Super Skwisher. Ross Compressor +++
|
|
- Arline Byrd
- 5 years ago
- Views:
Transcription
1 Super Skwisher Ross Compressor +++ Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved.
2 Important notes If you re using any of our footswitch daughterboards, DOWNLOAD THE DAUGHTER DOCUMENT Download and read the appropriate build document for the daughterboard as well as this one BEFORE you start. DO NOT solder the supplied Current Limiting Resistor (CLR) to the main circuit board even if there is a place for it. This should be soldered to the footswitch daughterboard. COMPONENT SPECS Unless otherwise stated in this document: Resistors should be 0.25W. You can use those with higher ratings but check the physical size of them. Electrolytics caps should be at least 25V for 9V circuits, 35V for 18V circuits. Again, check physical size if using higher ratings. LAYOUT CONVENTIONS Unless otherwise stated in this document, the following are used: Electrolytic capacitors: Long leg (anode) to square pad. Diodes: Striped leg (cathode) to square pad. ICs: Square pad indicates pin 1.
3 Schematic - full board The schematic above shows everything that is on the PCB. Since the board is designed for several different builds, not everything is used on each build. The following pages will show only the parts of the schematic relevant to each particular build, though components not shown will still be referenced in the BOM where a jumper is required or it is left empty. The cover image shows the previous version of the PCB, prior to the addition of the LM Actual layout is below. CA3080 goes into the pads marked in blue, LM13700 in red. See page 8 for a shot of a build on the latest PCB. PCB Layout 2015 Pedal Parts Ltd. All rights reserved. General Notes The power and signal pads on the PCB conform to the FuzzDog Direct Connection format, so can be paired with the appropriate daughterboard for quick and easy offboard wiring. Be very careful when soldering the diodes. They re very sensitive to heat. You should use some kind of heat sink (crocodile clip or reverse action tweezers) on each leg as you solder them. Keep exposure to heat to a minimum (under 2 seconds). You should use a socket for the IC, or be super careful not to overheat. Take your time. Snap the small metal tag off the pots so they can be mounted flush in the box. Though the LM13700 isn t shown on the schematic, it can simply replace the CA3080 in the build. Place it in the IC2 position. The legs correspond like this: CA3080 LM As long as you put your LM13700 in the pads shown left it s all done for you.
4 Stock Ross Compressor R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 2M2 470K 470K 220K 220K 15K 150K 27K 150K Jumper 56K 27K 2K2 (CLR) *100p will remove less treble than stock. **Originally linear (B), but reverse-log (C) is better. Put a jumper wire between pads of CLIP. To set the trimmer turn the Sustain pot up to full and adjust trim for maximum sustain with no distortion. C1 C2 220p* C3 C4 C5 C6 10u C7 C8 10u C9 10u C10 C11 C12 C13 47n C14 C15 1n C16 C17 C18 D1 1N4001 D2,3 1N4148 Q1-5 2N5089 IC T1 CA3080 2K2 SUST 500KB/C** LEVEL 50KA CLIP Jumper ATTACK S1
5 Mark Hammer Mods R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 2M2 470K 470K 220K 220K 15K 150K 27K 150K 56K 27K 2K2 (CLR) 39K See notes from previous page. The SPDT switch will give you three different recovery settings. C17 will give more treble response. C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 220p 10u 10u 10u 47n 1n 1n5 D1 1N4001 D2,3 1N4148 Q1-5 2N5089 IC T1 CA3080 2K2 SUST 500KB/C LEVEL 50KA CLIP Jumper 1+2 ATTACK S1 SPDT ON-OFF-ON
6 Boutique 4-Knob R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 4M7 470K 470K 220K 220K 15K 150K 27K Jumper 56K 27K 2K2 (CLR) *In the original unit T1 is replaced by two 1K resistors. A 2K2 trimmer set in the middle position will give the same result and allow extra adjustment. **150KB will be hard to source. See notes on next page. C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 150p tant 10u 10u 47n 1n 2n2 D1 1N4001 D2,3 1N4148 Q1-5 2N3904 IC CA3080 T1 2K2* SUST LEVEL CLIP ATTACK S1 500KC 50KB 150KB** 150KB**
7 These are the CLIP pads that need jumpering on the Stock and Hammer builds. Those awkward 150KB Pots... Not something that s on every supplier s stock list, so will be difficult to source. You have couple of options here: Use 250KB and live with it. You get extra adjustment range that you may or may not find useful. It s not the end of the world. Use 250KB and add resistors in parallel to get closer to 150KB. This will, unfortunately, change the sweep of the pot which may make it less useable than the extra range given by the first option. The good thing is, you can try option 1, add the resistors and see how it works, then simply snip them back off if you don t like it. To add the resistors, just solder them across pads 1 & 3 of both pots as shown. A 250K pot in parallel with a 390K resistor will give you 152K. Close enough! Replace the trimmer Place the two 1K resistors for the 4-knob version like this>>>
8 ...and here s a build on the newer PCB with the LM This is a two-knob with Hammer mods switch. Note: the CLIP jumper has changed position since this build.
9 Test the board! Check the relevant daughterboard document for more info before you undertake this stage. UNDER NO CIRCUMSTANCES will troubleshooting help be offered if you have skipped this stage. No exceptions. Once you ve finished the circuit it makes sense to test is before starting on the switch and LED wiring. It ll cut down troubleshooting time in the long run. If the circuit works at this stage, but it doesn t once you wire up the switch - guess what? You ve probably made a mistake with the switch. Solder some nice, long lengths of wire to the board connections for 9V,, IN and OUT. Connect IN and OUT to the jacks as shown. Connect all the s together (twist them up and add a small amount of solder to tack it). Connect the battery + lead to the 9V wire, same method. Plug in. Go! If you re using a ribbon cable you can tack the wires to the ends of that. It s a lot easier to take them off there than it is do desolder wires from the PCB pads. If it works, carry on and do your switch wiring. If not... aw man. At least you know the problem is with the circuit. Find out why, get it working, THEN worry about the switch etc. Your completed circuit board including pots
10 Wire it up - DC only version (if using a daughterboard please refer to the relevant document) INPUT IN 9V L L E E D D + OUT LED+ OUT This circuit is standard, Negative. Your power supply should be Tip Negative / Sleeve Positive. That s the same as your standard pedals (Boss etc), and you can safely daisy-chain your supply to this pedal. The connections don t all have to connect to one point. They can be daisy-chained around the circuit, using larger connection points (such as jack socket lugs) for multiple connections. As long as they all connect together in some way.
11 Wire it up - with battery (if using a daughterboard please refer to the relevant document) INPUT IN 9V + BATTERY L L E E D D + OUT LED+ OUT Just because the FuzzDog enclosure won t take a battery, there s nothing stopping you using a bigger box. This circuit is standard, Negative. Your power supply should be Tip Negative / Sleeve Positive. That s the same as your standard pedals (Boss etc), and you can safely daisy-chain your supply to this pedal. The connections don t all have to connect to one point. They can be daisy-chained around the circuit, using larger connection points (such as jack socket lugs) for multiple connections. As long as they all connect together in some way. FuzzDog.co.uk
12 Drilling template Hammond 1590B 60 x 111 x 31mm Recommended drill sizes: Pots 7mm Jacks 10mm Footswitch 12mm DC Socket 12mm Toggle Switch 6mm It s a good idea to drill the holes for the pots 1mm bigger to give yourself some wiggle room, unless you re a drill ninja. 32mm 27mm 14mm This template is a rough guide only. You should ensure correct marking of your enclosure before drilling. You use this template at your own risk. Pedal Parts Ltd can accept no responsibility for incorrect drilling of enclosures. FuzzDog.co.uk
Cherub Chorus. Wobbly fun based on Rick Holt s Little Angel
Cherub Chorus Wobbly fun based on Rick Holt s Little Angel Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights
More informationIC Big Muff 78. Chip-based Big Muff Pi. Smooooooth!
IC Big Muff 78 Chip-based Big Muff Pi. Smooooooth! Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved.
More informationLittle Screamerv2.0. Stripped-back, bufferless Tube Screamer
Little Screamerv2.0 Stripped-back, bufferless Tube Screamer Contents of this document are 2016 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All
More informationDeep Vibes. Wobbly Optical Vibe action
Deep Vibes Wobbly Optical Vibe action Contents of this document are 2018 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved. Important
More informationFuzz Rite V2.0. Mosrite FuzzRite / Gus Rite Fuzz
Fuzz Rite V2.0 Mosrite FuzzRite / Gus Rite Fuzz Contents of this document are 2016 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved.
More informationFilthy Fack! Famous germanium 5-knobbed fuzz clone
Filthy Fack! Famous germanium 5-knobbed fuzz clone Contents of this document are 2014 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved.
More informationEchoBlue Delay. PT2399 Delayayayayayay v3.0
EchoBlue Delay PT2399 Delayayayayayay v3.0 Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved.
More informationAstroTone. Clone of the Astro Tone Fuzz / Sam Ash Fuzzz Boxx
AstroTone Clone of the Astro Tone Fuzz / Sam Ash Fuzzz Boxx Contents of this document are 2016 Pedal Parts td. No reproduction permitted without the express written permission of Pedal Parts td. All rights
More informationLunar Shot Trem. CultureJam s Shoot The Moon - a stripped back Tremulus Lune
unar Shot Trem CultureJam s Shoot The Moon - a stripped back Tremulus une Contents of this document are 2017 Pedal Parts td. No reproduction permitted without the express written permission of Pedal Parts
More informationBox Of Tone 50. Boutique Boost/Overdrive
Box Of Tone 50 Boutique Boost/Overdrive Contents of this document are 2016 Pedal Parts td. No reproduction permitted without the express written permission of Pedal Parts td. All rights reserved. Schematic
More informationTone Bender Mk III. Grandaddy of super-cool vintage fuzz tone
Tone Bender Mk III Grandaddy of super-cool vintage fuzz tone Contents of this document are 2014 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All
More informationFuzz Face. Vintage fuzz with optional voltage inverter
Fuzz Face Vintage fuzz with optional voltage inverter Contents of this document are 2014 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights
More informationMini Fuzz Face. Vintage fuzz in a neat little package
Mini Fuzz Face Vintage fuzz in a neat little package Contents of this document are 2016 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights
More informationFuzzD s 3PDT Direct Connect DaughterBoard
FuzzD s 3PDT Direct Connect DaughterBoard Minimising your wiring woes Contents of this document are 2015 Pedal Parts Ltd. No reproduction permitted without the express written permission of Pedal Parts
More informationSnail Gear Building instructions V1.0
Snail Gear Building instructions V1.0 Table of contents Components... 3 PCB layout... 4 General guideline for components... 5 General building tips... 5 Modifications... 6 Biasing... 7 Off board wiring...
More informationQUANTOM DEFRAKULATOR Build Document last updated june 2018 for PCB version 1.0
QUANTOM DEFRAKULATOR Build Document last updated june 2018 for PCB version 1.0 The Quantom Defrakulator is a drone synthesizer with 3 square wave oscillators and one LFO (low frequency oscillator). Each
More informationSTRATUS PROJECT NAME. BASED ON Ibanez TS-9 Tube Screamer. BUILD DIFFICULTY Easy. DOCUMENT VERSION Overdrive ( ) EFFECT TYPE
PROJECT NAME STRATUS BASED ON Ibanez TS-9 Tube Screamer BUILD DIFFICULTY Easy EFFECT TYPE DOCUMENT VERSION Overdrive 1.0.0 (018-09-) PROJECT SUMMARY The quintessential mid-hump overdrive pedal made famous
More informationPROJECT SUMMARY A reproduction of a rare and very expensive low-to-mid-gain overdrive with 3-band EQ that is popular in the Nashville scene.
PROJECT NAME QUANTUM BASED ON Ibanez MT-0 Mostortion BUILD DIFFICULTY Easy EFFECT TYPE DOCUMENT VERSION Overdrive / Distortion.0.0 (08--5) PROJECT SUMMARY A reproduction of a rare and very expensive low-to-mid-gain
More informationUF-3701 Power Board Construction Guide
Page 1/5 Soldering and Part Placement See the Chapter 3 of the MIT 6270 Manual for information on electronic assembly, including soldering techniques and component mounting. Construction Information All
More informationTEMPEST PROJECT NAME. BASED ON Friedman BE-OD / Dirty Shirley. BUILD DIFFICULTY Intermediate. DOCUMENT VERSION Amp-Like Distortion 1.0.
PROJECT NAME TEMPEST BASED ON Friedman BE-OD / Dirty Shirley BUILD DIFFICULTY Intermediate EFFECT TYPE DOCUMENT VERSION Amp-Like Distortion.0. (09-0-08) PROJECT SUMMARY A pedal recreation of the Friedman
More informationHALO. Easy. Distortion / Sustainer, Fuzz ( )
PROJECT NAME HALO BASED ON Electro-Harmonix Big Muff Pi BUILD DIFFICULTY Easy EFFECT TYPE DOCUMENT VERSION Distortion / Sustainer, Fuzz 1.0.0 (2018-07-04) PROJECT SUMMARY One of the most classic guitar
More informationHave Mercy Building instructions v1.1
Have Mercy Building instructions v1.1 Table of contents Have Mercy v1.1 PCB layout... 3 Components... 4 Power section... 5 Build sequence... 5 Calibration... 6 Off board wiring... 6 Potentiometers... 6
More informationElectronics Construction Manual
Electronics Construction Manual MitchElectronics 2018 Version 1 07/05/2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors
More informationB.Y.O.C. MK2 Kit Instructions
B.Y.O.C. MK2 Kit Instructions Parts Checklist.....page 2 Populating the Circuit Board......page 3-5 Assembly......page 6 Wiring......page 7 Installing the LED and Mounting the PCB...page 8-9 Finish up...page
More informationConstruction Construction Instructions
Semi-Virtual Diskette SVD Construction Construction Instructions PCB version 2.0 September 2004 Eric J. Rothfus Table of Contents Table of Contents... i Parts List...1 Construction Overview...5 PCB Construction...
More informationMONAD PROJECT NAME. BASED ON Univox Uni-Drive UD-50. BUILD DIFFICULTY Beginner. DOCUMENT VERSION Boost ( ) EFFECT TYPE
PROJECT NAME MONAD BASED ON Univox Uni-Drive UD-50 BUILD DIFFICULTY Beginner EFFECT TYPE DOCUMENT VERSION Boost 1.0.0 (2018-12-15) PROJECT SUMMARY A basic 3-transistor booster that gets some grit at higher
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationPROJECT SUMMARY A flexible drive pedal that can go from clean volume boost to smooth overdrive. Includes a 2-band tone stack for treble & bass.
PROJECT NAME MALACANDRA BASED ON Xotic BB Preamp BUILD DIFFICULTY Easy EFFECT TYPE DOCUMENT VERSION Boost / Overdrive 1.0.0 (2018-09-22) PROJECT SUMMARY A flexible drive pedal that can go from clean volume
More informationPROJECT SUMMARY A flexible drive pedal that can go from clean volume boost to smooth overdrive. Includes a 2-band tone stack for treble & bass.
PROJECT NAME PERELANDRA BASED ON Xotic BB Preamp BUILD DIFFICULTY Easy EFFECT TYPE DOCUMENT VERSION Boost / Overdrive.0.0 (08-09-) PROJECT SUMMARY A flexible drive pedal that can go from clean volume boost
More informationPROJECT SUMMARY A classic untamed fuzz from the 1970s that adds an octave-up overtone, famous for its use by Pete Townshend of The Who.
PROJECT NAME RIFT BASED ON Univox Superfuzz BUILD DIFFICULTY Intermediate EFFECT TYPE DOCUMENT VERSION Octave Fuzz 1.0.0 (2019-02-01) PROJECT SUMMARY A classic untamed fuzz from the 1970s that adds an
More informationBuild Your Own Clone Optical Compressor Kit Instructions
Build Your Own Clone Optical Compressor Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More informationElectronics Construction Manual
Electronics Construction Manual MitchElectronics 2019 Version 3 04/02/2019 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationSTAGE INTERCOM KIT 1.1 SPECIFICATION. General: The lower section is a small power amplifier designed to drive headphones or a small 8ohm speaker.
STAGE INTERCOM KIT Version 2.1.1 - March 2018 - EduTek Ltd 1.0 DESCRIPTION This intercom module comprises of two separate circuits sharing the same supply. The upper section is a pre-amplifier designed
More informationThe Sudden Storm Kit. by QRPme. Builder s Guide. version4.2. for. Sudden Storm ][ Ver4 (red pcb) Updated 01/10/2012
The Sudden Storm Kit by QRPme Builder s Guide version4.2 for Sudden Storm ][ Ver4 (red pcb) Updated 01/10/2012 Open the can and the adventure begins 1 Organize the parts and take an inventory Bill of Materials
More informationGRAVITON. Intermediate. Metal Distortion ( )
PROJECT NAME GRAVITON BASED ON BOSS HM- Heavy Metal BUILD DIFFICULTY Intermediate EFFECT TYPE DOCUMENT VERSION Metal Distortion.0.0 (08-07-04) PROJECT SUMMARY A unique distortion effect favored by extreme
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationMini B lue M idnight
Mini Blue Midnight 2011 by Shattered Glass Audio. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording,
More information[Note: Power adapter is not included in the kits. Users need to prepare a 9 12 V ( >300mA capacity ) DC power supply]
062 LCD Oscilloscope Assembly Notes Applicable Models: 06203KP, 06204KP DN062-18v02 Important Notes 1. Some components shown in the schematic and PCB layout are for options or adjustments. They do not
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationMAIN PCB (The small one with the square cut out from one side)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationAdvanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit
Advanced LED Lantern 1.0 Instruction Manual Eastern Voltage Research, LLC Introduction to the Advanced Lantern 1.0 Kit Thank you for purchasing the Advanced Lantern 1.0 Kit. This kit is an advanced microprocessor
More informationThe Basic Counter. Hobby Electronics Soldering Kit. Instruction Guide
The Basic Counter Hobby Electronics Soldering Kit Instruction Guide TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required:
More informationdual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03
dual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03 Contents Contents... 2 Introduction... 3 Part Sourcing Notes for Non Kit Builders... 3 Eurorack Kit Assembly... 4 Resistors and
More informationUniversal Keying Adapter 3+
Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port
More informationKDS Channel DMX Controlled Servo Kit
KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an
More informationFX TYPE: FUZZ PCB artwork m2010 madbeanpedals Release date: REVISED:
http://www.madbeanpedals.com presents zygote FX TYPE: FUZZ PCB artwork m2010 madbeanpedals Release date: 12.10.10 REVISED: 03.24.11 The Zygote is an all in one fuzz. It allows you to build several types
More informationUber Tuber FX TYPE: Tube Overdrive 2018 madbeanpedals. Important stuff:
Uber Tuber FX TYPE: Tube Overdrive 2018 madbeanpedals Important stuff: The UberTuber is a tube-based overdrive. It requires an 18v 500mA (min.) power supply. I suggest the Dunlop 18v supply if you do not
More informationQUASAR ELECTRONICS KIT No Hi-Fi PREAMPLIFIER WITH REMOTE CONTROL
QUASAR ELECTRONICS KIT No. 1070 Hi-Fi PREAMPLIFIER WITH REMOTE CONTROL General Description This is a hi-fi STEREO preamplifier based on a single integrated circuit which employs a revolutionary new method
More informationIf you have any questions and would like to get in touch my is
Ghost Effects Lunar Incantation PCB Guide. Thank you for buying a Ghost Effects Lunar Incantation PCB, the circuit is a version of the Mosrite Fuzzrite circuit with the addition of the 'Tone' control from
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationAUDIO AMPLIFIER PROJECT
Intro to Electronics 110 - Audio Amplifier Project AUDIO AMPLIFIER PROJECT In this project, you will learn how to master a device by studying all the parts and building it with a partner. Our test subject:
More informationFieldKit DIY Manual Author: Otto Mikkonen Last updated:
FieldKit DIY Manual Author: Otto Mikkonen Last updated: 11.04.2017 Required Materials - 1 x FieldKit PCB - 1 x FieldKit Front Panel - 1 x FieldKit Wooden Enclosure (Bottom + Lid) - 4 x Small Bottom Pad
More informationPARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 10kΩ Resistor OTHER PARTS YOU MAY NEED
PARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 150Ω Resistor 36 x 10kΩ Resistor 17 x Mini Toggle on-off 8 x Mini Toggle (on)-off-(on) 1 x 470Ω Resistor 1 x 47µF
More information3PRR. FX TYPE: Utility 2015 madbeanpedals W x 1.11 H change-log: Removed 10R current limiting resistor.
3PRR FX TYPE: Utility 2015 madbeanpedals 1.815 W x 1.11 H 2015 change-log: Removed 10R current limiting resistor. This PCB is designed for the typical BLUE 3PDT footswitch. Other footswitches may or may
More informationCreep Cluster Build Document. V5 - November 2018
Creep Cluster Build Document. V5 - November 2018 Dual triangle oscillators are hard-switched by a fast squarewave. Then the signal goes into a resonant lowpass filter. Sounds vary from deep rumbling drones
More informationtonefiend DIY CLUB Project 2 Build the Bulk Fuzz (based on Christian H. s Bazz Fuss Circuit) v02, by Joe Gore
Project 2 Build the Bulk Fuzz (based on Christian H. s Bazz Fuss Circuit) v02, 02.26.12 1 Here s the plan: This is a very fun project! When the smoke has cleared (and the smoke alarm has been reset), you
More informationContents Copyright 2013 By Small Bear Electronics LLC
The last piece of pre-assembly before you put everything together is creating the connector for the stomp switch and soldering those components together. Find the six-position Molex connector and the terminated
More informationHigh Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
More informationGuitarPCB.com Mini-Me Chorus Build Instructions
GuitarPCB.com Mini-Me Chorus Build Instructions This compares to the popular Small Clone TM chorus, but includes modifications. The major difference between this circuit and the commercial pedal on which
More informationKDR00101 DMX Controlled Relay Kit
KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or
More informationAdvanced Strobe 1.0 Kit
Kit Instruction Manual Eastern Voltage Research, LLC December 2013, Rev 1 1 http://www.easternvoltageresearch.com Kit Introduction to the Kit Thank you for purchasing the Kit. If you are looking for a
More informationBuilding the VMW Time Circuitry Meter by Vincent M. Weaver 6 May 2014
Building the VMW Time Circuitry Meter http://www.deater.net/weave/vmwprod/hardware/time_circuit/ by Vincent M. Weaver 6 May 2014 1 Introduction This is a work in progress. I will update it as I complete
More informationAssembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.
NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationQRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction
QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a QRPometer. We hope you will enjoy building it and and find it a useful addition to
More informationKDR00301 DMX Controlled Relay Kit
KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationPicoTurbine Mark 8.3 Generator Field Controller Kit
PicoTurbine Mark 8.3 Generator Field Controller Kit Based on a design published in Home Power magazine by Richard Perez. Used with permission. Reprint of original article included with kit. An easy-to-build
More informationLab 0: Wire Wrapping Project: Counter Board
Lab 0: Wire Wrapping Project: Counter Board September 3, 2008 In this experiment, you will build a simple counter circuit that can be plugged into your breadboard. It will provide a set of TTL output signals
More informationDELUXE STEREO AMPLIFIER KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS DELUXE STEREO AMPLIFIER KIT Version 2.0 Build Instructions
More informationCV Arpeggiator Rev 2 Build Documentation.
CV Arpeggiator Rev Build Documentation. Last updated 8-0-03 The CV Arpeggiator is a modular synth project used for creating arpeggios of control voltage. It utilizes a custom programmed PIC 6F685 micro
More informationTuBbika SMR-4-PLUS voicecard
TuBbika SMR-4-PLUS voicecard Assembly instructions We assume you know soldering. If you don t, look first at this tutorial. Be patient! And if you have any doubt, head to the forum never be afraid to ask!
More informationGLiPIC Ver C Assembly manual Ver 1.0
GLiPIC Ver C Assembly manual Ver 1.0 Last Rev 1.1 Oct 30, 2001 Author: Ranjit Diol Disclaimer and Terms of Agreement As with any kit, only the individual parts supplied are guaranteed against defects and
More informationDigital Flame 1.0 Kit
Digital Flame 1.0 Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com Introduction to the Digital Flame 1.0 Kit Thank you for purchasing the Digital
More informationNoise Gate A noise reduction stomp box
Noise Gate A noise reduction stomp box The Noise Gate (NG) is a pedal for noise reduction. However, unlike other filters that changes how the instrument sounds, the Noise Gate blocks the noise when the
More informationRC Tractor Guy Controller V2.1 Assembly Guide
RC Tractor Guy Controller V. Assembly Guide Features 0 Push button inputs Dual axis thumb sticks with built-in push button Rotary encoders with built-in push button MCU Socket to suit Meduino Mega 560
More informationDigital Candle 1.0 Kit
Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com Introduction to the Kit Thank you for purchasing the Kit. This kit is definitely a favorite
More informationDIGWDF Ren-W Universal Assembly Guide
DIGWDF Ren-W Universal Assembly Guide Overview Before starting, be sure to read through the entire guide to familiarize yourself with the parts and parts locations. In many cases, you may not need to install
More informationLushOne Inca Synth Module Build Instructions
LushOne Inca Synth Module Build Instructions Getting started If you can build the LushOne base module then then building the Inca should be easy Remember: Accuracy and neatness is more important than speed
More informationBMC24. MIDI TO GATE CONVERTER DOCUMENTATION. This documentation is for use with the "Euro Style" bottom board.
BMC24. MIDI TO GATE CONVERTER DOCUMENTATION. This documentation is for use with the "Euro Style" bottom board. A. USING THE MIDI TO GATE CONVERTER B. PARTS LIST C. BUILDING INSTRUCTIONS D. SCHEMATICS Revision.
More informationPhysics 120/220 Lab Equipment, Hints & Tips
Physics 120/220 Lab Equipment, Hints & Tips Solderless Breadboard... 2 Power supply... 4 Multimeters... 5 Function generator... 5 Oscilloscope... 6 10X probe... 7 Resistor color code... 7 Components...
More informationAn open-source hardware+software project. For design files and additional documentation, please visit:
An open-source hardware+software project. For design files and additional documentation, please visit: http://www.evilmadscientist.com/go/diavolino Support: http://www.evilmadscientist.com/forum/ Distributed
More informationKAA Watt x 2 Class-D Audio Amplifier Kit
KAA10021 50 Watt x 2 Class-D Audio Amplifier Kit This amplifier kit uses Texas Instruments TPA3116D2 stereo audio amplifier IC for driving speakers up to 50 watts @ 4 ohm per channel in stereo mode and
More informationStorage Card Interface Kit
Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3K The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve
More informationTHOMEEQUE'S EM3207 (v1.1)
THOMEEQUE'S EM3207 (v1.1) MN3207 based EHX Electric Mistress (9V) clone BUILD INSTRUCTIONS *DRAFT1* Thomeeque, 2011-06-03 INTRODUCTION EM3207 is a loose clone of the original 9V EHX Electric Mistress chorus/flanger
More informationEE 354 August 1, 2017 Assembly of the AT89C51CC03 board
EE 354 August 1, 2017 Assembly of the AT89C51CC03 board The AT89C51CC03 board comes as a kit which you must put together. The kit has the following parts: No. ID Description 1 1.5" x 3.25" printed circuit
More informationLED Sequencer 1.0 / 1.5
LED Sequencer 1.0 / 1.5 Instruction Manual Eastern Voltage Research, LLC May 2012, Rev 2 1 http://www.easternvoltageresearch.com Introduction to the LED Sequencer 1.0 Thank you for purchasing the LED Sequencer
More informationAssembly Instructions for the KA Electronics Elliptic Equalizer
Assembly Instructions for the KA Electronics Elliptic Equalizer Install IC sockets Elliptic Equalizer PC Board Stuffing Guide Place the PC Board on the work bench silkscreen side face up. Place twelve
More informationQUASAR KIT No DIGITAL DOWN TIMER 99 MIN WITH PIC
QUASAR KIT No 1173 - DIGITAL DOWN TIMER 99 MIN WITH PIC KIT 1173 is a digital countdown timer based on a micro controller, thus securing reliability and excellent operation under any circumstances. It
More informationSERGE Dual Extended ADSR 2017
SERGE Dual Extended ADSR 2017 The Serge Dual Extended ADSR module contains 2 identical Extended ADSR sections, each consisting of a main pcb and a panel pcb: Please note: Orientation of the main pcb: power
More informationAssembly of the TACOS WAT-910BD Housing v2
1) Circuit Diagram 2) Assembly of PCB a)tools Required. Only simple hand tools are necessary to complete the assembly of the PCB. - Soldering Iron and solder - Needle nose pliers - Wire clippers/trimmers
More informationsolutions for teaching and learning
Circuit Construction Op-Amp Comparator Project The circuit diagram on the right is the circuit for your project, it is called an op-amp comparator circuit, it is called a comparator circuit as it compares
More informationAssembly Instructions for the KA Electronics IGFO Input Gain Filter Output Board
Assembly Instructions for the KA Electronics IGFO Input Gain Filter Output Board IGFO PC Board Stuffing Guide Install IC sockets Place the PC Board on the work bench silkscreen side face up. Place ten
More informationsolutions for teaching and learning
RKOneAnalogue Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKOneAnalogue Software Development PCB Page 1 Description The RKOneAnalogue software development PCB has been
More informationMP3 audio amplifier. Build Instructions. Issue 2.0
MP3 audio amplifier Build Instructions Issue 2.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB). The components
More informationREFRACTOR. Intermediate. Overdrive ( )
PROJECT NAME REFRACTOR BASED ON Klon Centaur / KTR BUILD DIFFICULTY Intermediate EFFECT TYPE DOCUMENT VERSION Overdrive.0. (08-0-4) PROJECT SUMMARY A part-for-part replica of a mythical overdrive effect
More informationButterfly Laser Diode Mount
LM14S2 Butterfly Laser Diode Mount Operating Manual LM14S2 Laser On TEC Driver LD Driver THORLABS, Inc. Ph: (973) 579-7227 435 Route 206N Fax: (973) 383-8406 Newton, NJ 07860 USA www.thorlabs.com 10614-D02
More informationsolutions for teaching and learning
RKAmp1 Component List and Instructions PCB layout Constructed PCB Schematic RKAmp1 Stereo Amplifier Page 1 Description The RKAmp1 stereo amplifier PCB has been designed around the 2 x 1watt stereo amplifier
More information