Building Automation KNX. Conservatory Automation
|
|
- Cynthia Fleming
- 5 years ago
- Views:
Transcription
1 Building Automation KNX Conservatory Automation New Products April 2010
2 Sensors The Weather Station Suntracer KNX-GPS provides the current meteorological data (brightness, wind speed, pecipitation and temperature) for KNX networks. The GPS signal (international time signal, position) is received additionally. The devices can therefore calculate the position of the sun and handle time functions (calendar/ week time switch). All measured and calculated data may be used for the control of switching outputs which depend on limit values. The states may be linked by means of AND and OR logic gates. Functions like tracking of the slats and shadow edge can be realised with the integrated shading control for 6 fronts. GPS Weather Station Housing: Surface mounting, protection category IP 44, white/ translucent, dimensions: approx. 96 x 77 x 118 (W x H x D, mm) Operating voltage: VDC (12-28 VAC); appropriate 20 VAC power supply unit optionally available Temperature measurement: ambience C Brightness measurement: 1 sensor, measurement range lux; calculation of the position of the sun Shading control for up to 6 fronts with tracking of the slats and shadow edge GPS receiver, calendar time switch (3 annual terms with 2 daily periods), week time switch (4 daily periods) 8 AND and 8 OR logic gates: 4 inputs each, each output to be configured as 1 bit or 2x8 bits Integrated combined mounting bracket for wall and pole mounting; hinge arm mounting* available as an option KNX TH65-AP measures temperature and air humidity in indoor or outdoor areas and calculates the dew point. External measured values may be received by the bus and mixed with the own measured values to make up a total temperature and total humidity. It is possible to set seven switching outputs (adjustable threshold values) as well as logic gates by means of the KNX software ETS. KNX TH65-AP has a PI controller for a heating and a cooling system (temperature) and ventilation (humidity). Temperature/Humidity Sensor KNX TH65-AP Housing: Surface mounting, protection category IP 65, grey, dimensions: approx. 65 x 93 x 38 (W x H x D, mm) Operating voltage: KNX voltage (via +/- bus plug terminal) Temperature measurement: ambience C Measurement of air humidity: % R.H. PI controller for heating and cooling (temperature) and ventilation (humidity) KNX AQS/TH measures CO 2 concentration, temperature and air humidity in a room and calculates the dew point. Eleven switching outputs with adjustable threshold values as well as logic gates can be set by means of the KNX software ETS. The sensor may imply value of other devices and thus calculate room averages. KNX AQS/TH has a PI controller for ventilation (according to CO 2 concentration and air humidity) and for heating and cooling (according to temperature) and can pass a warning to the bus as soon as the comfort field (according to DIN 1946) is left. Indoor Sensor KNX AQS/TH Housing: Wall mounting in junction box ( 70 mm, 36 mm deep), plastic material, white matt, dimensions: cover approx. 94 x 94 (W x H, mm), mounting depth approx. 8 mm Operating voltage: VDC / VAC CO 2 measurement: ppm Temperature measurement: ambience C Air humidity measurement: % R.H. PI controller for ventilation (according to CO 2 and humidity) and for heating and cooling (according to temperature) 2 * Devices not supplied Available from 2nd quarter of 2010
3 System Devices The KNX WS1000 Color is an operating and control unit for drives and devices in the KNX system. Additional radio channels allow for direct wireless connection of drives and devices to the control. The integrated automatic functions offer manifold settings for shading, ventilation, heating/cooling, light and also for gutter heatings. The Data of motion and smoke detectors may be included, too. The key element of the KNX WS1000 Color is the colour display with touch functionality. It provides operation of the connected devices and adjustment of settings. The user interface was designed according to evolutionary-biological findings and easily guides through the set-up steps. If no operation is made the display shows the current weather information, the course of the sun or rain and snow fall. Control System KNX WS1000 Color Housing: Plastic material white/grey or aluminium/graphite (partly lacquered). Dimensions: approx. 250 x 182 x 43 (W x H x D, mm), concealed box approx. 235 x 169 x 62 (W x H x D, mm) Colour touch display 8.4 inches Operating voltage: 230 V, 50 Hz Wattage (stand-by): approx. 16 W KNX connection for data transfer (+/- bus plug terminal) 32 free radio channels e. g. for Elsner Elektronik ventilation units, radio switches and motor control units (RF Relay, RF MSG), WGTH-UP Indoor Sensors* Remote Control Remo 8 as accessory* (p. 8) Supply of weather data via KNX or by optional weather station P03i-GPS (brightness, wind, precipitation, temperatur, GPS signal) Apart from free adjustable display elements, the KNX touch panel for room automation offers internal automatic functions for shading (sun protection/screen) and the control of room climate (heating, cooling, ventilation). The colour display with touch functionality shows data and allows for the switching of light and shading and setting of the automatic. Additionally, four binary inputs and the radio remote control Remo 8 (available separately) may be used for manual operation. KNX Touch One is available white or aluminium coloured and has got an integrated temperature and humidity sensor. The internal automatic is completed by bus functions for timing and scene control. Touch Panel for Room Automation! Housing: Plastic material white/grey or aluminium/graphite (partly lacquered). Dimensions: approx. 164 x 121 x 29 (W x H x D, mm) Colour touch display 5.7 inches Integrated indoor sensor (temperature, air humidity) Operating voltage: V AC ( V DC), Wattage (display on): approx. 9 W KNX connection for data transfer (+/- bus plug terminal) Remote Control Remo 8 as accessory* (p. 8) The interface is plugged on the board of the Control System WS1000 Color and allows for communiction with the KNX bus system. Weather data and movement/switching commands can be transferred in both directions. So on the one hand the data of WS1000 Color may be used in the KNX system, on the other hand drives and devices in the KNX system may be controlled by the automatic of the WS1000 Color. KNX Interface for WS1000 Color Dimensions board: approx. 53 x 7 x 30 (W x H x D, mm) Connection: Interface and KNX bus plug terminal are plugged on the board of WS1000 Color Available from 2nd quarter of 2010! Available from 3rd quarter of 2010 * Devices not supplied 3
4 Sensors RS485 The sensor system of the weather stations is protected by the compact housing which is provided with a fixture for the assembly to the wall or pole. Brightness, wind speed, temperature and precipitation are collected. The P03/1-RS485 has one sun sensor and a DCF77 receiver (date, time). The P03/3-RS485 has three sun sensors (east, south, west) and a DCF77 receiver (date, time). P03/3-RS485 is also available for the WAGO I/O System (with adapted sending time for data). The P03/3-RS485-GPS has three sun sensors (east, south, west) and a GPS receiver (UTC, position). The device additionally exports the position of the sun (azimuth, elevation). Weather Stations P03/1-RS485 and P03/3-RS485(-GPS) Housing: Surface mounting, protection category IP 44, white/ translucent, dimensions: approx. 96 x 77 x 118 (W x H x D, mm) Operating voltage: 24 VDC Temperature measurement: ambience C Brightness: P03/1-RS485: 1 sensor, P03/3-RS485: 3 sensors. Measurement range lux, recognition of twilight DCF77 time receiver respectively GPS receiver Sensors Modbus The sensor system of the P03-Modbus Weather Stations is protected by the compact housing which is provided with a fixture for the assembly to the wall or pole. Brightness, wind speed, temperature and precipitation are collected. The P03/3-Modbus-GPS in addition receives the GPS signal and exports time (UTC), position (degree of longitude and latitude) and position of the sun (azimuth, elevation). Weather Stations P03/3-Modbus and P03/3-Modbus-GPS Housing: Surface mounting, protection category IP 44, white/ translucent, dimensions: approx. 96 x 77 x 118 (W x H x D, mm) Operating voltage: 24 VDC Temperature measurement: ambience C Brightness measurement: 3 sensors, measurement range lux, recognition of twilight P03/3-Modbus-GPS: with GPS receiver Accessories The GPS-DCF Converter may be connected to a DCF77 signal input as an alternative to a DCF77 antenna. The device receives the international time UTC via GPS and transcribes this information to the DCF77 protocol. The system/device the GPS-DCF Converter is connected to, must be equipped with the function conversion of UTC time to local time. GPS-DCF Converter Housing: Surface mounting, protection category IP 54, grey, dimensions: approx. 80 x 80 x 55 (W x H x D, mm) Auxiliary voltage: 24 VDC DCF output +24 V / - / out 4
5 Motor Control Units The intelligent motor control units control two respectively four drives (IMSG-UC-2H, IMSG-UC- 4H). The voltage of the central and subsidiary inputs is variable. Central control may be set to dead man s control or self-retaining mode selectively. Keys for manual operation of the motors and status LEDs are integrated in the devices. For local manual operation, not interlocked up-down push-buttons are connected. The reaction of the buttons (standard or comfort mode) may be set. Furthermore, it is possible to store a movement position for each drive. Motor Control Units IMSG-UC Housing: Modular device for mounting rails IMSG-UC-2H: 3 width units, approx. 53 x 88 x 60 (W x H x D, mm), white IMSG-UC-4H: 6 width units, approx. 107 x 88 x 60 (W x H x D, mm), white Auxiliary voltage: 230 V AC Voltage central/subsidiary inputs: 6 80 V DC, V AC Connect through clamps Potential-free relays IMSG-UC-2H: 2 connections for 230 V drives 2 connections for up/down push-buttons IMSG-UC-4H: 4 connections for 230 V drives 4 connections for up/down push-buttons IMSG-UC-2H IMSG-UC-4H The motor control units control two respectively four drives of blinds with double position switches (MSG-2H-DES, MSG-4H-DES). A central input (up/down), an ES input for blocking of local operation and an SP input for dead man s control of central and local operation are available as special inputs. Keys for manual operation of the motors and status LEDs are integrated in the devices. For local manual operation, not interlocked up-down push-buttons are connected. Motor Control Units MSG-DES Housing: Modular device for mounting rails MSG-2H-DES: 3 width units, approx. 53 x 88 x 60 (W x H x D, mm), white MSG-4H-DES: 6 width units, approx. 107 x 88 x 60 (W x H x D, mm), white MSG-2H-DES Auxiliary voltage: 230 V AC Central input (up/down) ES input (local block) SP input (dead man s control operation) Connect through clamps MSG-2H-DES: MSG-4H-DES 2 connections for drives with double position switches 2 connections for up/down push-buttons MSG-4H-DES: 4 connections for drives with double position switches 4 connections for up/down push-buttons The intelligent motor control unit with integrated power supply unit allows for central or group control of three 24 VDC motors (e. g. of indoor shadings). For local manual operation, not interlocked up-down push-buttons are connected. Due to the integrated automated time system for buttons, a short keypress causes automatic movement to the end position, a long keypress causes slow movement (for exact positioning or adjustment of the slat angle). Motorsteuergerät IMSG 24-NG3 Housing: Surface mounting, protection category IP 54, grey, dimensions: approx. 200 x 86 x 120 (W x H x D, mm) Operating voltage: 230 VAC, 50 Hz 1 input for central commands, connect through clamp 3 inputs for local push-buttons 3 outputs for drives: 24 VDC, max 600 ma each, with up/down clamps 5
6 Building Control WS1000 Color and WS1 Color are operating and control units for building technology in conservatories, private homes and smaller commercial buildings. The automatic control ensures optimal room conditions and provides safety and comfort functions. Due to their flexible connection and set-up options the controls even meet sophisticated requirements. The key element is the colour display with touch functionality. It provides operation of the connected devices and adjustment of settings. The user interface was designed according to evolutionary-biological findings and easily guides through the set-up steps. If no operation is made the display shows the current weather information, the course of the sun or rain and snow fall. If the ambient brightness is low the display automatically darkens in order to save energy. Drives and devices are connected to the control systems directly. Radio channels for wireless connection are available additionally. Thus motors of shading elements or windows may be controlled via wireless motor control units RF- MSG. Systems like heating or illumination may be switched via wireless relays RF Relay. Ventilation units of Elsner Elektronik communicate with the controls directly via radio, an additional module is not required. The main automatic functions of the control systems are sun protection and ventilation. Awnings, blinds and shutters are controlled according to brightness and also according to the direction and height of the sun. This helps to avoid direct solar irradiation while simultaneously enabling natural daylight illumination of the room to the largest possible extent. Furthermore, the shading elements are not lowered until the required room temperature is reached helping to utilize solar heat. Continued on page 7 Control System WS1000 Color Indoor sensor and central unit white/grey Indoor sensor and central unit aluminium/graphite Scope of delivery: WS1000 Color central unit: Housing plastic material white/grey or aluminium/graphite (partly lacquered). Dimensions: approx. 250 x 182 x 43 (W x H x D, mm), concealed box approx. 235 x 169 x 62 (W x H x D, mm) Indoor sensor WGTH-UP: Housing plastic material white or aluminium (partly lacquered, according to the colour of the central unit), wall mounting in socket with frame. Dimensions: Housing approx. 55 x 55 (W x H, mm), mounting depth approx. 15 mm Weather station: Housing white/translucent, dimensions: approx. 96 x 77 x 118 (W x H x D, mm) Central unit: Colour touch display 8.4 inches Operating voltage: 230 V, 50 Hz Weather station Wattage (stand-by): approx. 16 W 4, 6, 8 or 10 drive groups for awnings, blinds, roller shutters, windows and sliding doors* 4 multifunctional outputs for heating, cooling, supply air, alarm systems, illumination, dimmer or gutter heatings* 4 multifunctional inputs for motion or smoke detectors* 32 free radio channels e. g. for Elsner Elektronik ventilation units, radio switches and motor control units (RF Relay, RF MSG), additional WGTH-UP Indoor Sensors* Remote Control Remo 8 as accessory* (p. 8) Connectivity for 10 external manual keys* Indoor sensor: Operating voltage: external voltage VDC or 9 V battery Measurement of temperature and air humidity Radiocommunication with central unit Weather station: Operating voltage: 24 VDC Temperature measurement Brightness measurement with recognition of twilight (calculation of the position of the sun by the control) DCF77 time receiver Integrated combined mounting bracket for wall and pole mounting; hinge arm mounting* available as an option 6 * Devices not supplied
7 Building Control Continued from page 6 Irrespective of this, the controls protect the connected shading elements against damages due to wind or rain. The integrated clock allows realization of comfort functions such as closing of shutters as visual protection. The automatic ventilation depends on temperature and air humidity. For example, in the summer, the windows are opened during night time for cooling purpose until the required indoor temperature is reached. A rain alarm function prevents damages due to humidity. Also heaters, motor-driven ventilation units, and air conditioning systems are regulated by the controls ensuring that the required indoor temperature is maintained. In areas with frequent snowfall a roof gutter heating ensures unobstructed outlet of snowmelt. Safety inside the building is improved by connection of smoke and motion detectors. Smoke alarm starts ventilation (smoke extraction) and creates escape routes by retraction of shading elements. Alarm from a motion detector closes windows and can be forwarded e. g. to an alarm system or illumination. Also individual requirements, such as timerbased control of a pond pump or atmospheric illumination of garden and house are realized by the Building Control Systems WS1000 Color and WS1 Color. Control System WS1 Color Scope of delivery: WS1 Color central unit with integrated indoor sensor (temperature, humidity): Housing plastic material white/grey or aluminium/graphite (partly lacquered). Dimensions: approx. 164 x 121 x 29 (W x H x D, mm), concealed box approx. 152 x 92 x 62 (W x H x D, mm) Weather station: Housing white/translucent, dimensions: approx. 96 x 77 x 118 (W x H x D, mm) Central unit: Colour touch display 5.7 inches Operating voltage: 230 V, 50 Hz Weather station Wattage (stand-by): approx. 10 W 1, 2, 3 or 4 drive groups for awnings, blinds, roller shutters, windows and sliding doors* 2 multifunctional outputs for heating, cooling, supply air, alarm systems, illumination, dimmer or gutter heatings* 2 multifunctional inputs for motion or smoke detectors* 32 free radio channels e. g. for Elsner Elektronik ventilation units, radio switches and motor control units (RF Relay, RF MSG), additional WGTH-UP Indoor Sensors* Remote Control Remo 8 as accessory* (p. 8) Connectivity for 4 external manual keys* Weather station: Operating voltage: 24 VDC Temperature measurement Brightness measurement with recognition of twilight (calculation of the position of the sun by the control) DCF77 time receiver Integrated combined mounting bracket for wall and pole mounting; hinge arm mounting* available as an option RF MSG and RF-MSG-PF are wireless motor control units for the Control Systems WS1000 Color, WS1 Color and KNX WS1000 Color. One drive (e. g. shading or window) can be connected to the control units. RF-MSG and RF-MSG-PF may also be controlled directly with the Remo 8 Remote Control (without additional device). Wireless Motor Control Units RF-MSG for WS1000 Color, WS1 Color and KNX WS1000 Color Housing: Built-in type for assembly in junction box, dimensions: approx. 38 x 47 x 29 (W x H x D, mm, plus flexible antenna) Operating voltage: 230 VAC Radio frequency: MHz 1 output for drive RF-MSG-PF RF-MSG: 230 VAC / 4 A, with up/down clamps RF-MSG-PF: 230 VAC / 4 A, RF-MSG potential-free, with up/down clamps Available from 2nd quarter of 2010 * Devices not supplied 7
8 Building Control The wireless hand-held transmitter offers an up, down and stop control for 8 channels and can be taught in to different Elsner Elektronik devices. As long as the remote control is not in use, it can be stored safely in the supplied magnetic wallmounting. Remote Control Remo 8 For Control Systems WS1000 Color, WS1 Color, Solexa and Arexa For Control Systems KNX WS1000 Color and KNX Touch One For direct operation of ventilation units WL610, WL305 and WFL For direct operation of Wireless Relay RF-Relay and of Motor Control Units RF-MSG and XS-MSG2-AP Housing: Plastic material, white/grey or aluminium/graphite (partly lacquered), dimensions: hand-held transmitter approx. 41 x 140 x 21, mounting approx. 54 x 150 x 11 (W x H x D, mm) Power supply hand-held transmitter: 3 V battery type CR2032 Radio frequency: MHz Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D Gechingen Germany Phone: +49 (0) 70 56/ Fax: +49 (0) 70 56/ info@elsner-elektronik.de Elsner Elektronik GmbH Version Technical modifications and errors reserved.
BUILDING AUTOMATION. For KNX, RS485 and Modbus Bus Systems and for Conventional Applications
BUILDING AUTOMATION For KNX, RS485 and Modbus Bus Systems and for Conventional Applications 1 25 % Automatic solar protection: Potential energy savings 25%* and more 28 % Individual room temperature control:
More informationKNX S-B2-UP. Actuator for 230 V or 24 V. Installation and Adjustment
EN KNX S-B2-UP Actuator for 230 V or 24 V Installation and Adjustment 1 Content 1. Description... 3 1.1. Technical data... 3 1.2. Structure... 4 1.2.1. Structure 230 V AC version... 4 1.2.2. Structure
More informationBUILDING AUTOMATION. For KNX, RS485 and Modbus Bus Systems and for Conventional Applications
BUILDING AUTOMATION For KNX, RS485 and Modbus Bus Systems and for Conventional Applications 19% Automatic ventilation system: Potential energy savings 19%* and more 28% Individual room temperature control:
More informationKNX S-B4T-UP. Actuator for 230 V or 24 V. Installation and Adjustment
EN KNX S-B4T-UP Actuator for 230 V or 24 V Installation and Adjustment 1 Content 1. Description... 3 1.1. Technical data... 3 1.2. Structure... 4 1.2.1. Structure 230 V AC version... 4 1.2.2. Strucure
More informationAir Quality Sensor KNX AQS
EN Air Quality Sensor KNX AQS Technical Specifications and Installation Instructions Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0
More informationKNX T-UP. Temperature Sensor. Technical specifications and installation instructions
EN KNX T-UP Temperature Sensor Technical specifications and installation instructions Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0
More informationKNX S4-B10 230V. Multifunctional Actuator. Installation and Adjustment
EN KNX S4-B10 230V Multifunctional Actuator Installation and Adjustment 1 Content 1. Description... 3 1.1. Technical data... 4 2. Installation and start-up... 5 2.1. Notes on installation... 5 2.2. Device
More informationWeather station AP 257/51
Gamma instabus Weather station GPS AP 257/61 Weather station AP 257/51 Technical product information 5WG1 257-3AB61 5WG1 257-3AB51 Weather station with sensors to survey temperature, brightness, rain and
More informationWeather station GPS AP 257/61 Weather station AP 257/51
Gamma instabus Weather station GPS AP 257/61 Weather station AP 257/51 Technical product information 5WG1 257-3AB61 5WG1 257-3AB51 Weather station with sensors to survey temperature, brightness, rain and
More informationBuilding Control GAMMA instabus
The worldwide standard for home and building control Building Control GAMMA instabus siemens.com/gamma The comprehensive GAMMA instabus product portfolio comprises intelligent devices and is your key to
More informationVerwendung des Applikationsprogramms. 1. Function overview. GAMMA instabus Application program description. September 2010
Verwendung des Applikationsprogramms Product family: Product type: Manufacturer: Physical Sensors Weather station w/ integrated sensors Siemens Name: Weather station WS1 (GPS) AP 257/32 Order no.: 5WG1
More informationVENTILATION BUTTONS 24 V DC
VENTILATION BUTTONS 24 V DC Ventilation button (with foil push buttons and displys) Application: Ventilation button for connection to the ventilation inputs of SHEV or natural ventilation control units.
More informationGeneral catalogue Export SMOUTS ARCHITECTEN
General catalogue 2011-2012 Export SMOUTS ARCHITECTEN 01 NIKO HOME CONTROL INTERIEUR DEWAIDE Project management Configuratie Installatie Help Niko Home Control (available from 1 August 2011) Live it, love
More informationRoom controller LS 990 / LS plus Stainless Steel / Aluminium
Room controller LS 990 / LS plus Stainless Steel / Aluminium 1 RCDES 2021 RCDES 2022 RCDES 2023 RCDES 2024 RCDES 2044 2 Ref.-No. KNX room controller display ETS-product family: Heating, ventilation, A/C
More informationScreenLine Accessories MB model
ScreenLine Accessories MB model ST2121 Control Module 1 group of blinds (PC configuration) control (Potential separated) Individually configurable via Configuration Utility (PC) DIN rail mounting Dim.:
More informationChorus Home Automation KNX - Easy BUS
Chorus KNX - Easy BUS KNX Easy protocol BUS system, according to EN50090 European Standard for Home Automation. Simplified programming that does not require a PC. Portable solution, thanks to the wireless
More informationABB i-bus EIB / KNX Shutter Actuator with Manual Operation, 4-fold, SMI, MDRC JA/S 4.SMI.1M. Product Manual. Intelligent Installation Systems ABB
Product Manual ABB i-bus EIB / KNX Shutter Actuator with Manual Operation, 4-fold, SMI, MDRC JA/S 4.SMI.1M Intelligent Installation Systems ABB JA/S 4.SMI.1M Shutter Actuator with Manual Operation, 4-fold,
More informationKNX/EIB KNX Blind actuator. 1 Safety instructions. 2 Device components. Blind actuator 4-gang 24 V DC Order-No. :
Blind actuator 4-gang 24 V DC Order-No. : 2154 00 Blind actuator 4-gang 230 V AC Order-No. : 2160 00 Blind actuator 2-gang 230 V AC Order-No. : 2152 00 Blind actuator 4-gang 230 V AC Order-No. : 1039 00
More informationVARIA VARIA 826 S WH KNX VARIA 826 S BK KNX D GB F I E NL. Installation and operating instructions Room thermostat VARIA 826 S KNX
307031 VARIA VARIA 826 S WH KNX VARIA 826 S BK KNX 8269210 8269211 GB Installation and operating instructions Room thermostat D GB F I E NL VARIA 826 S KNX Contents Basic safety instructions 3 Display
More informationOpen/close controller for AC drives UMS 5 UMS U5 UMS 5P
/close controller for AC drives UMS 5 UMS U5 UMS 5P (rail mounting versions: 230V AC, 24V UC) (flush mounting version: 230V AC, 12-24V UC) (rail mounting version 230V AC, electrically isolated auxiliary
More informationProduct and functional description
Product and functional description The RS 520/23 shutter / blind actuator is a KNX device with one relay output. The device is installed in an AP 118 Control Module Box or an AP 641 Room Control Box. The
More informationPush-buttons 18. Light scenes push-buttons 21. Push-buttons with thermostat 22. Labelling ields 24
A wide array of alternative materials and colours have been added to the convenient variety of KNX functionality of the. Frameless KNX push-button with full-material rockers (glass, stainless steel and
More informationRoller shutters and awning operators Convenient controls for comfortable living
Roller shutters and awning operators Convenient controls for comfortable living 2 About SOMMER About SOMMER WE DELIVERY THE QUALITY YOU ENJOY THE CONVENIENCE! With reliable gate operators from SOMMER,
More informationKNX Radio Frequency (KNX RF) Products
KNX Radio Frequency (KNX RF) Products KNX RF S-Mode Products KNX RF Motor Control Unit ELSNER The KNX RF-MSG-ST motor control unit integrates the drive of a shading element or window into the KNX bus system
More informationGlass sensors 35. Supplementary products 39
Understatement is an art, and the makes it perfect. Up to eight functions are concealed under a pure surface that is practically flush with the wall, and can be custom-labelled on request. A single touch
More informationProduct documentation
Product documentation Rotary sensor ALBRECHT JUNG GMBH & CO. KG Volmestraße 1 58579 Schalksmühle Telefon: +49.23 55.8 06-0 Telefax: +49.23 55.8 06-2 04 kundencenter@jung.de www.jung.de Service Center Kupferstr.
More informationGira Event The new definition
Gira Event The new definition New. Gira Event Clear. Clear, deep appearance in six colours. Gira Event Opaque. Seven colours in translucent material. Gira Event. Four colour variants in high quality thermoplastic.
More informationDupline Fieldbus Components
Dupline Fieldbus Components Channel Generators/Interfaces Types D390 G300 G396 G39 Standard channel generator. 77 x x 70 Controller and Modbus Interface with built-in GSM Modem (option) or external Radio
More informationswitching controlling counting
SAVE TIME ILLUMINATE CONNECT FEEL WELL ACCESSORIES Compact catalogue 2018 2019 Compact catalogue 2018 2019 SAVE TIME Digital time switches Digital time switches week Page 6 9 Digital time switches astro
More informationLUXORliving System manual Version 1
LUXORliving System manual Version 1 2018-04-18 Contents 1 General 3 2 System 4 3 Installation 5 4 Start-up 7 4.1 Establish a connection 7 4.2 Configuration with LUXORplug 10 4.3 Programming with LUXORplug
More informationKNX Building Automation
KNX A building which can think for itself? The future is here. Our building automation offer in Tebis.KNX can turn a building into an intelligent machine. It provides true control of heating, lighting
More informationPower Supply Systems KNX PS640 and KNX PS640 USB
Power Supply Systems KNX PS640 and KNX PS640 USB Item numbers 70140, 70143 (USB) Technical Data and Installation Notes Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 75395 Ostelsheim
More informationRoller Shutter Guide. Radio Motors with Wireless Controls
Roller Shutter Guide Radio Motors with Wireless Controls Technology an integral part of everyday life Introducing the next generation roller shutter motor and control solutions from SWS UK. In todays world,
More informationRoller Shutter Guide. Radio Motors with Wireless Controls
Roller Shutter Guide Radio Motors with Wireless Controls Technology an integral part of everyday life Introducing the next generation roller shutter motor and control solutions from SWS UK. In todays world,
More informationPROFESSIONAL WIRELESS WEATHER STATION. Operation Manual - 1 -
PROFESSIONAL WIRELESS WEATHER STATION Operation Manual - 1 - OVERVIEW Outdoor sensor: 1. Wind Vane 2. Wind Speed Sensor 3. Solar panel 4. Battery compartment 5. LED Indicator: light on for 4 seconds during
More informationHow to choose the correct Mount Kelvin central unit
Installation guide Outside world Property Wirepas mesh Mount Kelvin app Internet connection Ethernet DALI 3rd party integrations Mount Kelvin cloud Mount Kelvin central unit Voice control EnOcean wireless
More informationFEATURES AND BENEFITS. Installation and operation. Controller
DFC 350 & 450 DISPLACEMENT FREE COOLING Function The Dantherm Displacement Free Cooling (DFC) unit is a slim, passive cooling solution designed to remove excess heat from rooms with sensitive equipment.
More informationUsing the application program. Functional description. GAMMA instabus Application Program Description. October Event Module 800A06
Using the application program Product range: Product type: Manufacturer: Controllers Controllers Siemens Name: Event Module N 341 Order No.: 5WG1 341-1AB01 Functional description With the help of a special
More informationApplication description
Manufacturer Berker Motion detector Application description KNX motion detector module comfort 1.10m KNX motion detector module comfort 2.20m ETS KNX motion detector module comfort 1.10m ETS KNX motion
More informationABB i-bus KNX Blind/Roller Shutter Actuator JRA/S Product Manual
ABB i-bus KNX Blind/Roller Shutter Actuator JRA/S Product Manual ABB i-bus KNX Contents Contents Page 1 General... 3 1.1 Using the product manual...4 1.1.1 Structure of the product manual...4 1.1.2 Notes...5
More informationColour Touch Panel 3.5
Guangzhou Video-star Electronics Industrial Co., Ltd K-BUS R Colour Touch Panel 3.5 User manual-ver. 1.2 CHTF-35/01.1 CHTF-35/01.2.21 CHTF-35/01.2.22 CHTF-35/01.2.24 KNX/EIB Intelligent Installation Systems
More informationConnection unit for multiple wall-mounted printed circuit board
Niko Home Control 2 2.01-1 Niko Home Control Controls Simple wall-mounted printed circuit board with bridge The wall-mounted printed circuit board enables you to connect a control to the installation.
More informationABB i-bus EIB. Shutter Actuator, 2-fold, 6 A, 230 VAC, MDRC JA/S 2.6.1, GH Q R0111
, GH Q31 0022 R0111 The 2-fold shutter actuator is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via a bus connecting terminal. It is used to control two
More informationProduct and Application Description
Technical Product - Information Product and Application Description The room temperature controller UP 237K and UP 252K are available in the following colors, matching the design of the wall switch design
More informationProduct documentation
Product documentation Universal push-button module with integrated BCU, 1-gang Universal push-button module with integrated BCU, 2-gang Universal push-button module with integrated BCU, 3-gang Universal
More informationTebis application software
5 Tebis application software SXB322AU V 1.x 2 inputs / 2-output module LED SXB344AU V 1.x 4 inputs / 4-output module LED Product reference Product designation TXB322AU TXB344AU Embedded module: 2 inputs
More informationanimeo Multi-faceted façade management through intelligent sun protection
Multi-faceted façade management through intelligent sun protection About Somfy Founded in 1960 in Cluses (France), Somfy has invented, designed and created controls and motors for openings and closures
More informationClub Blue. Bring your home to life. with smart lighting 1
Club Blue Bring your home to life with smart lighting 1 2 Philips Hue welcomes you home and lets you remotely control your lights from your bedroom to your backyard. 3 Set your lights for when you are
More informationUse of the application program. Table of Contents. GAMMA instabus Application program description. April B0 CO Room Control Unit
Use of the application program Product family: Product type: Manufacturer: Displays Display and operating units Siemens AG Name Room control unit UP 227 DELTA i-system Order no.: Table of Contents 5WG1
More informationWebinar KNX Sensors commercial Buildings
JUNE 2017 Webinar KNX Sensors commercial Buildings BU EPBP GPG Building Automation Carolina Bachenheimer-Schaefer, Thorsten Reibel, Jürgen Schilder & Ilija Zivadinovic Global Application and Solution Team
More informationLDALI ME204-U, LDALI ME201 U
Functions BACnet/ Controller L ME204-U, L ME201 U BACnet CEA 709 Modbus OPC Datasheet #89021219 L WEB, L STUDIO L Controllers are multifunctional devices combining constant light con trol, sunblind control
More informationShutter/Blind Controls
/2 Inserts /5 /11 Accessories and spare parts /1 Siemens AG 2007 Inserts Selection and ordering data 5TA2 154 (front view) General information Non-insulated parts of inserts covered by molded plastic Self-retracting
More information7-day room temperature controller
s 2 208 7-day room temperature controller Heating applications REV34.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display and large
More informationinstabus EIB System Actuator
Product name: 4-channel blind/shutter actuator with manual control, 230 V Design: Modular rail-mounting device Item no.: 1048 00 ETS search path: shutter / shutter / shutter/blind actuator 4-gang 230V
More informationLDALI ME204-U, LDALI ME201 U
Functions DAI ME204-U, DAI ME201 U BACnet CEA 709 Modbus DAI OPC Datasheet #89021219 WEB, STUDIO DAI Controllers are multifunctional devices combining constant light con trol, sunblind control and gateway
More informationCAMERA-MONITOR SYSTEMS
CAMERA-MONITOR SYSTEMS FOR RECREATIONAL AND COMMERCIAL APPLICATIONS INSPIRED BY COMFORT 150546_reversing Brox2015V2_AM.indd 1 16/06/2015 3:42 pm 2 PERFECT VIEW SOLUTIONS READY-TO-INSTALL SYSTEMS FOR EVERY
More informationINDEX PRESENCE DETECTOR AND BRIGHTNESS SENSOR INFRARED TRANSMITTER/RECEIVER & DECODER. PLC LOGO! and COMMUNICATION MODULE
INDEX INTRODUCTION SINGLE PHASE POWER UNIT DL 20T70 POWER SUPPLY DL 20T7 PUSH BUTTON INTERFACE DL 20T72 DOUBLE PUSH BUTTON DL 20T74 SMOKE DETECTOR DL 20T75 TEMPERATURE CONTROLLER DL 20T76 PRESENCE DETECTOR
More informationAn optional analog input module, Order no connected to a 6-pole system connector adds four more analog sensors to the device.
Application: The analog input 4gang RMD processes measured-value data supplied by analog sensors. Four analog transducers in any combination can be connected to the input. The analog input 4gang RMD evaluates
More informationDELTA profil wall switch, single UP 241/2 5WG AB_2
UP 241/2 5WG1 241-2AB_2 UP 241/3,with status LED 5WG1 241-2AB_3 UP 243/2 5WG1 243-2AB_2 UP 243/3,with status LED 5WG1 243-2AB_3 UP 245/2 5WG1 245-2AB_2 UP 245/3,with status LED 5WG1 245-2AB_3 UP 245/4,with
More informationKNX/EIB Intelligent Installation Systems
K-BUS R Shutter Actuator, 4fold User manual-ver. 1 AWBS-04/00.1 KNX/EIB Intelligent Installation Systems Conents 1. General ---------------------------------------------------------------------------------------------------------------------
More informationBST BuildingSystemsTrainer
_SMARThome _SMARThome Three-Phase Network Analyzer Board Smart Metering Photovoltaic modul Counter Smart Meter 01 05 Wind power Counter 01 Solar array Backup system Photovoltaic On Grid DC Feeding SCADA
More informationPOPP & Co. Pioneering Smart Homes
Product Catalog POPP & Co. Pioneering Smart Homes The name Popp stands for 80 years of reliable and affordable electrical engineering Made in Germany. As a pioneer of Z-Wave technology in Europe POPP is
More informationFunctional description. Use of the application program. GAMMA instabus Application program description. June C0 Sensor Switch
Use of the application program Functional description Product family: Product type: Manufacturer: Push button Push button, 1 4 fold Siemens The touch sensors have one, two or four vertically arranged pairs
More informationEAE KNX Room Control Unit Product Manual RCUXXYY
EAE KNX Room Control Unit Product Manual RCUXXYY RCU2018 RCU2016 RCU1212 RCU0808 RCU2000 RCU2000 RCU1200 RCU0800 Note: RCUXXYY where XX denotes the number of outputs and YY number of inputs. Index 1 General...
More informationSliding shutter control Aluminium shutters
Sliding shutter control Aluminium shutters Operating and maintenance instructions FOR THE USER Valid from 09.2011 E 916.3 Notes These operating instructions describe how to operate the EHRET sliding shutter
More informationEIB/KNX ENO Radio bus interface (32-channel)
EIB/KNX ENO Radio bus interface (32-channel) Interface between EnOcean and EIB/KNX, on-wall mounting (Quelle: EIBMARKT GmbH, Reference No.: N000406) Page 1 Application EIB/KNX ENO Radio bus interface acts
More informationDELTA i-system wall switch single UP 221/2 5WG AB_2
DELTA i-system wall switch single UP 221/2 5WG1 221-2AB_2 UP 221/3,with status LED 5WG1 221-2AB_3 wall switch double UP 222/2, 5WG1 222-2AB_2 UP 222/3,with status LED 5WG1 222-2AB_3 wall switch triple
More informationPower Supply System KNX PS640-IP
Power Supply System KNX PS640-IP with Ethernet Interface Installation and Adjustment Elsner Elektronik GmbH Steuerungs- und Automatisierungstechnik Herdweg 7 D-75391 Gechingen Germany Phone: +49 (0) 70
More informationDELTA style 6/1. 6/6 Introduction. 6/7 Frames. 6/8 Switches and pushbuttons. 6/14 Socket outlets. 6/16 International plug-and-socket devices
/ Introduction /7 Frames /8 Switches and pushbuttons /14 Socket outlets /1 International plug-and-socket devices /17 Shutter/blind controls /21 Lighting controls /24 Motion detectors /2 Room temperature
More informationclarity 3 Programmable Controller
clarity 3 Programmable Controller BACnet General Purpose Controllers (B-AAC) DESCRIPTION Taco Clarity 3 FPC series controllers are designed to control building systems and HVAC equipment. The integrated
More informationVersion 4 Controls for natural ventilation. WCC 310 / 320 PLUS MotorController
Version 4 Controls for natural ventilation WCC 310 / 320 PLUS 3.20 Natural ventilation Rated voltage MotorLink KNX product BACnet product Modbus product Application for daily comfort ventilation to be
More informationETATRACK active Frequently Asked Questions for Solar Park Applications. System Description. Tracking Movements. Elevation.
ETATRACK active 1500 Frequently Asked Questions for Solar Park Applications System Description - active single-axis tracking system for solar modules, with manually adjustable elevation angle (stepless
More information1/6 WI-FI VISTO KIT + POWER SUPPLY + BELL, USA AWARDS KIT VIDEO VISTO DOOR ENTRY SYSTEMS OVERVIEW VISTOKIT/U
1/6 OVERVIEW Kit composed of art. Visto (smart doorbell), 3532 (chime), 3534 (power supply). Italian designed smart doorbell wich allow audio/video communication from the door to the smartphone/tablet
More informationAutomatio made easy
Life made easy Automatio made easy n Comunello s Mowin project is based on our long experience with mechanical movement systems for windows and gates, developed since the company was founded in 1965. With
More informationWAGO Lighting Management The Lighting Control Solution Stay in Control of Your System
WAGO Lighting Management The Lighting Control Solution Stay in Control of Your System OUR CONCEPT The Solution for Efficient Lighting Management in Production Facilities and Warehouses Using a combination
More informationCONTENTS CONTROLLERS room controllers room units control units PRODUAL 3 CATALOGUE
Catalogue 207 CONTENTS CONTROLLERS... 4 room controllers... 5 room units... 29 control units... 24 PRODUAL 3 CATALOGUE T U R KU I C T C ON T R OL L E R S Multifunctional controllers for optimal performance
More informationUse of the application program
Use of the application program Product family: Product type: Manufacturer: Display Display units Siemens AG Name: Contouch Room Controller UP 204 Order no.: 5WG1 204-2AB11, titanium white, 5WG1 204-2AB21,
More informationUniversal Controller
3 342 Universal Controller For comfort control in HVAC & R-Systems Standalone electronic universal controller with P or PI response Operating voltage in accordance to type AC 24 V Control application selectable
More informationDDC110-L1.. DDC110-L4 technolon Room Module
technolon Room Module DDC110-L1, DDC110-L2, DDC110-L3 and DDC110-L4 Single room control or room display and service module for single-room control in the LON network. With display of the room temperature
More informationProduct Specifications
Product Specifications VIBROCONTROL 6000 Monitoring System Description of Functionality Overview The VIBROCONTROL 6000 Monitoring System is used for both stand-alone machine protection and condition monitoring
More informationHLS34 Modbus FCU/VAV Controllers installation instructions
HLS34 Modbus FCU/VAV Controllers installation instructions The HLS34 is specifically designed for individual room temperature and zone control applications. The controllers have built-in RS-485 channel
More informationUse of the application program
Use of the application program Product family: Product type: Manufacturer: Display Display units Siemens AG Name: Contouch Room Controller UP 204 Order no.: 5WG1 204-2AB11, titanium white, 5WG1 204-2AB21,
More informationABB i-bus KNX Blind/Roller Shutter Actuators JRA/S Product Manual
Blind/Roller Shutter Actuators JRA/S Product Manual Contents Contents Page 1 General... 3 1.1 Using the product manual...4 1.1.1 Structure of the product manual...4 1.1.2 Notes...5 1.2 Product and functional
More informationApplication description. KNX Push-button module 1gang. KNX Push-button module 2gang
Application description KNX Push-button module 1/2gang Electrical/mechanical data: see the operating instructions for the product Order number Product designation Application programme TP product Radio
More informationHigh-performance switching actuators
High-performance switching actuators Wide-ranging applications efficient installation and set-up operation for many years The worldwide standard for home and building control siemens.com/gamma Switching
More informationWireless Control Systems
Wireless Control Systems Leading the way in intelligent automation contents Range Overview Typical Installations Transmitters Combined Modules Receivers Accessories Programming Switching & Dimmer Functions
More informationapplication software
application software application software RF input product Electrical / Mechanical characteristics: see product user manual Product reference Product designation TP device RF devices 8565 52 xx 8565 62
More informationgesis FLEX Decentralized room automation Modular Compact Pluggable Room for the future.
gesis FLEX gesis FLEX Decentralized room automation Modular Compact Pluggable Room for the future. 2 gesis FLEX Room automation of the future Decentralized room automation with gesis FLEX In terms of flexibility,
More information7-day room temperature controller
s 2 205 7-day room temperature controller Heating or cooling applications REV24.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationCube LAN Gateway. Operating manual BC-LGW-O-TW
Cube LAN Gateway Operating manual BC-LGW-O-TW Package contents Package contents Quantity Item 1x MAX! Cube LAN Gateway 1x 1x 1x 1x 1x 3x Plug-in USB power supply USB cable Network cable Mounting accessories
More informationGas Controller System DGC-06
Page 1 May 2016 Measuring, warning and controlling device series for toxic, combustible and refrigerant gases and vapours. The gas controller series DGC-06 is designed in accordance with the standard EN
More informationGlu Home, Smart Home!
Glu Home, Smart Home! Product Catalogue 2018 www.myeglu.com acts as a communication gateway between all the eglu devices installed at home and your Wi-Fi router. It is a pluggable device and draws power
More informationCRM Control Panel and Weather Detection System CRM3 for DC actuators (part # 40821J) CRM4 for AC actuators (part # 40822K)
CRM Control Panel and Weather Detection System CRM3 for DC actuators (part # 40821J) CRM4 for AC actuators (part # 40822K) CRM Applications CRM includes a control relay box and a power supply; additional
More informationWeekday / weekend room temperature controller
s 2 203 Weekday / weekend room temperature controller Heating applications REV17.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationManual. animeo D Master Control W2 Ref Master Control W8 Ref Version 3.1 Revision date: Ref:
Manual animeo D Master Control W Ref. 1860187 animeo D Master Control W8 Ref. 1860193 Version 3.1 Revision date: 31.03.17 Ref: 510965 Somfy SAS 50 Avenue du Nouveau Monde 74300 Cluses France T +33 (0)4
More informationSection A5. Standard Telephone Entry Systems. This Price Schedule is effective April 1, Date Page Comment
April 2015 PRICE SCHEDULE A 2.0 Section A5 This Price Schedule is effective April 1, 2015. Date Page Comment 4-1-15 All April, 2015 Price Schedule update. Prices and specifications subject to change without
More informationManual. animeo D Master Control W2 Ref Master Control W8 Ref Version 3.1 Revision date: Ref:
SOMFY ACTIVITES SA Société Anonyme, capital 35.000.000, RCS Annecy 303.970.30 Manual Manual animeo D Master Control W Ref. 1860187 animeo D Master Control W8 Ref. 1860193 Version 3.1 Revision date: 31.03.17
More informationDisplay devices. Functional versatility with optimum ease of use
Display devices Functional versatility with optimum ease of use KNX Smart-Pilots Intuitive operation via resistive touch screen With the fanless SMART PILOT PC for wall mounting, you control all the building
More informationApplication program: description and examples
F a n C o i l U n i t C o n t r o l l e r F a n C o i l 4 9 5 5 1 Application program: description and examples Woertz AG Electrotechnical accessories, installation systems Hofackerstrasse 47, P.O. Box
More informationThe output variables can be force-controlled from a coordinating control system.
Produktname: 4-channel analog actuator Bauform: rail-mounted device Artikel-Nr.: 1022 00 ETS-Suchpfad: Gira Giersiepen / Output / Analog output 4fach / Analog actuator 4fach Scope of application: The analog
More information