DMS-30LCD Series. 3½ Digit, LCD Display Digital Panel Voltmeters. FEATURES

Transcription

1 DMS-0LCD Series ½ Digit, LCD Display Digital Panel Voltmeters FEATURES Large (0.4"/0.mm), enhanced-contrast, LCD display Single 5V supply or 9V battery Power as low as.mw Miniature size:." x 0.9" x 0.4" (55mm x mm x mm) Epoxy-encapsulated, -pin DIP Backlit displays optional 4 differential input voltage ranges High accuracy, ± count (±0.05%) Autopolarity changeover and overrange indication User-selectable decimal point placement Numerous "plug-on" application boards 0 to 0 C temperature range Offering all the outstanding features and benefi ts of DATEL s industry leading DMS- 0LCD Series of ½ Digit LCD Panel Meters, DMS-0LCD meters offer larger, more easily readable displays at slightly higher power consumptions. Like all DMS Series LCD meters, these miniature (. x 0.9 x 0.4 ), epoxy-encapsulated devices offer component-like ease-of-use, outstanding reliability and easy installation in either panels or pc-cards. DMS-0LCD devices operate from a single 5V supply or a 9V battery. Battery-operated units typically draw 50μA and consume a mere.mw. Backlit models are available for low-light applications; though we have found many designers prefer DATEL s unique low-power LED meters in those circumstances. Offering 4 optional input voltage ranges (±00mV, ±V, ±0V or ±00V), DMS-0LCD meters have an extremely user-friendly input structure. They can be used in differential or single-ended modes. Input impedance is a minimum 00kΩ. CMRR is typically db. CMV is ±V, and inputs are overvoltage protected to ±00V. Each meter incorporates an extremely stable, double regulated reference and is fully calibrated at our factory prior to encapsulation. We guarantee outstanding initial accuracy (± count) and excellent stability over temperature (±0.5 counts/ C). These extremely rugged meters are moisture and vibration proof and never require adjustment or recalibration. For popular applications (4-to-0mA, rms-to-dc conversion, ac line power, J and K thermocouples, etc.), the DMS-0LCD Series includes a complete line of "plug-on" application boards that conveniently convert your meter into an application-specifi c instrument. 5V SUPPLY/ BATTERY DISPLAY TEST/ BACKLIGHT 5V RETURN/ BATTERY 5V V () INPUT LO 5V 0.0μF DC/DC R () INPUT HI CONVERTER V 909k.0V J A/D 0 ANALOG 0 Vdc CONVERTER COMMON.V DATA REF. 4 9 DP.V REFERENCE OUT.k DP 5 REFERENCE OUT 5V DP REFERENCE IN is not used on ±00mV (-0) models or ±V (-) models. = 00k on ±0V (-) models and 9.k on ±00V (-) models. DC/DC converter is not used on 9V-powered models, J is connected. Display Test function is not available on backlit models. For full details go to 0 Jan 0 MPM_DMS0LCD.D0 Page of

2 Performance/Functional Specifications Typical at TA = 5 C and supply voltage = 5V (using the single-ended input circuit) or 9V (using the differential input circuit), unless otherwise noted. Analog Inputs Min. Typ. Max. Units Full Scale Input Range: DMS-0LCD-0 ±00 mv DMS-0LCD- ± Volts DMS-0LCD- ±0 Volts DMS-0LCD- ±00 Volts Input Impedence: DMS-0LCD-0, MΩ DMS-0LCD-, - 0. MΩ Overvoltage Protection ➀ DMS-0LCD-0, -, - ±00 Volts DMS-0LCD - ±50 Volts Common Mode Voltage Range ➁ ± Volts CMRR (dc to 0Hz) db Control Inputs ➂ Decimal Pt. Placement (Pins 4-): Functionality Logic Compatibility Display Test (Pin ) Backlight (Pin ) Performance Tie to pin to activate TTL (on 5V-powered models) Tie to pin to activate Tie to pin to turn on backlight Sampling Rate.5 reading per second Accuracy ( minute warm-up): DMS-0LCD-0 (Vin = 0.9V) ± ± Counts DMS-0LCD- (Vin =.9V) ± ± Counts DMS-0LCD- (Vin = 9V) ± ± Counts DMS-0LCD- (Vin = 90V) ± ± Counts Zero Reading (Vin = 0 Volts) Temperature Drift (0 = 0 C) ±0. ±0.4 Cnts/ C.V Reference Out (Pin 9).0..5 Volts Power Supply Requirements (5V Models) Supply Voltage Volts Supply Current: Standard Models μa Backlit Models 45 0 ma Power Supply Requirements (9V Models) Supply Voltage Volts Supply Current: Standard Models μa Backlit Models 45 0 ma Display Display Type and Size Polarity Indication Overrange Indication ½ digit, 0.4"/0.mm high LCD Autopolarity ("" for negative Vin) " _" for negative inputs " _" for positive inputs DMS-0LCD Series ½ Digit, LCD Display Digital Panel Voltmeters Physical/Environmental Operating Temperature 0 0 C Storage Temperature 0 5 C Humidity (non-condensing) 0 95 % Case Material Polycarbonate Weight 0.5 ounces ( grams) ➀ Applies for transient or continuous overvoltages applied to () INPUT HI (pin ) with () INPUT LO (pin ) properly connected. Pin is not overvoltage protected (see Figure ). Voltages applied to pin should not exceed the supply voltage. ➁ Listed spec applies to 5V-powered models only. For 9V-powered models, both () INPUT LO (pin ) and () INPUT HIGH (pin ) must always be at least.5v above BATTERY (pin ) and at least.5v below BATTERY (pin ). ➂ See Technical Notes. Ordering Information DMS-0LCD Input Range: 0 = ±00mV = ±V = ±0V = ±00V TECHNICAL NOTES Power Source: 5 = 5V 9 = 9V - C Accessories: DMS-0-CP Panel cutout punch DMS-BZL-C DMS-0 bezel assembly DMS-BZL-C DMS-0 bezel assembly with sealing gasket Add-On Application Boards: DMS-EB-C Multi-purpose (gain/offset, 4-0mA, etc.) DMS-EB-DC/DC-C Provides isolated 5V power DMS-EB-RMS-C For true rms measurements of ac voltages DMS-EB-AC/DC-C For ac line-powered applications A panel-mount retaining clip is supplied with each model. Add -C for RoHS Leave blank for standard models. Add B for backlit models...v REFERENCE OUTPUT (Pin 9): This pin is the output of the meter s precision.v internal reference, and it is referenced to ANALOG COMMON (pin 0) which sits at a potential of approximately V. This output should be buffered if used to drive external loads since sourcing more than 5μA from pin 9 can affect both the initial accuracy and temperature drift of the meter.. ANALOG COMMON (Pin 0): This pin is connected to an internal, low-noise, relative ground. It is used in certain differential and fl oating measurements as described in the Applications section of this data sheet and Ap Note of the DATEL Panel Meter Catalog. Pin 0 should not be connected to pin (5V RETURN/BATTERY) or to your system s analog ground. 0 Jan 0 MPM_DMS0LCD.D0 Page of

3 DMS-0LCD Series ½ Digit, LCD Display Digital Panel Voltmeters. Decimal Point Placement: The location of the decimal point is userselectable, and the decimal point control pins (DP-DP) are active low functions. Select the appropriate decimal point by tying the appropriate pin (pin 4, 5 or ) to pin (5V RETURN/ BATTERY). Unused decimal point location pins should be left open. For 5V-powered models, the decimal location pins are TTL compatible and may be hard wired as described above or driven with 5V TTL logic gates. 4. REFERENCE OUTPUT (Pin ) and INPUT (Pin ): Pin is a precision reference actively trimmed at the factory. In normal operation, pin must be tied to pin to achieve all listed accuracy and drift specifi cations. 5. DISPLAY TEST (Pin ): (Not available on backlit models) Connect DISPLAY TEST (pin ) to 5V SUPPLY/BATTERY (pin ) to activate. All LCD segments, exclusive of the decimal points, will be momentarily enabled. Do not leave the unit in the TEST mode for more than 0 seconds as this will damage the LCD segments.. BACKLIGHT (Pin ) Function: For backlit models, grounding pin (i.e. connecting it to pin ) turns on the backlighting LED s. 9V-powered backlit models function with supply voltages up to 4V, however, activating the backlight with voltages greater than 9.V can damage the meter. Therefore, a /4 Watt series resistor must be installed between pins and in these situations. The value of the series resistor is determined using the following formula: RSeries = Example: If BATTERY (pin with respect to pin ) is.v, RSeries = BATTERY 9.V V 0.05 RSeries = 9 Ohms Ohms Ohms. Soldering Methods: All models in the DMS-0LCD Series easily withstand most common wave soldering operations. We recommend, however, you evaluate the effects your particular soldering techniques may have on the meter s plastic case and high-precision electrical performance. We recommend the use of no-clean lead-free solders. 9. Suggested Mating Connectors: Panel mounted: Connector housing DATEL P/N Terminal type DATEL P/N Wire size to AWG Insulation diameter 0.0 (.5mm) maximum Stripping length 0.00 to 0.5 (.54 to.mm) Board mounted: Socket DATEL P/N APPLICATIONS DMS-0LCD meters are available in either 5V-powered or 9V-powered models. 9V devices operate directly from.5v to 4V supplies (usually batteries) without the need for external voltage regulators. 9V devices, however, can not be used to measure voltages referenced to the negative battery terminal (pin ) because the minus input to the meter (pin, () INPUT LO) must always be at least.5v above pin. 9V-powered meters can only be used to make differential and not single-ended measurements. 5V-powered devices operate from any well-regulated 5V supply and will accurately measure voltages both above and below pin (5V RETURN) in either single-ended or differential confi gurations.. Single-Ended Input Configurations: True single-ended measurements can only be made with 5V-powered meters. The circuit of Figure avoids problems normally associated with ground-loop currents. Separate ground runs should be used for 5V RETURN (pin ) and () INPUT LO (pin ). In any backlit application, including those with supply voltages < 9.V, the current drawn by the backlight (and therefore the current drawn by the meter) can be reduced by installing a /4 Watt resistor between pins and. The brightness of the backlight will be reduced proportionately.. Gain Adjust: There is a gain-adjust potentiometer on the back of each meter. It has approximately ±50 counts (±.5%) of adjustment range. Since these devices essentially have no zero/offset errors, a gain adjustment is effectively an overall accuracy adjustment. Though they may be performed at any point (except zero), accuracy adjustments are most effective when performed with higher level input signals. Refer to Figure 9 for applications requiring greater ( ±0%) gain adjustments. VIN 0 VAC 5V SUP DMS-0LCD--5 DP Figure. Single-Ended Input Configuration 5V RET 0 Jan 0 MPM_DMS0LCD.D0 Page of

4 DMS-0LCD Series ½ Digit, LCD Display Digital Panel Voltmeters APPLICATIONS. Differential Input Configurations: Differential measurements can be made with either 5V-powered or 9V-powered meters. Figure, though not a practical real-world application, uses a voltage divider to demonstrate the concept of a differential input signal. Be careful not to exceed the ±V common mode voltage limitation for 5V-powered meters. DP DMS-0LCD--5 5V SUP 5V RET R k k R k 4. Floating Signal Source Measurements: Floating signals can be measured using the circuits shown in Figures 5 and. Figure 5 uses a 5V-powered meter. Figure uses a 9V-powered meter. Connecting pin 0 (ANALOG COMMON) to () INPUT LO (pin ) provides the reference point for the meter s input. A fl oating input is a signal that has no galvanic connection to the meter s power supply. In the fi gures below, the.5v battery illustrates a true fl oating input..5v CELL 0 DMS-0LCD--5 5V SUP 5V RET DP 0 VAC 0 VAC Figure. Differential Input Configuration Figure 5. Floating Input Measurements. Engineering Scaling: For measuring voltages greater than the full scale input range of a given meter, the input signal must be attenuated. A simple voltage divider (similar to that shown in Figure 4) will scale the input to within the range of the selected meter. R and should be precision, ±%, metal-fi lm resistors with absolute TCR s less than 50ppm/ C. See Ap Note 4 for more information on engineering scaling..5v CELL 0 DMS-0LCD--9 50kΩ < R < 0MΩ x VIN = Reading R 9V BATTERY BAT BAT DP VIN R DMS-0LCD--5 Figure. Floating Input Measurements (9V-Powered Models) 0 VAC 5V SUP 5V RET 5. Process Control (4-to-0mA) Measurements: In many common process-control applications, a 4-to-0mA current loop is used to transmit information. Because DMS-0LCD meters have such high input impedance, a simple shunt resistor across the meter s input can be used to convert the loop current to a voltage. See Figure. The value of the shunt resistor is a function of the scaling requirements of the particular application and can be calculated using the following equation: Figure 4. Input Attenuation Circuit 0 Jan 0 MPM_DMS0LCD.D0 Page 4 of

5 DMS-0LCD Series ½ Digit, LCD Display Digital Panel Voltmeters APPLICATIONS RShunt = R = VFsr /IFsr Where: VFsr = Full scale reading (in Volts) I Fsr = Relative full scale current (in Amps) Example: For a meter with a V full scale input (.999 full scale reading) and a desired full scale display reading of 000 (with an input of 0mA), VFsr =.000 Volts RShunt =.000V/( )A RShunt =.000V/0.0A =.5 Ohms (R R) = 0. Therefore, the 9V battery voltage appears to the meter inputs as 0.9V. With the decimal point moved to its DP position (pin 5 tied to pin ), the meter reads 9.00 Volts. The circuit can be calibrated by fi rst measuring the actual battery voltage with another meter and then adjusting the gain-adjust potentiometer on the back of the DMS-0LCD until a similar reading is obtained. If possible, the resistors in the divider should be ±% metal-fi lm types with TCR s less than 50ppm/ C. To calibrate the circuit of Figure, perform the following:. With 4mA applied, adjust the 50kΩ potentiometer () to display a reading of "000" (assuming that is the desired reading).. With 0mA applied, adjust the gain-adjust potentiometer on the back of the meter to display a reading of "999". For different full scale readings, alter the RShunt value accordingly. BAT DMS-0LCD--9 BAT 5 DP R 45.k 0.k R 45.k DMS-0LCD--5 9V BATTERY 4-0mA R Figure. Power Supply Monitor (9V-Powered Models) 0 VAC 50k 5V SUP 5V RET Figure. 4-to-0mA Current Loop Operation. Power Supply Monitoring: A popular application for DATEL s lowpower LCD meters is monitoring the supply voltage in battery-operated portable equipment. Figure demonstrates how a 9V-powered DMS-0LCD can be used to monitor its own supply. The meter used is the DMS-0LCD--9. A three-resistor voltage divider is used to attenuate the battery voltage and also to satisfy the requirement that the input voltages applied to pins and be at least.5 Volts above and below the battery voltage applied to pins (BATTERY) and (BATTERY). The divider should be designed so that /0th the battery voltage falls across the inputs to the meter:. External Gain Adjustment: Connect REFERENCE OUT (pin ) to REFERENCE IN (pin ) for normal, factory calibrated, operation. Use the.v REFERENCE OUT (pin 9) for applications needing external gain adjustment. Figure 9 shows the wiring confi guration for each model. Calibration is performed with a precise, near-full-scale, input voltage. OUT VOLTAGE CALIBRATOR COM For 5V models tie to pin For 9V models tie to pin 0 5V RET 0 NC.45k, % DMS-0LCD k 0 to 0 Turns k 0 to 0 Turns.45k, % 9.V REF Connections for ±V and ±0V models Connections for ±00mV models Figure 9. External Gain Adjustment 0 Jan 0 MPM_DMS0LCD.D0 Page 5 of

6 DMS-0LCD Series ½ Digit, LCD Display Digital Panel Voltmeters MECHANICAL DIMENSIONS: Inches (mm) TOLERANCES: PL DEC ±0.0 (±0.5) PL DEC ±0.00 (±0.54) LEAD DIMENSIONS: 0.05 (0.5) x 0.05 (0.5) NOMINAL RECOMMENDED PC BOARD FINISHED HOLE DIAMETER: 0.04 ±0.00 (.0 ±0.0) CALIBRATION POTENTIOMETER HOLE LOCATION PIN # IDENTIFIER MADE IN USA DMS-0LCD-X-XX FRONT VIEW PIN 0.0 (.0) 5V SUPPLY/ BATTERY DISPLAY TEST/BACKLIGHT 5V RETURN/ BATTERY DP DP DP 4 5 () INPUT LO () INPUT HI 0 ANALOG COMMON 9.V REFERENCE OUT REFERENCE OUT REFERENCE IN 0.40 (.0) 0.5 (.5) DIAMETER (USE ONLY WHEN PC BOARD MOUNTING) 0.9 (.4) 0.4 (.) DP DP DP. (55.).09 (5.) (.0) 0.40 (0.9) STANDARD 0.50 (4.) BACKLIT 0.5 (.4) TYP (.0) 0. (4.) TYP (.) 0.0 (.5) TYP (.0).0 (45.) 0.5 (.) TYP. FRONT VIEW #-5 INSERT 0.5 (.9) DEEP 0. (4.5) BEZEL INSTALLATION.0 (.) PANEL MADE IN USA.55 (4.) RECOMMENDED DRILL AND PANEL CUTOUT DIMENSIONS 0. INTERNAL CORNER RADII: (.95) 0.0 (0.) MAX. BEZEL RETAINING CLIP INSTALLATION.0 (.) PANEL CUTOUT 0. (.0). (5.0) PANEL.5 (59.9) 0.09 (.) DIAMETER (4 REQUIRED) ONLY WHEN USING OPTIONAL BEZEL ASSEMBLY 0.09 (.44) Murata Power Solutions, Inc. Cabot Boulevard, Mansfi eld, MA U.S.A. ISO 900 and 400 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. 0 Murata Power Solutions, Inc. 0 Jan 0 MPM_DMS0LCD.D0 Page of