ABP GROUP LIMITED SPECIFICATION FOR APPROVAL. Eckstein GmbH SAW GD. Manufacture Please check and confirm the specification

Size: px

Start display at page:

Download "ABP GROUP LIMITED SPECIFICATION FOR APPROVAL. Eckstein GmbH SAW GD. Manufacture Please check and confirm the specification"

Barbra Rodgers
5 years ago
Views:

1 ABP GROUP LIMITED SPECIFICATION FOR APPROVAL Eckstein GmbH CUSTOMER PART NO PART NO: SAW GD DESCRIPTION 15W EU Power Adapter DATE Manufacture Please check and confirm the specification Design Checked Approved and return it back to us for record. Jiahuan Wei Wen Sang Heny Huang Shenzhen ABP Technology Co.,LTD ADD: 3rd floor,no.14 Fengping Road,Wanfeng Third Industrial Zone,Shajing Town, Baoan District,Shenzhen City,Guangdong Province,P.R.China Page 0

2 Rev. E. C. LIST Description of Change Before After MODEL:SAW GD Changed Date A Original Release ECN No. Page 1

3 ** Table Of Content ** 1. SCOPE Description Input Characteristics Input Voltage & Frequency Input AC Current Inrush Current (cold start) Average Efficiency Energy Consumption Output Characteristics Static Output Characteristics <Vo & R+N> Line/ Load Regulation Turn - on Delay Time Hold-up Time Rise Time Fall Time Output Overshoot / Undershoot Output Load Transient Response Protection Requirements Over Current Protection Short Circuit Protection Environment Requirements Operating Temperature and Relative Humidity Storage Temperature and Relative Humidity Vibration Drop in Reliability Requirements Burn-in EMI/EMS Standards/EMI/EMS EMI Standards/EMI EMS Standards/EMS Safety Standards Dielectric Strength(Hi-pot) Leakage Current Insulation Resistance Regulatory Standards Match. Outline Drawing DC Cord Drawing/DC...9 Page 2

4 11. I/O Marking Drawing Package Drawing Sample Test Report... 错误! 未定义书签 Page 3

5 1. SCOPE The document detail the electrical, mechanical and environmental specifications of a SMPS, the power supply provide12.75w continuous output power. The power supply shall meet the RoHS requirement Description SMPS Adaptor(Wall mount) Open Frame Others 2. Input Characteristics SMPS Adaptor(Desk-top) SMPS Unit (With Case) 2.1. Input Voltage & Frequency The range of input voltage is from 90Vac to 264Vac single phase.. Minimum Nominal Maximum Input Voltage 90Vac 120Vac~240Vac 264Vac Input Frequency 47Hz 60Hz/50Hz 63Hz 2.2. Input AC Current Vac input & Full load 2.3. Inrush Current (cold start) 264Vac input 2.4. Average Efficiency 80.34%min.@ Nominal input 2.5. Energy Consumption Input: V, No load Power 0.1W 3. Output Characteristics 3.1. Static Output Characteristics <Vo & R+N> Output Rated Load Output Range R+N Remark Rate Min. Load Max. Load +5.1V 0.0A 2.5A 4.845V-5.355V 200mVp-p Ripple & Noise: Measurement is done by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 47uF electrolysis capacitor. (test under the condition of rated input and rated output) Page 4

6 3.2. Line/ Load Regulation Output Load Condition Line Regulation Load Regulation Remark Rate Min. Load Max. Load +5.1V 0.0A 2.5A 1% 5% 3.3. Turn - on Delay Time 3S 100Vac to 240Vac input & Full load 3.4. Hold-up Time 10mS Full load &115Vac/60Hz input turn off at worst case 20mS Full load &230Vac/50Hz input turn off at worst case 3.5. Rise Time 20mS Rated load 3.6. Fall Time 20mS Full load 3.7. Output Overshoot / Undershoot 10% max. When the power on or off 3.8. Output Load Transient Response Output voltage within4.845v-5.355v for load step from 25% to 50% to 25%,50% to 75% to 50% R/S: 0.25A/uS, Transient Response Recovery Time :200uS,Dynamic response overshoot 5% 4. Protection Requirements 4.1. Over Current Protection Over Current Point Limited:I<5A( Vac) The output shall hiccup when the over currents applied to the output rail, and shall be self-recovery when the fault condition is removed 4.2. Short Circuit Protection The input power shall decrease when the output rail short, the power supply shall no damage, and shall be self-recovery when the fault condition is removed 5. Environment Requirements 5.1. Operating Temperature and Relative Humidity 0 to %RH to 90%RH 5.2. Storage Temperature and Relative Humidity -20 to +80 5%RH to 95%RH Sea level shall be low 2,000 meter. Page 5

7 5.3. Vibration 10 to 300Hz sweep at a constant acceleration of 1.0G(Breadth: 3.5mm) for 1Hour for each of the perpendicular axes X, Y, Z 5.4. Drop in Height: 1m; the product should be fell off on the hardwood with the thickness of 20mm, and the hardwood should be put on the base of the cement or on the ground without flexibility. Apply one times on all surface. Apply one times on all corner. 6. Reliability Requirements 6.1. Burn-in The power supply shall be burn-in for 4 Hours under normal input and 80% rated load at EMI/EMS Standards 7.1. EMI Standards EN55022 EN EMS Standards electrostatic discharge(esd) requirement Discharge characteristic Test level Test criteria Air discharge +/-8KV B Contact discharge +/-4KV B 7-2-2,radiated electromagnetic field susceptibility(rs) Test level 3V/m (r.m.s) MHz,80%AM(1KHz) sine-wave Test criteria A electric fast transients(burst) immunity requirement Coupling Test level Test criteria AC-input 0.5KV A AC-input 1KV B Page 6

8 7-2-4,surge capability requirement Surge voltage Test criteria Common mode N/A A Differential mode 1KV 7-2-5, Induced radio frequency fields conducted disturbances immunity requirement Test level 3V MHz,80%AM(1KHz) Test criteria A Assessment criteria Acceptance criteria Performance A B C Agreed operational behavior within the specified limits Time limited functional diminishment or malfunction during the tests is permitted. The function is self-reactivated by the unit following completion of the tests. Malfunction is permitted.the function can be reactivated either by reconnection to the mains or by operator intervention. 8. Safety Standards 8.1. Dielectric Strength(Hi-pot) Primary to Secondary: 3000Vac / 10mAMax / 60 second Primary to Secondary: 3300Vac / 5mAMax /3S 8.2. Leakage Current 0.25mAmax. at 264Vac / 50Hz 8.3. Insulation Resistance 50MΩ min. at primary to secondary add 500Vdc test voltage 8.4. Regulatory Standards Type Country Standard State Note CE Europe EN Approved Page 7

9 9.Match. Outline Drawing Black Housing Housing Material: PC:120 PC+ABS:95 Remark:PC Material can meet the requirement of ball pressure test requirement Page 8

10 MODEL:SAW GD 10.DC Cord Drawing 10.4± ± ± 0.1 Pin1 + - Pin5 8.7± ± 30 80±10 6.5± 0.1 Φ12.2± ± 0.3mm MΩ Page 9

11 11.I/O Marking Drawing Remark:Laser print the label Remark:Import:xxx represent importer Address:xxx represent the address YYMM represent the year and month, will change according to the order time. Page 10

12 12.Package Drawing (470*365*190mm) Page 11

PRODUCT SPECIFICATION File: EA-A0601HE-12 Model: SSA-0601HE-12 Date: Apr. 17, 2015

PRODUCT SPECIFICATION File: EA-A0601HE-12 Model: SSA-0601HE-12 Date: Apr. 17, 2015 SWITCHING POWER SUPPLY Rev.: A0(+12V/5A) Page: 1 of 5 1.0 Introductions: 2 2.0 AC Input Characteristics: 2 2.1 Input Voltage Rating:. 2 2.2 Input Voltage Range: 2 2.3 Input Frequency: 2 2.4 AC Inrush current: