Digital Counter. DIN 48 x 48 mm Counters with Easy-to-use Functions

Transcription

1 Digital Counter DIN 8 x 8 mm Counters with Easy-to-use Functions Designed with an emphasis on ease of operation. All models (except -A, and -SA type) equipped with prescale function which displays in units of actual physical parameters (length, volume, etc.). -C/SC large/small discrimination mode useful for positioning and production control. igh-speed response allows 5, counts per second. igh-visibility CD display with built-in backlight. Online change of set value possible. Meets U and CSA standards. Conforms to IEC11-1/EN11-1 standard. -S short type only mm deep. -8/11 plug-in types can be DIN-track mounted. -8 has a built-in power supply reset function. Conforms to EMC standards. Six-language instruction manual provided. 1

2 Ordering Information -A/B/C Counters Basic type (without backlight) Standard (with backlight) ±Range type (with backlight) One Stage One Stage Two Stages One Stage Two Stages No-voltage Voltage No-voltage Voltage No-voltage Voltage No-voltage Voltage No-voltage Voltage External power supply Outputs Control supply voltage Digits Contact 1 to / to AC 5/ z -A -A -AV Transistor VAC 1 to / to AC 5/ z -A -AS -A -AS -AV -AVS VAC -AS -AVS VDC (1 ma) Contact 1 to AC 5/ z VAC to VDC -B -B -B -BV -BW -BV -BW -BW -BW -BW -BW -BWV -BWV -BWV -BWV -C -C -CV -CV -CW -CW -CWV -CWV Transistor 1 to AC 5/ z -BS -BS -BVS - BVS -BWS -BWS - BWVS - BWVS -CS - CVS -CWS -CWVS VAC to VDC -BS - BVS -BVS -BWS -BWS - BWVS - BWVS -CS -CVS -CWS -CWVS 1 to AC 5/ z -BG -BG -BVG - BVG -BWG -BWG - BWVG - BWVG -CG -CVG -CWG -CWVG VDC (5 ma) Contact VAC to VDC 1 to AC 5/ z -BG -BSG - BSG -BVG - BVSG - BVG - BVSG -BWG - BWSG -BWG - BWSG - BWVG - BWVG - - BWVSG BWVSG -CG - CSG -CVG -CVSG -CWG -CWSG -CWVG -CWVSG Transistor VAC to VDC -BSG - BVSG - BVSG - BWSG - BWSG - - BWVSG BWVSG -CSG -CVSG -CWSG -CWVSG

3 -S (Short Body) -S Basic type (with backlight) Standard (with backlight) ±Range type (with backlight) One Stage One Stage Two Stage One Stage Two Stage No-voltage No-voltage No-voltage No-voltage No-voltage External power supply Outputs Control supply voltage Digits Contact Transistor to VDC -SA -SAS -SA -SAS -SB -SBS -SB -SBS -SBWS -SBWS -SC -SCS -SCWS -8/11 (Plug-in Socket) -8/11 Standard (with backlight) One Stage Power Supply Type (-8) Memory Backup Type (-11) External power supply Outputs Control power source Digits Contact 1 to AC 5/ z VAC to VDC Transistor 1 to AC 5/ z VAC to VDC -8S -8S -11S -11S Note: Specify both the model and control supply voltage when ordering. With shock prevention cover types are named

4 Model Number egend This model legend does not mean that all combinations of the following features are available Backlight 7. External Power Supply (Only for -B or -C type). Control Output (Only for models in size 8 x 8) 5.. Setting 3. No. of. Type 1. Depth 1. Depth S: Short (Only for models in size 8 x 8) : Not short. Type A: Basic type (Only for models of size 8 x 8) B: Standard type C: ± Range type (Only for -digit display models) 8: Plug-in power reset (Only for models of size 8 x 8) 11: Plug-in power failure backup (Only for models of size 8 x 8) 3. No. of : (Only for models of size 8 x 8) :. Setting W: -stage setting (Only for -B or -C type) : 1-stage setting Accessories (Order Separately) Name Soft Cover (with two mounting clips) Shock Prevention Cover Panel Mounting Bracket Surface Mounting Bracket Flush Mounting Bracket Model Y9A-8F1 Y9A-8T Y9F-3 PCF-8 P3G-8 5. V: Voltage (Not for short body or plug-in type models) : No-voltage. Control Output (Only for models of size 8 x 8) S: Transistor output : Contact output 7. External Power Supply (Only for -B or -C type) G: -VDC power supply : Other than -VDC power supply 8. Backlight : Short body with backlight (Only for models of size 8 x 8) : Other than short body with backlight Operating Environment The counter has a water-resistive structure, thus preventing the internal circuitry from drops of water that may penetrate through the space between the keys and operating panel. Before operating with wet or oily hands, however, put a soft cover (sold separately) onto the operating panel. Although the soft cover protects the instrument to IPS, avoid places where the counter is directly exposed to water or oil. A Y9F-3 Panel Mounting Adaptor is supplied with each counter. (It can also be ordered independently.)

5 Soft Cover/Y9A-8F1 Shock Prevention Cover/Y9A-8T Conforms to VDE 1/P1 Panel Mounting Bracket/Y9F-3 Surface Mounting Bracket/ PCF-8 Flush Mounting Bracket/ P3G-8 Y9F-3 P3G PCF-8 Surface Mounting Bracket/ PF-11 Flush Mounting Bracket/ P3GA-11 Y9F-3 P3GA PCF-11 Note: Models with a Shock Prevention Cover can be ordered by adding -5 to the end of the model number. Example: -BW-5 (1 to AC, 5/ z) (except plug-in type, -8/11) 5

6 Specifications -A/B/C Classification Mounting method Model -A/A (Basic type) -B/B (Standard type) -C (±Range type) External connections Enclosure ratings Approved standards modes* Digital preset counter Flush mounting Screw terminals IP5 (panel surface) U58, CSA C. No.1, conforms to EN11-1/IEC11-1, conforms to EN581- and EN58- Up (incrementing), Down (decrementing), and reversible (Up/Down) Up/Down A (command s), Up/Down B (individual s), Up/Down C (phase difference s) Reversible Up/Down A (command s), Up/Down B (individual s), Up/Down C (phase difference s) Output modes* N, F N, F, C, R, K, P, Q, A K, D,, system External and manual resets External, manual and automatic External and manual resets resets (internal according to C, R, P, and Q mode operation) Prescaling function Yes (.1 to ) Decimal point adjustment Yes (Rightmost 3 ) Sensor power supply VDC or VDC (according to model) signals Count and reset Count, reset, and key protection method No-voltage : Via opening No-voltage : Via opening and closing of contact and closing of contact Voltage : Via high and low signal voltages (key protection Voltage : Via high and is no-voltage only) low signal voltages Control outputs SPST-NO contact or transistor 1 stage model: SPST-NO contact or transistor (NPN open (NPN open collector) output collector) output stage model: stages of SPST-NO contact or transistor (NPN open collector) output Display CD CD with backlight Digits ( to 999,999), ( to 9,999) 5 negative and positive (-99,999 to 999,999) Memory backup Backup time for power interruption: Approx. 1 years at C *Refer to timing charts for and output mode operation.

7 -S/8/11 Model Classification -SA/SA (Basic type) Digital preset counter -SB/SB (Standard type) -SC (±Range type) -8/8 (Standard type) -11/11 (Standard type) Mounting method Flush mounting Flush mounting, surface mounting External connections Screw terminals Socket Enclosure ratings Approved standards modes* IP5 (panel surface) U58, CSA C. No.1, conforms to EN11-1/IEC11-1, EN581- and EN58- Up (incrementing), Down (decrementing), and reversible (Up/Down) Up/Down A (command s), Up/Down B (individual s), Up/Down C (phase difference s) Output modes* N, F N, F, C, R, K, P, Q, A system External and manual resets External, manual, automatic resets (internal according to C, R, P, and Q mode operation) Reversible Up/Down A (command s), Up/Down B (individual s), Up/Down C (phase difference s) Incrementing, decrementing, and reversible (Up/Down) Up/Down A (command s), Up/Down B (individual s), Up/Down C (phase difference s) K, D,, N, F, C, R, K, P, Q, A External and manual resets External, manual, power supply, and automatic resets (internal according to C, R, P, and Q mode operation) External, manual, automatic resets (internal according to C, R, P, and Q mode operation) Prescaling function Yes (.1 to ) Decimal point Yes (Rightmost 3 ) adjustment signals Count and reset Count, reset, and key protection Count and reset Count, reset, and key protection method No-voltage : Via opening and closing of contact Control outputs SPST-NO contact 1 stage model: SPST-NO contact or SPST-NO contact SPDT-NO contact or transistor (NPN transistor (NPN open collector) output or transistor (NPN or transistor (NPN open collector) stage model: DPST-NO contact or open collector) open collector) output transistor (NPN open collector) output output output Display CD with backlight Digits ( to 999,999) ( to 9,999) Memory backup 5 negative and positive (-99,999 to 999,999) Backup time for power interruption: Approx. 1 years at C ( to 999,999) ( to 9,999) 7

8 Ratings -A/B/C Model -A/A (Basic type) -B/B (Standard type) -C/C (±Range type) Rated supply voltage Operating voltage range Current consumption Max. counting speeds 1 to AC/ to AC, 5/ z, VAC 85% to 11% of rated voltage Approx..A (at 5 z, AC); approx. 1.3 VA (at 5 VAC) * 3/1k/5kcps (same setting for CP1 and CP) Min. pulse width for external reset: ms, manual reset Key protection Response time: 1 s 1 to AC, 5/ z, VAC/ to VDC (ripple: % max.) Approx.. VA (at 5 z, AC); approx. 3. W (at VDC)** Min. pulse width for external reset: 1 or ms, manual reset One-shot time 1, 5, 1,, and 5 ms (separate setting for stages 1 and ) Count, reset s No-voltage ON impedance: 1 kω max. (Approx. ma when Ω) ON residual voltage: V max. OFF impedance: 1 kω max. Voltage ( resistance: approx..7 kω) igh level:.5 to 3DC ow level: to VDC Key protection No-voltage ON impedance: 1 kω max. (Approx. ma when Ω) ON residual voltage: 1 V max. OFF impedance: 1 kω min. Control outputs Contacts: 3 A at 5AC, resistance load (cos φ = 1) Transistor output: Open collector 1mA at 3DC max. residual voltage V max. (Approx. 1 V) External power supply 1 ma, VDC ±1% (5% ripple max.) 5 ma, VDC ±1% (5% ripple max.) *When power is turned ON, approx. A ( VAC) inrush current flows for about ms. **When power is turned ON, approx. 5 A (AC), 8 A ( VDC, VAC) inrush current flows for about ms. -S/8/11 Model -SA/SA (Basic type) -SB/SB (Standard type) -SC (±Range type) -8/8 (Standard type) -11/11 (Standard type) Rated supply voltage to VDC (contains % ripple max.) 1 to AC, 5/ z, VAC/ to VDC (ripple: % max.) Operating voltage range 85% to 11% of rated voltage Current consumption Approx. 1.3 W (at VDC) * Approx..8 VA (at 5 z, AC) * approx. 1.3 W (at VDC) ** Max. counting speeds (CP1, CP count ) 3/1k/5kcps (same setting for CP1 and CP) Min. pulse width for external reset: ms manual reset Min. pulse width for external reset: 1 or ms manual reset Key protection Response time: approx. 1 s One-shot time 1, 5, 1,, and 5 ms (separate setting for stages 1 and ) Count, reset s No-voltage ON impedance: 1 kω max. (Approx. ma when Ω) ON residual voltage: V max. OFF impedance: 1 kω max. Key protection No-voltage ON impedance: 1 kω max. (Approx. ma when Ω) ON residual voltage: 1 V max. OFF impedance: 1 kω min. Min. pulse width for external reset: 1 or ms, manual reset, power reset:.5 s 1, 5, 1,, and 5 ms Min. pulse width for external reset: 1 or ms manual reset No-voltage ON impedance: 1 kω max. (Approx. ma when Ω) ON residual voltage: 1 V max. OFF impedance: 1 kω min. Control outputs Contacts: 3 A at 5AC, resistance load (cos φ= 1) Transistor output: Open collector 1mA at 3DC max. residual voltage V max. (Approx. 1 V) *When power is turned ON, approx. 5 A ( VDC, AC) inrush current flows for about ms. 8

9 **When power is turned ON, approx. 8 A ( VDC, VAC) inrush current flows for about ms. Characteristics Insulation resistance Dielectric strength Impulse withstand voltage Noise immunity Static immunity Vibration resistance Shock resistance ife expectancy Ambient temperature Ambient humidity Operating: 35% to 85% 1 MΩ min. (at 5DC) (between current-carrying terminal and exposed non-current-carrying metal parts, and between non-continuous contacts),ac, 5/ z for 1 min (between current-carrying terminal and exposed non-current-carrying metal parts) for 1 to AC type 1,AC for VAC/ to VDC type and for transistor output type 3 kv (between power terminals) for 1 to AC type, 1 kv for VAC/ to VDC.5 kv (between current-carrying terminal and exposed non-current-carrying metal parts for 1 to VAC type, 1.5 kv for VAC/ to VDC. ± kv (between power terminals) and ± (between terminals), square-wave noise by noise simulator (pulse width: 1 ns/1 µs, 1-ns rise) ±8 (between power terminals) for -S type Destruction: 15 kv Malfunction: 8 kv Destruction: 1 to 55 z with.75-mm single amplitude each in three directions Malfunction: 1 to 55 z with.5-mm single amplitude each in three directions Destruction: 3 m/s (Approx. 3G) each in three directions. Malfunction: 1 m/s (Approx. 1G) each in three directions. Mechanical: 1 million operations min. Electrical: 1, operations min. 5A at 5AC in load resistance Operating: 1 C to 55 C (with no icing) Storage: 5 C to 5 C (with no icing) EMC (EMI): EN581- Emission Enclosure: EN5511 Group 1 class A Emission AC Mains: EN5511 Group 1 class A (EMS): EN58- Immunity ESD: Case color Weight I/O Functions EN1--: kvcontact discharge 8 kv air discharge Immunity RF-interference: ENV51: 1/m (Amplitude-modulated, 8 Mz to 1 Gz) 1/m (Pulse-modulated, 9 Mz) Immunity Conducted Disturbance: ENV511 1 (.15 to 8 Mz) Immunity Burst: EN1--: kv power-line kv I/O signal-line ight gray (Munsell 5Y7/1) -A/A (AC type): approx. 3 g; -B/B/C: approx. 17 g -S/S: approx. g; -8/8/11/11: approx. 15 g s CP1/CP Count signal s. Up, Down, and Up/Down (command, individual, or phase difference) s accepted. Key protection (See note) s present value. (to zero in Up modes, to preset with 1-stage models in Down mode, and to preset with -stage models.) Count s are not accepted while reset is ON. indicator lit while reset is ON. Makes keys inoperative according to key protection level. Key protection indicator lit while key protection is ON. Effective when power supply is turned off. Effective when protect terminals are shorted. Outputs OUT 1. Outputs made according to designated output mode when corresponding preset is reached. Note: Not set for the Basic type and -8. 9

10 Engineering Data ife Expectancy of Contacts Electrical ife Expectancy (Resistive oad) Electrical ife Expectancy (Inductive oad) No. of operations (x 1 3 ) 5AC (cos φ = 1) 3DC (cos φ = 1) No. of operations (x 1 3 ) 5AC (cos φ =.) 3DC (/R = 7 ms) oad current (A) oad current (A) Reference: A current of.15 A max. can be switched at 5 VDC (cos φ =1) and a current of.1 A max. can be switched if /R = 7 ms. In both cases, a life of 1, operations can be expected. Nomenclature Indicator 1. Power indicator. Key protection indicator 3. Control output indicator OUT: 1 stage OUT1, OUT: stages. Present value (character height: 8 mm) (Zeroes suppressed) 5. Set value (character height: mm) (Indicates data in function setting mode). Set value 1, stage indicator Operation Key 7. Increment Keys (1 to ) (Used to change the corresponding digit of the set value. Increment Key () of -C/SC also can be switching for ±code. Used to change data in the function setting mode.) 8. Display Key (Switches to the setting displays. For stage model, switch set value 1,.) 9. Mode Key (Switches from run mode to function setting mode. Changes items in the function setting mode. 1. Key (s present value and outputs.) Indicator Operation Key 1. Power indicator. Key protection indicator 3. Control output indicator OUT: 1 stage OUT1, OUT: stages. Present value (character height: mm) (eading zeros suppressed) 5. Set value (character height:.5 mm) (Indicates value in function Setting Mode). Set value stage 1 and indicators Increment Keys (1 to ) (Used to change the corresponding digit of the set value. Used to change data in the function Setting Mode.) 8. Display Key (Switches to the setting displays. For -stage models, switches set value 1 and.) 9. Mode Key (Switches from Run Mode to Setting Mode. Changes items in the Setting Mode. 1. Key (s present value and outputs.) 1

11 Operation Factory Settings The following table shows the timer settings when it is shipped. Please change the settings as necessary to suit the system before operation. Settings and the display receive power from the internal battery and are therefore unaffected by external power interruptions. -A/B/C Model -A/A (Basic type) -B/B (Standard type) -C (±Range type) Present value Presets mode Up Up Up/Down C (phase difference) Output mode N N K Output time (OD) (OD) 5 ms Output 1 time OD 5 ms Counting speeds 3 cps 3 cps 3 cps Min. reset time ( ms) ms ms Decimal point (no fractions) Far right (no fractions) Far right (no fractions) Prescale (1,) 1, 1, Key protection level KP-1 KP-1 Note: With the initial settings, there will be no output even if the power supply is connected. External s and outputs cannot be used without a power supply. -S/8/11 Model -SA/SA (Basic type) -SB/SB (Standard type) -SC (±Range type) Present value -8/11/8/11 (Standard type) Presets mode Up Up Up/Down C (phase Up difference) Output mode N N K N Output time (OD) (OD) 5 ms (OD) Output 1 time OD 5 ms Counting speeds 3 cps 3 cps 3 cps 3 cps Min. reset time ( ms) ms ms ms Decimal point (no fractions) Far right (no fractions) Far right (no fractions) Far right (no fractions) Prescale (1,) 1, 1, 1, Key protection level KP-1 KP-1 KP-1 (-11 only) Note: With the initial settings, there will be no output even if the power supply is connected. External s and outputs cannot be used without a power supply. 11

12 Operational Overview Run mode Setting mode Present value, set value 1 Press the MODE Key mode Press the DISPAY Key Present value, set value Press the DISPAY Key Output mode Output time Press the MODE Key Press the MODE Key Output 1 time Press the MODE Key Press the MODE Key Press the MODE Key Count speed Press the MODE Key Min. reset time Press the MODE Key Decimal point Press the MODE Key Prescale value Press the MODE Key Key protection level Note: Set values are changed with the Increment Keys (1 to ()). Setting Item Table Mode Setting Applicable model Description Setting procedure item -A/ A/ SA/ SA -B/ B/ SB/ SB -C/ SC -8 /8-11/ 11 Run mode Function setting mode Set value 1, No Yes Yes No No Compared to the present value. Determines the timing of the control output according to the output mode. The DISPAY Key switches between set value 1 and. (-stage model only.) mode Yes Yes Yes Yes Yes Determines the mode selecting from Up, Down, Up/Down modes. Sequence when changing a digit using the Increment Keys (1 to ()).... Note: (-) is -C and -SC type (Increment Key ) only. Press keys 1 to () to change the displayed mode. * * (Up) (Down) (Up/Down A) (Up/Down B) (Up/Down C) *No mode for -C/SC type.

13 Mode Setting Applicable model Description Setting procedure Function setting mode item Output mode -A/ A/ SA/ SA -B/ B/ SB/ SB -C/ SC -8 /8-11/ 11 Yes Yes Yes Yes Yes Determines the form of the control output. (Refer to the present value vs. output diagrams on pages 1 to 18.) Determines the output time for control output (Output ). Press keys 1 to () to change the displayed mode. -A/SA (N) (F) -B/SB/8/11 (N) (F) (C) (R) (K) (P) (Q) (A) -C/SC * * -stage model only. (K) (D) () () Press keys 1 to () to change the Output time. (Applicable to output modes C, R, K, P, Q, and A only. Output time 1 (-stage model only) Count speed Min. reset time Decimal point Prescale value Key protection level No Yes Yes No No Determines the output time of the control output (OUT 1) for -stage model counters. Yes Yes Yes Yes Yes Switches the count filter to protect against errant counts due to interference. No Yes Yes Yes Yes Determines the initial signal width of the external reset. No Yes Yes Yes Yes Determines the decimal point position of the present and set values. No Yes Yes Yes Yes Can calculate and display a physical parameter (volume, length, etc.) from the present value. For example, if one count represented a movement of. mm, the prescale value would be.. Values from.1 to are possible. No Yes Yes No Yes ocks certain keys to prevent accidental operation. The key protection level, kp-1 to kp-, determines which keys are locked when the key protection is ON. The locked keys are crossed out in the diagram on the right. ms ms ms ms ms Press keys 1 to () to change the displayed mode. * ms ms ms ms ms *-BW/SBW only. Press keys 1 to () to change the displayed mode. (3cps) (1kcps) (5kcps) Press keys 1 to () to change the displayed mode. (1 ms) ( ms) Move the decimal point position from left to right with keys, 1 to (). Change the value of the with the corresponding keys, 1 to () Sequence when changing the key protection level using the Increment Keys (1 to ()). <KP 1> <KP 3> <KP > <KP-> Note: Settings changed in setting mode are not effective until run mode is entered. 13

14 Examples Run Mode Changing the Set Value 1. Press the DISPAY Key to change the displayed preset value 1 and during operation.. Change the set value from 5 to 1,5. Pressing keys 1 through (1 through for -digit models) increments the corresponding column by1. Non-significant zeros are normally not shown on the set value display. Setting Mode Changing Settings in the Function Setting Mode 1. Press the MODE Key to switch from run mode to setting mode. The Counter will continue operation if switched from run mode to function setting mode during operation. The MODE Key will be locked if the key protection function is enabled. Settings changed in the function setting mode are not effective until run mode is entered. As the operating conditions will change in this case, always reset operation with the RESET Key or a reset. 3. Changing the selected item Press the MODE Key until the desired item appears Change the item setting by pressing keys 1 through (1 through for -digit models). (Press the DISPAY Key to switch back from function setting mode to run mode.) Press the DISPAY Key to return to Run mode from Setting mode.. Press the MODE Key to scroll successively through the items that can be set. Release the MODE Key to select the desired item. 1

15 Modes and Count Value Count CP1 Gate CP Count 1 Up (increment) mode A Inhibit 3 A 5 Count CP1 Gate CP Count n Down (decrement) mode A Inhibit n-1 n- n-3 A n- n-5 Gate CP1 Count CP Count 1 A Inhibit A 3 5 Gate CP1 Count CP Count n n-1 A Inhibit n- A n-3 n- n-5 Up/Down A Command mode Up/Down B Individual mode CP1 CP A A CP1 CP Count Count Up/Down C Phase difference mode BB BB Note 1 Note Note 3 A: Minimum signal width; B: Must be at least 1/ of minimum signal width. Signals may not be counted if the minimums for A and B are not met. Set the same counting speed for CP1 and CP when in Up/Down C mode. and Count Signal No-voltage Voltage Short circuit.5 to 3DC Open circuit to VDC 15

16 /Output Mode Setting -A/A/B/B/SA/SA/SB/SB/8/8/11/11 (N and R modes only apply to the -A and -SA types.) Output operation applies for 1-stage models only. Output mode mode Up Down Up/Down A.B.C N 999,999 Preset Preset 1 Output 1 F Output Outputs and present value display are maintained until reset. 999,999 Preset Preset 1 Output 1 C Output Present value display runs continuously. Outputs are maintained until reset. 999,999 Preset Preset 1 Output 1 R Output Present value is placed in reset start status as soon as count up is reached. The count up is not displayed. Outputs are 1-shot and operate repeatedly. Output 1 is self-holding, and goes off after expiration of the 1-shot period for Output. One-shot time periods for Output 1 and are independent. 999,999 Preset Preset 1 Output 1 Output Present value is placed in reset start status as soon as count up is reached. Outputs are 1-shot and operate repeatedly. Output 1 is self-holding, and goes off after expiration of the 1-shot period for Output. One-shot time periods for Output 1 and are independent. 1

17 Output mode mode Up Down Up/Down A.B.C K 999,999 Preset Preset 1 Output 1 P Output Present value runs continuously. Output 1 is self-holding, and goes off after expiration of the 1-shot period for Output. One-shot time periods for Output 1 and are independent. 999,999 Preset Preset 1 Output 1 Q Output Present value display does not change during 1-shot time period, but reset start status is returned to as soon as count is reached. Outputs are 1-shot and operate repeatedly. Output 1 is self-holding, and goes off after expiration of the 1-shot period for Output. One-shot time periods for Output 1 and are independent. 999,999 Preset Preset 1 Output 1 A Output Present value runs continuously through 1-shot time period and returns to reset start status immediately afterward. Outputs are 1-shot and operate repeatedly. Output 1 is self-holding, and goes off after expiration of the 1-shot period for Output. One-shot time periods for Output 1 and are independent. 999,999 Preset Preset 1 Output 1 Output Present value and output 1 maintain status until reset. Output 1 and operate independently. One-shot output from Output 1 Self-holding output One-shot output from Output Self-holding output One-shot outputs can be set to between 1 and 5 ms. 17

18 -C/SC Output operation applies for 1-stage models only. Output mode Operation after count mode Up/Down A.B.C up K Present value Compensation increments and decrements within 999,999 displayable range. Outputs go ON for one-shot. Compensation value Set Set 1-999,999 Output 1 D Output Compensation 999,999 Compensation value Set Set 1-999,999 Present value increments and decrements within displayable range. Outputs are ON during the count is equal. Output 1 Output Compensation 999,999 Compensation value Set Set 1-999,999 Present value increments and decrements within displayable range. Output 1 is ON whenever present value is less than or equal to Set 1; Output is ON whenever present value is greater than or equal to Set. Output 1 Output Compensation 999,999 Compensation value Set Set 1-999,999 Present value increments and decrements within displayable range. Output 1 is ON whenever present value is greater than or equal to Set 1; Output is ON whenever present value is greater than or equal to Set. Output 1 Output 18

19 Edge evel One-shot output Instantaneous (equals) output Self-holding output/level One-shot outputs can be set to between 1 and 5 ms. Note: 1. Counting s are not applied while the reset is ON.. One-shot outputs, when ON, are turned OFF when the reset goes ON. 3. One-shot outputs, when ON, are reset and the one-shot output is restarted if a preset designating the output is reached. 19

20 Dimensions Note: All units are in millimeters unless otherwise indicated. The dimensions are the same for both the -digit and -digit models. -A/B/C 8 1 M3.5 terminal screw (effective length: mm) Flash Mounting Adapter Panel Y9F-3 Flush Mounting Adapter min. Panel Cutouts Panel cutouts are as shown at right. (according to DIN37). min n side-by-side mounting A +1 A = (8n-.5) -S (Short Body) Note 1. The mounting panel thickness should be 1 to mm.. It is possible to mount Counters side by side, but one way only. M3.5 terminal screw (effective length: mm) -8/11

21 Flash Mounting Adapter -S Panel Y9F-3 Flush Mounting Adapter -8/11 Panel Y9F-3 Flush Mounting Adapter P3G-8 (P3GA-11) Flush Mounting Bracket Panel Cutouts Panel cutouts are as shown at right. (according to DIN37) min n side-by-side mounting min. A +1 A = (8n-.5) Note 1. The mounting panel thickness should be 1 to mm.. It is possible to mount Counters side by side, but only horizontally. -8/11 Mounting Styles Surface Mounting Flush Mounting Surface Mounting Flush Mounting Y9F-3 P3G Adaptor Y9F Adaptor P3GA-11 PCF PCF

22 Installation Terminal Arrangement Terminal arrangements for the -digit models are the same as those shown below. 1 Stage Contact Output -A -AV -A (Basic type) 1 Stage Contact Output -B(G) -BV(G) -C(G) -CV(G) -B (Standard type), -C (±Range type) Key protection Stage Contact Output -BW(G) -BWV(G) -CW(G) -CWV(G) Key protection or VDC 11 (+) ( ) Sensor power supply or VDC ( ) Sensor 11 power supply (+) OUT OUT to AC to AC (-) (+) 1 to AC/ VAC to VDC (-) (+) 1 to AC/ VAC to VDC VAC 1 Stage Transistor Output -AS -AVS 1 Stage Transistor Output -BS(G) -BVS(G) -CS(G) -CVS(G) Key protection Stage Transistor Output -BWS(G) -BWVS(G) -CWS(G) -CWVS(G) Key protection or VDC (+) ( ) Sensor power supply or VDC ( ) Sensor 11 power supply (+) OUT OUT to AC VAC to AC (-) (+) 1 to AC/ VAC to VDC (-) (+) 1 to AC/ VAC to VDC No-contact -8 (Standard type) Internal circuit Contact No-contact Contact ( ) /1 to VAC to VDC (+) 8 (-8S type) No-contact -11 (Standard type) Key protection Contact ( ) /1 to VAC to VDC (+) Internal circuit Contact 8 9 No-contact 11 (-11S type)

23 1 Stage Contact Output -SA -SA (Basic type) Stage Contact Output -SB -SC -SB (Standard type), -SC (±Range type) Key protection 11 OUT 11 OUT to VDC ( ) (+) ( ) (+) to VDC 1 Stage Transistor Output -SAS 1 Stage Transistor Output -SBS -SCS Key protection Stage Transistor Output -SBWS -SCWS Key protection OUT 11 OUT 11 OUT OUT ( ) (+) to VDC ( ) (+) to VDC ( ) (+) to VDC Note: Do not connect unused terminals. Connections The s of the are no-voltage (short circuit or open) s and voltage s. (Key protection only for no-voltage s) No-voltage s (With an External Power Supply) Open Collector Voltage Output Contact External power supply PC External power supply Note: The DC power supply must be 3DC max. igh: transistor ON igh: transistor ON igh: contact ON 3

24 No-voltage s (Without an External Power Supply) Open Collector PC Voltage Output Contact Note: The DC power supply must be 3DC max. igh: transistor ON igh: transistor ON igh: contact ON No-voltage Signal evels No-contact Contact 1. igh level Transistor ON Residual voltage: V max. Impedance when ON: 1 kω max.. ow level Transistor OFF Impedance when OFF: 1 kω max. Use contacts which can adequately switch ma at 5 V Voltage s (With an External Power Supply) NPN Transistor PNP Transistor Contact External power supply External power supply Note: The DC power supply must be 3DC max. igh: transistor OFF igh: transistor ON igh: contact ON

25 Voltage s (Without an External Power Supply) NPN Transistor PNP Transistor Contact Note: The DC power supply must be 3DC max. igh: transistor OFF igh: transistor ON igh: contact ON Voltage Signal evels 1. igh level.5 to 3DC. ow level to VDC Connection Examples with OMRON Sensors 3-wire DC type(npn) Photoelectric Output (black) Photoelectric sensor to V (brown) sensor E3S- A/B E3S-A/B (blue) 3-wire DC type (PNP) Output (black) to V (brown) (blue) (-) (-) (+) 11 Sensor power supply -B/BV (+) 11 Sensor power supply -BV *Models ending in -BV have reversed logic. Using the external power supply Photoelectric sensor E3S-A/B Output (black) to V (brown) Proximity sensor EE-X E Output (black) to V (brown) (blue) (blue) AV 11 -AV

26 Rotary Encoder Wiring Example Power supply Rotary encoder A phase B phase (-) (+) 11 -C 1 3 5

27 Precautions Sensor Power Supply The capacity of the external power supply is 1 ma at V/5 ma at V. When using a VAC/ to VDC power supply, reduce the load with the power supply voltage, as shown in the following diagram (DC power supplies only). oad current (ma) Supply voltage (VDC) VDC VDC Power Supplies When turning the power ON and OFF, signal reception is possible, unstable, or impossible as shown in the diagram below. The unstable period will vary with power supply voltage, and the load conditions on external power supplies. Power supply ON OFF to 5 ms 1 ms to.9 s impossible Possible impossible Unstable A switching regulator is used in the internal circuits of counters with 1-to--VAC or -to--vac specifications, causing an inrush current (approx. 1.5 A) to flow when power is turned on. If the capacity of the power supply to the counter is insufficient, the counter may not start operation. Be sure to provide adequate capacity (recommended supply capacity; : 15 W min. and -S: 5 W min.) Connect the power supply voltage through a relay or switch in such a way that the voltage reaches a fixed value immediately. Transistor Output The transistor output is insulated from the internal circuitry by a photocoupler, so either NPN or PNP output is possible. NPN output PNP output oad ( ) ( ) oad power supply oad ( ) ( ) oad power supply DIP Switch Setting Changes Any changes in the DIP switch settings while power is being supplied is invalid. Restart the power supply. Self-diagnostic Function The following displays will appear if an error occurs. The present value and output enter the same status as after pressing the RESET Key. Display Error Output status * ** Present value below min. Present value above max. No change Correction Press RESET Key or reset Function setting No change CPU OFF Press RESET Key Memory Set at the factory *Displayed when the present value has fallen below the min. value in the -C/SC (±range type). **Displayed when the present value has exceeded the max. value in the -C/SC (±range type). Operating Environment When using the Counter in an area with much electronic noise, separate the Timer, wiring, and the equipment which generates the signals as far as possible from the noise sources. It is also recommended to shield the signal wiring to prevent electronic interference. Organic solvents (such as paint thinner), as well as very acidic or basic solutions might damage the outer casing of the Counter. Using the Prescale Function When setting the prescale value, be sure that the set value satisfies this equation: set value max. value - prescale value. (if the prescale value is 1,5, ,5 = max.) If a higher value is used, the output may be affected, so make sure that the output is produced before starting operation. Changing Set Values When changing the set value while the Counter is operating, the output will be produced if the set value ever equals the present value. To avoid triggering the output, begin by incrementing a higher digit to a large number. ting with a Set Value of When resetting is performed with the set value set to, no output will be given for the safety reasons once the reset is turned OFF (except for the -C). Output Delay The following table shows the delay from when the present value passes the set value until the output is produced. (The delay is the result of output control time, signal transmission time, relay switching time, etc.) Actual measurements in N and K modes. Control output Max. counting Output delay* speed Contact output 1, 3 cps 18 to ms 1 kcps.7 to 5.8 ms 5 kcps. to 5. ms Transistor output 1, 3 cps 13.5 to ms 1 kcps.59 to.81 ms 5 kcps.9 to.ms 7

28 *The variation in delays is due to different modes and conditions. For systems where the delay is a problem, take actual measurements under operating conditions. Other When the Counter is installed in a control box and tests are conducted which may damage the Counter s internal circuitry (for example, a test measuring the maximum voltage difference between the control circuit and metal components), remove the Counter from the control box or short circuit the terminals.! Caution This product contains a lithium battery. ithium batteries explode if incinerated. Dispose of the Digital Counter as a noncombustible item. A DIMENSIONS SOWN ARE IN MIIMETERS. To convert millimeters into inches, multiply by To convert grams into ounces, multiply by.357. Cat. No. M-E1-1B OMRON Corporation Industrial Automation Company In the interest of product improvement, specifications are subject to change without notice. Measuring and Supervisory Controls Division 8th Fl., Crystal Tower Bldg., 1--7, Shiromi, Chuo-ku, Osaka 5-8 Japan Phone: (81) Fax: (81)-99-9 Printed in Japan 99-.5C (119) 8