Speed indicator DR 1010 Revolution per minute - speed - flow

Transcription

1 Speed indicator DR 1010 Revolution per minute speed flow Features M LEDDisplay 14.2 mm red M Display range M decimal points or floating point programmable M Inputs for switching contacts, pnpinitiators and Namurinitiators M Programmable inputprescaler M Time base min 1 M Integrated transmittersupply 24/8 V DC M Holdinput M Max. 2 outputs, SPDT relay M Field case with snap lid, 2 x M16x1.5 other cable glands see Option 09 or on request M Protection IP65 General The Speed Indicator DR1010 has been designed for field applications in process control and automation. Parameters for operation mode can be programmed. The DR1010 can be used wherever processes based per minute just as speed should be measured and displayed. Short information Programming Transmittersupply Input prescaler Alarm outputs Holdfunction Parameters are programmed via frontside membrane keypad The integrated transmitter supply allows direct connection of pnp initiators, light barriers, mechanical switch contacts, proximity switches, rotary encoder (24 V DC) and Namur initiators (8 V DC). An input prescaler function for both inputs is programmable. Alarm outputs can be programmed as continues contact or pulse contact. Switching performance min. or max., hysteresis, ondelay time and offdelay time are programmable in range from 1 s up to 9 h. Freezing the display by control voltage 24 V DC or voltage free contact. For more features like math functions summing, difference and display conversion, etc. please choose ProductivityMeter PR

2 Technical data Power supply Supply voltage : 230 V AC ±10 %; 115 V AC ±10 %; 24 V AC ±10 % or 24 V DC ±15 % Power consumption : max. 3.5 VA Operating temperature : C/ F, Standard (extended temperature range on request) Rated voltage : 250 V~ acc. VDE 0110 between input/output/supply voltage overvoltage category III Test voltage : 4kV=, between input/output/supply voltage conformity : EN55022, EN60555, IEC /4/5/11/13 Input pnp input : Ri = 6.3 kω level: < 4 V low; > 8.5 V high; hysteresis > 2.5 V, max. 35 V Namur input : Ri appr. 1 kω (<4 ma) level: < 1 ma low; >2.2 ma high; hysteresis > 0.5 ma max. 35 V Counting frequence max. : Input E1 = 1 Hz Hz, (switch contact) Input E2 = 1 Hz khz, (pnpinitiator or Namur) Accuracy : %, ±1 Digit Min. pulse width : Electronic pulse 50 μs, switch contact 5 ms Transmitter supply : 8 V DC (Namur), 24 V DC (pnp), Ri appr. 150 Ω, max. 50 ma Display : LED red, 14.2 mm Indicating range : Digit with leading zero suppression Additional display : LED 2digit red, 7 mm (parameter and output indicator ) Output Relay : SPDT <250 V AC <250 VA <2 A, <300 V DC <50 W <2 A Field case : Material PA6GF 15/15 Weight : max. 350 g Connection : Clamp terminals, 2 mm² wire, 1.5 mm² flexible wire, AWG14 Protection : Front IP65, terminals IP20, fingersafe acc. BGV A3 Dimensions Option 09 1 x M20x1.5 Multi (2 x Ø=6 mm) 1 x M20x1.5 2 x M16x1.5 (In the base on request) 2

3 Legend (open lid) Terminal strip Terminal 1 and 13 not marked Connection diagram Alarm outputs E1 (30 Hz) E2 (15 khz) GND Hold +24/8 V max. 50 ma 250 V AC < 250 VA <2 A 300 V DC < 50 W < 2 A A1 A2 Switch contact NamurInitiator (8 V DC) Supply voltage e.g. 230 V AC PNPInitiator rotary encoder (24 V DC) 3

4 Controls and indicators Process value Field for additional text Parameter display or activated preselect outputs Description Unitfield Parameter button Down button Up button. For se Operation of the device is arranged in 2 levels. The requested parameter can be called by button lection within a parameter or for entering data, use buttons and. Button combinations: + 1 parameter back + setting parameter to zero or minimum value After switching on the supply voltage, the device is located in the Working level. Setpoint of the alarm outputs can be adjusted. Pressing the button for more than 2 seconds, activates the Configuration level. Now all the parameters which definines the function of the device can be programmed. After finishing the configuration or when no button was pushed for more than 2 minutes, the program returns to the working level. Leaving the configuration level is possible at any time by pressing the button for more than 2 seconds. Parameter display as status indicator for the alarm outputs A1A2. Error codes: Segments f (A1) and/or b (A2) are flashing with 2 Hz, when delay time is active. Segments e (A1) and/or c (A2) are output indicators. Reading this message in the parameter display a parameter failure has been occured. The display flashes. By pressing one of the buttons, the error code will be deleted and a copy of the factory settings will be reloaded to the EEPROM. The device will work with the factory settings. If this copy doesn t work, please ship the device for factory repair. Parameter lock active. See configuration page 7. Overflow Startup note: Before the device can be used, it must be configured for the intended use. see page 5 4

5 Notes to representation Parameter is only displayed when configurated Parameter is only displayed when feature is included (see order code) Please Note: All parameters can be called if they are not blocked by other programmed parameters and if they are available. Factory settings are shown in the configuration level in the display. Working level Button Display Description Process value Output indication (only if installed and activated). Setpoint alarm output A1 Setting possible from... Digit Setpoint alarm output A2 Setting possible from... Digit with buttons und. 5

6 Configuration Button Display Description (Display graphic shows factory settings) Press 2s 1 Transmitter supply / input level : 24V DC für pnpinitiators : 8V DC für NamurInitiators* (* with ext. 5V supply also useful for TTLsignals) : only for factory settings Selection 2 Prescaler for input E1 and E2 Setting possible from...digit (Only every n th pulse is displayed) 3 Decimal point position : floating point : 3 decimals : 2 decimals : 1 decimal : non Maximum 3 decimal point positions possible. In the mode the decimal point changes automatically if the process value > digit Selection 4 Digital filter Selection with button and. 5 Switching performance for alarm output A1 (min) : cont. contact on off (max) : cont. contact off on Selection 6 Setpoint for alarm output A1 Setting possible from... Digit ( mode settings without decimals) 7 Hysteresis for alarm output A1 Setting possible from... digit ( mode settings without decimals). continue page 7 6

7 Button Display Description (Display graphic shows factory settings) 8 Switchon delay time for alarm output A1. Setting possible from... (h.mm.ss) 9 Switchoff delay time for alarm output A1. Setting possible from... (h.mm.ss) 10 Switching performance for alarm output A2 (min) : cont. contact on off (max) : cont. contact off on Selection 11 Setpoint for alarm output A1 Setting possible from... Digit ( mode settings without decimals) 12 Hysteresis for alarm output A2. Setting possible from... digit ( mode settings without decimals). 13 Switchon delay time for alarm output A2. Setting possible from... (h.mm.ss) 14 Switchoff delay time for alarm output A2. Setting possible from... (h.mm.ss) 15 Parameter lock : no lock : configuration level locked : all parameters locked Selection Return to the working level 7

8 Ordering code DR Input 1 2 pulse inputs, integrated transmitter supply, hold input 2. Alarm output 00 not installed 2R 2 alarm outputs relay SPDT 3. Supply voltage V AC V AC 4 24 V AC 5 24 V DC ± 10 % 5060 Hz ± 10 % 5060 Hz ± 10 % 5060 Hz ± 15 % 4. Option without option 1 x M20x1.5 Multi (2 x Ø6mm), 1 x M20x Unit (appears in the unit field) 6. Additional text (will be placed in the field for additional text, max. 3 x 70 mm, WxH) Custom confuguration on request 8 10/04V1.600