2 Type 2 3 Type 3 4 Type 4 5 Type ma 55LA LA LA mA 70LA LA LA-6470

Transcription

1

2 Redefining value with outstanding performance ECOFORM OUTDOOR SITE & AREA PHILIPS GARDCO, LED SITE & AREA LUMINAIRE, ECOFORM The Philips Gardco EcoForm combines economy with performance in an LED area luminaire. Capable of delivering up to 20,000 lumens or more in a compact, low profile LED luminaire, EcoForm offers a new level of customer value. EcoForm features an innovative retrofit arm kit, simplifying site conversions to LED by eliminating the need to drill additional holes in most existing poles. Integral control systems available for further energy savings. Ordering guide Project: Location: Catalog No: Fixture Type: Mfg: Notes: Qty: Prefix Mounting Optics LED Array & LED Wattage LED Selection Voltage Finish Options ECF ECF-DIM ECF-APD 1 ECF-MR50 2 EcoForm Standard Luminaire EcoForm with 0-10V Dimming EcoForm with Auto Profile Dimming EcoForm with Motion Response at 50% low Pole mounted sensor ECF-APD-MRO 2 EcoForm with Auto Profile Dimming and Motion Response Override Pole mounted sensor ECF-MRI 2,4 EcoForm with Motion Response at 50% low Luminaire mounted sensor ECF-APD-MRI 2,4 EcoForm with Auto Profile Dimming with Motion Response Override Luminaire mounted sensor 1 Single 2 2@180 2@90 2@90 3 3@90 3@120 3@ @90 WS Wall mount including Surface conduit Rear entry permitted MA Mast Arm Fitter (requires 2-3/8" O.D. Mast Arm) 2 Type 2 3 Type 3 4 Type 4 5 Type ma 55LA LA LA mA 70LA LA LA mA 105LA-321A 1 160LA-481A 215LA-641A CW 5,700K 70 CRI NW 4,000K 70 CRI WW 3 3,000K 70 CRI UNV V HVU V BRP Bronze Paint BLP Black Paint WP White Paint NP OC SC Natural Paint Optional Color Specify optional color or RAL ex: OC-LGP or OC-RAL7024. Special Color Specify. Must supply color chip. Requires factory quote. TL TB 4 IS 5 LF 6,10 LFC 6,10 Tool-Less entry & driver removal hardware Terminal Block Internal Shield Line Fusing Line Fusing for Canada PCR Photocell Receptacle Only PC 6,7,10 Receptacle with Photocell PCB 6,7,10 Photocell Button RAM Retrofit Arm Mount Kit PTF2 8 Pole Top Fitter for 2-3/8"-3" Tenon PTF3 8 Pole Top Fitter for 3"-3.5" Tenon PTF4 8 Pole Top Fitter for 3.5"-4" Tenon RPA 9 Round Pole Adaptor for 3" to 3.9" OD BD Bird Deterrant (field installed only) 1. Available in 120V thru 277V only. 2. MR50 and APD-MRO luminaires require one motion sensor per pole, ordered separately. See Accessories on page 2. Available 120V or 277V only. 3. Contact factory for lead times on warm white. 4. ECF-MRI requires outboarded sensor when used with Terminal Block (TB) option. 5. Not available with Type 5 optics. 6. Voltage must be specified. 7. Not available in 480V. 8. Not available in No adaptor required for 4" round poles. RPAs provided with Black Paint standard. 10. Not available with UNV ( V). Untitled-6 03/14 page 1 of 6

3 ECOFORM OUTDOOR SITE & AREA Accessories (Order Separately) FS1R-100 MR hand held programmer (For use with 'MRI' motion response when field programming is required). If desired, only one is needed per job. MS-A-120V 120V input - Motion Sensor for MR50 or APD-MRO MS-A-277V 277V input - Motion Sensor for MR50 or APD-MRO LED Wattage and Lumen Values - Standard EcoForm Luminaire Initial Lumens 12 Order Code (standard units) Array Quantity Total LEDs LED Current (ma) Average System Watts 11 LED Selection 2 Type 2 3 Type 3 4 Type 4 5 Type 5 55LA NW 5,994 (s) 5,895 (s) 5,823 (s) 5,588 (s) 75LA NW 8,899 (s) 8,753 (s) 8,646 (s) 8,297 (s) 100LA NW 11,896 (s) 11,700 11,558 11,091 70LA NW 7,385 (s) 7,576 (s) 7,293 (s) 7,068 (s) 105LA NW 10,965 (s) 11,249 (s) 10,828 (s) 10,494 (s) 135LA NW 14,657 (s) 15,037 14,475 (s) 14, LA-321A NW 10,199 (s) 10,458 10,072 (s) 9, LA-481A NW 15,144 (s) 15,565 14,955 (s) 14, LA-641A NW 20,243 20,252 19,991 19, System input wattage may vary based on input voltage, by up to +/- 10%, and based on manufacturer forward voltage, by up to +/- 8%. 12. Lumen values based on photometric tests performed in compliance with IESNA LM-79. (s). Data is scaled based on tests of similar, but not identical, luminaires. EcoForm Drill Template (Standard Arm Mount) cm Ø cm Ø cm cm cm Note: For reference only. Drawing not to scale. Untitled-6 03/14 page 2 of 6

4 ECOFORM OUTDOOR SITE & AREA Dimensions - Standard EcoForm Luminaire Top View Side View End View cm cm cm cm cm cm cm EPA (Ft 2/M2) cm Single Twin (2@180) 3/4@ / / / Approximate Luminaire Weight: 20 Lbs (9.07 Kg) Dimensions - EcoForm with Retrofit Arm Mount (RAM) Top View Side View End View cm cm cm cm cm cm cm EPA (Ft 2/M2) Single Twin (2@180) 3/4@ / / / Approximate Luminaire Weight: 21 Lbs (9.53 Kg) Dimensions - EcoForm with Mast Arm Fitter (MA) Top View Side View End View cm 8.4 cm cm cm 8.38 cm cm cm cm cm EPA (Ft 2/M2) Approximate Luminaire Weight: 21.5 Lbs (9.77 Kg) Single 0.51 / Dimensions - EcoForm with Wall Mount (WS) Top View Side View End View cm cm cm cm cm cm 16.5 cm cm cm cm cm Untitled-6 03/14 page 3 of 6 Approximate Luminaire Weight: Lbs (10.6 Kg)

5 ECOFORM OUTDOOR SITE & AREA Luminaire Configuration Information ECF Philips Gardco EcoForm LED standard luminaire providing constant wattage and constant light output when power to the luminaire is energized. ECF-DIM Philips Gardco EcoForm LED luminaire provided with 0-10V dimming for connection to a control system provided by others. ECF-APD Philips Gardco EcoForm LED luminaire with Automatic Profile Dimming. Luminaire is provided with a Philips DynaDimmer module, programmed to go to 50% power, 50% light output two (2) hours prior to night time mid-point and remain at 50% for six (6) hours after night time mid-point. Mid-point is continuously recalculated by the Philips DynaDimmer module based on the average mid-point of the last two full night cycles. Short duration cycles, and power interruptions are ignored and do not affect the determination of mid-point. ECF-APD is available in 120V through 277V input only. ECF-APD Dimming Profile: 2 Hours 6 Hours 100% 100% 50% 50% Power On ECF-MR50 Philips Gardco EcoForm LED luminaire with motion response, providing a 50% power reduction on low and a commensurate reduction in light output. The power and light output reduction is accomplished utilizing the Philips DynaDimmer module, programmed for a constant 50% power. Power supplied by the motion sensor connected to the override line on the DynaDimmer takes the luminaire to high setting, 100% power and light output, when motion is detected. The luminaire remains on high until no motion is detected for the motion sensor duration period, after which the luminaire returns to low. Duration period is factory set at 15 minutes, and is field adjustable from 5 minutes up to 15 minutes. ECF-MR50 is available in 120V through 277V input only to the luminaire. Motion sensors require single voltage 120V or 277V input. The Area PIR motion sensor is the WattStopper EW W (120V Input - MSA- 120V) or the WattStopper EW W (277V Input - MSA-277V.) One motion sensor per pole is required and is ordered separately. Area sensors require single voltage 120V or 277V input. Black, 120V OR 277V Input White - Neutral Mid Point Sensor Power Off Red Connects to Override Input (Orange) Line of DynaDimmer The area motion detector provides coverage equal to up to 6 times the sensor height above ground, 270 from the front-center of the sensor. Area PIR Motion Sensor Coverage Pattern: Motion response requires that the pole include an additional hand hole 15 feet above the pole base, normally oriented 180 to the standard hand hole. For Philips Gardco poles, order the pole with the Motion Sensor Mounting (MSM) option which includes the hand hole and a special hand hole cover plate for the sensor with a 1/2" NPT receptacle centered on the hand hole cover plate into which the motion sensor mounts. Once the motion sensor is connected to the hand hole cover plate, then wiring connections are completed in the pole. The plate (complete with motion sensor attached and wired) is then mounted to the hand hole. If poles are supplied by others, the customer is responsible for providing suitable mounting accommodations for the motion sensor in the pole. ECF-APD-MRO Height 8ft (2.4m) Mounting to a Philips Gardco Pole Wiring in Pole 270 Front Coverage Distances are approximate. H= Height Above 9.5ft (3m) 1H 25ft (8m) 52.5ft (16m) Philips Gardco EcoForm LED luminaire with Automatic Profile Dimming, with Motion Response Override. The ECF-APD-MRO combines the benefits of both automatic profile dimming and motion response, using the Philips DynaDimmer module. The luminaire will dim to 50% power, 50% light output, per the dimming profile shown for the ECF-APD. If motion is detected during the time that the luminaire is operating at 50%, the luminaire returns to 100% power and light output. The luminaire remains on high until no motion is detected for the duration period, after which the luminaire returns to low. Duration period is factory set at 15 minutes, and is field adjustable from 5 minutes up to 15 minutes. NOTES: ECF-APD-MRO is available in 120V through 277V input only to luminaire. The motion sensor requires either 120V or 277V input to the motion sensor. 3H 6H Cover Plate with 1/2" NPT Coupling (supplied with pole) Motion Sensor Additional Hand Hole 15' Above Pole Base (oriented 180 to the standard hand hole) Attach Motion Sensor to Cover Plate coupling, Complete Wiring in Pole and Attach Cover Plate to Hand Hole The ECF-APD-MRO has the same pole requirements and utilizes the same motion sensors as the ECF-MR50. The motion sensor mounts and wires identically as well. The ECF-APD-MRO utilizes the identical dimming profile as shown for the ECF-APD. By combining the benefits of automatic profile dimming and motion response, the ECF-APD-MRO assures maximum energy savings, and insures that adequate light is present if motion is detected. All motion sensors utilized consume 0.0 watts in the off state. Untitled-6 03/14 page 4 of 6

6 ECOFORM OUTDOOR SITE & AREA Luminaire Configuration Information (Continued) ECF-MRI Luminaires with Motion Response include a LED driver and an integral programmable motion sensor. The motion sensor is set to a constant 50%. When motion is detected, the luminaire goes to 100%. The luminaire remains on high until no motion is detected for the motion sensor duration period, after which the luminaire returns to low. Duration period is factory set at 5 minutes. Available with 120V or 277V only. Luminaires include a passive infrared (PIR) motion sensor, WattStopper FSP-211 equipped with an FSP-L3 lens, capable of detecting motion within 20 feet of the sensor, 180 around the luminaire, when placed at a 20 foot mounting height, or mounted on a wall. Available in 120V or 277V input only. Motion sensor off state power is 0.0 watts. The approximate motion sensor coverage pattern is as shown below. FS1R-100 Wireless Remote Programming Tool The FS1R-100 Remote Programming Tool accessory permits adjustment of ECF-MRI and ECF-APD-MRI sensor settings, including duration and dimming level on low, without the need to connect any wires to the luminaire. The FS1R-100 Wireless IR Programming Tool is a handheld tool for setup and testing of WattStopper FSP-211. It provides wireless access to the FSP-211 sensors for setup and parameter changes. The FS1R-100 display shows menus and prompts to lead you through each process. The navigation pad provides a familiar way to navigate through the customization fields. Side Coverage Pattern Top Coverage Pattern Within a certain mounting height of the sensor, the FS1R-100 allows modification of the system without requiring ladders or tools simply with a touch of a few buttons. Distances are approximate. H = Height above ground. The FS1R-100 IR transceiver allows bi-directional communication between the FSP-211 and the FS1R-100 programming tool. Simple menu screens let you see the current status of the system and make changes. It can change FSP-211 sensor parameters such as high/low mode, sensitivity, time delay, cut off and more. With the FS1R-100 you can also establish and store FSP-211 parameter profiles. 2H 1H 2H The FS1R-100 operates on three standard 1.5V AAA Alkaline batteries or three rechargeable AAA NiMH batteries. The battery status displays in the upper right corner of the display. Three bars next to BAT= indicates a full battery charge. A warning appears on the display when the battery level falls below a minimum acceptable level. To conserve battery power, the FS1R-100 automatically shuts off 10 minutes after the last key press. ECF-APD- MRI Luminaires with Automatic Profile Dimming and Motion Response Override combine the benefits of both automatic profile dimming and motion response. APD-MRI luminaires utilize Philips DynaDimmer. The luminaire will dim to 50% power, 50% light output, per the dimming profile shown for APD luminaires (see page 4). If motion is detected during the time that the luminaire is operating at 50%, the luminaire goes to 100% power and light output. The luminaire remains on high until no motion is detected for the duration period, after which the luminaire returns to low. Duration period is factory set at 5 minutes. APD-MRI luminaires are available with 120V or 277V input voltages only. APD-MRI luminaires use the identical motion sensor as MRI luminaires. See motion sensor details for ECF-MRI. You navigate from one field to another using (up) or (down) arrow keys. The active field is indicated by flashing (alternates between yellow text on black background and black text on yellow background.) Once active, use the Select button to move to a menu or function within the active field. Value fields are used to adjust parameter settings. They are shown in lessthan/greater-than symbols: <value>. Once active, change them using (left) and (right) arrow keys. In general the up key increments and the down key decrements a value. Selections wrap-around if you continue to press the key beyond maximum or minimum values. Moving away from the value field overwrites the original value. The Home button takes you to the main menu. The Back button can be thought of as an undo function. It takes you back one screen. Changes that were in process prior to pressing the key are lost.more information on the FS1R-100 Remote Programming Tool is available at wattstopper.com. Power On/Off FSP-201 FSP-211 FD-101 FD-301 BAT= Back Left Down Home/Main Menu Up Right/Next Select Untitled-6 03/14 page 5 of 6

7 ECOFORM OUTDOOR SITE & AREA Specifications General Description The Philips Gardco EcoForm combines economy with performance in an LED area luminaire. Capable of delivering up to 20,000 lumens or more in a compact, low profile LED luminaire, EcoForm offers a new level of customer value. Integral control systems including motion response are available for further energy savings during off peak hours. EcoForm is also part of the Philips Solar Solution. See Solar Specification Sheet for details. Housing One piece die cast aluminum housing with integral arm and separate,self retained hinged, one piece die cast door frame. IP Rating LED light engine rated IP66. Vibration Resistance EcoForm with Standard Arm carries a 3G vibration rating that conforms to standards set forth by ANSI C Testing includes vibration to 3G acceleration in three axes, all performed on the same luminaire. Electrical Driver efficiency (>90% standard) V available (restrictions apply). Open/short circuit protection. Optional 0-10V dimming to 10% power. RoHS compliant. Surge protector standard. 10KA per ANSI/ IEEE C LED Board and Array 32, 48, or 64 LEDs. Color temperatures: 3000K, 4000K, 5700K +/- 250K. Minimum CRI of 70. Aluminum metal clad board. RoHS compliant. Energy Saving Benefits System efficacy up to 95 lms/w with significant energy savings over Pulse Start Metal Halide luminaires. Optional control options provide added energy savings during unoccupied periods. Motion Sensors ECF-MR50, ECF-APD-MRO, ECF-MRI, ECF-APD- MRI luminaires may be specified for additional energy savings during unoccupied periods. See pages 4-6 for complete details. LED Thermal Management The housing design allows the one piece housing to provide excellent thermal management critical to long LED system life. Optical Systems Type 2, 3, 4, and 5 distributions available. Internal Shield option mounts to LED optics and is available with Type 2, 3, and 4 distributions to control backlight. Mounting Standard luminaire arm mounts to 4" round poles. Square pole adapter included with every luminaire. Round Pole Adapter (RPA) required for 3-3.9" poles. Retrofit Arm Mount EcoForm features an innovative retrofit arm kit. When specified with the retrofit arm (RAM) option, EcoForm seamlessly simplifies site conversions to LED by eliminating the need for additional pole drilling on most existing poles. RAM will be boxed separately cm cm Listings ETL/cETL listed to the UL 1598 standard, suitable for Wet Locations. Suitable for use in ambients from -30 to 40 C (-22 to 104 F). The quality systems of this facility have been registered by UL to the ISO 9001 series standards. All EcoForm luminaires equipped with NW and CW are DesignLights Consortium qualified. Finish Each standard color luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard colors include bronze (BRP), black (BLP), white (WP), and natural aluminum (NP). Consult factory for specs on optional or custom colors. Warranty EcoForm luminaires feature a 5 year limited warranty. Philips Gardco LED luminaires with LED arrays feature a 5 year limited warranty covering the LED arrays. LED Drivers also carry a 5 year limited warranty. Motion sensors are covered by warranty for 5 years by the motion sensor manufacturer. LED Performance: Ambient Temperature C PREDICTED LUMEN DEPRECIATION DATA 13 Driver ma Calculated L 70 Lumen Maintenance % L Hours 13,14 70 Per TM-21 60,000 hours Up to 40 C Up to 1050 ma > 350,000 Hours > 60,000 Hours 97% 13. Predicted performance derived from LED manufacturer s data and engineering design estimates, based on IESNA LM-80 methodology. Actual experience may vary due to field application conditions. 14. L 70 is the predicted time when LED performance depreciates to 70% of initial lumen output. 15. Calculated per IESNA TM Published L 70 hours limited to 6 times actual LED test hours. Untitled-6 03/14 page 6 of 6 Philips Lighting Company 200 Franklin Square Drive Somerset, NJ Phone: Philips Lighting Company 281 Hillmount Road Markham ON, Canada L6C 2S3 Phone:

8 Job: Type: Notes: Page 1 of 3 Bollard LED Round Full Cutoff Bollard BR840 Series, Including Motion Response The Philips Gardco LED Bollard family features the round full cutoff bollard, the BR840 series. This sleek series features LEDs concealed below cast louvers to provide down lighting for landscape and pathway applications. The BR840 series features 4" diameter extruded aluminum shafts. Available mountings include the standard shaft, with a welded cast base mounted firmly to anchor bolts. The BR840 series also is available with a galvanized steel base tenon reinforced shaft (BR842) for applications requiring additional support, such as schools. BR840 series bollards provide full cutoff performance. PREFIX HEIGHT LED CONTROL LED SELECTION LIGHTED COVERAGE / LED WATTAGE VOLTAGE FINISH OPTIONS Enter the order code into the appropriate box above. Note: Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. PREFIX BR840 Standard Shaft 42" 36" 30" BR841 Head Only 7.1" BR842 School Bollard Reinforced Shaft with Galvanized Steel Tenon HEIGHT 42" 36" 30" led control CWL DIM MR Constant Wattage Full Light Output Full wattage and light output only. 0-10V Dimming Dimming controls by others. The dimming driver utilized permits dimming control via a potentiometer (by others) or via 0-10V control (by others.) Consult installation instructions for more information. Motion Response Featuring two (2) integral Passive Infrared (PIR) sensors. In the absence of motion, luminares operate at 20% of normal power and light output (80% dimmed.) See page 3 for more information on Motion Response luminaires. LED SELECTION CW 5,700 K, 75CRI NW 4,000 K, 75CRI WW 3,000 K, 75CRI lighted coverage / LED Wattage 360 lighted louvers - 14 LEDs watts at 225mA watts at 350mA watts at 500mA Note: A variation of LED wattage (+/- 8%) may occur due to LED manufacturer s forward volt specification and ambient temperature. voltage UNIV 120V through 277V, 50hz to 60hz input. finish 180 lighted louvers - 7 LEDs 1,2 (Provides reduced backside light.) watts at 450mA watts at 700mA achieved by populating half of LEDs distributions include an internal house side shield to limit the amount of backlight. OPTIONS BRP BLP WP NP Bronze Paint Black Paint White Paint Natural Aluminum Paint OC SC Optional Color Paint Specify RAL designation as ex: OC-RAL7024. Special Color Paint Specify. Must supply color chip. PCB 3 SPR Button Photocontrol Surge Protection for 120V through 277V Input meeting ANSI C Not available in BR Clovis Barker Road, San Marcos, TX (800) (512) FAX: (512) sitelighting.com 2013 Koninklijke Philips Electronics N.V. All Rights Reserved. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program. G /0113

9 Page 2 of 3 Bollard LED Round Full Cutoff Bollard BR840 Series, Including Motion Response DIMENSIONS 8.3" cm BR840 BR842 School Bollard with Steel Base Tenon BR841 Head Only B 7.1" cm PIR Motion Sensor - Motion Response Luminaires Only. Approximate diameter 0.8" (2cm.) Height 11 gauge Steel Base Tenon 2.25" (5.715 cm) Square Ground Lug 2.75" Bolt Circle (6.985 cm) 0.5" (1.27cm) or.75" (1.905cm) Conduit (by others) 2.75" (6.985 cm) Bolt Circle BR841 mounts to a concrete structure via four (4) 3/8" #16 hex head bolts inserted into threaded concrete inserts (provided by others.) 2.75" (6.985 cm) Bolt Circle 1.375" cm 4" cm 1.75" Dia. Conduit Opening 1.945" cm 45 NOTE: Factory supplied template must be used when setting anchor bolts. Philips Gardco will not honor any claim for incorrect anchorage placement from failure to use factory supplied templates Clovis Barker Road, San Marcos, TX (800) (512) FAX: (512) sitelighting.com 2013 Koninklijke Philips Electronics N.V. All Rights Reserved. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program. G /0113

10 Page 3 of 3 Bollard LED Round Full Cutoff Bollard BR840 Series, Including Motion Response SPECIFICATIONS UPPER HOUSING: Die cast aluminum upper housing featuring shielding louvers to provide down light. LOWER HOUSING: BR840 : The lower housing assembly consists of a.140" wall by 4" diameter high strength 6063-T6 extruded aluminum section incorporating a flush, weather-tight gasketed hand hole cover. BR41 : Louver head assembly is suitable for attachment to architectural elements (by others). BR842 : The lower housing assembly consists of a.140" wall by 4" diameter high strength 6063-T6 extruded aluminum section, incorporating a flush, weather-tight gasketed hand hole cover, for placement over the galvanized steel tenon support structure. Tenon support structure is made from a.12" thick wall, 11 gauge steel, 2.25" square tube, welded to top and bottom round steel support plates. The steel tenon support structure includes an opening aligned with the aluminum shaft hand hole to permit wiring. The entire steel tenon support structure is hot dipped galvanized after fabrication. LED PERFORMANCE: Ambient Temperature C 25 C 40 C OPTICAL SYSTEM: Philips Gardco LED Bollards feature advanced Philips Gardco LED technology, assuring maxmimized light output. LED arrays are replaceable. ANCHORAGE: PREDICTED LUMEN DEPRECIATION DATA 4 Driver ma L 70 Hours , , / , , , , / , , Predicted performance derived from LED manufacturer s data and engineering design estimates, based on IESNA LM-80 methodology. Actual experience may vary due to field application conditions. 5. L 70 is the predicted time when LED performance depreciates to 70% of initial lumen output. BR840: Base assembly consists of an internal welded cast ring section that provides for mounting to the foundation with four (4) 3/8" X 8" X 1½" anchor bolts on a 2¾" bolt circle. BR841: The luminaire head mounts to a concrete structure utilizing four (4) 3/8" #16 hex head bolts inserted into threaded concrete inserts (provided by others) on a 2¾" bolt circle. BR842: A high strength steel mounting tenon, hot-dip galvanized after fabrication, is secured to the concrete footing with (4) 3/8" x 8" x 1 1/2" anchor bolts on a 2¾" bolt circle. IP RATING: IP66 is the rating for the optical compartment. ELECTRICAL: The LED power supply is located within the bollard head. Bollards accept from 120 Volts through 277 Volts, 50hz to 60 hz, input. supply. The LED driver is located in the upper dome. LED drivers are replaceable. LEDs provided as specified. Power factor is not less than 90%. Luminaires consume 0.0 watts in the off state. MOTION RESPONSE LUMINAIRES: Each Motion Response (MR) luminaire includes two (2) Panasonic EKMB Passive Infrared (PIR) sensors to detect motion. When motion is not detected for a 5 minute period, luminaires automatically dim to 20% power and light, gradually over a 2 minute period. Once Motion is detected, luminaires immediately ramp to full power and light output until motion is not detected for a 5 minute period. PIR sensors are able to detect motion in the approximate patterns shown below: Top View Bollard 39' / 12m Maximum Detection Area ~100 Note: Motion sensors rely on specific zonal crossings to detect motion. It is possible for a person to directly approach the bollard motion sensor without crossing between zones until 15 feet from the motion sensor. The actual motion detection distance may vary based on specific application characteristics. LUMINAIRE FINISH: Each luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured textured powdercoat finish LABELS: All luminaires bear UL or CUL (where applicable) Wet Location labels. WARRANTY: Philips Gardco luminaires feature a 5 year limited warranty. Philips Gardco LED luminaires with LED arrays or modules feature a 5 year limited warranty covering the LED arrays or modules. LED drivers carry a 5 year limited warranty. See Warranty Information on for complete details and exclusions. FULL Cutoff performance: Full cutoff performance means a luminaire distribution where zero candela intensity occurs at an angle at or above 90 above nadir. Additionally, the candela per 1000 lamp lumens does not numerically exceed 100 (10 percent) at a vertical angle of 80 above nadir. This applies to all lateral angles around the luminaire Clovis Barker Road, San Marcos, TX (800) (512) FAX: (512) sitelighting.com 2013 Koninklijke Philips Electronics N.V. All Rights Reserved. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program. G /0113

11 Maximized efficiency, modular design, ultimate savings. PHILIPS GARDCO, LED PARKING GARAGE & UNDER CANOPY, G3 G3 LED PARKING GARAGE & CANOPY G3 Single LED Array G3 Dual LED Array The Philips Gardco G3 parking garage luminaire combines excellent performance with value, providing one of the most energy efficient lighting solutions for the energy and budget conscious. A complete selection of optical systems are available, including a concentrated downlight for use at entrances or at higher mounting heights. G3 luminaires are available with dimming, as well as motion response technology to expand potential energy savings. The G3 is also available with the LimeLight Wireless Lighting Control System. Project: Location: Catalog No: Fixture Type: Mfg: Notes: Qty: Ordering guide - Made to Order Luminaires example: G LA-1670-NW-UNIV-NP-QDM Prefix Distribution LED Array & LED Wattage LED Type Voltage Finish Options NP G3 G3-DIM G3 LED Standard Unit G3 with 0-10V Dimming G3-MR 1,2 G3 with Motion Response G3-MRCP 1,2 G3 with Motion Response Factory Programming G3-DCC 3,4 G3 with Dual Circuit Control (700 ma only) G3-RC 4,5 G3 with LimeLight wireless controls G3-EM 4,6,7 G3 with Emergency Battery Pack G3-EMRC 4,5,6,7 G3 with LimeLight wireless controls and Emergency Battery Pack 5 Type 5 Symmetrical 5DL Type 5 Diffuse Lens 3 Type 3 Asymmetrical 1R Type 1R Rectangular CD Concentrated Downlight 700 ma Driver 1-38LA LED Array, 38W 2-73LA LED Arrays, 73W 3-104LA LED Arrays, 104W 4-137LA LED Arrays, 137W 1050 ma Driver 1-55LA-161A 4 1 LED Array, 55W 2-106LA-321A 4 2 LED Arrays, 106W CW 5700 K 75 CRI NW 4000 K 75 CRI WW K 75 CRI UNIV V HVU V NP Natural Aluminum Paint (Standard) BRP* Bronze BLP* Black WP* White * these finishes available at an added cost F 9,15 Fusing PCB 9 Photocontrol Button QDM 12 Driver Quick Disconnect Module BX 10 Bird Excluding Shroud (field installed, PB-NP pendant mount only.) BXS 14 Bird Excluding Shroud (factory installed, for Standard Surface Mount Only) PB-NP 10 Balanced J-box for Pendant Mount (natural paint) 1. Only available in 120 or 277V. 2. See page 5 for more information on motion sensor provided. 3. Available with luminaires featuring dual LED arrays only. 4. Only available in 120 through 277V. 5. G3-RC luminaires must be configured and quoted by factory prior to ordering. G3-RC luminaires rated to 40 C. 6. Available with 38LA single LED array luminaire only. Accessories (Order Separately) FS1R MR hand held programmer (For use with 'MR' motion response when field programming is required). If desired, only one is needed per job. 7. G3-EM configuration not available for use in Canada. 8. Consult factory. Warm White may increase lead time through 277V Only. Specify actual input voltage. 10. BX bird excluding shroud is for PB-NP pendant mount only. Field installed and requires 12 minimum pendant length. Pendant by others. 11. For use with MR motion response when field programming is required. If desired, only one programmer is needed per job. 12. Not available with 350 or 530mA drive currents V, 480V, and HVU not available with 1-38LA-1670, 1-55LA-161A, and 2-106LA-321A configurations. 14. BXS Option not available with 104LA or 137LA. 15. Fusing not available with G3-DCC, G3-EM, or G3-EMRC. G /13 page 1 of 5

12 Ordering guide - Stocked Luminaires G3 LED PARKING GARAGE & CANOPY Stock Prefix Distribution LED Array & LED Wattage LED Type Voltage Finish STK UNIV NP Constant Wattage, Full Light Output STK-G LA-161A-NW-UNIV-NP STK-G LA-161A-CW-UNIV-NP STK-G VAR-NW-UNIV-NP 16,18 STK-G VAR-CW-UNIV-NP 16,18 Motion Response 15 STK-G3-MR LA-161A-NW-120/277-NP 17 STK-G3-MR LA-161A-CW-120/277-NP Variable Driver Wattage The chart below lists the LED wattage with the different drive currents that are available. Cat Logic 73VAR 73VAR 73VAR 73VAR Drive Current (ma) LED Wattage 35W 43W 55W 73W STK-G3-MR VAR-NW-120/277-NP 16,17,18 STK-G3-MR VAR-CW-120/277-NP 16,17, Variable driver ('73VAR') ships as 700 ma. Drive current can be changed to 350, 450, or 550 ma in the field. 16. Accepts 120V or 277V input only. LED Wattage and Lumen Values - Standard G3 Luminaires Initial Lumens 20 Order Code (standard units) Array Quantity Total LEDs LED Current (ma) Average System Watts 19 LED Selection 3 Type 3 Asymmetrical 1R Rectangular 5 Type 5 CD Concentrated Downlight 1-38LA NW 3,392 (s) 3,308 3,267 3,274 (s) 2-73LA NW 6,605 (s) 6,278 6,341 6,377 (s) 2-73VAR NW 3,501 (s) 3,327 (s) 3,361 (s) 3,380 (s) 2-73VAR NW 4,029 (s) 3,830 (s) 3,868 (s) 3,890 (s) 2-73VAR NW 5,218 (s) 4,960 (s) 5,009 (s) 5,038 (s) 2-73VAR NW 6,605 (s) 6,278 6,341 6,377 (s) 3-104LA NW 9,818 (s) 9,500 9,322 9,479 (s) 4-137LA NW 13,120 (s) 12,676 12,476 12,667 (s) 1-55LA5-161A NW 4,641 (s) 4,443 (s) 4,423 (s) 4,481 (s) 2-106LA-321A NW 8,925 8,544 8,505 8, System input wattage may vary based on input voltage, by up to +/- 10%, and based on manufacturer forward voltage, by up to +/- 8%. 20. Lumen values based on photometric tests performed in compliance with IESNA LM-79. (s). Data is scaled based on tests of similar, but not identical, luminaires. LED Wattage and Lumen Values - G3 Luminaires with EM Emergency Battery Pack 21 Initial Lumens 20 - Emergency Mode Order Code (EM Units) Array Quantity Total LEDs LED Current (ma) Average System Watts 17 LED Selection 3 Type 3 Asymmetrical 1R Rectangular 5 Type 5 CD Concentrated Downlight 1-38LA NW 1,866 (s) 1,819 (s) 1,797 (s) 1,801 (s) 21. Emergency Battery pack configuration not available for use in Canada. G /13 page 2 of 5

13 G3 LED PARKING GARAGE & CANOPY Dimensions - G3 Standard Luminaires (EZ Hanger Plate Mount shown) 2 LED Array Top View 1 LED Array Top View 3 LED Array Top View (33.8 cm) (33.8 cm) (33.8 cm) (39.6 cm) (27.12 cm) 1 LED Array Side View 20.6 (52.3 cm) 2 LED Array Side View 3.2 (8.1 cm) 3.20 (8.13 cm) (27.12 cm) 3 LED Array Side View (39.6 cm) 1.18 (2.99 cm) Approximate luminaire Weight: 9.75 Lbs (4.42 Kg) 1.18 (2.99 cm) 20.6 (52.3 cm) Approximate luminaire Weight: 12.5 Lbs (5.67 Kg) 4 LED Array Top View 3.20 (8.13 cm) Approximate luminaire Weight: Lbs (6.9 Kg) 4 LED Array Side View 3.20 (8.13 cm) (33.8 cm) (65.04 cm) (65.04 cm) Dimensions - G3-EM Emergency Battery Pack* 1 LED Array Top View 1.18 (2.99 cm) Approximate luminaire Weight: 18 Lbs (8.16 Kg) Dimensions - G3-RC LimeLight Wireless 1 & 2 LED Array Front View 2 LED Array Top View (39.6 cm) 6.94 (17.6 cm) (33.8 cm) 17.9 (45.46 cm) standard mounting mounts to standard 4 square or octagonal j-boxes 1 LED Array Top View (27.13 cm) (27.12 cm) (39.95 cm) (33.8 cm) 1 LED Array Side View Approximate luminaire Weight: Lbs (5.92 Kg) (6.8 cm) (8.13 cm) (33.8 cm) (2.99 cm) Approximate luminaire Weight: 18 Lbs (8.19 Kg) *Emergency Battery pack configuration not available for use in Canada. G /13 page 3 of 5 Approximate luminaire Weight: Lbs (5.1 Kg) 1.18 (2.99 cm)

14 G3 LED PARKING GARAGE & CANOPY Specifications General Description The Philips Gardco G3 parking garage luminaire combines excellent performance with value, providing one of the most energy efficient lighting solutions for the energy and budget conscious. A complete selection of optical systems are available, including a concentrated downlight for use at entrances or at higher mounting heights. G3 luminaires are available with dimming, as well as motion response technology to expand potential energy savings. The G3 is also available with the LimeLight Wireless Lighting Control System. Housing Modular die-cast driver housing with one to four die-cast LED array heatsink assemblies. IP Rating IP66 rated driver housing with dedicated IP66 optical assemblies. Motion response luminaire are rated IP65. Energy saving benefits System efficacy up to 109 lms/w with significant energy savings over PSMH systems less controls. Optional MR motion response sensor provides added energy savings during unoccupied periods and works as a Smart Luminaire requiring no added wiring or commissioning at install. Electrical Driver efficiency (>90% standard) V available (restrictions apply). Temp range: -40 C (-40 F) to 40 C (104 F). Open/short circuit protection. Optional 0-10V dimming to 10% power. RoHS compliant. Surge protector standard and is in accordance with IEEE / ANSI C guidelines, with a surge current rating of 10,000 amps. 2-73VAR-3270 features a variable driver that allows for drive current to be switched between 350 ma, 410 ma, 530 ma, or 700 ma. Variable driver ships as a 700 ma. LED Board and Array Luxeon R LED only: lms/w, System only: lms/w. Color temps: 3000K, 4000K, 5700K +/- 250K. Minimum CRI of 70. Aluminum metal clad board. RoHS compliant. LED Performance: LED Thermal Management The housing design provides thermal radiation fins in the upper housing to provide the excellent thermal management critical to long LED system life. Optical Systems Type 5 symmetrical, Type 3 asymmetrical, Type 1R rectangular and CD concentrated downlight. Type 1R is designed to meet IES minimums with one luminaire per parking bay compared to the typical two per bay. Diffuse lens is available with Type 5 to limit perceived luminaire brightness, resulting in reduced performance. Mounting A die formed 14 ga. galvanized steel plate is supplied for mounting to a recessed, surface, or rigid pendant hung 4 (10.16 cm) j-box (standard j-box and rigid pendant by others). An integral hanger tab on the plate supports the luminaire during wiring. All pendants, including rigid pendants and swivel pendants (utilized with the balanced j-box PB-NP option), are supplied by others. Caution: Philips Gardco is not responsible for failure of mounting components supplied by others. Proper care should be exercised in mounting component selection to insure adequate luminaire support, given luminaire weight, vibration potential and thermal conditions present in the application. If luminaires are supported solely by screws into a composite j-box, additional support directly to structure is recommended. Failure to properly support the luminaire may cause damage or injury, for which Philips Gardco is not responsible. G3-RC Luminaires Luminaires are provided only as part of a complete parking garage control system. The system includes the luminaire with wireless remote control module and motion sensor, and all components and services that comprise the LimeLight Wireless Lighting Control System. The entire system must be configured and factory quoted by Philips Gardco prior to ordering. G3-RC luminaires rated to 40 C. Motion Sensors G3-MR, G3-MRCP luminaires may be specified for additional energy savings during unoccupied periods. See page 5 for detailed information. G3-EM Luminaires When power is lost, G3-EM luminaires provide emergency light output, for a minimum of 90 minutes. Luminaires include the Tenergy emergency battery pack, model A combined Indicator Light / Test Switch is provided as part of the door frame and lens on every G3-EM luminaire. G3-EM is suitable for use in ambient temperature conditions from 40 C (104 F) maximum to -10 C (14 F) minimum. G3-EM configuration is not available for use in Canada. Listings UL/cUL and ETL/cETL listed to the UL 1598 standard, suitable for Wet Locations. Suitable for use in ambients from -40 to 40 C (-40 to 104 F). G3-EM is ETL listed to the UL 924 standard. The quality systems of this facility have been registered by UL to the ISO 9001 series standards. G3 luminaires with Type-3, 5, and 1R optics, equipped with Cool White and Neutral White LEDs only, are DesignLights Consortium qualified. Finish Each luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard finish of all diecast assemblies shall be Natural Aluminum paint. Warranty G3 Luminaires feature a 5 year limited warranty. LED luminaires with LED arrays feature a 5 year limited warranty covering the LED arrays. LED drivers are covered by a 5 year limited warranty. PIR sensors carry a 5 year limited warranty from the sensor manufacturer. PREDICTED LUMEN DEPRECIATION DATA 23 Ambient Temperature C Driver ma Calculated L 70 Lumen Maintenance % L Hours 23,24 70 Per TM-21 60,000 hours Up to 40 C Up to 1050 ma > 350,000 Hours > 54,000 Hours 97.1% 23. Predicted performance derived from LED manufacturer s data and engineering design estimates, based on IESNA LM-80 methodology. Actual experience may vary due to field application conditions. 24. L 70 is the predicted time when LED performance depreciates to 70% of initial lumen output. 25. Calculated per IESNA TM Published L 70 hours limited to 6 times actual LED test hours. G /13 page 4 of 5

15 G3 LED PARKING GARAGE & CANOPY Motion Response Luminaires Motion Sensors G3-MR luminaires include a passive infrared (PIR) motion sensor (WattStopper FSP-211 equipped with an FS-L2W lens) capable of detecting motion within 22 feet of the sensor, 360 around the luminaire, when placed at an 8 foot mounting height. The PIR sensor is mounted as indicated in drawings on page 3. Available in 120V or 277V input only. Motion sensor off state power is 0.0 watts. The FSIR-100 operates on three standard 1.5V AAA Alkaline batteries or three rechargeable AAA NiMH batteries. The battery status displays in the upper right corner of the display. Three bars next to BAT= indicates a full battery charge. A warning appears on the display when the battery level falls below a minimum acceptable level. To conserve battery power, the FSIR-100 automatically shuts off 10 minutes after the last key press. In Motion Response (MR) luminaires, when no motion is detected for 10 minutes, the Motion Response system reduces the wattage by 90%, to 10% of the normal constant wattage, reducing the light level accordingly. When motion is detected by the PIR, the luminaire returns to full wattage and full light output. Dimming on low is factory set to 90% with duration set at 10 minutes. Range Lens " 59.2mm / 5.92 cm You navigate from one field to another using (up) or (down) arrow keys. The active field is indicated by flashing (alternates between yellow text on black background and black text on yellow background.) mm.78" / 1.97 cm ft 44' Coverage Side View Once active, use the Select button to move to a menu or function within the active field. Value fields are used to adjust parameter settings. They are shown in less-than/greaterthan symbols: <value>. Once active, change them using (left) and (right) arrow keys. In general the up key increments and the down key decrements a value. Selections wraparound if you continue to press the key beyond maximum or minimum values. Moving away from the value field overwrites the original value. The Home button takes you to the main menu. The Back button can be thought of as an undo function. It takes you back one screen. Changes that were in process prior to pressing the key are lost. FSP-L3: 360 Coverage Power On/Off FSP-201 FSP-211 FD-101 FD-301 BAT= FS1R-100 Wireless Remote Programming Tool The FS1R-100 Remote Programming Tool accessory permits adjustment of sensor settings, including duration and dimming level on low, without the need to connect any wires to the luminaire. The FSIR-100 Wireless IR Programming Tool is a handheld tool for setup and testing of WattStopper FSP-211. It provides wireless access to the FSP-211 sensors for setup and parameter changes. The FSIR-100 display shows menus and prompts to lead you through each process. The navigation pad provides a familiar way to navigate through the customization fields. Back Left Down Home/Main Menu Up Right/Next Select Within a certain mounting height of the sensor, the FSIR-100 allows modification of the system without requiring ladders or tools simply with a touch of a few buttons. The FSIR-100 IR transceiver allows bi-directional communication between the FSP-211 and the FSIR-100 programming tool. Simple menu screens let you see the current status of the system and make changes. It can change FSP-211 sensor parameters such as high/low mode, sensitivity, time delay, cut off and more. With the FSIR-100 you can also establish and store FSP-211 parameter profiles. More information on the FS1R-100 Remote Programming Tool is available at wattstopper.com. G /13 page 5 of 5 Philips Lighting Company 200 Franklin Square Drive Somerset, NJ Phone: Philips Lighting Company 281 Hillmount Road Markham ON, Canada L6C 2S3 Phone:

16 CATALOG NO. TYPE NO. JOB NAME LytePro32 Architectural LED Wall Sconce ORDERING INFORMATION Catalog Number: Example: LP32T LP SERIES LP- LytePro32 Architectural LED Wall Sconce ACCESORIES 32 SIZE 32- Hi-Lumen LEDs COLOR T- Titanium W- White P- Bronze PCB 1- Button-type photocontrol. 2-1/8 x 1 x 3/4. 3/8 NPS threaded nipple for use in boxes, fittings and other protective enclosures. TECHNICAL INFORMATION 1.4" R = 0.43" 12" 9.2" 9" 4.5" 4.6" 2.5" PHOTOMETRIC DATA Horizontal Footcandles Delivered Lumens = 5,840 Mounting Height = Ft Maximum Calculated Value = 2.28 Fc PRODUCT SPECIFICATIONS Provides safety and security in residential and commercial applications in locations such as entrances, over garages, wall signs and locattions along perimeters and pathways. Requires only 71 system watts for environmently-friendly operation. Thirty-two high-output LED s offer lumen maintenance: L 70 54,000 hrs at 40 C ambient. Patented Philips LED Optical System individually controls the placement of light in the target area. Type III distribution with shielded optics collects and redirects light to optimize performance. 4000K neutral color temperature delivers maximum light with high efficiency. Functions in environments with temperatures that range from -30 o C to 40 o C Housing constructed of heavy die cast aluminum, integral heat sink Corrosion resistant Duraplex II polyester powder coated finish available in white, bronze and titanium Glass lens is fully sealed to keep out water insects and dust. Electronic Class 1 LED driver accepts v, 50/60Hz input (constant current) Integral cast aluminum heat sink ensures cool operation. Complete with integral splice chamber. Built-in bubble level for accuracy. Universal mounting plate with hook and lock mounting. Optional field installed PCB1 photocontrol for automatic all night lighting. 5,840 delivered lumens IES Type III CRI 73 Efficacy: 82 LPW ETL tested suitable for wet location 5 year limited warranty* Design Lights Consortium qualified 2013 Koninklijke Philips Electronics N.V. All rights reserved. 05/13

17 codes and standards ETL Listed to UL924 Standard ETL Listed to UL1598 for wet locations NFPA 70 (National Electric Code) NFPA 101 (Life Safety Code) ARRA Buy American Compliant (when BAC suffix is specified) ADA Compliant LM-79 Compliant LM-80 Compliant construction Marine grade die cast aluminum housing with miro reflector to provide excellent photometrics. UV Stable polycarbonate lens and neoprene gasket to protect from moisture and rain. Polyester powder coat for superior protection. Choice of white or dark bronze. Consult factory for custom finishes. installation Universal J-box pattern on back or rigid conduit entry on top of housing for mounting flexibility electronics The charger system includes low voltage disconnect to prevent deep discharge of battery. AC lockout to prevent battery drain prior to the energizing of utility power, and brownout protection which will automatically switch unit into emergency mode if the utility power sags below 80% of nominal. Solidstate, fully automatic charging circuit is protected with a moisture resistant coating. All units are provided with Self-Test/Self Diagnostics. 120/277VAC dual voltage input, selectable input. Patron LED available in AC only, Emergency only, and AC with integral ni-cad battery operation may be switched on or off to operate as a mini wall light providing 740 lumens in AC mode. AC with integral ni-cad battery and emergency only will provide 500 lumens in emergency mode. self-diagnostic/self-test This feature provides automatic testing and continuous monitoring of the unit and indicates any faults via a dual-color LED lamp. The low-profile test button with easily visible status indicator is located beneath the lens. This innovative circuitry monitors battery disconnection, charger failure, lamp failure and transformer fault every 5 seconds without discharging the battery or illuminating the lamps. It will automatically indicate lamp, battery, and charger status by dual-color LED lamp. The LED lamp indicator shows the following status: Green - ON: Unit is ready. Blinking: Unit is self-testing. Red - Service Alert (see fault indications) Fault Indications: (Red LED lamp indicator) One blink ON/pause 4 seconds: Battery not connected. Two blinks ON/pause 4 seconds: Battery is shorted or battery voltage drops below the accepted value. Three blinks ON/pause 4 seconds: Charger board circuit fault. Four blinks ON/pause 4 seconds: Transformer fault. Five blinks ON/pause 4 seconds: Lamp fault. The unit will automatically initiate a self-test as follows: One minute self-test each month. 30 minute self-test on the 6th month following installation. 90 minute self-test on the 12th month following installation. Manual testing of the unit can be accomplished by pressing the test button as follows: Once - 1 minute test Twice - 5 minute test Three - 30 minute test Four - 90 minute test lamps 8-3W LED lamps provide 700 lumens in the AC mode and provide 500 initial lumens in the emergency mode. Color temperature is 4500K and provides over 50,000 hours of life in normal usage. battery AC with integral ni-cad battery and emergency units contain a 6V maintenance free sealed nickel cadmium battery with an expected service life of 8-12 years and an operating temperature of -4 F (20 C) to 122 F (50 C). Units with a battery provide a minimum of 90 minutes emergency illumination. Units with a heater will operate in temperatures as low as -20 F (-29 C). warranty Five full year warranty on units Project Type Model No. Comments Architectural Emergency Patron LED Series Die-Cast Aluminum LED Wall Light/Unit Specifier s Reference CM rev. 1, Green Product Choice: PLEMBZ-BAC Catalog Number Operation Volts LED Housing Finish Lamp Type PLACBZ AC only 6 8-3W Dark Bronze 700 Lumen Output PLACW AC only 6 8-3W White 700 Lumen Output PLEMBZ EM only 6 8-3W Dark Bronze 500 Lumen Output PLEMW EM only 6 8-3W White 500 Lumen Output PLACEMBZ* AC/EM 6 8-3W Dark Bronze 700/500 Lumen Output PLACEMW* AC/EM 6 8-3W White 700/500 Lumen Output PLACBZ-BAC AC only 6 8-3W Dark Bronze 700 Lumen Output PLACW-BAC AC only 6 8-3W White 700 Lumen Output PLACB-BAC AC only 6 8-3W Black 700 Lumen Output PLACTT-BAC AC only 6 8-3W Titanium 700 Lumen Output PLACCC-BAC** AC only 6 8-3W Custom Color 700 Lumen Output Accessories (order separately) PLHTR WG4 Option BAC Patron Heater Kit Wire Guard Buy American Compliant *AC mode for general lighting with an integral nicad battery for emergency illumination. **Must provide RAL# for custom color. PLEMBZ-BAC EM only 6 8-3W Dark Bronze 500 Lumen Output PLEMW-BAC EM only 6 8-3W White 500 Lumen Output PLEMB-BAC EM only 6 8-3W Black 500 Lumen Output PLEMTT-BAC EM only 6 8-3W Titanium 500 Lumen Output PLEMCC-BAC** EM only 6 8-3W Custom Color 500 Lumen Output PLACEMBZ-BAC* AC/EM 6 8-3W Dark Bronze 700/500 Lumen Output PLACEMW-BAC* AC/EM 6 8-3W White 700/500 Lumen Output PLACEMB-BAC* AC/EM 6 8-3W Black 700/500 Lumen Output PLACEMTT-BAC* AC/EM 6 8-3W Titanium 700/500 Lumen Output PLACEMCC-BAC** AC/EM 6 8-3W Custom Color 700/500 Lumen Output 2013 Koninklijke Philips Electronics N.V. All rights reserved. CM /13