Wintec Slim SATA Drive JM608 Series

Transcription

1 Wintec Slim SATA Drive JM608 Series W2ESxxxG1TA-J71xx INORMATION IN THIS DOCUMENT IS PROIDED IN RELATION TO WINTEC INDUSTRIES PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EPRESS OR IMPLIED. ALL INORMATION IN THIS DOCUMENT IS PROIDED ON AN AS-IS BASIS WITHOUT GUARANTEE OR WARRANTY O ANY KIND. Please contact your nearest Wintec representative for the latest updates or additional product information. ersion 1.0 Page 1

2 Product Introduction Wintec Slim SATA Drive JM608 Series W2ESxxxG1TA-J71xx The Wintec Industries W2ESxxxG1TA(I)-J71xx series of ROHS Compliant Slim SATA Drives are constructed with MLC NAND-type flash memory devices paired to JMicron 608 SATA III NAND lash controller for virtual-to- physical address mapping and other sophisticated flash management functions. The Wintec lash Solid State Disk (SSD) provides major advantages over the traditional magnetic hard disk drive (HDD). aster access time and transfer rate, silent operation and low power consumption, better shock and vibration resistance, and lower total cost of ownership make the Wintec SSDs an attractive choice as the next generation mass storage device. The Wintec JM608 series Slim SATA provides high-speed data transfer and reliability utilizing MLC NAND-flash in storage capacities ranging up to 128GB, in JEDEC MO-297A form factor. Its robust design enables the SSD to achieve outstanding reliability and performance. The JM608 controller implements bad block management and dynamic/static wear-leveling techniques to ensure that the NAND flash memory is not worn out prematurely. The controller utilizes up to 40 bits/1k byte sector BCH ECC algorithms for error correction. The drive supports basic SMART features to monitor the drive status. The Wintec JM608 series Slim SATA drives are ideal for portable and desktop computers, point of sale (POS), handheld device, gaming machine, network equipment, notebook, thin-client and set-top boxes (STB). General eatures Density up to 128GB SATA-III interface and backwards compatible High-Performance MLC NAND lash memory Reliability Enhanced endurance by dynamic/static wear Leveling Bad Block Management ECC Engine: Utilizes 8/16/24/40 bit correctable per 1KB BCH ECC Data Integrity under power cycling Support Shift read feature of NAND flash when ECC fail MTT: 1,000,000 operating hours I-Temp Available Performance High Performance 300MB/s Seq. Read (SATA-III) High Performance 200MB/s Seq. Write (SATA-III) Random Read: 15,000 IOPS at 4KB transfer (SATA- III) Compatibility Serial ATA Revision 3.1 Compliant ATA/ATAPI-8 Compliant Supports S.M.A.R.T RoHS compliant NOTE: 1. See Section 5.0 for Configuration & Ordering Guide ersion 1.0 Page 2

3 Revision History Revision Month Year History 0.99 March 2014 Preliminary Release 1.0 June 2014 Added 50GB capacity ersion 1.0 Page 3

4 Table of Contents 1.0 General Product Specifications Block Diagram Architecture Electrical Specifications General SATA P in Assignment and Description Software Interface ATA Command Set ATA Command Description: IDENTIY DEICE (ECh) ATA Command Description: SET EATURES (Eh) SMART Command Support Physical Dimensions Product Guide & Ordering Information 17 ersion 1.0 Page 4

5 1.0 General Product Specifications or all the following specifications, values are defined at ambient temperature unless otherwise stated. Table 1: User Capacity Specifications Model Number¹ (typ) 2,3 NAND lash Type Total Capacity User Capacity Over-provision W2ES004G1TA(I)-J71xx-yyy.zz MLC 4GB 3.5G 7% W2ES008G1TA(I)-J71xx-yyy.zz MLC 8GB 7.5G 7% W2ES016G1TA(I)-J71xx-yyy.zz MLC 16GB 15GB 7% W2ES032G1TA(I)-J71xx-yyy.zz MLC 32GB 30GB 7% W2ES050G1TA(I)-J71xx-yyy.zz MLC 64GB 50GB 28% W2ES064G1TA(I)-J71xx-yyy.zz W2ES128G1TA(I)-J71xx-yyy.zz MLC MLC 64GB 128GB 60GB 120GB 7% 7% Note: 1. See Section 5.0 for Configuration & Ordering Guide 2. 1GB = 1,000,000,000 Bytes 3. Capacity available to end-user is less than Total Capacity due to flash controller overhead, and may vary with flash configuration. Table 2: Typical Performance Specifications Parameter Typical Performance 4 Sustained Sequential Read up to 300MB/sec Sustained Sequential Write up to 200MB/sec Sustained IOPS Random Read up to 15,000 IOPS Note: 4. Bandwidth measured on high-performance desktop system. Note that performance may also vary depending on host system, drive capacity, and drive configuration. Measured at QD=32. Table 3: lash Endurance Parameter Program/Erase Cycles Data Retention MTT Table 4: SSD Data Reliability Parameter Non-Recoverable Errors Raw ECC Correctability Spec Up to 3,000 cycles 5 Years (Min.) 1,000,000 Hours Spec < 1 in Bytes Read Up to 40 bits / 1K Bytes data Table 5: Environmental Specifications Parameter Operating Non-Operating Commercial Temp. 0 C to 70 C -55 C to 95 C Temperature Industrial Temp. -40 C to 85 C -55 C to 95 C Humidity (Non-Condensing) 5% to 95% 5% to 95% ibration 20 G RMS N/A Shock (Operating) 1,500 G (Max.) Noise 0 db 0 db ersion 1.0 Page 5

6 1.1 Block Diagram SATA Controller lash Controller 1 & ECC Engine Channel 1 MLC NAND LASH SATA III I/ SATA 6G PHY BUS CPU lash Controller 4 & ECC Engine Channel 2 Channel 3 Channel 4 MLC NAND LASH MLC NAND LASH MLC NAND LASH igure 1: Block Diagram 1.2 Architecture The Wintec J7 series SSD utilizes a single flash controller chip with 4 parallel channels of flash memory interface. The flash controller also simultaneously manages the file read and write interface with the host system via a single SATA-III interface. By utilizing 4 parallel channels of MLC flash memory, the Slim SATA SSD can provide both high performance and reliability, while maintaining a minimal unit cost. ersion 1.0 Page 6

7 2.0 Electrical Specification 2.1 General Table 6: Absolute Maximum Ratings Symbol Parameter Min Max Units cc cc With Respect to GND Table 7: Typical Operating Conditions (CC=3.3 10%) Symbol Parameter Min Typical Max Units cc cc With Respect to GND Operating Temperature 0 70 C T A (Commercial Temp) Industrial Temp C H Humidity 5 95 % Table 8: Power Consumption Symbol Parameter alue Units P i Idle Power consumption 0.35 Watts P T Typical operating power consumption 0.70 Watts P max Maximum operating power consumption 1.25 Watts 2.2 SATA Pin Assignment and Description The SATA connectors are compliant with standard SATA power specifications. As is standard, power may be supplied to all of th e power pins. However, only the 5 power pins are utilized to provide power to the SSD. Therefore, where non -standard power supplies and connections are utilized, the power supply does not need to supply the SSD with power to the 3.3 or 12 power pins. Table 9: SATA connector specification compliant No. Plug Connector Pin Definition Signal Power S1 GND Ground S2 A+ Differential signal A S3 A- S4 GND Ground S5 B- Differential signal B S6 B+ S7 GND Ground Key and spacing separate signal and power segments P power (Not Used) P power (Not Used) P power, pre-charge (Not Used) P4 GND Ground P5 GND Ground P6 GND Ground P7 5 5 power, pre-charge P8 5 5 power P9 5 5 power P10 GND Ground P11 DAS/DSS Device Present P12 GND Ground P power, pre-charge (Not Used) P power (Not Used) P power (Not Used) ersion 1.0 Page 7

8 3.0 Software Interface 3.1 ATA Command Set All mandatory, and many optional commands and features are supported. The following tables summarize the ATA feature set and commands. Table 10: ATA Command Parameters Used eature Set Code SC SN CY DR HD T CHECK POWER MODE E5h O EECUTE DIAGNOSTICS 90h O LUSH CACHE E7h O IDENTIY DEICE ECh O IDLE E3h O O IDLE IMMEDIATE E1h O INITIALIZE DEICE PARAMETERS 91h O O O READ DMA C8h O O O O O READ DMA ET 25h O O O O O READ PDMA QUEUED 60h O O O O O READ LOG DMA ET 47h O O O O O READ LOG ET 2h O O O O O READ MULTIPLE C4h O O O O O READ SECTOR(S) 20h or 21h O O O O O READ ERIY SECTOR(S) 40h or 41h O O O O O RECALIBRATE 10h O SECURITY DISABLE PASSWORD 6h O SECURITY ERASE PREPARE 3h O SECURITY ERASE UNIT 4h O SECURITY REEZE LOCK 5h O SECURITY SET PASSWORD 1h O SECURITY UNLOCK 2h O SEEK 7xh O O O SET EATURES Eh O O O SET MULTIPLE MODE C6h O O SLEEP E6h O SMART B0h O O O STANDBY E2h O STANDBY IMMEDIATE E0h O WRITE DMA CAh O O O O O WRITE DMA ET 35h O O O O O WRITE PDMA QUEUED 61h O O O O O WRITE LOG DMA ET 57h O O O O O WRITE LOG ET 3h O O O O O WRITE MULTIPLE C5h O O O O O WRITE SECTOR(S) 30h or 31h O O O O O ersion 1.0 Page 8

9 Note: O = alid, = Don t care SC = Sector Count Register SN = Sector Number Register CY = Cylinder Low/High Register DR = Device Select Bit (Device/Head Register Bit 4) HD = Head Select bit (Device/Head Register Bit 3-0) T = eatures Register 3.2 ATA Command Description: IDENTIY DEICE (ECh) This commands read out of 512Bytes of drive parameter information. Parameter Information consists of the arrangement and value as shown in the following table. This command enables the host to receive the Identify Drive Information from the device. Table 11: IDENTIY Device (ECh) information default value Word alue / Description h General configuration bit-significant information 15 0 = ATA device 14-8 Retired 7 1 = removable device 6 Obsolete 5-3 Retired 2 Reserved 1 Retired 0 Reserved 1 h Number of logical cylinders 2 C837h Specific configuration 3 00h Number of logical heads 4-5 h Retired 6 h Number of logical sector per logical track 7-8 h Reserved for assignment by the Compactlash_Association 9 000Eh Retired h Obsolete h Retired h Obsolete h irmware revision (8 ASCII characters) h Model number (40 ASCII characters) h h Reserved h h h = Reserved 01h = Maximum number of 1 sectors on READ/WRITE MULTIPLE commands Capabilities Reserved for the IDENTIY DEICE command 13 1= Standby timer values as specified in this standard are supported 0= Standby timer values shall be managed by the device 12 Reserved for the IDENIY PACKET DEICE command 11 1 = IORDY supported 0 = IORDY may be supported 10 1 = IORDY may be disabled 9 1 = LBA supported 8 1 = DMA supported 7-0 Retired ersion 1.0 Page 9

10 Word alue / Description h h Obsolete h h Obsolete h h Capabilities 15 Shall be cleared to zero 14 Shall be set to one 13-2 Reserved 1 Obsolete 0 Shall be set to one to indicate a device specific Standby timer value minimum Capabilities 15-3 Reserved 2 1 = the fields reported in word 88 are valid 0 = the fields reported in word 88 are not valid 1 1 = the fields reported in words 70:64 are valid 0 = the fields reported in words 70:64 are not valid 0 1 = the fields reported in words 58:54 are valid 0 = the fields reported in words 58:54 are not valid 15-9 Reserved 8 1 = Multiple sector setting is valid 7-0 xxh = Setting for number of sectors that shall be transferred per interrupt on R/W Multiple command h Total number of user addressable sectors h Obsolete h Reserved 10 1 = Multiword DMA mode 2 is selected 0 = Multiword DMA mode 2 is not selected 9 1 = Multiword DMA mode 1 is selected 0 = Multiword DMA mode 1 is not selected 8 1 = Multiword DMA mode 0 is selected 0 = Multiword DMA mode 0 is not selected 7-3 Reserved 2 1 = Multiword DMA mode 2 and below are supported 1 1 = Multiword DMA mode 1 and below are supported 0 1 = Multiword DMA mode 0 is supported 15-8 Reserved 7-0 Advanced PIO modes supported h Minimum Multiword DMA transfer cycle time per word h Manufacturer s recommended Multiword DMA transfer cycle time h Minimum PIO transfer cycle time without flow control h Minimum PIO transfer cycle time with IORDY flow control h Reserved (for future command overlap and queuing) Queue depth h 15-5 Reserved 4-0 Maximum queue depth - 1 Serial ATA Capabilities Reserved for Serial ATA 12 1 = Supports NCQ priority information 11 1 = Supports Unload while NCQ commands are outstanding 10 1 = Supports the SATA Phy Event Counters log 9 1 = Supports receipt of host initiated power management requests 76 h 8 1 = Supports the NCQ feature set 7-4 Reserved for Serial ATA 3 1 = Supports SATA Gen3 Signaling Speed (6.0Gb/s) 2 1 = Supports SATA Gen2 Signaling Speed (3.0Gb/s) 1 1 = Supports SATA Gen1 Signaling Speed (1.5Gb/s) 0 Shall be cleared to zero ersion 1.0 Page 10

11 Word alue / Description 77 Reserved 78 h 79 h 80 01Eh h Minor version number h Serial ATA features supported 15-7 Reserved for Serial ATA 6 1 = Device supports Software Settings Preservation 5 Reserved for Serial ATA 4 1 = Device supports in-order data delivery 3 1 = Device supports initiating power management 2 1 = Device supports DMA Setup auto-activation 1 1 = Device supports non-zero buffer offsets 0 Shall be cleared to zero Serial ATA features enabled 15:7 Reserved for Serial ATA 6 1 = Software Settings Preservation enabled 5 Reserved for Serial ATA 4 1 = In-order data delivery enabled 3 1 = Device initiated power management enabled 2 1 = DMA Setup auto-activation enabled 1 1 = Non-zero buffer offsets enabled 0 Shall be cleared to zero Major version number 0000h or h = device does not report version 15 Reserved 14 Reserved for ATA/ATAPI Reserved for ATA/ATAPI Reserved for ATA/ATAPI Reserved for ATA/ATAPI Reserved for ATA/ATAPI-10 9 Reserved for ATA/ATAPI-9 8 Reserved for ATA/ATAPI = supports ATA/ATAPI = supports ATA/ATAPI = supports ATA/ATAPI = supports ATA/ATAPI-4 3 Obsolete 2 Obsolete 1 Obsolete 0 Reserved Command set supported 15 Obsolete 14 1 = NOP command supported 13 1 = READ BUER command supported 12 1 = WRITE BUER command supported 11 Obsolete 10 1 = Host Protected Area feature set supported 9 1 = DEICE RESET command supported 8 1 = SERICE interrupt supported 7 1 = release interrupt supported 6 1 = look-ahead supported 5 1 = write cache supported 4 Shall be cleared to zero to indicate that the PACKET Command feature set is not supported 3 1 = mandatory Power Management feature set supported 2 1 = Removable Media feature set supported 1 1 = Security Mode feature set supported 0 1 = SMART feature set supported ersion 1.0 Page 11

12 Word alue / Description h H h h h Command sets supported 15 Shall be cleared to zero 14 Shall be set to one 13-9 Reserved 8 1 = SET MA security extension supported 7 Reserved 6 1 = SET EATURES subcommand required to spinup after power-up 5 1 = Power-Up In Standby feature set supported 4 1 = Removable Media Status Notification feature set supported 3 1 = Advanced Power Management feature set supported 2 1 = CA feature set supported 1 1 = READ/WRITE DMA QUEUED supported 0 1 = DOWNLOAD MICROCODE command supported Command set/feature supported extension 15 Shall be cleared to zero 14 Shall be set to one 13-2 Reserved 1 1 = SMART self-test supported 0 1 = SMART error logging supported Command set/feature enabled 15 Obsolete 14 1 = NOP command enabled 13 1 = READ BUER command enabled 12 1 = WRITE BUER command enabled 11 Obsolete 10 1 = Host Protected Area feature set enabled 9 1 = DEICE RESET command enabled 8 1 = SERICE interrupt enabled 7 1 = release interrupt enabled 6 1 = look-ahead enabled 5 1 = write cache enabled 4 Shall be cleared to zero to indicate that the PACKET Command feature set is not supported. 3 1 = Power Management feature set enabled 2 1 = Removable Media feature set enabled 1 1 = Security Mode feature set enabled 0 1 = SMART feature set enabled Command set/feature enabled 15-9 Reserved 8 1 = SET MA security extension enabled by SET MA SET PASSWORD 7 See Address Offset Reserved Area Boot, INCITS TR27: = SET EATURES subcommand required to spin-up after power-up 5 1 = Power-Up In Standby feature set enabled 4 1 = Removable Media Status Notification feature set enabled = Advanced Power Management feature set enabled 0 1 = DOWNLOAD MICROCODE command supported Command set/feature default 15 Shall be cleared to zero 14 Shall be set to one 13-2 Reserved 1 1 = SMART self-test supported 0 1 = SMART error logging supported ersion 1.0 Page 12

13 Word alue / Description 88 h Reserved 13 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 12 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 11 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 10 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 9 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 8 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected 7-6 Reserved 5 1 = Ultra DMA mode 5 and below are supported 4 1 = Ultra DMA mode 4 and below are supported 3 1 = Ultra DMA mode 3 and below are supported 2 1 = Ultra DMA mode 2 and below are supported 1 1 = Ultra DMA mode 1 and below are supported 0 1 = Ultra DMA mode 0 is supported h Time required for security erase unit completion h Time required for security erase unit completion h Current advanced power management value h Master Password Revision Code h Hardware reset result h Reserved h h h endor Specific h Reserved h Removable Media Status Notification feature set support 15-2 Reserved = Removable Media Status Notification feature set not supported 01 = Removable Media Status Notification feature supported 10 = Reserved 11 = Reserved Security status 15-9 Reserved 8 Security level 0 = High, 1 = Maximum 7-6 Reserved 5 1 = Enhanced security erase supported 4 1 = Security count expired 3 1 = Security frozen 2 1 = Security locked 1 1 = Security enabled 0 1 = Security supported Integrity word 15-8 Checksum 7-0 Signature Note: / = ixed/variable content = the content of the word is fixed and does not change. or removable media devices, these values may change when media is removed or changed. = the contents of the word is variable and may change depending on the state of the device or the commands executed by the device. = the content of the word may be fixed or variable. ersion 1.0 Page 13

14 3.3 ATA Command Description: SET EATURES (Eh) Table 12: eatures Register value and available operating mode alue Description 02h Enable write cache 03h Set transfer mode based on value in Sector Count register 55h Disable read look-ahead feature 82h Disable write cache 90h Disable write cache AAh Enable read look-ahead feature 3.4 SMART Command Support The J7 series SSD drive supports basic SMART command Set used to define some vendor -specific data to report spare/bad block numbers in each memory management unit. Table 13: SMART Command Set alue Command alue Command D0h Read Data attributes D1h Read attribute Threshold D2h Enable/Disable attribute auto save D3h Save attribute alues D8h Enable SMART operation D9h Disable SMART operation DAh Return Status SMART Attribute Sector The following 512 bytes defines the SMART format. Users can obtain the data using the Read Data command. Table 12: SMART Attribute Data Structure Byte Description 0-1 Data Structure revision number st attribute data nd -30 th Individual attribute data 362 Off-line data collection status 363 Self-test execution status Total time in seconds to complete off-line data collection 366 Reserved 367 Off-line data collection capability SMART capability 370 Error logging capability 371 Self-test failure checkpoint 372 Short self-test routine recommended polling time (in minutes) 373 Extended self-test routine recommended polling time (in minutes) Reserved 511 Data structure checksum ersion 1.0 Page 14

15 3.4.2 Supported SMART Attributes The following table summarizes the SMART attribute Menu. Table 13: SMART Attribute Menu Summary ID HE Attribute Name 1 01h Read Error Rate 2 02h Throughput Performance 3 03h Spin up time 5 05h Reallocated Sector Count 7 07h Seek Error Rate 8 08h Seek Time Performance 9 09h Power-On hours Count 10 0Ah Spin Retry Count 12 0Ch Device Power Cycle Count 168 A8h SATA PHY Error Count 170 AAh Bad Block Count 173 ADh Erase Count 175 Ah Bad Cluster Table Count 192 C0h Unexpected power Loss Count 194 C2h Temperature 197 C5h Current Pending Sector Count 240 0h Write Head ersion 1.0 Page 15

16 4.0 Physical Specifications Table 14: Physical Specifications Common Dimensions (mm) Symbol Min Nom Max A B C D E G H I G I A D E C B H igure 2: Physical Dimensions ersion 1.0 Page 16

17 5.0 Ordering Information Wintec Slim SATA SSD JM608 Series Table 15: Product Availability List & Naming Part Number NAND lash Type User Capacity W2ES004G1TA(I)-J71yy-zzz.aa MLC 3.5GB W2ES008G1TA(I)-J71yy-zzz.aa MLC 7.5GB W2ES016G1TA(I)-J71yy-zzz.aa MLC 15GB W2ES032G1TA(I)-J71yy-zzz.aa MLC 30GB W2ES050G1TA(I)-J71yy-zzz.aa MLC 50GB W2ES064G1TA(I)-J71yy-zzz.aa MLC 60GB W2ES128G1TA(I)-J71yy-zzz.aa MLC 120GB (I) Operating Temperature Blank : Commercial Temp I : Industrial Temp Note: I temp option only available with Micron Die (yy) lash IC Manufacturer and Die Revision M: Micron A: A die T: Toshiba C: C die : die (zzz) Component lash Configuration 002: 2-Nand, Single Die Package, 1-CE 02D: 2-Nand, Dual Die Package, 1-CE 2D2: 2-Nand, Dual Die Package, 2-CE 2Q2: 2-Nand, Quad Die Package, 2-CE 004: 4 Nand, Single Die Package, 1-CE 4D2: 4-Nand, Dual Die Package, 2-CE 4Q2: 4-Nand, Quad Die Package, 2-CE Note: Contact Wintec for current die Revision. (aa) irmware Revision/Options Please contact the factory for the latest firmware revisions, custom labeling and programming identification. ersion 1.0 Page 17

18 Contact Us (US & Int l) Wintec Industries OEM Sales 675 Sycamore Drive Milpitas, CA Ph: ax: About Wintec Industries, Inc.: Wintec Industries, founded in 1988, is headquartered in Milpitas, California. Wintec, an ODM/OEM solution provider, specializes in product designs and manufacturing, including lash modules (C, SD, USB, embedded lash, SSD, etc), DRAM modules (RDIMM, SODIMM, UDIMM), wireless products, modem products (embedded and USB), Advanced Digital Display products (ADD2 DI, HDMI, digital signage), and so on. With experienced engineering team in Silicon alley, Wintec provides a wide range of services and solutions for customers. Wintec is ISO certified. Important Notice: Wintec Industries makes no representations or warranties with respect to the contents of this datasheet and specifically disclaims any implied warranties of any product design for any particular purpose. Wintec Industries reserves the rights to revise this publication and to make changes from time to time in the content hereof without obligation of Wintec Industries to notify any person or organization of such revisions or change. ersion 1.0 Page 18