CMOS Setup for EPoX EP-3VWB Motherboard

Size: px

Start display at page:

Download "CMOS Setup for EPoX EP-3VWB Motherboard"

Cuthbert Hawkins
6 years ago
Views:

1 CMOS Setup for EPoX EP-3VWB Motherboard Immediately after the memory test, hit the [Delete] key to enter CMOS setup. (This must be done on a PC keyboard connected on the back of the RADAR.) 1. Choose Load Optimized Defaults, hit [Enter], [Y], [Enter] to load the defaults. Esc : Quit F10 : Save & Exit Setup Load Optimized Detaults (Y/N)? : Select Item 2. a) Select Standard CMOS Change Date (mm:dd:yy) to current date Change Time (hh:mm:ss) to current time Change Halt On to No Errors. Date (mm:dd:yy) Tue, April 29 Time (hh:mm:ss) 2 : 11 : 47 >IDE Primary Master >IDE Primary Slave >IDE Secondary Master device >IDE Secondary Slave Drive A Drive B Model # of system drive Model # of backup 1.44M, 3.5 in Video Halt On Base Memory Extended Memory EGA/VGA No Errors 640K Parallels memory test iz Technology Corporation

2 3. a) Select Advanced BIOS Change First Boot Device to HDD-0 Change Second Boot Device to Floppy Change Third Boot Device to Change Boot Other Device to Virus Warning CPU Internal cache External Cache CPU L2 Cache ECC Checking Processor number Feature Quick power on self test First Boot Device HDD-0 Second Boot Device Floppy Third Boot Device Boot other device Swap floppy drive Boot up floppy seek Boot up Numlock Status ON Gate A20 Option Normal Typematic Rate Setting Typematic Rate(Chars/sec) 6 Security Option Setup OS Select For DRAM>64MB NON-OS2 4. a) Select Advanced Chipset Change Video Ram Cacheable to Change USB Keyboard Support to Bank 0/1 DRAM Timing SDRAM Fast Bank 2/3 DRAM Timing SDRAM Fast SDRAM Cycle Length 3 Bank Interleave Memory Hole P2C/C2P Concurrency Fast R-W Turn Around System BIOS Cacheable Video RAM cacheable Frame Buffer Size 8M AGP Aperture Size 64M OnChip USB OnChip USB 2 USB Keyboard Support OnChip Sound OnChip Modem Disable CPU to PCI Write Buffer PCI Dynamic Bursting PCI Master 0 WS Write iz Technology Corporation

3 5. a) Select Integrated Peripherals, hit [Enter] Change Sound Blaster to Change SB IRQ Select to IRQ 10 Onboard Parallel Port 378/IRQ7 Onboard Parallel Mode ECP/EPP ECP Mode Uses DMA 3 Parallel Port EPP Type EPP1.9 Onboard Legacy Audio Sound Blaster SB I/O Base Address 220H SB IRQ Select IRQ 10 SB DMA Select DMA 1 MPU a) Select PnP/PCI Configurations, hit [Enter] Change Resources Controlled By to Manual Move cursor to IRQ Resources and hit [Enter]. PNP OS Installed Reset Configuration Data Resources Controlled By >IRQ Resources >DMA Resources PCI/VGA Palette Snoop Assign IRQ For VGA Assign IRQ For USB No Manual Press Enter Press Enter c) Change IRQ-5 assigned to Legacy ISA, hit [Esc] d) Hit [Esc] to exit IRQ-3 assigned to PCI/ISA PnP IRQ-4 assigned to PCI/ISA PnP IRQ-5 assigned to Legacy ISA IRQ-7 assigned to PCI/ISA PnP IRQ-9 assigned to PCI/ISA PnP IRQ-10 assigned to PCI/ISA PnP 7. Select Save & Exit Setup, hit [Enter], [Y], [Enter] to save and boot RADAR. SAVE AND EXIT>SET SETUP SUPERVISOR (Y/N)? PASSWORD END of CMOS setup for EpOX EP-3VWB+ motherboard iz Technology Corporation

4 CMOS Setup for DFI CA64-TC Motherboard Immediately after the memory test, hit the [Delete] key to enter CMOS setup. (This must be done on a PC keyboard connected on the back of the RADAR.) 1. Choose Load Optimized Defaults, hit [Enter], [Y], [Enter] to load the defaults. Esc : Quit F10 : Save & Exit Setup Load Optimized Detaults (Y/N)? : Select Item 2. a) Select Standard CMOS Change Date (mm:dd:yy) to current date Change Time (hh:mm:ss) to current time Change Halt On to No Errors Date (mm:dd:yy) Tue, April 29 Time (hh:mm:ss) 2 : 11 : 47 >IDE Primary Master >IDE Primary Slave >IDE Secondary Master device >IDE Secondary Slave Drive A Drive B Model # of system drive Model # of backup 1.44M, 3.5 in Video Halt On Base Memory Extended Memory EGA/VGA No Errors 640K Parallels memory test iz Technology Corporation

5 3. a) Select Advanced BIOS Change First Boot Device to HDD-0 Change Second Boot Device to Floppy Change Third Boot Device to Change Boot Other Device to Change Boot up floppy seek to Virus Warning CPU Internal cache External Cache CPU L2 Cache ECC Checking Processor number Feature Quick power on self test First Boot Device HDD-0 Second Boot Device Floppy Third Boot Device Boot other device Swap floppy drive Boot up floppy seek Boot up Numlock Status ON Gate A20 Option Normal Typematic Rate Setting Typematic Rate(Chars/sec) 6 Security Option Setup OS Select For DRAM>64MB NON-OS2 4. a) Select Advanced Chipset Change DRAM Clock to Host CLK Change USB Keyboard Support to DRAM Timing Fast SDRAM Cycle Length 3 DRAM Clock Host CLK Memory Hole P2C/C2P Concurrency Fast R-W Turn Around AGP Aperture Size 64M AGP-4X Mode AGP Fast Write OnChip USB USB Keyboard Support CPU to PCI Write Buffer PCI Dynamic Bursting PCI Master 0 WS Write PCI Delay Transaction iz Technology Corporation

6 5. a) Select Integrated Peripherals, hit [Enter] b) Change Onboard Legacy Audio to ECP Mode Use DMA 3 Parallel Port EPP Type EPP1.9 OnChip Sound Onboard Legacy Audio Sound Blaster SB I/O Base Address 220H 6. a) Select PnP/PCI Configurations, hit [Enter] Change Resources Controlled By to Manual Move cursor to IRQ Resources and hit [Enter]. PNP OS Installed Reset Configuration Data Resources Controlled By >IRQ Resources >DMA Resources PCI/VGA Palette Snoop Assign IRQ For VGA Assign IRQ For USB No Manual Press Enter Press Enter c) Change IRQ-5 assigned to Legacy ISA, hit [Esc] d) Hit [Esc] to exit IRQ-3 assigned topci/isa PnP IRQ-4 assigned to PCI/ISA PnP IRQ-5 assigned to Legacy ISA IRQ-7 assigned to PCI/ISA PnP IRQ-9 assigned topci/isa PnP IRQ-10 assigned to PCI/ISA PnP 7. Select Save & Exit Setup, hit [Enter], [Y], [Enter] to save and boot RADAR. SAVE AND EXIT>SET SETUP SUPERVISOR (Y/N)? PASSWORD END of CMOS setup for DFI CA64-TC motherboard. iz Technology Corporation

7 CMOS Setup for Gigabyte Motherboard Immediately after the memory test, hit the [Delete] key to enter CMOS setup. (This must be done on a PC keyboard connected on the back of the RADAR.) 1. Choose Load Performance Defaults, hit [Enter], [Y], [Enter] to load the defaults. >BIOS FEATURES SETUP >CHIPSET FEATURES SETUP SETUP >LOAD BIOS DEFAULTS >LOAD PERFORMANCE DEFAULTS Esc : Quit F10 : Save & Exit Setup Load Optimized Detaults (Y/N)? >SUPERVISOR PASSWORD >USER PASSWORD >IDE HDD AUTO DETECTION : Select Item 2. a) Select Standard CMOS >BIOS FEATURES SETUP >CHIPSET FEATURES SETUP SETUP >LOAD BIOS DEFAULTS>LOAD PERFORMANCE DEFAULTS >SUPERVISOR PASSWORD >USER PASSWORD >IDE HDD AUTO DETECTION Change Date (mm:dd:yy) to current date Change Time (hh:mm:ss) to current time Date (mm:dd:yy) Tue, April 29 Time (hh:mm:ss) 2 : 11 : 47 >IDE Primary Master >IDE Primary Slave >IDE Secondary Master >IDE Secondary Slave Drive A Drive B Model # of system drive Model # of backup device 1.44M, 3.5 in Video EGA/VGA 3. a) Select BIOS Features Setup, hit [Enter] >BIOS FEATURES SETUP >CHIPSET FEATURES SETUP SETUP >LOAD BIOS DEFAULTS>LOAD PERFORMANCE DEFAULTS >SUPERVISOR PASSWORD >USER PASSWORD >IDE HDD AUTO DETECTION b) Change Boot Sequence to C, A, SCSI Virus Warning Processor number Feature Boot from LAN first Boot Sequence C,A,SCSI VGA boot from AGP Boot up floppy seek Boot up Numlock Status ON Memory parity check Typematic Rate Setting Typematic Rate(Chars/sec) 6 Typematic Delay (Msec) 250 Security Option Setup PCI/VGA palette snoop iz Technology Corporation

8 5. a) Select PnP/PCI Configuration, hit [Enter] >BIOS FEATURES SETUP >CHIPSET FEATURES SETUP SETUP >LOAD BIOS DEFAULTS>LOAD PERFORMANCE DEFAULTS >SUPERVISOR PASSWORD >USER PASSWORD >IDE HDD AUTO DETECTION Change Resources Controlled By to Manual Change IRQ-5 assigned to to Legacy ISA PNP OS Installed Resources Controlled By Reset Configuration Data No Manual IRQ-3 assigned to PCI/ISA PnP IRQ-4 assigned to PCI/ISA PnP IRQ-5 assigned to Legacy ISA IRQ-7 assigned to PCI/ISA PnP IRQ-9 assigned to PCI/ISA PnP IRQ-10 assigned to PCI/ISA PnP 6. Select Save & Exit Setup, hit [Enter], [Y], [Enter] to save and boot RADAR. >BIOS FEATURES SETUP >SUPERVISOR PASSWORD >CHIPSET FEATURES SETUP >USER PASSWORD SAVE AND EXIT SETUP (Y/N)? SETUP >IDE HDD AUTO DETECTION >LOAD BIOS DEFAULTS>LOAD PERFORMANCE DEFAULTS END of CMOS setup for Gigabyte GA-6VA7+ motherboard. iz Technology Corporation

Tech Note #51 Title: Setting BIOS settings in Orion Motion Controllers Date: April 24, 2003

19 Linden Park, Rochester, NY 14625 (585) 385-3520 Fax (585) 385-5999 Tech Note #51 Title: Setting BIOS settings in Orion Motion Controllers Date: April 24, 2003 Orion motion controllers use a PC motherboard