SED2C Series. Embedded Storage. Solutions 2.5 SATA SSD CSXXXXXXX-XXXXXXXX. Datasheet. Industrial. 5 March 2014

Transcription

1 Embedded Storage Industrial 2.5 SATA SSD SED2C Series CSXXXXXXX-XXXXXXXX Solutions 24, rue Gustave Madiot ZA Les Bordes BONDOUFLE Tél. : infos@6ta.fr ~ 1

2 Table of Contents 1. Product Description Product Overview Product Features System Requirement Power Requirement Operating System Interface Specifications Specification Physical Specifications Overlook Dimension Electronic Specifications Product Definition Pin Signal Assignment Support ATA Commands Error Detection and Correction Wear-Leveling Bad Blocks Management Mean Time between Failures (MTBF) Endurance Transfer Mode Ordering Information Contact Information

3 1. Product Description 1.1. Product Overview ACPI 2.5 SATA Solid Storage Disk (SSD) is the storage device based on NAND flash memory technology. This product complies with Serial ATA standard interface and suitable for data storage media and code storage device for embedded system and boot disk. By using 2.5 SATA SSD, it is possible to operate good performance for the systems, which have SATA interface. With small form factor, the applicable appliance can add or install SATA storage device on its Mother Board or Complete set Product Features Small form factor with Serial ATA Standard Interface connector. Memory Capacities SLC: 16GB / 32GB / 64GB MLC: 32GB / 64GB / 128GB / 256GB Compliant with Serial ATA Revision 2.6 specification with 1.5 Gbps/ 3.0 Gbps interface rate Compliant with ATA/ATAPI-8 Global Wear Leveling Hardware BCH ECC capable of correcting errors up to 72-bit/1KB Automatic sleep and wake-up mechanism to save power Embedded data buffer. High performance and reliability Noiseless and stable installation to system Operating voltage 5V operation Operating as Boot Disk Support S.M.A.R.T (Self-defined) Speed: Read up to 240 MB/s Write up to 185 MB/s Power Consumption < 1250mW Shock: Operating: 1,500G, duration 0.5ms, half sine wave Vibration: 20G peak, 10~2000Hz with 3axis Reliability Test Conditions Reference Standards Vibration 10Hz to 2K Hz, 20G, 3 axes IEC Mechanical Shock Duration: 0.5ms, 1500G, 3 axes IEC Table 1: Shock/Vibration Testing for 2.5 SATA SSD 3

4 Humidity: 0 C~55 C / 95% RH, 10cycles Operating Temperature: Standard Grade: 0 C ~ +70 C Storage Temperature: Standard Grade: -55 C to +95 C Fully Compliant with RoHS directive CE and FCC Compatibility 1.3. System Requirement The Host system which is connected to 2.5 SATA SSD should meet system requirements at minimum Power Requirement Voltage: DC +5V ± 5% Item Symbol Rating Unit Input voltage VIN +5DC ± 5% 500mA (max.) V Table 2: 2.5 SATA SSD Power Requirement Operating System Windows family. Linux family. DOS or embedded system Interface SATA 7+15 pins combo connector 1.4. Specifications Compliant with Serial ATA Revision 2.6 specification. Compliant with ATA/ATAPI-8 specification. Supports PIO modes 0,1,2,3 and 4 Supports Multi-Word DMA Modes 0, 1 and 2 Supports Ultra DMA Modes 0, 1, 2, 3, 4, 5, and 6 Supports ECC (Error Correction Code) Supports Bad Block Management Supports Wear-leveling 4

5 2. Specification 2.1. Physical Specifications Overlook The overlook views of 2.5 SATA SSD are illustrated in Figure 1. Figure 1: 2.5 SATA SSD Overlook Diagram 5

6 Dimension The Dimensions of 2.5 SATA SSD are illustrated in Figure 1 and described in Table 1. Figure 2: 2.5 SATA SSD Module Dimensions 6

7 Parameter Width Length Height Specifications 100mm ± 0.25mm 69.85mm ± 0.25mm 9.5mm ± 0.215mm Table 3: 2.5 SATA SSD Module Physical Dimension 2.2. Electronic Specifications Product Definition 2.5 SATA SSD is designed to operate and work as Data or Code Storage device by NAND Flash Memory and its Controller through Serial ATA Standard Interface to Host Systems. Figure 3: 2.5 SATA SSD Block Diagram 7

8 2.3. Pin Signal Assignment The signals assigned for Serial ATA applications are described in Table 4 Group Pin No. Function Description S1 GND Ground S2 RX+ Differential signal pair A S3 RX- Signal S4 GND Ground Segment S5 TX- Differential signal pair B S6 TX+ S7 GND Ground Key & Spacing P1 NC No connect on the device side P2 NC No connect on the device side P3 NC No connect on the device side P4 GND Ground P5 GND Ground P6 GND Ground P7 V5 5V power input Power P8 V5 5V power input Segment P9 V5 5V power input P10 GND Ground P11 GND Ground P12 GND Ground P13 NC No connect on the device side P14 NC No connect on the device side P15 NC No connect on the device side Table SATA SSD connector pin definition Figure 4: 2.5 SATA SSD Connector Pin Assignment 8

9 2.4. Support ATA Commands ATA Command Set - ATA Command Set summarizes the ATA command set with the paragraphs that follow describing the individual commands and the task file for each. No Command Set Code FR SC SN CY DH LBA General Feature Set 1 Execute Drive Diagnostic Mode 90h D - 2 Flush Cache E7h D - 3 Identify Device ECh D - 4 Initialize Device Parameters 91h - Y - - Y - 5 Read DMA C8h - Y Y Y Y Y 6 Read Multiple C4h - Y Y Y Y Y 7 Read Sector(s) 20h - Y Y Y Y Y 8 Read Verify Sector(s) 40h or 41h - Y Y Y Y Y 9 Recalibrate 10h 10 Seek 7xh - Y - Y Y Y 11 Set Feature EFh Y D - 12 Set Multiple Mode C6h - Y - - D - 13 Write DMA CAh - Y Y Y Y Y 14 Write Multiple C5h - Y Y Y Y Y 15 Write Sector(s) 30h - Y Y Y Y Y 16 NOP 00h D - 17 Read Buffer E4h D - 18 Write Buffer E8h D - Power Management Feature Set 19 Check Power Mode E5h or 98h D - 20 Idle E3h or 97h - Y - - D - 21 Idle Immediate E1h or 95h D - 22 Sleep E6h or 99h D - 23 Standby E2h or 96h D - 24 Standby Immediate E0h or 94h D - Security Mode Feature Set 25 Security Set Password F1h C Security Unlock F2h C Security Erase Prepare F3h C Security Erase Unit F4h C Security Freeze Lock F5h C Security Disable Password F6h C - - SMART Feature Set 31 SMART Disable Operations B0h D9h Y - Y Y - 32 SMART Enable/Disable Autosave B0h D2h Y - Y Y - 33 SMART Enable Operations B0h D8h Y - Y Y - 34 SMART Return Status B0h DAh Y - Y Y - 35 SMART Execute Off-Line Immediate B0h D4h Y - Y Y - 36 SMART Read Data B0h D0h Y - Y Y - Host Protected Area Feature Set 37 Read Native Max Address F8h D - 38 Set Max Address F9h - Y Y Y Y Y 9

10 No Command Set Code FR SC SN CY DH LBA 39 Set Max Set Password F9h - Y Y Y Y Y 40 Set Max Lock F9h - Y Y Y Y Y 41 Set Max Freeze Lock F9h - Y Y Y Y Y 42 Set Max Unlock F9h - Y Y Y Y Y 48-bit Address Feature Set 43 Flush Cache Ext EAh D - 44 Read Sector(s) Ext 24h - Y Y Y Y Y 45 Read DMA Ext 25h - Y Y Y Y Y 46 Read Multiple Ext 29h - Y Y Y Y Y 47 Read Native Max Address Ext 27h D - 48 Read Verify Sector(s) Ext 42h - Y Y Y Y Y 49 Set Max Address Ext 37h - Y Y Y Y Y 50 Write DMA Ext 35h - Y Y Y Y Y 51 Write DMA FUA Ext 3Dh - Y Y Y Y Y 52 Write Multiple Ext 39h - Y Y Y Y Y 53 Write Multiple FUA Ext CEh - Y Y Y Y Y 54 Write Sector(s) Ext 34h - Y Y Y Y Y Word Address Default Value Total Bytes h 2 F/V F X F X X F X F Table 5: ATA Command List Data Field Type Information General configuration Bit Significant with ATA definitions. 15 0:ATAdevice 14-8 Retired 7 1:removablemediadevice 6 Obsolete 5-3 Retired 2 Reserved 1 Retired 0 Reserved 1 XXXXh 2 X Default number of cylinders 2 C837h 2 V Reserved 3 00XXh 2 X Default number of heads 4-5 XXXXh 4 X Reserved 6 XXXXh 2 X Default number of sectors per track 7-8 XXXXh 4 V Reserved for assignment by the CFA 9 000Eh 2 X Reserved aaaa 20 F Serial number in ASCII (Right Justified) XXXXh 4 X Reserved Fh 2 X Reserved 10

11 2.5. Error Detection and Correction Highly sophisticated Error Correction Code algorithms are implemented. The hardware Error Correction Coding (ECC) engine executes parity generation and error detection/correction features, and enhances decoding throughput and data reliability. With multi-mode correction capability up to 72 bits, the powerful ECC engine is able to support the latest generation NAND Wear-Leveling Flash memory can be erased within a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit applies to each individual erase block in the flash device Bad Blocks Management Bad Blocks are blocks that contain one or more invalid bits whose reliability are not guaranteed. The Bad Blocks may be presented while the SSD is shipped, or may generate during the life time of the SSD. When the Bad Blocks is detected, it will be flagged, and not be used anymore. The SSD implement Bad Blocks management and replacement, Error Correct Code to avoid data error occurred. The functions will be enabled automatically to transfer data from Bad Blocks to spare blocks, and correct error bit. After the reserved block less than 10 of each channel, the SSD will be locked, and cannot be read and written anymore. Host can send a vendor ATA command to unlock the SSD for backup data or system from SSD Mean Time between Failures (MTBF) Failure Rate: The total number of failures within an item population, divided by the total number of life units expended by that population, during a particular measurement interval under stated condition. Mean Time between Failures (MTBF): A basic measure of reliability for repairable items: The mean number of life units during which all parts of the item perform within their specified limits, during a particular measurement interval under stated conditions. Product Condition MTBF (Hours) 2.5 SATA SSD LT Telcordia SR-332 GB, 25 C >2,000,000 Table6: 2.5 SATA SSD LT MTBF 11

12 2.9. Endurance Data Retention: 10 years. Wear-Leveling Algorithm: Support. Bad Blocks Management: Support. Error Correct Code: Support Transfer Mode 2.5 SATA SSD support following transfer mode: PIO Mode 0~4. Ultra DMA 0~6. Serial ATA I 1.5Gbps Serial ATA II 3.0Gbps 3. Ordering Information Model Capacities Normal-Temp Wide-Temp SED2C 16GB 16GB CSC016GR1-F507A006 CSI016GR1-F507A006 SED2C 32GB 32GB CSC032GR1-F607A006 CSI032GR1-F607A006 SED2C 64GB 64GB CSC064GR1-F607A006 CSI064GR1-F607A006 SED2C-M 32GB 32GB CSC032GR1-G607A008 CSI032GR1-G607A008 SED2C-M 64GB 64GB CSC064GR1-G707A008 CSI064GR1-G707A008 SED2C-M 128GB 128GB CSC128GR1-G807A008 CSI128GR1-G807A008 SED2C-M 256GB 256GB CSC256GR1-G807A008 CSI256GR1-G807A008 SED2C-M 16GB 32GB CSC016GR1-E607A007 SED2C-M 32GB 32GB CSC032GR1-E607A007 SED2C-M 64GB 64GB CSC064GR1-E607A007 SED2C-M 128GB 128GB CSC128GR1-E607A Contact Information ACPI, a storage business company, specializes in the design and marketing of SSD, EDM, and Industry CF products. For further information, please reach us at the following contact information: ACPi Digital Co., Ltd. TEL: FAX: sales@acpigroup.com Address: 11F.-3, No.186, Jian 1st Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) 12