Walk-and-Talk Interactive Panel

Transcription

1 Walk-and-Talk Interactive Panel Installation and Operation Guide Part number PolyVision Corporation All rights reserved

2 Information in this document is subject to change without notice. Reproduction in any manner without written permission of PolyVision Corporation is forbidden. PolyVision Corporation reserves the right to make changes in product design, or detail, and to discontinue any product or material without notice. This product is covered by one or more of the following patents: Canada 2,100,624; EPO 600,576; EPO 871,935; Germany 69,321,445; US 4,777,329; US 5,248,856; US 5,327,161; US 5,434,370; US 5,583,323; US 5,585,605; US 5,665,942; US 5,790,114; US 5,838,309 US 6,353,193; US 6,355,895; US 6,445,384; Other patents pending. PolyVision is a registered trademark of Steelcase, Inc. Walk-and-Talk is a trademark of PolyVision Corporation. All other registered trademarks and trademarks used herein are the property of their respective owners.

3 Table of Contents Overview Options and Considerations Installing the Interactive panel What Comes in the Box Connecting Cables Preparing to Connect Cables Connecting Cables Extending Remote Control Reception Preparing the Interactive Panel for Use Adjusting the Tilt of the Panel The Interactive Panel Control Buttons Getting Started with the Interactive Panel Using the On-Screen Display (OSD) Menu Prepare the Remote Control for Use Remote Control Options Add Batteries to the Remote Mount the Remote Control Holster Mount the Remote Control Receiver Preparing the Stylus for Use Adding and Replacing the Stylus Battery Storing the Stylus Replacing the Stylus Tip The Walk-and-Talk Software Driver Windows System Requirements Macintosh System Requirements Driver Installation Operating your Interactive Panel Register Your Walk-and-Talk Interactive panel Cleaning and Maintenance How to Obtain Replacement Parts Troubleshooting Display Timing Technical Support FCC Compliance Warranty Table of Contents 1

4 2

5 OVERVIEW Congratulations on your purchase of a PolyVision Walk-and-Talk Interactive Panel, which provides a sleek and simple solution to interactivity using your computer and a projector. This manual describes how to install and use the Walk-and-Talk Interactive Panel. For information about using the Walk-and-Talk driver on your computer, refer to Driver Installation on page 20. An electronic (PDF) version of the Walk-and-Talk User Guide is installed with the software driver (or available for download at To view the user guide in Windows: Click Start in the lower left corner of your desktop, choose Programs, then PolyVision, and then Walk-and-Talk User Guide. To view the user guide on a Macintosh: Navigate to the /Library/Documentation folder on your start-up disk, and double-click Walk-and-Talk User Guide. Overview 3

6 OPTIONS AND CONSIDERATIONS The Walk-and-Talk Interactive Panel is a remote control-enabled interactive system using your computer, a projector, and any size projection screen. You can point, click, and annotate on anything that you can project. Press Print on the remote control to send a digital snapshot to the default printer connected to your computer. Press Save on the remote control to save the digital snapshot as a file on your computer, just as a digital image from a camera would be. Walk-and-Talk enables you to operate your computer from the interactive panel using the stylus, or to roam freely about the room and operate your computer using the remote control touch pad and buttons. For details about using the remote control buttons, refer to the on-line Walk-and-Talk User Guide. The interactive panel comes with its own 6-foot VGA-in cable and 15-foot USB cable for connection to your computer. It also includes a 12-inch VGA-out cable for quick connection to your projector s video cable. Alternatively, you can connect a projector s video cable directly to the interactive panel. The infrared remote control enables you move about the room and control your computer from anywhere within a 40-foot radius of the remote control receiver. The remote control receiver has a 6-foot USB cable that connects to your computer s second USB port. The receiver requires line-of-sight access to the remote control. You can fasten the receiver to the front of a podium, place it on a desktop, or you can mount it to a wall or ceiling. For large auditoriums, you can add additional remote control receivers or extend the receiver s USB cable so you can position the receiver in an optimum location for added mobility while using the remote control. Refer to Extending Remote Control Reception on page 8. The battery-operated stylus has two functions: it enables you to control your computer cursor so you can operate your computer from the interactive panel, and you can use it to mark-up the projected computer image, adding notes or highlighting information during your presentation. Store the stylus either in the pen holder along side the interactive panel or tuck it into the clip at the back of the panel. Refer to Operating your Interactive Panel on page 23 for additional information. 4 Overview

7 Instant Plug and Play Technology INSTALLING THE INTERACTIVE PANEL WHAT COMES IN THE BOX 3 1 interactive panel 2 holster for remote control with one thumb screw 3 remote control receiver with USB connector and two mounting screws 4 power cable with adapter 5 USB cable with PolyKey 6 remote control (with two AA batteries) 7 two remote control lanyards: one wrist-sized, one neck-sized 8 AAA stylus battery 9 stylus 10 replacement stylus tips 11 quick start installation guide 12 this manual 13 installation CD (for Windows 98 only) 14 Walk-and-Talk Tutorial DVD PolyKey TM TM Walk-and-Talk Interactive Panel Installing the Interactive panel 5

8 CONNECTING CABLES Preparing to Connect Cables Locate and have ready to use: Phillips screwdriver remote control receiver (provided) Assure that your computer has: two USB ports one VGA port Connecting Cables To connect cables: 1 Ensure that your computer is powered off. Plug and Play Technology TM Instant PolyKey 2 Connect the power cable from the interactive panel to a power outlet. 3 Connect the VGA cable from the interactive panel to your computer s VGA output. 4 Connect the USB cable from the interactive panel to the USB port of your computer. 6 Installing the Interactive panel

9 note: NOTE: note: NOTE: The USB cable end that plugs into your computer has two connectors: a PolyKey connector and a regular USB connector. Plug in the regular USB connector to operate the interactive panel. Plug in the PolyKey to install the Walk-and-Talk driver that you need on your computer to operate the Interactive panel. Refer to Driver Installation on page To use the interactive panel with a projector, connect it to the VGA-out 12-inch cable extension (provided) on the interactive panel. Your computer must have two USB ports: one for the remote control receiver and one for the USB connection to the interactive panel. You can use a USB hub if your computer has only one USB port. 6 Connect the remote control receiver (provided) to a USB port on your computer. Refer to Mount the Remote Control Receiver on page 17 for information about mounting the receiver for line-of-sight access to the remote control. Installing the Interactive panel 7

10 Extending Remote Control Reception The remote control receiver requires line-of-sight access to the remote control and includes a 6' USB cable for connection to your computer. The remote control operates within 40' of the receiver. In very large presentational halls and auditoriums, you may need additional remote control receivers and/or USB extensions to provide added mobility while using the remote control. You can obtain additional remote control receivers from PolyVision. Refer to How to Obtain Replacement Parts on page 26. Each receiver must be connected to your computer. If you lack the required number of USB connectors, you can add a USB hub, available at office supply stores. You can also extend the remote control receiver USB cable. Without an active extension, USB cables can be a maximum of 5 meters (15 feet) long. Various active extensions are available that can extend the length of the cable up to 1000 feet. USB extensions are available at electronics and office supply stores. 8 Installing the Interactive panel

11 PREPARING THE INTERACTIVE PANEL FOR USE ADJUSTING THE TILT OF THE PANEL The Walk-and-Talk Interactive Panel adjusts to any position that is comfortable. It can lay flat or tilt up to any position. To tilt the panel: 1 Place the interactive panel on a lectern, podium, or desktop. 2 Lift and hold the release latch on the back of the panel. 3 Raise or lower the panel to the desired tilt. 4 Release the latch. Preparing the Interactive Panel for Use 9

12 THE INTERACTIVE PANEL CONTROL BUTTONS The interactive panel control buttons are located in the upper left corner on the front of the interactive panel. Menu item select auto image adjust power Menu Auto Getting Started with the Interactive Panel To power on the interactive panel: Press the Power button. The LED beside the Power button glows green when power is on and a video signal is present. It glows orange when no video signal is present. When you first connect the interactive panel and a computer, it is a good idea to synchronize the panel with your computer screen s phase, clock, and vertical and horizontal position. To automatically adjust the interactive panel for use with your computer: Press the Auto button. 10 Preparing the Interactive Panel for Use

13 Using the On-Screen Display (OSD) Menu The OSD menu enables you to adjust the interactive panel s LCD screen. To view the OSD menu: Press the Menu button. To close the OSD menu when it appears in the screen: Press the Auto button. To select an OSD menu option: 1 Press the left or right arrow buttons to highlight a menu option. 2 Press the Menu button to confirm your selection. To recall all OSD factory settings: Press the Auto button when the OSD menu is not displayed. These OSD menu options appear when you press the Menu button. Input Selection Menu Channel 1 Channel 1 RGB signal Channel 1 YUV signal Channel 2 Preparing the Interactive Panel for Use 11

14 Input Selection Menu Channel 2 RGB signal Channel 2 YUV signal Channel 3 Channel 4 Channel 5 Bright/contrast Menu Brightness Contrast 12 Preparing the Interactive Panel for Use

15 Color Menu srgb: Recall factory default colors Temperature Shape Menu Auto: Recall factory default clock/phase Clock: Adjust the horizontal size of the display Phase: Adjust the phase of the display H Position: Adjust the horizontal display position Preparing the Interactive Panel for Use 13

16 Shape Menu V Position: Adjust the vertical display position Tool Menu Adjust the OSD menu elapse time and position Recall all factory default settings Recall factory default colors Recall factory clock/phase settings 14 Preparing the Interactive Panel for Use

17 Tool Menu Sharpness: Adjust the sharpness of the display PREPARE THE REMOTE CONTROL FOR USE The Walk-and-Talk Interactive Panel includes a remote control that enables you to roam freely about the room while you operate your computer using the remote control touch pad and buttons. Remote Control Options The remote control functions equally well in various locations. Place the remote control in the holster attached to the side of the panel. The touch pad and buttons are easily accessible from the holster. Carry the remote control with you using the wrist or neck lanyard provided. Place the remote control near you on a desk or table top pointed toward the remote control receiver. Preparing the Interactive Panel for Use 15

18 Add Batteries to the Remote The Walk-and-Talk infrared remote control uses two AA batteries (provided). To add batteries: Press down and pull back to release the battery compartment door. Mount the Remote Control Holster The remote control fits in a holster attached to the left side of the interactive panel. To install the holster: 1 Locate the thumbscrew for the holster bracket. 2 Position the holster on the left edge of the panel, matching the hole in the holster with the hole in the panel. 3 Fasten the holster to the panel, using the thumbscrew provided. 16 Preparing the Interactive Panel for Use

19 Mount the Remote Control Receiver The infrared remote control is battery operated and functions in conjunction with a remote control receiver that connects to your computer s second USB port. Always point the remote control directly at the remote control receiver. Place the remote control receiver in a location where it has direct, line-ofsight exposure to the infrared remote control. Refer to Options and Considerations on page 4. One option is to mount the remote control receiver by attaching the screws provided to any appropriate surface and engaging them in the keyhole slots on the bottom surface of the receiver. For example, you could mount the receiver to a ceiling tile, to a lectern, or to a wall. The remote control receiver USB cable is 6 feet long. Refer to Extending Remote Control Reception on page 8 for information about adding remote control receivers or extending the receiver s USB cable. To mount the remote control receiver: 1 Install the two screws provided. 2 Match the keyhole slots on the back of the remote control receiver to the screws and slide the receiver onto the screws. The receiver can easily be removed and replaced once the screws are in place. Preparing the Interactive Panel for Use 17

20 PREPARING THE STYLUS FOR USE The interactive panel includes a stylus that enables you to operate your computer from the interactive panel s LCD screen. For information about using the stylus, refer to Operating your Interactive Panel on page 23. Adding and Replacing the Stylus Battery The stylus requires one AAA battery (provided). To add or replace the stylus battery: Gently unscrew the end cap. Storing the Stylus The interactive panel provides a convenient stylus holder beside the panel. 18 Preparing the Interactive Panel for Use

21 Replacing the Stylus Tip The tip of the stylus can become worn with use. Two replacement tips are provided. To remove the old stylus tip: 1 Grip the stylus tip with a tweezer. 2 Pull the tip straight out of the stylus. To add a replacement tip: Push the tip straight into the stylus until it snaps into place. Preparing the Interactive Panel for Use 19

22 THE WALK-AND-TALK SOFTWARE DRIVER The Walk-and-Talk Interactive Panel operates with your computer and a projector to provide a fully interactive system. The Walk-and-Talk driver is required on your computer. WINDOWS SYSTEM REQUIREMENTS To use the Walk-and-Talk driver with an interactive panel, your Windowsbased computer must have: Windows 98, ME, 2000, XP, or Tablet XP VGA HD-15 video port Two USB ports MACINTOSH SYSTEM REQUIREMENTS To use the Walk-and-Talk driver with an interactive panel, your Macintosh computer must have: PowerPC G3 or higher Mac OS 10.1 or higher DVI to VGA connector Two USB ports DRIVER INSTALLATION The Walk-and-Talk driver is always close at hand. You need no installation disk or CD-ROM (unless you are using Windows 98: a CD-ROM is included for Windows 98 users). Installation takes place when you connect the PolyKey (on the Walk-and-Talk USB cable) to your computer s USB port. To install the Walk-and-Talk driver on your computer using Mac OS 10.1 or higher, Windows ME, 2000, XP, or Tablet XP: 1 Locate the Walk-and-Talk USB cable. 20 The Walk-and-Talk Software Driver

23 2 Connect the PolyKey on the USB cable to your computer s USB port. Instant Plug and Play Technology PolyKey TM 3 Windows ME and 2000: installation begins automatically. Windows XP and Tablet XP: double-click My Computer on your desktop and double-click the removable disk drive named PolyKey. Software installation begins. Macintosh: double-click the PolyKey icon on your desktop, doubleclick the Macintosh folder, and double-click Walk-and-Talk Installer. Installation begins. 4 Windows only: check the box beside IP17 when prompted to select your device. 5 Follow the prompts you see on the screen to complete the installation. On a Macintosh, you are prompted to reboot. To install the Walk-and-Talk driver on a computer using Windows 98: 1 Turn on your computer and wait for Windows to start. For best results, make sure no applications are running. 2 Place the Walk-and-Talk software CD in your CD-ROM drive. The setup program starts. If the setup program does not start, open Windows Explorer and double-click Setup.exe on the CD. 3 Follow the prompts to install the driver. 4 Restart the computer. The Walk-and-Talk Software Driver 21

24 When installation is complete, a message appears on your computer screen and the Walk-and-Talk icon appears in your system tray (Windows) or system menu (Macintosh). system menu (Macintosh) Walk-and-Talk icon system tray (Windows) To start using your interactive panel: 1 In Windows: disconnect the PolyKey. On a Macintosh: drag the PolyKey icon to the Trash or choose Eject from the File menu, then disconnect the PolyKey. 2 Connect the USB cable to your computer s USB port. The Walk-and-Talk driver runs unobtrusively in the background whenever your computer is on and connected to a Walk-and-Talk-enabled product via the USB cable. Instant Plug and Play Technology PolyKey TM 22 The Walk-and-Talk Software Driver

25 OPERATING YOUR INTERACTIVE PANEL To get started using your Walk-and-Talk Interactive Panel: Power on your computer and the Walk-and-Talk Interactive Panel. You can operate your computer from the interactive panel using the stylus, or you can roam freely about the room and operate your computer using the remote control touch pad and buttons. Refer to the Walk-and-Talk User Guide for complete information about using the remote control. The stylus that you use with the interactive panel serves as a mouse to control your computer cursor. You can drag and tap the stylus on the surface of the panel or use the stylus from a distance of about one inch from the panel. To control your computer using the stylus: To click, tap the panel once. To double-click, tap the panel twice rapidly or hold the stylus above the panel and press the stylus button closest to the tip. Operating your Interactive Panel 23

26 For a right-click (Windows) or control-click (Macintosh), hold the stylus to the panel for one second, or hold the stylus above the panel and press the right-click button on the stylus. right click left double-click left click The stylus can also write over the projected computer image, enabling you to add notes and highlight the projected computer image during your presentation. Refer to the on-line Walk-and-Talk User Guide for complete information about using the stylus for mark-ups. 24 Operating your Interactive Panel

27 REGISTER YOUR WALK-AND-TALK INTERACTIVE PANEL By registering your product, you will receive enhanced customer service with information on software upgrades. To register Walk-and-Talk: Register on-line at: Register Your Walk-and-Talk Interactive panel 25

28 CLEANING AND MAINTENANCE note: NOTE: We recommend an initial cleaning of the panel to remove any residue left behind during manufacture. 1 For the initial cleaning, wipe your board with a clean cloth moistened with clear water. 2 Wipe dry with a clean cloth. Do not let water seep into the sensitive interactive panel electronics. Your warranty does not cover damage caused by liquids. HOW TO OBTAIN REPLACEMENT PARTS Replacement parts are available directly from PolyVision. Call POLY (7659) in the USA, from elsewhere in North America, or +32 (0) in Europe. Or, send to info@polyvision.com. 26 Cleaning and Maintenance

29 TROUBLESHOOTING Issue The picture does not appear No power light Resolution Check to make sure that the VGA cables are firmly attached. Check that the Power is ON at your computer. Check that the brightness or contrast is at an appropriate level, not at the minimum. Check that your external computer video is enabled. Press Fn-F5 or Fn-F8 on some computers to toggle the display of video. Check that the power adapter is plugged in. Check that the power outlet is functional. The screen is not synchronized The screen is not centered The display is shaky or wavy Press the Auto button on the interactive panel. Check to make sure that the VGA cables are firmly attached. Make sure that the display timing of your computer is within the specifications listed in Display Timing on page 28. Press the Menu button at the top right of the panel and choose the H-position and V-position menu options. Refer to Using the On-Screen Display (OSD) Menu on page 11. Remove objects which emit a magnetic field, such as a monitor or transmitter. Make sure that the display timing of your computer is within the specifications listed in Display Timing on page 28. Troubleshooting 27

30 Issue The stylus does not function The stylus does not control the cursor correctly Resolution If the Walk-and-Talk icon appears in your computer system tray (Windows) or system menu (Macintosh), replace the stylus battery. Refer to Preparing the Stylus for Use on page 18. If the Walk-and-Talk icon is absent but the driver was installed, disconnect and reconnect the USB cable, or restart your computer. If these steps fail, remove and re-install the Walk-and-Talk driver, or remove possible software conflict from your computer. Disconnect and reconnect the USB cable or restart your computer. DISPLAY TIMING The interactive panel LCD display is compatible with a wide variety of computers. The native resolution is 1280x1024. The table below describes the display frequency and resolution of compatible modes. Model Resolution H-Freq (khz) V-Freq (Hz) VGA 60Hz VGA 72Hz VGA 75Hz SVGA 800x600@ 60Hz SVGA 72Hz SVGA 75Hz XGA 60Hz XGA 72Hz XGA 75Hz SXGA 60 Hz SXGA 75 Hz Troubleshooting

31 TECHNICAL SUPPORT If reviewing the above sections fails to resolve your hardware or software problem, contact PolyVision USA Technical Support: Phone: POLY (7659), Technical support representatives are available Monday through Friday from 8 AM Eastern time to 8 PM Eastern time. Fax: support@polyvision.com Internet: Or, outside the USA, contact PolyVision Europe/Asia Technical Support: Phone: +32 (0) Fax: +32 (0) business.center@polyvision.com Internet: FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Troubleshooting 29

32 WARRANTY PolyVision Corporation warrants to the original consumer or other end-user purchaser that this product is free from defects in material and workmanship for a period of two years from the date of purchase. During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar model) at PolyVision s option, without charge for either parts or repair labor. Shipping costs will apply. Please keep your original sales receipt or delivery invoice for proof of purchase. Without proof of the purchase date, your warranty will be defined as beginning on the date of manufacture, which is recorded by serial number at the factory. This warranty applies only to the first end-user purchaser and only when the product is used in a country for which it is labeled for sale. Some factoryreconditioned parts may be used in the assembly of this panel. WHAT IS NOT COVERED 1 Any product that is sold or used outside of North America and Europe unless the product was specifically labeled for sale in that country. 2 Any product on which the serial number has been defaced, modified, or removed. 3 Damage, deterioration, or malfunction resulting from, but not limited to: Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. Use of unintended writing implements such as (but not limited to) ball point pens, pencils, fountain pens, or non-dry-erase markers. Use of non-approved cleaning materials or solvents. Repair or attempted repair by anyone not authorized by PolyVision. Any damage incurred in shipping. Removal or installation of the product. Any other cause that does not relate to a product defect. 4 Cartons, carrying cases, pens, external cabinets, easels, or any accessories used in connection with the product. 5 Removal and/or installation charges. 6 Shipping charges to and from our factory or authorized repair depot. HOW TO GET WARRANTY SERVICE If you experience a problem with this product, contact your local dealer or PolyVision Product Support ( POLY or in the USA, or +32 (0) in Europe) to resolve the problem. If the product is diagnosed as being defective, return the product to the original place of purchase. If you are directed to return the product directly to PolyVision, you must obtain a Return Materials Authorization 30 Warranty

33 (RMA) number from PolyVision. All products returned to PolyVision must have an RMA number assigned, regardless of reason for return. The RMA number must be clearly marked on the outside of the shipping carton; any unit without an RMA number will be returned to the sender. LIMITATION OF DAMAGES AND IMPLIED WARRANTIES POLYVISION WARRANTS THAT THE PRODUCT WILL OPERATE SUBSTANTIALLY IN CONFORMITY TO THE POLYVISION DOCUMENTATION AND PUBLISHED SPECIFICATIONS FOR A PERIOD OF TWO YEARS AFTER CONSUMER PURCHASE, PROVIDED IT IS USED IN ACCORDANCE WITH POLYVISION S USER INSTRUCTIONS. POLYVISION S SOLE AND EXCLUSIVE LIABILITY, AND YOUR EXCLUSIVE REMEDY, FOR ANY BREACH OF THIS WARRANTY IS THAT, IF THE BREACH IS REPORTED TO POLYVISION IN WRITING WITHIN THE WARRANTY PERIOD, POLYVISION WILL CORRECT THE NONCONFORMITY, EITHER BY CORRECTING THE PRODUCT OR (WHERE APPROPRIATE) DOCUMENTATION; REPLACING THE PRODUCT; OR, WHERE POLYVISION DETERMINES THAT CORRECTION OR REPLACEMENT IS NOT FEASIBLE, REFUNDING THE FEE ACTUALLY PAID FOR THE PRODUCT. NO OTHER REMEDY SHALL BE AVAILABLE TO YOU. EXCEPT AS EXPRESSLY SET FORTH HEREIN, POLYVISION MAKES NO WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. POLYVISION DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. POLYVISION SHALL HAVE NO LIABILITY BEYOND THE OBLIGATIONS SET FORTH ABOVE. IN NO EVENT SHALL POLYVISION BE LIABLE FOR ANY INDIRECT DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL, OR OTHERWISE (AND EXPRESSLY INCLUDING LOST PROFITS AND LOSS OF DATA) OR FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THIS PRODUCT UNDER THIS OR RELATED AGREEMENTS, WHICH DAMAGES ARISE OUT OF THE USE OF THE HARDWARE, IRRESPECTIVE OF WHETHER POLYVISION SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES AND IRRESPECTIVE OF THE CAUSE OF DAMAGE, INCLUDING NEGLIGENCE. SOME STATES OR COUNTRIES RESTRICT THE RIGHT TO EXCLUDE CERTAIN WARRANTIES, THEREFORE, THE ABOVE EXCLUSIONS MAY NOT APPLY TO YOU. HOW STATE LAW RELATES TO THE WARRANTY In the USA, this warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. PolyVision Corporation products are warranted in accordance with the terms of the applicable PolyVision Corporation limited warranty. Product performance is affected by system configuration. Software, the application, customer data, and operator control of products are considered to be compatible with many systems. The specific suitability of a product for a specific purpose or application must be determined by the customer and is not warranted by PolyVision Corporation. Warranty 31

34 Warranty 32

35 Index A Auto Image Adjust button 10 C cleaning the panel 26 click 23 computer interactivity using stylus or remote control 4 control buttons 10 control-click 24 D display frequency and resolution 28 double-click 23 F FCC compliance 29 G get started installing software 20 H holster 16 using 15 I installing software 20 interactive panel control buttons 10 L lanyard for remote control 15 M menu for on-screen display 11 O operating your computer 23 OSD menu 11 P PolyKey for software installation 20 power on 10 R registering Walk-and-Talk 25 remote control battery replacement 16 carrying with lanyards 15 holster installation 16 maximum distance 4 options 15 table-top use 15 ways to use 15 remote control receiver connecting 7 exendingusb cable 8 mounting 17 overview 4 replacement parts 26 right-click 24 S software installation 20 installation for Windows requirements 20 stylus 18, 23 battery replacement 18 mark-ups 24 overview 4 positions for storage 18 system requirements 20 T Technical Support 29 tilting the panel up or down 9 troubleshooting 27 U USB cable PolyKey 20 W Walk-and-Talk on-line user guide 3 software driver 20 33

36 34