 hours of MTBF (Mean Time between Failures) goes above and beyond all ATX specifications. 0 05

4 . Components Check. Connectors. Main Power Connector (0+ pin) Support the latest ATX V. system motherboard One 850W power supply unit One AC Input power cord Voltage +.V +.V +5V +5V PWR_ON +5Vsb +VDC +VDC +. V Color Orange Orange Gray Purple Orange PIN PIN Color Orange Blue Green N/C Voltage +. V - V PS_ON# N/C +5 V +5 V +5 V mounting screws User manual 06 07

5 . CPU Connector ( pin) Support both dual core CPU and single core CPU systems motherboard +V DC +V DC. CPU Connector (8 pin) Support the latest 8 pin Quad Core system motherboard. PCI-E Connector (8 pin) Support next generation 8 pin sockets on high-end graphic cards and can support the existing 6 pin sockets by connecting to the 8 pin to 6 pin converter. +VDC +VDC +VDC GND GND GND GND GND.5 PCI-E Connector (6 pin) Support the latest high-end graphic cards with 6 pin socket VDC +VDC +VDC +VDC VDC VDC VDC

6 .6 SATA Connector (5 pin) Support the new generation high-speed SATA devices.8 Floppy Disk Connector ( pin) Support Floppy Disk and some other additional devices +VDC +5VDC Orange +. VDC 5 +5VDC +VDC.7 Peripheral Connector ( pin) Support IDE/SCSI (HDD/CD/DVD..etc) devices +VDC Connector x /0-pin motherboard connector x 8/-pin EPSV connector x 6-pin PCI-E connector, x 8-pin PCI-E connector x quad SATA power connectors x quad -pin IDE & single floppy power connectors x quad -pin IDE & single floppy power connectors 500mm 500mm 500mm 500mm+50mm+50mm+50mm 500mm+50mm+50mm+50mm+50mm 500mm+50mm+50mm+50mm+50mm +5VDC 0

7 5. Installation Steps To prevent electrical shocks, please disconnect the power cord from your existing power supply unit. 850W Power Supply has automatic voltage selector which will automatically change to 00V-0V PSU. Step Connect the 6 pin/8 pin PCI-Express connector to your graphic card if needed. Step After install the power supply unit into the chassis and then connect the 0+-pin main power cable to motherboard 0pin or pin socket. Step Connect the -pin/8-pin +V auxiliary power connector to the motherboard. (Users can use either pins or 8 pins, depending on the motherboard. Please check with the motherboard user's manual.) Step Connect the pin power connector to peripheral devices such as DVD-Burner, hard drive, and etc. In addition, a user can connect the -pin floppy power connector to connect the floppy drive.

8 6. +V Rail Distribution If there are S-ATA hard disk drives present, there are also Serial ATA connectors available. W07RU 850W pin +V V pin +V V 8 pin +V V,V Peripheral & Floppy V S-ATA V Modular 6pin PCI-E Connector V,V Modular 6pin PCI-E Connector V,V Native 8pin PCI-E Connector V,V Native 8pin PCI-E Connector V,V 5

9 7. SPEC Table 8. Other Specification Model Power Dimension Switches PFC Cooling System Noise P. G. Signal Efficiency Hold-up Time Input Voltage Input Frequency Range MTBF Input Current +.V +5V +V +V +V +V -V +5Vsb Total Power Peak Power Operating Temp. Storage Temp. Operating Humidity Storage Humidity Over Voltage Protection Over Current Protection Short Protection W07RU SPECIFICATION 850W 60mm(L)x50mm(W)x86mm(H) ATX Logic on-off additional power rocker switch Active PFC (PF > 0.9) 0mm Fan, 00RPM 0% 6 dba at 00 RPM ms up to 87% 6ms INPUT 00 VAC ~ 0 VAC 7 ~ 6 H z 0,000 hrs minimum 0A / 5A OUTPUT * Max/Min Regulation * Ripple & Noise Output 0A/0.5A +,-% 50mV 99W 0A/A +,-% 50mV 50W 8A/A +,-% 0mV 8A/A +,-% 0mV 0A/A +,-% 0mV 7W 0A/A +,-% 0mV 0.8A/0A +9,-5% 0mV 9.6W A/0A +,-% 50mV 5W 850W 950W(60S) ENVIRONMENT 0 to 50-0 to 70 0% to 90%, non-condensing 5% to 95%, non-condensing PROTECTION Trigger Point/Range.5 Vmax 7.0 Vmax 5.6 Vmax DC rail +.V trip point +5.0V trip point +.0V trip point +.V 5A ~ 50A +5.0V A ~ 50A +V & +V A ~ 9A +V & +V A ~ 8A All output to GND 8. Inrush Current: 55A max. when AC input 5Vac at 5 cold start. 0A max. when AC input 0Vac at 5 cold start. 8. Power Efficiency 80%(min.) at full load(typical) and 5Vac input. 8. CE Requirements 8.. Conducted EMI. Meet FCC: ClassB. Meet CISPR : ClassB. Meet BSM I: ClassB 8.. Safety Standards.Meet CUL (U L ).Meet TUV EN60950.Meet CB (IE C 950).Meet CE 8.. Harmonic Meet IEC000--, Class D 6 7

10 9.Trouble Shooting Condition : No DC output. The fan or fans are motionless. Check: - Is the AC inlet plug firmly plugged into the PSU inlet socket? - Is the wall socket, extension power cord, power strip or surge protector in use, fully functional and wall power switch turned ON? - Is the Main Board socket (0+ pin) plug fully and firmly inserted? Condition : The fan or fans began rotating and then stopped. The system hangs without proceeding any further. Check: - Are the peripheral connectors firmly plugged into accessory devices, such as the main hard drive, CD ROM, etc? - If a plug has been inadvertently connected in an offset or reversed position, unplug the AC power source, reconnect the offending connectors and then wait for 0 seconds before replug in the AC power source and try again. Note: If the power supply is still unable to power up after following the above instruction, please send the unit back to your dealer or retailer for after sales service. 0. Contact us For further technical supports or general inquiries, please contact us at: Thermaltake Technology USA Toll Free: (800) support-usa@thermaltake.com Thermaltake Europe B.V. Tel: tt.europe@thermaltake.com Thermaltake Germany GmbH TEL: +9 (0) support@thermaltake.de Thermaltake Beijing Co.Ltd. Tel: /89 ext.6 doctort@thermaltake.com.cn Thermaltake Australia and New Zealand Pty Ltd Tel: sales@thermaltake.com.au Thermaltake Japan Inc. sales-jp@thermaltake.co.jp 8 9