AB-910W. A-Bus Two Zone Audio Kit w/bluetooth & 2 pair In-Wall Speakers. Intelligent Entertainment Infrastructure Security Solutions CHANNEL VISION

Size: px

Start display at page:

Download "AB-910W. A-Bus Two Zone Audio Kit w/bluetooth & 2 pair In-Wall Speakers. Intelligent Entertainment Infrastructure Security Solutions CHANNEL VISION"

Derek Shields
5 years ago
Views:

1 IR Out Local In Sys Priority Loc 24VDC Channel Vision AB-910W A-Bus Two Zone Audio Kit w/bluetooth & 2 pair In-Wall Speakers R Intelligent Entertainment Infrastructure Security Solutions

2 Product Introduction Simplify your installation with this two zone bluetooth audio package. This audio package allows you to customize individual rooms to give anyone in condos, hotels, dorm rooms, and bedrooms control over their own smartphone or other streaming music. The AB-910W Kit includes the (1), (2) AB-135W, (1) AB-303 (2) pair IW603 speakers, and an AB-T2410 power supply. 1. Read these instructions. 2. Keep these instructions for future reference. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this device near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. This apparatus must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Unplug this apparatus during lightning storms or when unused for long periods of time CAUTION RISK OF ELECTRIC SHOCK! DO NOT OPEN Warning: To reduce the risk of electric shock, do not remove the cover (or back), no user serviceable parts inside, refer servicing to qualified service personnel. 2

3 Model AB-135W The AB-135 is an amplified keypad for Channel Vision s single-source CAT5 audio systems. It provides convenient volume control capabilities while its elegant decorator styling blends seamlessly with other wall switch devices. Features: Compatible with Channel Vision single source CAT5 audio systems Easy to use volume control Volume Controls... Increase or decrease volume level. /Source Button... Keypad On/Off control and source selection control when in multi-mode. Green LEDs...These LED s illuminate green to indicate volume level Compatibility The AB-1 35 adheres to the same protocols as Channel Vision s other CAT5 audio hubs to ensure maximum compatibility. Single-source CAT5 audio products from other manufacturers may not (and typically will not) use the same control codes for the AB-135 keypad. How it Works The AB-1 35 can be used to control a single source with a CAT5 audio hub. The unit provides basic controls: volume up, volume down, and power on/off. Basic Operation Using the AB-135 Amplified keypad... The (power) button located at the lower left of the keypad is used to turn the unit on or off. Press and hold the power button to turn the keypad off. After volume is changed, the LEDs will stay lit for 5 seconds, showing the current volume level. Volume adjustments can be made using the up/down buttons to the right hand side of the keypad. 3

4 Model AB-303 The AB-303 A-BUS Bluetooth local input module provides a local wireless input connection for the purpose of streaming audio from sources such as smart-phones, tablets and computers, etc with Bluetooth capability to individual A-BUS equipped rooms. When the AB-303 is paired, it will automatically switch the music source from the main audio source to the local Bluetooth source. This local connection will remain until pairing is disconnected, or the Bluetooth device is out of range. If pairing remains selected on the Bluetooth device, when it comes back into range, the connection will automatically reconnect and play audio in the zone. Features: h Adds Bluetooth streaming capability to existing or new A-BUS systems h Functions as a main or local source Operation: Plug the AB-303 output (do no use input) into the System Input on the back of the AB To pair to the AB-303, consult instructions on pairing supplied with your Bluetooth device. The Bluetooth LIM identification code will have the prefix AB in front of the individual code number. When pairing occurs, a blue LED will light up on the front plate. For systems with multiple AB-303s, it is recommended the codes be changed to easily identify each room before completing installation. Operating Range: Bluetooth devices are intended to provide wireless communication between enabled devices within a room. In ideal conditions, range can be up to 50 This distance can be reduced significantly by transmission interference from other communication devices, electrical wiring and room construction materials, such as brick walls and concrete floors. When the AB-303 is operating near maximum range, the signal may intermittently drop in and out, as signal strength varies. Bluetooth Source Volume Level Compatibility: The audio output level from Bluetooth enabled devices can vary from brand to brand. Though the AB-303 has been adjusted to be equal to the output of most Bluetooth devices, in some cases the level may be different. Most devices have their own adjustable volume level, and it is recommended that this be used to adjust the output level to match the main audio source s volume level. Room Identification: Pairing each AB-303 requires the identification of an individual code number beginning with the prefix AB (ABxxx). This code number can be replaced with an individual room name identification such as Bedroom 1, Study, Patio, etc. prior to installation. To download the renaming software visit Once downloaded and installed, connect the AB-303 via the mini USB socket located at the side of the unit to your PC and start the program, follow the on screen prompts to rename the device. 4

5 Model The functions as the heart of your A-BUS system. It is a 1x2 distribution module that deliver power and audio signals to 2 amplified keypads (model AB-135). Features: Fits into a standard 2-gang low voltage ring (not included) Integrated single source audio input A-Bus input from remote room IR emitter output (not used if using an AB-135) IR Out The priority switch determines which input will be heard (either A-BUS or Local) when audio is sensed from both. Sys Priority Loc 24VDC Local In Local Input 24VDC power supply connection (included). Front panel connections Rear panel connections Zone outputs for keypad connections. A-BUS Input from model AB-203, AB-303, or Expansion output. A-BUS Input Zone 1 Zone 2 1x2 A-BUS Distribution Module by Channel Vision Expansion Out International Patent Pending Leisure Tech Electronics Ltd Australia MADE IN CHINA Expansion connector is used to hook up additional s. 5

6 International Patent Pending Leisure Tech Electronics Ltd Australia MADE IN CHINA System Diagram Expansion Output: Use this to expand to an additional. This connector only provides audio signals to an additional. It cannot be used to directly connect a 3rd AB-135 to the system. Cat-5 cables: Use RJ-45 connectors that are wired for the TIA568A standard. (Using the TIA568B wiring configuration will work, but the left and right audio information will be reversed). Volume indicators: The LEDs indicate the volume level. If the Status is <off>, the LEDs will be dark. Pressing the UP/DOWN keys will light the LEDs for a short period to show the stored volume level. Front IR Out Receiver Local In Sys Priority Loc 24VDC Power supply (AB-T2410) AB-135 AB-303 Rear 2 AB-135 A-BUS Input Zone 1 Zone 2 1x4 A-BUS Distribution Module by Channel Vision Expansion Out 1 Room 1 Use speaker wire rated for use in walls. AWG 18 or larger is recommended. Be sure to wire speakers in phase. + terminal on the AB-135 to the + or red terminal on each speaker. Source Source 6 3 Room 2

7 Troubleshooting Problem: Hum in System Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away. Try lifting the ground with a ground lifting plug. Possible Cause: The different components in the system are connected to different electrical grounds. This forces electrical currents to find alternate paths to ground causing an audible 6 0Hz hum. Solution: Plug products into an electrical circuit with a common ground. Problem: RCA Audio input is not working. Troubleshooting: Verify source audio is playing, or try another audio source Check speaker wires to verify nothing is backwards or crossed. Possible Cause: There is no signal (or very weak signal) coming from the source, or source is not compatible with Solution: Make sure the source audio is playing. Try a different source. Problem: CAT5 audio input (AB-303 or other device) is not working. Troubleshooting: Verify you have plugged the CAT5 output on the AB-303 or other A-Bus input module into the input on the back of the. Verify you have plugged the zone 1 or zone 2 output of the into the input on the back of the AB-135. Possible Cause: AB-303 or other A-Bus input module is not connected properly, wire crimped improperly or plugged into the wrong terminal. Solution: Verify wiring, verify RJ-45 crimps Problem: Not linking with Bluetooth device or Linking with no audio is present. Troubleshooting: 1. Restart Bluetooth source device 2. Check Source device is connected to Wifi 3. Check the music source is active before pairing 4. The blue LED indicates when devices are paired 5. Try a different A-BUS source. 6. Make sure Bluetooth device is in play mode Problem: Audio quality issues Troubleshooting: Verify you have connected the CAT5 cable correctly. Follow the TIA-568A standard at both ends. Mis-wiring can cause distorted sound, prevent the system from functioning, or possibly cause damage to the components in the system. Verify you have connected the speakers in phase. Follow the label on the product. Out of phase speakers can rob the system of its bass, especially when driving dual-voice-coil speakers. If no audio is heard, check to make sure that the audio source is playing, then press the power button on the AB-135 to make sure it is turned on. Pin-out Top view: Green/White - Left Channel Audio Ground Green - Left Channel Audio Orange/White - Right Channel Audio Ground Blue - IR Signal Blue/White - Status Orange- Right Channel Audio Brown/White 24vDC Ground Brown 24vDC 7

8 One Year Limited Warranty Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, acts of God, or alteration of the equipment. This warranty is extended only to the original purchaser when purchased through an authorized reseller. A purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided. Mail in service can be obtained during the warranty period by calling (714) A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton. This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center. Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical environment applications. Channel Vision customers using or selling Channel Vision products for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale. AB-135, & AB-303 Specifications: (typical at 77º) Operating Voltage: 24VDC 1 Amps (one keypad) Cable requirements: CAT5 or CAT6 Speaker impedance: 6-8 ohm (max two speakers per AB-135) IR repeating: 30-60kHz IR sensor range: Operating Temperature: -10ºC to +50ºC Line Level input (AB-203): Max 1VRMS IC603 Specifications: (typical at 77º) Frequency range: 60Hz - 20kHz Crossover: Electronic Sensitivity: 89dB Power Handling: 120 Watts peak Drivers: ½ Compliance Polymer Tweeter Black PP Cone with Rubber Edge (woofer) Magnet: 10-ounce magnet Impedance: 8 ohms Finish: ABS plastic Dimensions: 12.1 H x 8.59 W x 3.7 D (Depth from surface of wall board) Hole size: x 7.32 Tested To Comply With FCC Standards *Specifications subject to change without notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. A-BUS is a registered trademark of LeisureTech Electronics Pty Ltd. This product may be covered by one of the following patents: US patent no. 7,181,023, 6,389,139 EP , AU , NZ , Mexico Z41196, Canada CA Intelligent Entertainment Infrastructure Security Solutions 234 Fischer Avenue, Costa Mesa, California USA (714) (800) (714) fax techsupport@channelvision.com w w w. c h a n n e l v i s i o n. c o m rev A

A0319. Bluetooth Wall-Dock for Distributed Audio. Intelligent Entertainment Infrastructure Security Solutions

A0319. Bluetooth Wall-Dock for Distributed Audio. Intelligent Entertainment Infrastructure Security Solutions A0319 Bluetooth Wall-Dock for Distributed Audio Intelligent Entertainment Infrastructure Security Solutions The A0319 is an on-wall bluetooth docking station that will charge an ipod, iphone or itouch