Kontron User's Guide UGM-M72

Transcription

1 Kontron User's Guide UGM-M72 Document Revision 1.00

2 This page is intentionally left blank

3 Table of Contents 1 User Information About This Document Copyright Notice Trademarks Standards Warranty Technical Support Introduction UGM-M Block Diagram Functional Description Overview Detailed Descriptions D Acceleration Features D Acceleration Features Display Features DVI/HDMI Features Integrated HD Audio Controller (Azalia) and Codec LVDS CRT DAC TVOut Motion Video Acceleration Bus Support Power Management Internal Thermal Sensor Signal Descriptions Connector Locations DVO Connector Fan Connector UGM Module Connector Connector Pinout PCI Express Pins LVDS Flatpanel Signals Flatpanel Power Management Signals TMDS Panel Interface CRT 1 Signals TV Out Interface / 2nd CRT (Optional) ITU-656 Capture Port Thermal- / Power-Management Signals UGM Configuration Power Supply UGM Connector Summary Specifications Electrical Specifications Environmental Specifications Mechanical Specifications Known Restrictions Revision History...19 Kontron User's Guide UGM-M72 iii

4 Kontron User's Guide UGM-M72 iv

5 1 User Information 1.1 About This Document This document provides information about products from Kontron Embedded Modules GmbH and/or its subsidiaries. No warranty of suitability, purpose, or fitness is implied. While every attempt has been made to ensure that the information in this document is accurate, the information contained within is supplied as-is and is subject to change without notice. For the circuits, descriptions and tables indicated, Kontron assumes no responsibility as far as patents or other rights of third parties are concerned. 1.2 Copyright Notice Copyright Kontron Embedded Modules GmbH All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron Embedded Modules GmbH. DIMM-PC, PISA, ETX, ETXexpress, microetxexpress, X-board, DIMM-IO and DIMM-BUS are trademarks or registered trademarks of Kontron Embedded Modules GmbH. Kontron is trademark or registered trademark of Kontron AG. 1.3 Trademarks The following lists the trademarks of components used in this board. IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corp. Microsoft is a registered trademark of Microsoft Corp. Intel is a registered trademark of Intel Corp. All other products and trademarks mentioned in this manual are trademarks of their respective owners. 1.4 Standards Kontron Embedded Modules GmbH is certified to ISO 9000 standards. 1.5 Warranty This Kontron Embedded Modules GmbH product is warranted against defects in material and workmanship for the warranty period from the date of shipment. During the warranty period, Kontron Embedded Modules GmbH will at its discretion decide to repair or replace defective products. Within the warranty period, the repair of products is free of charge as long as warranty conditions are observed. The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by the buyer, unauthorized modification or misuse, operation outside of the product s environmental specifications or improper installation or maintenance. Kontron Embedded Modules GmbH will not be responsible for any defects or damages to other products not supplied by Kontron Embedded Modules GmbH that are caused by a faulty Kontron Embedded Modules GmbH product. Kontron User's Guide UGM-M72 5

6 1.6 Technical Support Technicians and engineers from Kontron Embedded Modules GmbH and/or its subsidiaries are available for technical support. We are committed to making our product easy to use and will help you use our products in your systems. Before contacting Kontron Embedded Modules GmbH technical support, please consult our Web site at for the latest product documentation, utilities, and drivers. If the information does not help solve the problem, contact us by telephone or . Asia Europe North/South America Kontron Asia Inc. Kontron Embedded Modules GmbH Kontron America 4F, No.415, Ti-Ding Blvd., NeiHu District, Taipei 114, Taiwan Brunnwiesenstr Deggendorf Germany Stowe Drive Poway, CA Tel: Tel: +49 (0) Tel: +1 (888) Fax: Fax: +49 (0) Fax: +1 (858) mailto:sales@kontron.com.tw mailto:sales-kem@kontron.com mailto:sales@us-kontron.com Kontron User's Guide UGM-M72 6

7 2 Introduction 2.1 UGM-M72 UGM-M72 is a high performance PCI Express graphic subsystem according to the Universal Graphics Module (UGM) standard. It is based on the AMD/ATI Mobility Radeon HD2400 controller. Its main features are DirectX10 and OpenGL2.0 support, a high definition Unified Video Decoder (UVD) and fully integrated HDMI/HDCP support including 5.1 audio. It is available in a 128MB and a 256MB GDDR3 version. 2.2 Block Diagram Kontron User's Guide UGM-M72 7

8 3 Functional Description 3.1 Overview Chipset: Memory: Clocks: Outputs: Inputs: AMD/ATI M72 (Mobility Radeon HD2400) 128/256MB GDDR3; 64 Bit Interface 450MHz Engine / 400MHz Memory 1 x DVI / HDMI; Single Link; 165MHz 1 x LVDS; 2x24Bit; 2x130MHz 2 x CRT; 10Bit Resolution; 400MHz (2nd CRT optional) 1 x TV; 10Bit Resolution; Composite / S-Video / Component 1 x ITU Bit Digital Capture Port 3.2 Detailed Descriptions D Acceleration Features Hardware acceleration for BitBLT, line drawing, polygon and rectangle fills, bit masking, monochrome expansion, panning and scrolling, scissoring, and full ROP support (including ROP3). Optimized handling of fonts and text using AMD proprietary techniques. Game acceleration including support for Microsoft's DirectDraw: Double Buffering, Virtual Sprites, Transparent BLT, and Masked BLT. Acceleration in 8/15/16/32-bpp modes. Support for WIN 2000 & WIN XP GDI extensions: Alpha BLT, Transparent BLT, Gradient Fill. Hardware cursor support up to 64x64x32-bpp, with alpha channel for direct support of WIN 2000 & WIN XP alpha cursor standard D Acceleration Features Fully DirectX 10.0 compliant, including full speed 32-bit floating point per component operations Shader Model 4.0 geometry and pixel support in a unified shader architecture: Full speed 32-bit floating point processing per component. High dynamic range rendering with floating point blending, texture filtering and anti-aliasing support. High performance dynamic branching and flow control. Nearly unlimited shader instruction store, using an advance caching system. Advanced shader design, with ultra-threading sequencer for high efficiency operations. Advanced, high performance branching support, including static and dynamic branching. 32-bit floating point components for high dynamic range computations. Full anti-aliasing on render surfaces up to and including 128-bit floating point formats. Supportfor OpenGL 2.0 Anti-Aliasing Filtering: 2x/4x modes. Sparse multi-sample algorithm with gamma correction, programmable sample patterns, and centroid sampling. Temporal anti-aliasing. Adaptive anti-aliasing mode. Lossless color compression (up to 8:1) at all resolutions, up to and including widescreen HDTV. Kontron User's Guide UGM-M72 8

9 Anisotropic Filtering: 2x/4x/8x/16x modes Up to 128-tap texture filtering. Adaptive algorithm with performance (bi-linear) and quality (tri-linear) options. Improved quality mode due to improved subpixel precision, higher precision LOD computations, and rotationally invariant LOD computations. Advanced Texture Compression (3Dc+ ): High quality 4:1 compression for normal maps and luminance maps. Works with any single-channel or two-channel data format. HW support to overcome "Small batch" issues in CPU limited applications. 3D resources virtualized to a 32b addressing space, for support of large numbers of render targets and textures. New vertex cache and vertex fetch design, to increase vertex throughput from previous generations. Full support of 64b and 128b textures and surfaces, which can be 4x to 8x faster than previous generation of HW. Up to 8k x 8k textures, including 128b/pixel texture are supported. New multi-level texture cache to give optimal performance, greater than 8x the previous designs. High efficiency ring bus memory controller: Programmable arbitration logic maximizes memory efficiency, software upgradeable. Fully associative texture, color, and Z cache design. New hierarchical Z & Stencil buffers with Early Z Test. New lossless Z-buffer compression for both Z and Stencil. Fast Z-Buffer Clear. Z cache optimized for real-time shadow rendering. Z and color compression resources virtualized to a 32-bit addressing space, for support of multiple render targets and textures simultaneously Display Features Dual independent display controllers supporting 30-bpp throughout the display pipe. Full feature symmetry in both controllers DVI/HDMI Features Supports one single link DVI or one HDMI link Meets Vista logo requirements Mbps/channel with 165 MHz pixel clock rate Supports industry standard EIA-861B video modes including 480p, 720p, 1080i and 1080p. Dithering and frame modulation from the 30-bpp internal pipeline to 18 or 24 bit panels. Fully compliant with the DVI electrical specification Integrated HD Audio Controller (Azalia) and Codec Integrated HD Audio codec supports linear PCM and Dolby Digital (5.1) audio formats for HDMI output. Separate logical chip function. Uses Microsoft UAA driver. Internally connected to the HDMI interface Support for basic audio (32, 44.1 or 48 khz stereo) and Dolby Digital or DTS at the same sample rates. Kontron User's Guide UGM-M72 9

10 3.2.6 LVDS takes output from either one of the internal display controllers. can operate in either single or dual channel mode supporting displays up to QXGA. can drive either 18 bpp or 24 bpp displays with several dithering options from the internal 30 bpp display controller. Ratiometric expansion and compression supported on reduced blank panels. FPDI-2 compliant; compatible with industry standard receivers LVDS eye pattern to improve testability of LVDS module. Fully compliant with electrical specification of ANSI/TIA/EIA CRT DAC triple 10-bit DAC with built-in reference circuit, takes output from either one of the internal display controllers (primary or secondary) or the internal analog TV encoder. Support for stereo sync signal to drive a 3D display. Maximum pixel frequency of 400 MHz. Individual power down feature for each of the 3 guns. Fully compliant with electrical specification of VSIS. dynamic monitor detection for hot-plug/unplug capability TVOut CE class TV encoder for YPbPr, NTSC and PAL (all variants supported). Can take its input from either internal display controller Component output: YPbPr for 480i, 480p, 576i, 576p, 720p, and 1080i. YC S-video output for NTSC & PAL. Composite output for NTSC & PAL. Support for underscan in all TV modes. Scaling and internal adaptive flicker filtering available on both display paths for interlaced TV outputs. Macrovision 7.1x or CGMS copy protection support. Capable of supporting the following VBI data insertion standards: Line 21 for NTSC data on odd and even fields separately, including Closed Caption, Parental Rating information and other Extended Data Services (EDS). Wide Screen Signaling (WSS) for both PAL and NTSC, including the Analog Copy Generation Management System (CGMS-A). Teletext data for PAL. NABTS data for NTSC Motion Video Acceleration Motion Video Acceleration for HD DVD/Blu-ray technology Dedicated UVD (Unified Video Decoder) hardware for H.264 and VC-1 decode: H.264 implementation is based on the ISO/IEC spec. VC-1 implementation is based on the SMPTE 421M spec. Video scaling and fully programmable YCrCb to RGB color space conversion for fullscreen / full-speed video playback and fully adjustable color controls. VIDEOSOAP noise removal filtering for captured video. MPEG1/2/4 decode and encode acceleration: Hardware motion compensation idct/dct and color space conversion HW DXVA parser support for idct MPEG-4 Simple Profile support All-format DTV/HDTV decoding. Supports top quality DVD and time-shifted SDTV/HDTV television playback with the lowest CPU usage. Kontron User's Guide UGM-M72 10

11 Adaptive de-interlacing filter eliminates video artifacts caused by displaying interlaced video on non-interlaced displays, and by analyzing image and using optimal deinterlacing function on a per-pixel basis. Hardware automatically switches to a lower engine clock frequency if the ASIC is idle or partially idle. Advanced Video Processor (AVP) A memory to memory advanced video processor that reads pixels from source frame buffer, processes pixel data, and writes the output pixels to destination frame buffer. Processing includes color space conversion, chroma subsampling format conversion, horizontal and vertical scaling, directional deinterlacing, and gamma correction, all in one pass. AVP offloads format conversion, deinterlacing and scaling tasks from the 3D engine, allowing for reduced memory bandwidth usage, ALU load, and power consumption Bus Support PCI Express 1.1 compliant. Native x16 PCI Express bus interface. Supports x1, x2, x4, x8, and x16 lane widths. Supports Mobile Graphics Low-Power Addendum to the PCI Express Base Specification Power Management Full ACPI 1.0b, OnNow, and IAPC (Instantly Available PC) power management. Static and dynamic power management support (APM as well as ACPI) with full VESA DPM and Energy Star compliance. Full POWERPLAYTM 7.0 support. The chip power management support logic supports four device power states - On, Standby, Suspend and Off - defined for the OnNow architecture. Each power state can be achieved by software control bits. Clocks to every major functional block are controlled by a unique dynamic clock switching technique which is completely transparent to the software. By turning off the clock to the block that is idle or not used at that point, the power consumption is significantly reduced during normal operation Internal Thermal Sensor Provides ASIC die temperature without external chip. High and low notification limits can be defined to generate an interrupt and to change power state. Can be used to control a fan through PWM output critical temperature limit to protect the ASIC from damage Kontron User's Guide UGM-M72 11

12 4 Signal Descriptions 4.1 Connector Locations DVO Connector UGM Module Connector Fan Connector 4.2 DVO Connector Currently unused 4.3 Fan Connector Currently unused 4.4 UGM Module Connector The Module Receptacle is an AMP/Tyco mm pitch / 220 pin connector. Please see the latest UGM Specification for any details. Kontron User's Guide UGM-M72 12

13 4.4.1 Connector Pinout Pin Name Pin Name Pin Name Pin Name A1 GND B1 GND A56 PCIE_RX1N B56 PCIE_TX1N A2 Fan_PWM B2 Fan_OUT A57 GND B57 GND A3 LVDS_A_0N B3 LVDS_B_0N A58 PCIE_RX2P B58 PCIE_TX2P A4 LVDS_A_0P B4 LVDS_B_0P A59 PCIE_RX2N B59 PCIE_TX2N A5 GND B5 GND A60 GND B60 GND A6 LVDS_A_1N B6 LVDS_B_1N A61 PCIE_RX3P B61 PCIE_TX3P A7 LVDS_A_1P B7 LVDS_B_1P A62 PCIE_RX3N B62 PCIE_TX3N A8 GND B8 GND A63 GND B63 GND A9 LVDS_A_2N B9 LVDS_B_2N A64 PCIE_RX4P B64 PCIE_TX4P A10 LVDS_A_2P B10 LVDS_B_2P A65 PCIE_RX4N B65 PCIE_TX4N A11 GND B11 GND A66 GND B66 GND A12 FP_ENA B12 LVDS_B_CLKN A67 PCIE_RX5P B67 PCIE_TX5P A13 LVDS_A_CLKN B13 LVDS_B_CLKP A68 PCIE_RX5N B68 PCIE_TX5N A14 LVDS_A_CLKP B14 GND A69 AC/BATT# B69 RSVD A15 GND B15 BL_BRT A70 GND B70 GND A16 LVDS_A_3N B16 LVDS_B_3N A71 PCIE_RX6P B71 PCIE_TX6P A17 LVDS_A_3P B17 LVDS_B_3P A72 PCIE_RX6N B72 PCIE_TX6N A18 GND B18 GND A73 GND B73 GND A19 N.C. B19 N.C. A74 PCIE_RX7P B74 PCIE_TX7P A20 N.C. B20 N.C. A75 PCIE_RX7N B75 PCIE_TX7N A21 GND B21 GND A76 GND B76 GND A22 BL_ENA B22 TMP_FAIL# A77 PCIE_RX8P B77 PCIE_TX8P A23 TMDS_I2CLK B23 LVDS_I2CLK A78 PCIE_RX8N B78 PCIE_TX8N A24 TMDS_I2DAT B24 LVDS_I2DAT A79 Panel_EN# B79 PCIE_RST# A25 GND B25 GND A80 GND B80 GND A26 TMDS_TX2P B26 Cap_D0 A81 Capture_EN# B81 TVin_EN# A27 TMDS_TX2N B27 Cap_D1 A82 PCIE_RX9P B82 PCIE_TX9P A28 GND B28 GND A83 PCIE_RX9N B83 PCIE_TX9N A29 TMDS_TX1P B29 Cap_D2 A84 GND B84 GND A30 TMDS_TX1N B30 Cap_D3 A85 PCIE_RX10P B85 PCIE_TX10P A31 GND B31 GND A86 PCIE_RX10N B86 PCIE_TX10N A32 TMDS_TX0P B32 Cap_D4 A87 GND B87 GND A33 TMDS_TX0N B33 Cap_D5 A88 PCIE_RX11P B88 PCIE_TX11P A34 GND B34 GND A89 PCIE_RX11N B89 PCIE_TX11N A35 TMDS_CLKP B35 Cap_D6 A90 GND B90 GND A36 TMDS_CLKN B36 Cap_D7 A91 PCIE_RX12P B91 PCIE_TX12P A37 TMDS_HPD B37 GND A92 PCIE_RX12N B92 PCIE_TX12N A38 Cap_PCLK B38 TV_C A93 GND B93 GND A39 Cap_I2CLK B39 TV_Y A94 PCIE_RX13P B94 PCIE_TX13P A40 Cap_I2DAT B40 TV_CVBS A95 PCIE_RX13N B95 PCIE_TX13N A41 GND B41 GND A96 GND B96 GND A42 VGA_RED B42 VGA2_HSYNC A97 PCIE_RX14P B97 PCIE_TX14P A43 VGA_GRN B43 VGA2_VSYNC A98 PCIE_RX14N B98 PCIE_TX14N A44 VGA_BLU B44 N.C. A99 PRSNT# B99 UGM_ID A45 GND B45 N.C. A100 GND B100 GND A46 VGA_HSYNC B46 N.C. A101 PCIE_RX15P B101 PCIE_TX15P A47 VGA_VSYNC B47 N.C. A102 PCIE_RX15N B102 PCIE_TX15N A48 PCIE_CLKRQ# B48 GND A103 GND B103 GND A49 VGA_DDCCLK B49 PCIE_CK_REFP A104 VDD B104 VDD A50 VGA_DDCDAT B50 PCIE_CK_REFN A105 VDD B105 VDD A51 GND B51 GND A106 VDD B106 VDD A52 PCIE_RX0P B52 PCIE_TX0P A107 VDD B107 VDD A53 PCIE_RX0N B53 PCIE_TX0N A108 VDD B108 VDD A54 GND B54 GND A109 VDD B109 VDD A55 PCIE_RX1P B55 PCIE_TX1P A110 GND B110 GND Kontron User's Guide UGM-M72 13

14 4.4.2 PCI Express Pins PCIE_CK_REFN/P PCIE_CLK_REQ# PCIE_RST# PCIE_RX[15:0]N/P PCI Express Reference Clock Pair, 100R-terminated on UGM PCI Express Clock Request, Active Low Global PCI Express Reset, coming from Root Complex PCI Express RX Lane Pairs, Inputs into Root Complex. Capacitive coupled on UGM PCIE_TX[15:0]N/P PCI Express TX Lane Pairs, coming from Root Complex, 100Rterminated on UGM Please refer to PCI Express Specification for any signal details ( LVDS Flatpanel Signals The LVDS Signals are typically used to drive a local flatpanel. Up to 2x24-Bit panels with a max.pixelclock of 2x130MHz are supported. LVDS_A_[3:0]N/P LVDS Data Pairs, Single/Dual Link, 1st/Odd Data in Dual Pixel Mode LVDS_B_[3:0]N/P LVDS Data Pairs, DualLink, 2nd/Even Data in Dual Pixel Mode LVDS_A/B_CLKN/P LVDS Clock Pairs for Single/Dual Link LVDS_I2CLK/DAT LVDS DDC Interface, 2k2 pullups recommended Depending on the selected LVDS coding scheme the related signals carry different contents. See the following tables for details: Pin 18Bit Data 24Bit VESA Data 24Bit LDI Data LVDS_A_0N/P R0..R5, G0 R0..R5,G0 R2..R7,G2 LVDS_A_1N/P G1..G5,B0,B1 G1..G5,B0,B1 G3..G7,B2,B3 LVDS_A_2N/P B2..B5,HS,VS,DE B2..B5,HS,VS,DE LVDS_A_3N/P unused B4..B7,HS,VS,DE R6,R7,G6,G7,B6,B7 R0,R1,G0,G1,B0,B1 Data Mapping SingleLink / DualLink: 1st/Odd Pixel Pin 18Bit Data 24Bit VESA Data 24Bit LDI Data LVDS_B_0N/P R0..R5, G0 R0..R5,G0 R2..R7,G2 LVDS_B_1N/P G1..G5,B0,B1 G1..G5,B0,B1 G3..G7,B2,B3 LVDS_B_2N/P B2..B5 B2..B5 B4..B7 LVDS_B_3N/P unused Flatpanel Power Management Signals R6,R7,G6,G7,B6,B7 R0,R1,G0,G1,B0,B1 Data Mapping Unused / DualLink: 2nd/Even Pixel These signals may be used to control power and brightness of a flatpanel subsystem. LVDS_BKLT_CTRL Backlight Brightness Control, PWM, Active High LVDS_BKLT_EN LVDS_VDD_EN Backlight Power Enable, Active High Panel Power Enable, Active High These signals are 3.3V I/O Kontron User's Guide UGM-M72 14

15 4.4.5 TMDS Panel Interface The TMDS Signals are either used for DVI or HDMI. UGM-M72 supports one single link TMDS port at a bandwidth of 165MHz. TMDS_TX[2:0]N/P TMDS Data Pairs 2..0 TMDS_CLKN/P TMDS_I2CLK/DAT TMDS_HPD CRT 1 Signals TMDS Clock Pair DVI/HDMI DDC Channel Dedicated Hot Plug Detect for TMDS Interface The DDC channel and the HPD signal are 3.3V I/O The CRT 1 signals are derived from a triple 10-Bit DAC with a max.pixelclock of 400MHz. The DAC outputs are designed to drive a 37.5R load. This allows for double termination of the CRT's 75R impedance with onboard 75R load to improve signal quality. VGA_RED VGA_GRN VGA_BLU VGA_HSYNC VGA_VSYNC VGA_I2CLK/DAT Red DAC Output Green DAC Output Blue DAC Output Horizontal Sync, requires external TTL Buffer Vertical Sync, requires external TTL Buffer CRT DDC Channel Syncs and DDC channel are 3.3V I/O TV Out Interface / 2nd CRT (Optional) The TV Out signals are also derived from a triple 10-Bit DAC, supporting composite, s-video and component output with a max.pixelclock of 400MHz. Alternatively these pins may be used for secondary CRT connection. The DAC outputs are designed to drive a 37.5R load. This allows for double termination of the external device's 75R impedance with onboard 75R load to improve signal quality. TV_CVBS or VGA2_BLU TV_C or VGA2_RED TV_Y or VGA2_GREEN VGA2_HSYNC VGA2_VSYNC Composite Signal or Pb for Component Out or 2nd CRT Blue DAC Output Chroma Signal for S-Video Out or Pr Signal for Component Out or 2nd CRT Red DAC Output Luma Signal for S-Video Out or Y Signal for Component Out or 2nd CRT Green DAC Output 2nd CRT Horizontal Sync, requires external TTL Buffer 2nd CRT Vertical Sync, requires external TTL Buffer Kontron User's Guide UGM-M72 15

16 4.4.8 ITU-656 Capture Port UGM-M72 supports video capture using an ITU-656 compliant 8-Bit interface Cap_D[7:0] Cap_PCLK Cap_I2CLK/DAT 8-Bit Video Capture Data Video Capture Pixel Clock I2C Configuration Interface These signals are 3.3V I/O Thermal- / Power-Management Signals TMP_FAIL# Open Collector Signal, active (low) if die exceeds 105 Fan_PWM Fan_OUT AC/BATT# UGM Configuration External PWM Source to control Fan, currently unused Fan Speed Signal, directly coming from Fan Connector may be used to control power savings, High=AC Powered These static signals are used to identify the UGM's capabilities to the system. Capture_EN# pulled low on UGM - Video Capture enabled Panel_EN# TVin_EN# PRSNT# UGM_ID Power Supply pulled low on UGM - LVDS interface enabled pulled high on UGM - TV-In disabled pulled low on UGM - Basic Presence signal pulled low on UGM - Graphics Board GND VDD GND Pins Power Supply Pins, 12V..22V Kontron User's Guide UGM-M72 16

17 UGM Connector Summary Signal Name Type Uref Load Description Remarks AC/BATT# TTL I 3.3V High = AC Powered Cap_D[7:0] TTL I/O 3.3V ITU-656 Capture Data Cap_I2CLK TTL O 3.3V ITU-656 Control Clock 2k2 pullup recommended Cap_I2DAT TTL I/O 3.3V ITU-656 Control Data 2k2 pullup recommended Cap_PCLK TTL O 3.3V ITU-656 Capture Clock Capture_EN# Static 0V Capture enabled 2k2 pulldown on module Fan_OUT TTL O var. Fan Speed Signal unused Fan_PWM PWM I var. external Fan PWM ctrl. unused GND Power GND Power GND LVDS_A_[3:0]N/P LVDS O (1.8V) 100R First-/Single-Pixel Data LVDS_A_CLKN/P LVDS O (1.8V) 100R First-/Single-Pixel Clock LVDS_B_[3:0]N/P LVDS O (1.8V) 100R Second-Pixel Data LVDS_B_CLKN/P LVDS O (1.8V) 100R Second-Pixel Clock LVDS_BKLT_CTRL PWM O 3.3V Backlight Brightn.Ctrl. LVDS_BKLT_EN TTL O 3.3V Backlight Enable e.g. controls MOSFET LVDS_I2CLK TTL O 3.3V FP DDC Clock 2k2 pullup recommended LVDS_I2DAT TTL I/O 3.3V FP DDC Data 2k2 pullup recommended LVDS_VDD_EN TTL O 3.3V Panel Power Enable e.g. controls MOSFET Panel_EN# Static 0V LVDS enabled 2k2 pulldown on module PCIE_CK_REFN/P LVDS I 0.7V 100R PCI-E Reference Clock PCIE_CLK_REQ# TTL O 3.3V PCI-E Clock Request. PCIE_RST# TTL I 3.3V PCI-E Reset PCIE_RX[15:0]N/P LVDS O 0.4V 100R RX Lanes, to Root PCIE_TX[15:0]N/P LVDS I 0.4V 100R TX Lanes, from Root PRSNT# Static 0V UGM Presence Det. 2k2 pulldown on module TMDS_CLKN/P TMDS O (1.8V) 100R DVI/HDMI Clock TMDS_HPD TTL I 3.3V DVI/HDMI Hot Plug Det. TMDS_I2CLK TTL O 3.3V DVI/HDMI DDC Clock 2k2 pullup recommended TMDS_I2DAT TTL I/O 3.3V DVI/HDMI DDC Data 2k2 pullup recommended TMDS_TX[2:0]N/P TMDS O (1.8V) 100R DVI/HDMI Data TMP_FAIL# TTL O 3.3V Low if die exceeds 105C 10k pullup recommended TV_C A O 1V 37.5R TV Chroma Signal 75R double termination TV_CVBS A O 1V 37.5R TV Composite Signal 75R double termination TV_Y A O 1V 37.5R TV Luma Signal 75R double termination TVin_EN# Static 3.3V TV in disabled 2k2 pullup on module UGM_ID Static 0V UGM ID Graphics Board 2k2 pulldown on module VDD Power 12-22V Power Supply VGA_BLU A O 0.75V 37.5R CRT Blue Signal 75R double termination VGA_GRN A O 0.75V 37.5R CRT Green Signal 75R double termination VGA_HSYNC TTL O 3.3V CRT Horizontal Sync. VGA_I2CLK TTL O 3.3V CRT DDC Clock 2k2 pullup recommended VGA_I2DAT TTL I/O 3.3V CRT DDC Data 2k2 pullup recommended VGA_RED A O 0.75V 37.5R CRT Red Signal 75R double termination VGA_VSYNC TTL O 3.3V CRT Vertical Sync. Table sorted by signal name Kontron User's Guide UGM-M72 17

18 5 Specifications 5.1 Electrical Specifications Supply Voltage...12V to 22V DC +/-5% Voltage Ripple...max.250mV peak to peak 0 20 MHz Power Consumption...typ.6W to 15W (application/memory dependant) 5.2 Environmental Specifications Temperature (operating)...0 to +60 Deg.C (non operating) to +85 Deg.C Humidity (operating)...10% to 90% (non condensing) (non operating)...5% to 95% (non condensing) 5.3 Mechanical Specifications Dimensions mm x 84.0 mm All Mounting Holes...2.5mm Diameter Kontron User's Guide UGM-M72 18

19 6 Known Restrictions No. PCB Revision Description 1 UGM1L110 PCI Express TX and RX group swapped --This Rev. does not work on standard UGM connectors!! -- Workaround: Use in combination with UGM Riser Rev Solution: Was fixed in PCB Revision V Revision History Rev. Date Editor Changes A.Kaudel Initial Release A.Kaudel - DVO- and Fan-Connectors set to unused - 2nd CRT added - Restrictions updatet - some formating issues Kontron User's Guide UGM-M72 19