TR2 1000W. User's Manual >> ATX12V 2.2 & EPS 12V 2.91 Version. ATX 12V 2.2 & EPS 12V 2.91 Version. Thermaltake TR2 Power Supply

Transcription

1 TR2 000W ATX V 2.2 & EPS V 2.9 Version User's Manual >> Thermaltake TR2 000W Power Supply Thermaltake TR2 thermaltake@thermaltake.com Power Supply sales.tr@tr2tt.com

2 Table of contents. Introduction Components Check Installation 3. Warrings and Cautions Installation Steps Product Specification 4. Output Specification TR2 000W Power Supply Other Specificatio n Protection Environments EMI & Safety Trouble Shooting Cable Retail Package

3 . Introduction 2. Components Check We live up to the promise of Thermaltake logo in our unending quest for excellence. Shall you have any suggestion or comments, please access our web site : or to : thermaltake@thermaltake.com sales.tr@tr2tt.com we appreciate your kindly feedback and you will receive the prompt response from our customer service team. 000W power supply unit One AC Input power cord Thank you for choosing a quality Thermaltake TR2 000W PC Power Supply. We trust that you will find it providing you with many years of service. 4 mounting screws You can always find a Thermaltake TR2 000W PC Power Supply that is suitable for all of your modern PC power needs. User manual Please take the time in familiarize yourself with the power supply, its connectors and the contents of this manual before proceeding with the installation of the power unit. You will need a Phillips crosshead screwdriver, perhaps your PC case manual and most certainly your motherboard manual. 000W 0 02

4 3 Installation 3. Warnings and Cautions 3.. Do not pull the AC power cord when the power supply is in use or else damage to components will result Do not store the Power Supply in a high humidity and high temperature environment When using TR2 000W power supply under testing conditions where the power supply unit is not installed in a PC with its components, please follow the steps below: )Please take a paper clip and untwist it. 2)Make sure the power supply unit is in the "OFF" position. 3)Locate the 20 or 24 pin motherboard connector from the power supply unit. 4)Plug one side of the paper clip into the green wire hole. 5)Plug the other side of the paper clip into any of the black wire holes. 6)Turn on the PSU to see if the power supply fans turn on High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. 3.2 Installation Steps 3.2. Disconnect the power cord from your old power supply Follow your computer case manual and disassemble the case Disconnect all the power connectors from the motherboard and from the peripheral devices such as case fans, hard drives, floppy drives. etc Remove the existing power supply from your computer case and replace it with your new Thermaltake Connect the power connectors to the motherboard and peripheral devices (refer to the rest of this manual to match the various one-way key-locked connectors to the motherboard and accessories) Connect the 6pin or 8pin PCI-E connector to PCI Express graphic card if you need. Note: Please read the user manual supplied with your graphic card for detail usage instructions Close the computer case Make sure your power supply switch is on "OFF" position, and connect the supplied power cord to your Thermaltake All warrantees and guarantees shall be voided should there be a failure to comply with any of the warnings and cautions covered in this manual

5 4. Product Specification 4. Output Specification Main Power Voltage +3.3 V +3.3 V +5 V +5 V PWR_ON +5 Vsb + V + V +3.3 V Color Orange Orange Gray Purple Orange Color Orange Blue Green N/C Voltage +3.3 V - V PS_ON# N/C +5 V +5 V +5 V PCI-E (8 pin) +V +V 2 +V PCI-E (6 pin) CPU (4+4 pin) +V +V 2 +V V 5 +V 6 +V +V

6 CPU (4 pin) 2 +V 3 +V 4 Serial ATA Power +V 2 +5VDC 3 4 Orange +3.3VDC 5 Peripheral (4 pin) +V 8 pin PCI-E to 6 pin PCI-E Converter Enable 8pin PCI-E connector connect to the graphic card that only has 6pin PCI-E socket VDC 4 +V Rail Distribution W06-000W PSU Floppy Disk (4 pin) +V +V2 +V3 +V4 20+4pin Main Power +5VDC 4+4pin CPU Power 2 4 pin CPU Power 3 Peripheral & Floppy +V 4 S-ATA 6 pin standard PCI-E 6 pin standard PCI-E 8 pin standard PCI-E 8 pin standard PCI-E 0 08

7 4.2 Specification Model W06 SPECIFICATION Power Dimension Switches PFC Cooling System Efficiency Hold-up Time 000W 40mm(L)x50mm(W)x86mm(H) ATX Logic on-off additional power rocker switch Active PFC (PF > 0.9) 0mm ball-bearing Fan 300 RPM 0% Typical load of 80% at 5V / 230V input Typical Load 20ms INPUT Input Voltage Input Frequency Range MTBF Input Current 5 VAC- 230 VAC 4 ~ 63 Hz 00,000 hrs minimum at 25 C 4.5A -.5A OUTPUT Voltage Max/Min Regulation Ripple & Noise Output +3.3V 30A/0.8A 30A/0.5A +5,-5% +5,-5% 5mV +5V 5mV 5W +V 20A/0.5A +5,-5% 40mV +V2 20A/0.5A +5,-5% 40mV +V3 20A/0.5A +5,-5% 40mV 95W +V4 20A/0.5A +5,-5% 40mV +5Vsb -V.0A/0.0A 3.0A/0.A +0,-0% +5,-5% 200mV 5mV 25W Total Power 000W Peak Power 00W(3S) ENVIRONMENT Operating Temp. 0 to 50 Storage Temp. -20 to 80 Operating Humidity Storage Humidity 5% to 95%, non-condensing 5% to 95%, non-condensing PROTECTION Items DC rail Trigger Point/Range Over Voltage Protection Over Current Protection Short Protection +3.3V trip point +5.0V trip point +.0V trip point +3.3V +5.0V 3.6V~4.8V 5.6V~.0V 3.5V~6.5V 60A Max. 48A Max. +V 30A Max. All output to GND Technology Features - Four +V Rails - EPS Structure - Hi-Tech housing - Intelligent temperature control 0mm Fan Total Output X X X X6 X 24-pin Main 6-pin PCI Express 8-pin +V Power X2 X2 X2 8-pin PCI Express Performance AC INPUT DC OUTPUT Maximum Load Minimum Load Max Combined Wattage 4-pin +V Power 8-pinto 6-pin PCI Express Ten S-ATA s 4-pin Peripheral Power 4-pin Floppy Drive 0V-240V 3-6.5A 50-60Hz X0 5-pin SATA +3.3V +5V +V +V2 +V3 +V4 -V +5VSB 30A 30A 20A 20A 20A 20A A 3A 0.8A 0.5A 0.5A 0.5A 0.5A 0.5A 0.0A 0.A 5W 95W The continuous total output power is 000W, peak 00W(3 sec.) Total combined +V output load shall be 5A. 25W 09 0

8 4.3 Other Specification 4.3. Inrush Current: Maximum inrush current from power-on (with power on at any point on the AC sine) and including, but not limited to, three line cycles, shall be limited to a level below the surge rating of the input line cord, AC switch if present, bridge rectifier, fuse, and EMI filter components. Repetitive ON/OFF cycling of the AC input voltage should not damage the power supply or Cause the input fuse to blow Power Efficiency: Loading Full load Typical load Light load 5V Required Minimum Efficiency 6% 80% 80% 230V Required Minimum Efficiency 80% 80% 80% Note: The combined power of +5V and +3.3V is 5W max. Add 0.uF and 0uF capacitors across output terminal during ripple & noise test Hold-Up Time: 20mSec. minimum at typical load Power Good Delay: msec Power Fail Delay: > msec Rise Time: 20ms max at full load MTBF at 25 C(demonstrated) 00KHrs minimum 4.4 Protection: If the power supply protection that latch off all main outputs. ( when OCP, OVP or short protection is working ).Reset by cycling remote on/off control or AC power Over Current Protection Output Voltage +3.3V +5.0V +V Over Voltage Protection +3.3V output 3.6V ~ 4.8V +5.0V output 5.6V ~.0V +.0V output 3.5V ~ 6.5V Short Protection All output to GND. 4.5 Environment: 4.5. Operating Temp. +0 C to +50 C Storage Temp. -20 C to +80 C Operating Humidity 5% to 95%, non-condensing Storage Humidity 5% to 95%, non-condensing 4.6 EMI & Safety Trigger Point 60A Max. 48A Max. 30A Max EMI Regulatory - FCC Part 5 Subpart J, class 'B' - CISPR 22 Class 'B' Safety - NEMKO EN VDE EN CSA C22.2 NO IEC UL CE

9 5. Trouble Shooting Condition : No DC output. The fan or fans are motionless Check: - Is the AC inlet plug firmly plugged into the PSU inlet socket? -2 Is the wall socket, extension power cord, power strip or surge protector in use, fully functional and wall power switch turned 'ON'? -3 Is the Main Board socket (24pin) plug fully and firmly inserted? Condition 2: The fan or fans began rotating and then stopped. The system hangs without proceeding any further. Check: 2- Are the peripheral connectors firmly plugged into accessory devices, such as the main hard drive, CD ROM, etc? 2-2 If a plug has been inadvertently connected in an off-set or reversed position, unplug the AC power source, reconnect the offending connectors and then wait for 30 seconds before replug in the AC power source and try again. Note: If the power supply is still unable to power up after following the above instruction, please send the unit back to your dealer or retailer for after sales service. Should you have any questions regarding the aforementioned steps, please contact Thermaltake directly. Failure to follow the proper procedures may cause severe bodily harm or PC component damage. For Support or General Inquiries, please contact us at: Thermaltake Technology USA Toll Free: (800) info@thermaltakeusa.com Thermaltake Europe B.V. Tel: tt.europe@thermaltake.com.tw Thermaltake Beijing Co.Ltd. Tel: /389 ext.6 doctort@thermaltake.com.cn Thermaltake Australia and New Zealand Pty Ltd Tel: sales@thermaltake.com.au Thermaltake Japan Inc. sales-jp@thermaltake.co.jp 3 4

10 6.Cable Retail Package(Optional) P/N:A269 PSU Adaptor Cable Specification Model Model Dimension (mm) type Cable sleeving color Material Weight Voltage ( A ) Adaptor Cable 93mm 4 pin - 8 pin Plastic 6g V ( B ) Adaptor Cable 98mm 20 pin -24 pin Plastic 58g 3.3V,5V, +v,-v (A)4pin-8pin (B)20pin-24pin 5