PROPRIETARY NOTICE. emview-19t/d. Embedded computer system. (User's Manual) Version 1.0. Preliminary. Refers to product revision no. V 1.

Size: px

Start display at page:

Download "PROPRIETARY NOTICE. emview-19t/d. Embedded computer system. (User's Manual) Version 1.0. Preliminary. Refers to product revision no. V 1."

Darren Wilkinson
5 years ago
Views:

1 emview-19t/d (User's Manual) Introduction 1-1 PROPRIETARY NOTICE All rights reserved by Janz Automationssysteme AG. No parts of this technical manual may be modified, copied or reproduced in any form or by any means for commercial use without the prior written permission of Janz Automationssysteme AG, Germany. All instructions, information and specification contained in this manual are for reference only and remain subject to change without announcement. emview-19t/d Embedded computer system (User's Manual) Version 1.0 Preliminary Refers to product revision no. V 1.0 Rev. 1.0 Janz Automationssysteme AG

$1-2 emview-19t/d (User's Manual) Introduction Title: emview-19t/d manual File: j:\as\entwicklung\projekte\hw\empc\emview\19_zoll\abgesetzt\doc\manual_emvi ew_19td.$

2 1-2 emview-19t/d (User's Manual) Introduction Title: emview-19t/d manual File: j:\as\entwicklung\projekte\hw\empc\emview\19_zoll\abgesetzt\doc\manual_emvi ew_19td.doc Pattern: j:\as\entwicklung\formulare\entwicklung (ew)\ew_manual.dot Created: ime, Last Update: ime, Figure 1: em[view]-19t/d front view Janz Automationssysteme AG 2009 Tel.: FAX: Internet: Janz Automationssysteme AG Rev. 1.0

3 emview-19t/d (User's Manual) Introduction 1-3 Contents 1 Introduction Features Functional Overview Installation Dimensions and mounting information Mounting Technical specification DC main power supply Serial interface - RS Universal serial bus - USB Analogue Video - VGA Digital video - DVI Display Driver installation Windows XP driver installation for touch-screen on USB Windows XP driver installation for touch-screen on RS Ubuntu Linux driver installation for touch-screen on RS232 or USB Use of em[view]-19t/d Using and calibrating the touch-screen on Windows XP Calibrating the touch-screen on Ubuntu Adjusting the display Technical Data 23 5 Product History Manual History Rev. 1.0 Janz Automationssysteme AG

4 1-4 emview-19t/d (User's Manual) Introduction List of Figures Figure 1: em[view]-19t/d front view...2 Figure 2: em[view]-19t/d side view...6 Figure 3: em[view] measures...7 Figure 4: Mounting em[view]-19t/d...8 Figure 5: Block diagram for the internal logic...9 Figure 6: Power connector...9 Figure 7: PenMount Control Panel Figure 8: Device 0 configuration Figure 9: Standard calibration screen List of Tables Table 1: em[view] dimensions...7 Table 3: Power connector assignment...9 Table 4: SUB-D 9 Pin assignment Table 5: Display specifications Table 6: Main menu Table 7: Input select menu Table 8: Brightness menu Table 9: Color settings menu Table 10: Image settings menu Table 11: Tools menu Some parts of the text are important. These are visually marked with the following signs: Indicates information that when not fully understood or followed, cause permanent damage to the system. You should not start using the product before you have read this information. Indicates information that we think you should have read to save your time by avoiding problems. Important suggestions that should be followed will also be marked with this sign. Acronyms and Abbreviations DVI ESD HMI LCD LVDS SVGA SXGA TFT USB UXGA VGA XGA Digital Visual Interface Electrostatic discharge Human Machine Interface Liquid Crystal Display Low Voltage Differential Signal, Video signal to the TFT display Super Video Graphic Array Super EXtended Graphics Array Thin Film Transistor Universal Serial Bus Ultra EXtended Graphics Array Video Graphic Adaptor, Video Graphic Array EXtended Graphics Array Janz Automationssysteme AG Rev. 1.0

5 emview-19t/d (User's Manual) Introduction Introduction Janz Automationssysteme AG s em[view] systems are an additional development. These HMI systems and industrial display solutions are a combination of the familiar Janz empc systems with a wide range of LCDs, with or without touch-screen. Starting from 6.4, the LCDs can be combined with empc-a400 or empc-m as a complete HMI solution with smallest dimensions and power dissipation. em[view]s are also available without touch-screen. The em[view]-19t/d is a display only solution. If a touch-screen is not needed contact Janz Automationssysteme AG for further information. 1.1 Features Touch screen linked by RS232 or USB Wake On Touch (with RS232, only) DVI and VGA connectors Small housing size V DC power supply Fanless cooling concept Protection rating of the front is IP65 Fast und easy mounting High grade aluminium front Customizable design of the front panel Very flat front panel design (only 4 mm) 1.2 Functional Overview em[view]s are normally delivered with a touch-screen. To use the touch-screen the em[view]-19t/d must be connected to a standard RS232 or USB port of a computer system e.g. an empc and a driver must be installed at the host. The control of the resistive touch-screen is realized through a PenMount DMC9000. The resistive touch-screen is realized through a 2.1mm thick glass panel with resistive surface. The PenMount controller is linked to the RS232 port and USB port. If the USB port is used, the serial port is deactivated. The power must be supplied by an external power supply. This power supply must be capable to provide enough power for the em[view]-19t/d. Please refer to the technical specifications section for more information. Rev. 1.0 Janz Automationssysteme AG

6 1-6 emview-19t/d (User's Manual) Introduction Figure 2: em[view]-19t/d side view Janz Automationssysteme AG Rev. 1.0

emview-19t/d (User's Manual) Installation 2-7 2 Installation When opening the shipping package of the em[view], the

The em[view] is delivered in a configured state, but the configurations can be adjusted by the user as well.

backside. The package also contains a terminal plug for the power connector.

The installation of this equipment is allowed for qualified service personnel only.

voltage. Auxiliary existing rules for installation of electrical equipment must be attended to. 2.

7 emview-19t/d (User's Manual) Installation Installation When opening the shipping package of the em[view], the contents of the package should be checked immediately. The em[view] is delivered in a configured state, but the configurations can be adjusted by the user as well. To adjust the em[view]s configuration, an OSD (On Screen Display) is installed and controllable by buttons at the backside. The package also contains a terminal plug for the power connector. The em[view] needs a power source in between 14 to 30V DC for operation. The installation of this equipment is allowed for qualified service personnel only. Before connecting the DC main supply, the protective bonding conductor (PE) must be attached to prevent hazardous voltage. Auxiliary existing rules for installation of electrical equipment must be attended to. 2.1 Dimensions and mounting information E B D C A Figure 3: em[view] measures The needed cut-out measures are given by A and B. The overall front panel dimensions are denoted with C and D. E is the depth of the case. Display A B C D E /+2 mm 365-0/+2 mm 460 mm 386 mm 52 mm Table 1: em[view] dimensions Rev. 1.0 Janz Automationssysteme AG

Special mounting clamps fix the display without drilling extra holes; the mounting screws are not visible from the front side.

8 2-8 emview-19t/d (User's Manual) Installation The maximum thickness of the front, where the em[view] is mounted in must not exceed 8 mm. 2.2 Mounting The em[view] is designed to be mounted into a front panel. Special mounting clamps fix the display without drilling extra holes; the mounting screws are not visible from the front side. Please refer to the dimension specifications Table 1 for the necessary front panel cut-outs. hook in clamp, screw to fixate. Figure 4: Mounting em[view]-19t/d Janz Automationssysteme AG Rev. 1.0

emview-19t/d (User's Manual) Installation 2-9 Excessive fasten the mounting brackets leads to a malfunction of the touch screen. 2.3 Technical specification The em[view]-19t/d has five connectors, the main power supply, a serial interface and USB connector, VGA and DVI-D connector.

9 emview-19t/d (User's Manual) Installation 2-9 Excessive fasten the mounting brackets leads to a malfunction of the touch screen. 2.3 Technical specification The em[view]-19t/d has five connectors, the main power supply, a serial interface and USB connector, VGA and DVI-D connector. Figure 5 shows a block diagram of the internal function. VGA DVI-D Scaler unit Power Power unit Display with touch-screen USB RS232 Interface unit Figure 5: Block diagram for the internal logic DC main power supply The Power unit (Figure 5) is energizing all internal components, the display and its backlight. Thereby the power supply can vary in between 14 to 32 VDC. Before connecting the DC main power supply the protective bonding conductor (PE) must be connected. The power connector is included in delivery. The assignment of this connector is shown in Figure 6 and Table Pin Description VDC 2 NC, do not connect 3 GND Figure 6: Power connector Table 2: Power connector assignment Serial interface - RS232 The em[view]-19t/d provides a serial interface to connect the touch-screen to a host computer. If the USB is connected to the host the serial interface chip is deactivated. The pin assignment of the 9 pin female SUB-D connector is shown in Table 3. Rev. 1.0 Janz Automationssysteme AG

10 2-10 emview-19t/d (User's Manual) Installation Pin Assignment Output 1 NC 2 TxD 3 RxD 4 NC 5 GND 6 NC 7 RTS 8 NC 9 RI Table 3: SUB-D 9 Pin assignment The em[view]-19t/d provides a ring indicator (RI) signal for waking up the host PC. To use this feature the host must provide Wake On Ring (also PowerUp on Modem ) and this option must be activated in the BIOS. The length of serial cable must not exceed 10 m Universal serial bus - USB To connect the touch-screen to a host computer the USB can be used, too. The connector is USB Type B, so a standard USB Type A to Type B cable can be used to connect the touch-screen with the host. The length of USB cable must not exceed 5 m Analogue Video - VGA There are two ways to apply video data. One of them is an analogue video signal over the VGA connector (High density 15 pin female SUB-D). Analogue resolutions to SXGA (1280x1024) at 75 MHz or UXGA (1600x1200) at 60 MHz are support. A 10 m VGA cable is tested with the em[view]-19t/d Digital video - DVI As noticed earlier there is a second way to apply video data, the digital input DVI. The reliable DVI port is operating up to 165 MHz (UXGA at 60 MHz), thus it can be connected to all compliant digital DVI transmitters. The length of the DVI-D cable must not exceed 10 m. The best picture results are obtained by setting the native resolution. The native resolution of the display is 1280 x 1024 (SXGA) Display The panel is build as a thin film transistor liquid crystal display TFT-LCD with a diagonal screen of 19 and up to 16M colours. Janz Automationssysteme AG Rev. 1.0

emview-19t/d (User's Manual) Installation 2-11 Description Specification Display area 376.32 x 301.06 mm Number of dots 1280x3 (H) x 1024 (V) (RGB vertical stripe) Pixel Pitch 0.294 (H) x 0.

11 emview-19t/d (User's Manual) Installation 2-11 Description Specification Display area x mm Number of dots 1280x3 (H) x 1024 (V) (RGB vertical stripe) Pixel Pitch (H) x (V) Brightness 270 (Cd/m²) Contrast ration Typ. 800:1 Viewing angles -89 to 89 (H), -89 to 89 (V) Backlight 4 x CCFL Table 4: Display specifications 2.4 Driver installation Depending on using USB or serial interface, one or two drivers have to be installed. If the em[view] is delivered without touch-screen there are no drivers needed. Using the serial interface only the PenMount DMC 9000 driver has to be installed. Is the USB interface used, the PenMount driver must be installed as well and an auxiliary driver for the USB transceiver chip FT-232R with virtual COM port (VCP) must be installed. A Linux kernel (newer than version ) contains the VCP driver. Both drivers are receivable for several operating systems, visit the driver developer homepages: FTDI: PenMount: Windows XP driver installation for touch-screen on USB At first the USB virtual com port driver has to be downloaded, after that it must be installed. When plugging in the USB cable Windows notifies that new hardware is found. Don t search for Windows updates when asked (No, not this time). Now the driver must be installed from the location it is saved after download. Rev. 1.0 Janz Automationssysteme AG

$c:\temp\ftdi.$ Windows searches the driver for the FTDI chip at the specified location.

12 2-12 emview-19t/d (User's Manual) Installation On this example it is saved on c:\temp\ftdi. Windows searches the driver for the FTDI chip at the specified location. When asked for continuing the installation even though the driver has not passed the Windows logo test, Continue Anyway. Janz Automationssysteme AG Rev. 1.0

Now the USB virtual COM port driver is installed and Windows notifies that it has found

13 emview-19t/d (User's Manual) Installation 2-13 After continuing the installation it is finish by confirming the Finish-Button. Now the USB virtual COM port driver is installed and Windows notifies that it has found another new hardware. The next section describes how to install the PenMount driver for the touch-screen. Rev. 1.0 Janz Automationssysteme AG

2-14 emview-19t/d (User's Manual) Installation 2.4.2 Windows XP driver installation for touch-screen on RS232 If the

has to be installed. It can be downloaded at the address above.

14 2-14 emview-19t/d (User's Manual) Installation Windows XP driver installation for touch-screen on RS232 If the touch-screen is connected on the RS232 connector or the USB virtual COM port driver is installed the PenMount driver has to be installed. It can be downloaded at the address above. The driver installation is started by clicking the Setup executable in the PenMount folder. The license agreement must be confirmed. Janz Automationssysteme AG Rev. 1.0

15 emview-19t/d (User's Manual) Installation 2-15 The location where the driver will be installed to must be chosen. After choosing the location the driver will be installed and the device is searched. Rev. 1.0 Janz Automationssysteme AG

16 2-16 emview-19t/d (User's Manual) Installation Is the device found the installation is finished by clicking Finish. Janz Automationssysteme AG Rev. 1.0

17 emview-19t/d (User's Manual) Installation Ubuntu Linux driver installation for touch-screen on RS232 or USB Download the correct driver for the installed OS. In this section the installation on an Ubuntu 8.04 is shown. Once the driver is downloaded (Ubuntu 8.04 Driver 2.2) the archive has to be unzipped somewhere with: gunzip PenMount Ubuntu8.04 Driver V2.2.tar.gz and tar -xvf PenMount Ubuntu8.04 Driver V2.2.tar. After unzipping the archive a folder pmlinux-ubuntu8.04 remains. Jumping into it with cd pmlinux-ubuntu8.04 and installing the driver with sudo./pm-setup. Choosing the model 4 (PenMount 9000). Now the difference is coming, when installing the touchscreen with RS232 choose the correct device (e.g. /dev/ttys0 while using COM1). When the touchscreen is connected to USB choose 5 for other serial devices and type in /dev/ttyusb0. This is the device where the FTDI driver mounts the found chip to. Baud rate 19200, right button, stream mode, 500 (for 500 ms hold time) and the driver is installed. Now restart the xserver (Ctrl + Alt + Backspace). Rev. 1.0 Janz Automationssysteme AG

1 Using and calibrating the touch-screen on Windows XP Once the drivers are installed, the PenMount monitor icon is shown in the taskbar.

18 3-18 emview-19t/d (User's Manual) Use of em[view]-19t/d 3 Use of em[view]-19t/d Once the em[view] is installed it can be used at once, it is already configured. The user is free to adjust the configuration at will. To do so, the installed on screen display (OSD) must be used. To finish the driver installation, the touch screen must be calibrated. 3.1 Using and calibrating the touch-screen on Windows XP Once the drivers are installed, the PenMount monitor icon is shown in the taskbar. By clicking the icon the control panel is started and the touch screen configuration is displayed as shown in Figure 7. There are four tabs in the control panel, Device, Multiple Monitors, Tools and About. On the device tab a field with found device is shown. By selecting one of these devices it can be configured. While using more than one monitor with touch-screen the Multiple Monitors tab helps to map the touchscreens at will. The Tools tab shows miscellaneous small tools for working with the touch-screen and at least the About tab shows version information for the control panel. Figure 7: PenMount Control Panel The device window displays the detected devices, in case of Figure 7 there is only one device installed. By double clicking this device (PenMount 9000 RS232) another window (Figure 8) is shown. Figure 8: Device 0 configuration Janz Automationssysteme AG Rev. 1.0

19 emview-19t/d (User's Manual) Use of em[view]-19t/d 3-19 On this window the settings for Device 0 are accessible. As seen in Figure 8 there are three tabs to configure the touch-screen. The first is for calibrating the device, the second shows settings like touch-mode, cursor stabilization and right click characteristic. To calibrate the touch-screen the button Standard Calibration must be activated and the following screen appears Figure 9: Standard calibration screen Further steps are displayed. After hitting all the red squares the calibration is done and the touchscreen is operational. Note: The shown example is for calibrating the touch-screen on Windows XP system, on other Microsoft operating systems or Linux it is similar. 3.2 Calibrating the touch-screen on Ubuntu 8.04 The function of the touch-screen can be checked by looking into the device with cat /dev/ttys0 or cat /dev/ttyusb0 The console gives out some characters while touching the touch-screen. The calibration program is started with sudo gcalib. Sometimes it is necessary to jump into the folder, where the installation files for the PenMount driver are to start gcalib. Rev. 1.0 Janz Automationssysteme AG

20 3-20 emview-19t/d (User's Manual) Use of em[view]-19t/d The calibration screen is looking like that. The calibration is finished by clicking the red squares. Janz Automationssysteme AG Rev. 1.0

emview-19t/d (User's Manual) Use of em[view]-19t/d 3-21 3.3 Adjusting the display On the backside of the em[view]-19t/d there are five buttons.

21 emview-19t/d (User's Manual) Use of em[view]-19t/d Adjusting the display On the backside of the em[view]-19t/d there are five buttons. The first button is On/Off, it controls the backlight and display controller. The serial interface and the USB interface are kept alive. Second is the OSD button, it activates the OSD menu. Third is a confirm button to save and exit the OSD menu. The two others (Up/Down) are to navigate within the OSD menu. Once the OSD Button is activated, the OSD is displayed. The main menu has six tabs Main menu Input select Brightness Color settings Image settings Tools Exit This menu item is the default tab and the input VGA or DVI is selectable. Note: These items are selectable only if there is a signal source at every connector. This menu item shows four submenu items to control the brightness, contrast, backlight and one for stepping up to the main menu This menu controls the colour settings; to adjust the colours the wizard is used. Secondary the colour temperature is adjustable. Note: If using the DVI input the wizard is disabled. This menu controls the position of the image. It contains a wizard, the width, phase, horizontal and vertical position and exit. Note: This item is accessible with the VGA input only. This menu contains tools for controlling the OSD, sharpness and overlapped mode and a factory, color and position reset are possible. To exit the OSD. Table 5: Main menu Input select menu DVI Selects the digital input, if a digital signal source is connected. VGA Selects the analogue input, if a analogue signal source is connected Exit To exit this menu. Table 6: Input select menu Brightness menu Brightness Contrast Backlight Exit Adjusts the brightness of the display with buttons Up/Down. Adjusts the contrast of display with buttons Up/Down. Adjusts the backlight of display with buttons Up/Down. To exit this menu. Table 7: Brightness menu Color settings menu Wizard Auto adjusts the colours. Color temperatur Different colour temperature profiles. Exit To exit this menu. Table 8: Color settings menu Rev. 1.0 Janz Automationssysteme AG

22 3-22 emview-19t/d (User's Manual) Use of em[view]-19t/d Image settings menu Wizard Auto adjusts the position of the Image. Width Adjusts width of the image. Phase Adjusts the sample phase of analogue signal. H-Position Horizontal position of the image. V-Position Vertical position of the image. Exit To exit this menu. Table 9: Image settings menu Tools menu OSD Factory reset Factory color reset Factory position reset Sharpness Overlapped mode Exit Auto adjusts the position of the Image. Resets to factory defaults. Resets the color settings to factory defaults. Resets the position to factory defaults. Selects the level of sharpness. Selects the overlapped mode To exit this menu. Table 10: Tools menu Janz Automationssysteme AG Rev. 1.0

23 emview-19t/d (User's Manual) Technical Data Technical Data Interfaces USB Serial Port RS232 VGA DVI The USB port is for connecting the touch screen with a computer system. Thereby the serial port is tunnelled through USB virtual COM port. The serial port connects the touch controller with a computer system. It is possible to wake up the computer system by touching the screen. This is realized by the Ring Indicator (RI) signal with in the serial port. Source signal which appears on the screen. Max. Resolution SXGA (1280x1024) at 75 MHz or UXGA (1600x1200) at 60 MHz. It is recommended, that the native resolution of the display is used. Source signal which appears on the screen. Resolution up to 165 MHz (UXGA at 60 MHz). It is recommended, that the native resolution of the display is used. Display Area x mm Number of dots 1280 x 3 (H) x 1024 (V) (RGB vertical stripe) Pixel Pitch (H) x (V) Brightness 270 (Cd/m²) Contrast ration Typ. 800:1 Viewing angles -89 to 89 (H), -89 to 89 (V) Power Supply Input consumption Housing Height Width Depth Weight Needed cut-out Protection rating V DC tbd 460 mm 365 mm 51.8 mm tbd 440 x 365 mm IP65 Environmental Specifications (assembled system) Temperature range C (operating), (non operating) Humidity 0%..80%, non condensing Rev. 1.0 Janz Automationssysteme AG

24 5-24 emview-19t/d (User's Manual) Product History 5 Product History Note that changes in the major version number are related to a PCB redesign. Though, PCB redesign need not be related to functional changes, but might have been done for manufacturing purposes only. Version Release Date V Name Changes ime, tme initial version 5.1 Manual History Version Release Date Name Changes V ime Initial document for the Prototyp. Janz Automationssysteme AG Rev. 1.0

TPM Applications. Features. Optional Items. Packing List. Ordering Information. Industrial 10.4 LED Projected Capacitive Multi-touch Display

TPM Applications. Features. Optional Items. Packing List. Ordering Information. Industrial 10.4 LED Projected Capacitive Multi-touch Display TPM-3210 Industrial 10.4 LED Projected Capacitive Multi-touch Features 10.4 LED SVGA LCD Panel up to 800 x 600 Resolution 5-wire Resistive / Projected Capacitive Touch Technology 12-24 V DC Power Input