Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Transcription

1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED LEASING/MONTHLY RENTALS ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center SM InstraView REMOTE INSPECTION Remotely inspect equipment before purchasing with our interactive website at Contact us: (888) 88-SOURCE WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-backs and trade-ins LOOKING FOR MORE INFORMATION? Visit us on the web at for more information on price quotations, drivers, technical specifications, manuals, and documentation

2 NI Serial Hardware Specifications and Features Guide Contents This document lists safety and compliance information for NI Serial hardware, as well as physical specifications, software features, and recommended operating conditions. Supported Interfaces and Operating Systems... 2 NI-Serial for Windows and LabVIEW Real-Time Supported Interfaces... 2 NI-Serial Hardware Operating System Support... 5 Serial Hardware Features... 6 Connectors and Pinouts... 7 DB-9 Male... 7 DB-25 Male Position Modular Jack (0P0C) Pin Connector... 0 Cables and Accessories... 2 RS-232, RS-422, and RS RS-232, RS-422, and RS-485 Features... 3 RS-232 Loopback... 3 RS-232 Signals... 3 RS-485/422 Loopback... 4 RS-485/422 Signals... 4 RS-485 Topologies... 4 RS-485 Transceiver Control... 5 UART Data Frame Example... 5 Hardware Specifications... 5 NI 9870 RS-232 C-Series Module... 5 NI 987 RS-485 C-Series Module... 8 PCI Serial Hardware... 2 PCI Express Serial Hardware PXI Serial Hardware USB Serial Hardware ENET Serial Hardware ExpressCard Serial Hardware PCMCIA Serial Hardware... 5 Where to Go for Support... 54

3 Supported Interfaces and Operating Systems Hardware Interface PCI/ PCI Express Windows 7 32-Bit Table. Supported Interfaces and Operating Systems Windows 7 64-Bit Windows Vista 32-Bit Windows Vista 64-Bit Windows XP 32-Bit/2000 LabVIEW Real-Time PXI USB ENET ExpressCard PCMCIA 3 3 PCI only. 2 NI-VISA support only. 3 Supported by NI-Serial versions and earlier. NI-Serial for Windows and LabVIEW Real-Time Supported Interfaces Table 2. PCI Interfaces PCI Interfaces Standard # Ports Isolated Max Baud (kbits/s) 3 Connector Type 2 FIFO Size (Bytes) PCI-8430/2 RS No DB-9 male 28 PCI-8430/4 RS No P0C 28 PCI-8430/8 RS No pin SCSI 28 PCI-8430/6 RS No pin VHDCI 28 PCI-843/2 RS-485/RS No DB-9 male 28 PCI-843/4 RS-485/RS No P0C 28 PCI-843/8 RS-485/RS No pin SCSI 28 PCI-8432/2 RS Yes DB-9 male 28 PCI-8432/4 RS Yes P0C 28 PCI-8433/2 RS-485/RS Yes DB-9 male 28 PCI-8433/4 RS-485/RS Yes P0C 28 The two-wire auto control mode for RS-485 transceiver control has a maximum baud rate of 2000 kbits/s. 2 Serial connector cables end in DB-9 male serial connectors. 3 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. NI Serial Hardware Specifications and Features Guide 2 ni.com

4 Table 3. PCI Express Interfaces PCI Express Interfaces Standard # Ports Isolated Max Baud (kbits/s) 3 Connector Type 2 FIFO Size (Bytes) NI PCIe-8430/8 RS No pin VHDCI 28 NI PCIe-8430/6 RS No pin VHDCI 28 NI PCIe-843/8 RS-485/RS No pin VHDCI 28 NI PCIe-843/6 RS-485/RS No pin VHDCI 28 The two-wire auto control mode for RS-485 transceiver control has a maximum baud rate of 2000 kbits/s. 2 Serial connector cables end in DB-9 male serial connectors. 3 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. Table 4. PXI Interfaces PXI Interfaces Standard # Ports Isolated Max Baud (kbits/s) 3 Connector Type 2 FIFO Size (Bytes) PXI-8430/2 RS No DB-9 male 28 PXI-8430/4 RS No P0C 28 PXI-8430/8 RS No pin SCSI 28 PXI-8430/6 RS No pin VHDCI 28 PXI-843/2 RS-485/RS No DB-9 male 28 PXI-843/4 RS-485/RS No P0C 28 PXI-843/8 RS-485/RS No pin SCSI 28 PXI-8432/2 RS Yes DB-9 male 28 PXI-8432/4 RS Yes P0C 28 PXI-8433/2 RS-485/RS Yes DB-9 male 28 PXI-8433/4 RS-485/RS Yes P0C 28 The two-wire auto control mode for RS-485 transceiver control has a maximum baud rate of 2000 kbits/s. 2 Serial connector cables end in DB-9 male serial connectors. 3 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. National Instruments Corporation 3 NI Serial Hardware Specifications and Features Guide

5 Table 5. USB Interfaces USB Interfaces Standard # Ports Isolated Max Baud (kbits/s) Connector Type FIFO Size (Bytes) USB-232 RS-232 No DB-9 male 28 USB-232/2 RS No DB-9 male 28 USB-232/4 RS No DB-9 male 28 USB-485 RS-485/RS-422 No DB-9 male 28 USB-485/2 RS-485/RS No DB-9 male 28 USB-485/4 RS-485/RS No DB-9 male 28 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. Table 6. ENET Interfaces ENET Interfaces Standard # Ports Isolated Max Baud (kbits/s) Connector Type FIFO Size (Bytes) ENET-232/2 RS No DB-9 male 28 ENET-232/4 RS No DB-9 male 28 ENET-485/2 RS-485/RS No DB-9 male 28 ENET-485/4 RS-485/RS No DB-9 male 28 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. Table 7. PCMCIA Interfaces PCMCIA Interfaces Standard Isolated Max Baud (kbits/s) Connector Type FIFO Size (Bytes) PCMCIA-232 RS-232 No 92.6 DB-9 male 6 PCMCIA-232/2 RS-232 No 92.6 DB-9 male 6 PCMCIA-232/4 RS-232 No 5.2 DB-9 male 64 PCMCIA-485 RS-485/RS-422 No 92.6 DB-9 male 6 PCMCIA-485/2 RS-485/RS-422 No 92.6 DB-9 male 6 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. NI Serial Hardware Specifications and Features Guide 4 ni.com

6 Table 8. ExpressCard Interfaces ExpressCard Interfaces Standard # Ports Isolated Max Baud (kbits/s) Connector Type FIFO Size (Bytes) NI ExpressCard-8420/2 RS No DB-9 male 28 NI ExpressCard-842/2 RS-485/RS No DB-9 male 28 All NI serial hardware supports standard baud rates. In addition, the PCI/NI PCIe/PXI-843x family of hardware supports any baud rate between 2 bits/s and the maximum supported baud rate for that interface. All baud rates are supported because the UART can get within.3 percent of all baud rates in that range. National Instruments considers the following baud rates to be standard. NI serial hardware supports these rates up to the maximum rate specified. Your device may also support additional baud rates not listed below: To set the baud rate, set the VISA Baud attribute or use the Windows SetCommState function and pass the actual value of the baud rate in the BaudRate field of the DCB structure. Refer to Hardware Specifications for supported baud rates on each board. NI-Serial Hardware Operating System Support Refer to the following table for operating system support for NI serial hardware. Table 9. NI-Serial Hardware Operating System Support Bus Windows 7 32 Windows 7 64 Windows Vista 32 Windows Vista 64 Windows XP/2000 Linux x86 LabVIEW Real-Time Mac OS X PCI/ NI PCIe-843x 3 PXI-843x 3 USB ENET ExpressCard PCMCIA 2 2 NI-VISA support Native OS support (COM port with NI-Serial driver) PCI only. 2 Supported with NI-Serial and earlier. 3 With Linux kernel and later (RS-232 only), including 64-bit Linux. National Instruments Corporation 5 NI Serial Hardware Specifications and Features Guide

7 Serial Hardware Features Hardware PCI/NI PCIe/ PXI-8430, PCI/PXI-8432 PCI/NI PCIe/ PXI-843 eight port and NI PCIe port All other PCI/PXI-843 and PCI/PXI-8433 Adjustable FIFO Settings To determine which features your product supports, refer to the following table. Get Interface Type Table 0. Serial Hardware Features RS-485 Transceiver Control RS-485 Socketed Bias Resistors RS-485 Programmatically Controlled Bias Resistors RS-232 Transceiver State RS-232 DTE/DCE Transceiver Control Hardware Implemented Flow Control RTS/ CTS DTR/ DSR USB-232 one port USB-232 two and four port USB-485 one port USB-485 two and four port ENET-232 ENET-485 NI ExpressCard-8420 NI ExpressCard-842 PCMCIA-232 PCMCIA-485 Xon/ Xoff NI Serial Hardware Specifications and Features Guide 6 ni.com

8 Connectors and Pinouts DB-9 Male Pin Pin 6 Pin 5 Pin 9 Figure. DB-9 Connector Pin Locations Table. DB-9 Male Pin Descriptions Pin 232 DTE 232 DCE 422/485 DCD DCD GND 2 RXD TXD CTS+ (HSI+) 3 TXD RXD RTS+ (HSO+) 4 DTR DSR RXD+ 5 GND GND RXD 6 DSR DTR CTS (HSI ) 7 RTS CTS RTS (HSO ) 8 CTS RTS TXD+ 9 RI RI TXD These signals are No Connect on the PCI-232I and PXI-8422 ports and ports 9 6 on legacy 6-port boards. Note DCE mode supported on USB-232/2 and USB-232/4 only. National Instruments Corporation 7 NI Serial Hardware Specifications and Features Guide

9 DB-25 Male Pin Pin 3 Pin 4 Pin 25 Figure 2. DB-25 Connector Pin Locations Table 2. DB-25 Pin Descriptions Pin /485 2 TXD RTS+ (HSO+) 3 RXD CTS+ (HSI+) 4 RTS RTS (HSO ) 5 CTS TXD+ 6 DSR CTS (HSI ) 7 GND RXD 8 DCD GND 20 DTR RXD+ 22 RI TXD These signals are No Connect on the PCI-232I and PXI-8422 ports. Note Pins not listed in this table are No Connect. NI Serial Hardware Specifications and Features Guide 8 ni.com

10 0-Position Modular Jack (0P0C) Pin Pin 0 Figure 3. 0-Position Modular Jack Pin Locations Table 3. 0-Position Modular Jack Pin Descriptions Pin /485 No Connect No Connect 2 RI TXD 3 CTS TXD+ 4 RTS RTS (HSO ) 5 DSR CTS (HSI ) 6 GND RXD 7 DTR RXD+ 8 TXD RTS+ (HSO+) 9 RXD CTS+ (HSI+) 0 DCD GND These signals are No Connect on the PCI-232I and PXI-8422 ports. National Instruments Corporation 9 NI Serial Hardware Specifications and Features Guide

11 68-Pin Connector The following figures and table give the 68-pin connector pin locations and descriptions. The SCSI 68-pin connector and VHDCI 68-pin connector have the same pinout. PIN 68 PIN 34 PIN 35 PIN Figure Pin SCSI Connector Pin Locations NI Serial Hardware Specifications and Features Guide 0 ni.com

12 PIN 35 PIN PIN 68 PIN 34 Figure Pin VHDCI Connector Pin Locations Table Pin Connector Pin Descriptions 68-Pin Connector Port Signal 485 D-Sub 9 Connector 232 Signal 232 D-Sub 9 Connector RXD 5 DCD CTS+ 2 RXD RTS+ 3 TXD RXD+ 4 DTR GND GND CTS 6 DSR RTS 7 RTS TXD+ 8 CTS TXD 9 RI 9 National Instruments Corporation NI Serial Hardware Specifications and Features Guide

13 Cables and Accessories Part Number The following serial cables and accessories are available from National Instruments. Refer to ni.com for more information. Table 5. Serial Cables and Accessories Description Adapter Cables (DB-9 and DB-25 connectors have jacksockets unless otherwise specified.) DB-9 RS485 terminating pass-through connector 20 Ω Serial cable, 0P0C modular plug to DB-9 male, m Serial cable, 0P0C modular plug to DB-9 male, 2 m Serial cable, 0P0C modular plug to DB-9 male, 3 m Serial cable, 0P0C modular plug to DB-25 male, m Serial cable, 0P0C modular plug to DB-9 male, m, isolated Serial cable, 0P0C to DB-9 male, jackscrews, 2 m Serial cable, PCMCIA-232/485 to DB-9 male, m R3 Serial cable, PCMCIA-232/485 to DB-9 male, 0.3 m Serial cable, 68-pin VHDCI to eight DB-9 male, RS-232, m Serial cable, 68-pin VHDCI to eight DB-9 male, RS-485, m Extension and Null-Modem Cables (All cables have jackscrews.) Serial cable, RS232 null modem, DB-9 female to DB-9 female, m Serial cable, RS232 null modem, DB-9 female to DB-9 female, 2 m Serial cable, RS232 null modem, DB-9 female to DB-9 female, 4 m Serial cable, RS232 straight through, DB-9 female to DB-9 female, m Serial cable, RS232 straight through, DB-9 female to DB-9 female, 2 m Serial cable, RS232 straight through, DB-9 female to DB-9 female, 4 m Serial cable, RS485/RS422 null modem, DB-9 female to DB-9 female, m Serial cable, RS485/RS422 null modem, DB-9 female to DB-9 female, 2 m Serial cable, RS485/RS422 null modem, DB-9 female to DB-9 female, 4 m NI Serial Hardware Specifications and Features Guide 2 ni.com

14 RS-232, RS-422, and RS-485 RS-232, RS-422, and RS-485 Features Table 6. RS-232, RS-422, and RS-485 Features Feature RS-232 RS-422 RS-485 Type of transmission lines Single ended Differential Differential Maximum number of drivers 32 Maximum number of receivers 0 32 Maximum cable length 2500 pf equivalent 4,000 ft 4,000 ft Maximum CMV ± 25 V ±7 V +2 to 7 V Driver output 5 to 25 V 2 to 6 V.5 to 6 V Driver load <3 kω 00 Ω 60 Ω Actual driver output varies depending on cable length and load. RS-232 Loopback Pin Pin 6 TX/RX Pin 5 Pin 9 Pin Pin 6 All Pin 5 Pin 9 Figure 6. RS-232 Loopback RS-232 Signals 25 V 3 V 3 V 25 V SPACE, '0' UNKNOWN MARK, '' Figure 7. RS-232 Signals National Instruments Corporation 3 NI Serial Hardware Specifications and Features Guide

15 RS-485/422 Loopback Pin Pin 6 TX/RX Pin 5 Pin 9 Pin Pin 6 All Pin 5 Pin 9 Figure 8. RS-485/422 Loopback RS-485/422 Signals If ' ' < '+' then MARK, '' If ' ' > '+' then SPACE, '0' RS-422 Voltage: ± 7V RS-485 Voltage: 7V to +2 V Figure 9. RS-485/422 Signals RS-485 Topologies Tx Slave Rx Tx Slave 2 Rx Tx Slave n Rx MASTER Tx Rx 20 Ω 20 Ω Figure 0. 2-Wire Multidrop Network Using Terminating Resistors Tx Slave Rx Tx Slave 2 Rx Tx Slave n Rx MASTER Tx 20 Ω 20 Ω Rx 20 Ω 20 Ω Figure. 4-Wire Full-Duplex Multidrop Network Using Terminating Resistors RS-485 terminators are available at ni.com/serial. NI Serial Hardware Specifications and Features Guide 4 ni.com

16 RS-485 Transceiver Control 2-Wire Enable 4-Wire DTR/Echo DTR/No Echo Auto TX RX ON ON DTR ON DTR DTR TX TX Transceiver control is available on all NI Serial RS-485 interface products. UART Data Frame Example 0xD9 8 Data Bits, Odd Parity, Stop Bit Data RS V Idle S P S Idle Hardware Specifications 5 V RS V TX+ 0 V 5 V TX 0 V NI 9870 RS-232 C-Series Module C-Series modules are for use with the NI CompactRIO platform. For complete module and system specifications, refer to the NI 9870 Operating Instructions and Specifications. Specifications Voltages are for illustration only. Actual voltage levels may vary. The following specifications are typical for the range 40 to 70 C unless otherwise noted. Maximum baud rate kbps National Instruments Corporation 5 NI Serial Hardware Specifications and Features Guide

17 The NI 9870 supports arbitrary baud rates according to the following equation: BaudRate = Mbps / (Prescaler * Divider) Prescaler can be {4,..., 65535}. Divider can be or 4. As long as the actual baud rate is within 2% of the desired baud rate, communication errors should not happen. Maximum cable length pf equivalent Note Cable capacitance greater than 250 pf may adversely affect the maximum baud rate and thermal dissipation. Maximum RS232 Receive signal (RXD, CTS, DSR, DCD, RI) Continuous Voltage...±8 V Note Continuous RS232 input voltages in excess of ±8 V may cause excessive thermal dissipation. Data line ESD protection (human body model)...±5 kv MTBF...448,008 hours at 25 C; Bellcore Issue 6, Method, Case 3, Limited Part Stress Method Note Contact NI for Bellcore MTBF specifications at other temperatures or for MIL-HDBK-27F specifications. Power Requirements Power consumption from chassis Active mode W max Sleep mode...50 µw max Thermal dissipation (at 70 C) Active mode...5 W max Sleep mode W max Required external supply voltage range (V SUP )...+8 to +28 VDC NI Serial Hardware Specifications and Features Guide 6 ni.com

18 Power supply consumption from external supply V SUP Typical W Maximum... 2 W Physical Characteristics If you need to clean the module, wipe it with a dry towel. Weight... Approx. 54 g (5.4 oz) Safety Maximum Voltage Connect only voltages that are within these limits. RS232 Receive Signal-to-COM (RXD, CTS, DSR, DCD, RI)... ±25 V max, Measurement Category I RS232 Transmit Signal-to-COM (TX, RTS, DTR)... ±3.2 V max, Measurement Category I V SUP -to-com... ±28 V max, Measurement Category I Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics. Caution Do not connect to signals or use for measurements within Measurement Categories II, III, or IV. Isolation Voltages Port-to-earth ground Withstand V rms, verified by a 5 s dielectric withstand test Continuous VDC, Measurement Category I The maximum voltage that can be applied or output without creating a safety hazard. National Instruments Corporation 7 NI Serial Hardware Specifications and Features Guide

19 Shock and Vibration To meet these specifications, you must panel mount the CompactRIO system. Operating vibration, random (IEC )...5 g rms, 0 to 500 Hz Operating shock (IEC )...30 g, ms half sine, 50 g, 3 ms half sine, 8 shocks at 6 orientations Operating vibration, sinusoidal (IEC )...5 g, 0 to 500 Hz Environmental NI 987 RS-485 C-Series Module CompactRIO modules are intended for indoor use only. For outdoor use, mount the CompactRIO system in a suitably rated enclosure. Refer to the installation instructions for the chassis you are using for more information about meeting these specifications. Operating temperature to 70 C Storage temperature to 85 C Ingress protection...ip 40 Operating humidity...0 to 90% RH, noncondensing Storage humidity...5 to 95% RH, noncondensing Maximum altitude...2,000 m Pollution Degree (IEC 60664)...2 C-Series modules are for use with the NI CompactRIO platform. For complete module and system specifications, refer to the NI 987 Operating Instructions and Specifications Specifications The following specifications are typical for the range 40 to 70 C unless otherwise noted. Maximum baud rate Mbps NI Serial Hardware Specifications and Features Guide 8 ni.com

20 The NI 987 supports arbitrary baud rates according to the following equation: BaudRate = Mbps / (Prescaler * Divider) Prescaler can be ( ). Divider can be or 4. As long as the actual baud rate is within 2% of the desired baud rate, communication errors should not happen. Maximum cable length....2 km (4,000 ft.) Data line ESD protection (human body model)... ±5 kv MTBF... 54,06 hours at 25 C; Bellcore Issue 6, Method, Case 3, Limited Part Stress Method Note Contact NI for Bellcore MTBF specifications at other temperatures or for MIL-HDBK-27F specifications. Power Requirements Power consumption from chassis Active mode W max Sleep mode µw max Thermal dissipation (at 70 C) Active mode....5 W max Sleep mode mw max Required external supply voltage range (V SUP ) to +28 VDC Power supply consumption from external supply V SUP Typical... W Maximum W Physical Characteristics If you need to clean the module, wipe it with a dry towel. Weight... Approx. 53 g (5.4 oz) National Instruments Corporation 9 NI Serial Hardware Specifications and Features Guide

21 Safety Maximum Voltage Connect only voltages that are within these limits. RS485/RS422 Port-to-COM... 8 to +3 VDC max, Measurement Category I V SUP -to-com... ±28 V max, Measurement Category I Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics. Caution Do not connect to signals or use for measurements within Measurement Categories II, III, or IV. Isolation Voltages Port-to-earth ground Withstand V rms, verified by a 5 s dielectric withstand test Continuous...60 VDC, Measurement Category I Shock and Vibration To meet these specifications, you must panel mount the CompactRIO system. Operating vibration, random (IEC )...5 g rms, 0 to 500 Hz Operating shock (IEC )...30 g, ms half sine, 50 g, 3 ms half sine, 8 shocks at 6 orientations Operating vibration, sinusoidal (IEC )...5 g, 0 to 500 Hz The maximum voltage that can be applied or output without creating a safety hazard. NI Serial Hardware Specifications and Features Guide 20 ni.com

22 PCI Serial Hardware Environmental CompactRIO modules are intended for indoor use only. For outdoor use, mount the CompactRIO system in a suitably rated enclosure. Refer to the installation instructions for the chassis you are using for more information about meeting these specifications. Operating temperature to 70 C Storage temperature to 85 C Ingress protection... IP 40 Operating humidity... 0 to 90% RH, noncondensing Storage humidity... 5 to 95% RH, noncondensing Maximum altitude... 2,000 m Pollution Degree (IEC 60664)... 2 This section describes the characteristics of the PCI serial hardware and the recommended operating conditions. PCI-843x Series Hardware PCI-8430/2 (RS-232) and PCI-843/2 (RS-485/422) Dimensions cm ( in.) I/O connector... DB-9 male connector Power requirement (from PCI channel) Weight PCI-8430/2 +5 VDC ma typical 500 ma maximum PCI-843/2 +5 VDC ma typical 700 ma maximum PCI-8430/ g PCI-843/ g National Instruments Corporation 2 NI Serial Hardware Specifications and Features Guide

23 Maximum baud rate PCI-8430/2... Mbps PCI-843/2...3 Mbps Boards support any baud rate below the maximum. PCI-8430/4 (RS-232) and PCI-843/4 (RS-485/422) Dimensions cm ( in.) I/O connector...0-position modular jack (0P0C) Power requirement (from PCI channel) Weight PCI-8430/4 +5 VDC ma typical 600 ma maximum PCI-843/4 +5 VDC ma typical. A maximum PCI-8430/ g PCI-843/ g Maximum baud rate PCI-8430/4... Mbps PCI-843/4...3 Mbps Boards support any baud rate below the maximum. PCI-8430/8 (RS-232) and PCI-843/8 (RS-485/422) Dimensions cm ( in.) I/O connector pin, SCSI type connector Power requirement (from PCI channel) PCI-8430/8 +5 VDC ma typical 900 ma maximum The four-port PCI serial boards require cables, included in your kit, to convert the 0-position modular jacks (0P0C) to DB-9 male connectors. 2 The eight-port PCI serial boards require a cable, included in your kit, to convert the 68-pin connector to eight DB-9 connectors. NI Serial Hardware Specifications and Features Guide 22 ni.com

24 Weight PCI-843/8 +5 VDC....3 A typical.9 A maximum PCI-8430/ g PCI-843/ g Maximum baud rate PCI-8430/8... Mbps PCI-843/ Mbps Boards support any baud rate below the maximum. PCI-8430/6 (RS-232) Dimensions cm ( in.) I/O connector pin, VHDCI 2 Power requirement (from PCI channel) PCI-8430/6 +5 VDC ma typical.4 A maximum Weight g Maximum baud rate... Mbps Board supports any baud rate below the maximum. PCI-8432/2 (RS-232) and PCI-8433/2 (RS-485/422) Dimensions cm ( in.) I/O connector... DB-9 male connector Operating rated voltage (continuous) RS V to +25 V RS V to + 2 V The 6-port PCI serial boards require two cables, included in your kit, to convert the two 68-pin connectors to the 6 (2 8) DB-9 male connectors. National Instruments Corporation 23 NI Serial Hardware Specifications and Features Guide

25 Isolation voltages Port-to-port Continuous...60 VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Port-to-host Continuous...60 VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Power requirement (from PCI channel) Weight PCI-8432/2 +5 VDC ma typical 570 ma maximum PCI-8433/2 +5 VDC ma typical 570 ma maximum PCI-8432/ g PCI-8433/ g Maximum baud rate PCI-8432/2... Mbps PCI-8433/2...3 Mbps Boards support any baud rate below the maximum. PCI-8432/4 (RS-232) and PCI-8433/4 (RS-485/422) Dimensions cm ( in.) I/O connector...0-position modular jack (0P0C) Operating rated voltage (continuous) RS V to +25 V RS V to + 2 V The four-port PCI serial boards require cables, included in your kit, to convert the 0-position modular (0P0C) jacks to DB-9 male connectors. NI Serial Hardware Specifications and Features Guide 24 ni.com

26 Isolation voltages Port-to-port Continuous VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Port-to-host Continuous VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Power requirement (from PCI channel) Weight PCI-8432/4 +5 VDC ma typical 85 ma maximum PCI-8433/4 +5 VDC ma typical.2 A maximum PCI-8432/ g PCI-8433/ g Maximum baud rate PCI-8432/4... Mbps PCI-8433/ Mbps Boards support any baud rate below the maximum. Environmental Characteristics (for All PCI Interfaces) Operating Environment Ambient temperature... 0 to 55 C IEC and IEC ) Relative humidity... 0 to 90%, noncondensing IEC ) Altitude (maximum)... 2,000 m National Instruments Corporation 25 NI Serial Hardware Specifications and Features Guide

27 Pollution Degree...2 Indoor use only. Storage Environment Ambient temperature to 70 C IEC and IEC ) Relative humidity...5 to 95%, noncondensing IEC ) Other Specifications Maximum cable length RS m (limited by EMC/surge) RS ,500 pf equivalent (TIA-EIA-232-F 2..4) Data line ESD protection (human body model) RS ±5 kv RS ±5 kv Note This equipment is intended for indoor use only. Safety This product meets the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC 600-, EN 600- UL 600-, CSA 600- Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. RS-485 is capable of.2 km (4,000 ft) without surge limitation. NI Serial Hardware Specifications and Features Guide 26 ni.com

28 Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN 6326 (IEC 6326): Class A emissions; Basic immunity EN 550 (CISPR ): Group, Class A emissions AS/NZS CISPR : Group, Class A emissions FCC 47 CFR Part 5B: Class A emissions ICES-00: Class A emissions Note For the standards applied to assess the EMC of this product, refer to the Online Product Certification section. Note For EMC compliance, operate this device with shielded cabling. CE Compliance This product meets the essential requirements of applicable European Directives as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/08/EC; Electromagnetic Compatibility Directive (EMC) Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. National Instruments Corporation 27 NI Serial Hardware Specifications and Features Guide

29 Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/weee. PCI Express Serial Hardware RoHS National Instruments (RoHS) National Instruments RoHS ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china.) This section describes the characteristics of the PCI Express serial hardware and the recommended operating conditions. NI PCIe-843x Series Hardware NI PCIe-8430/6 (RS-232) and NI PCIe-843/6 (RS-485/422) Dimensions (without bracket) cm ( in.) I/O connectors NI PCIe-8430/6 RS pin VHDCI 2 PCI Express...x NI PCIe-843/6 RS pin VHDCI 2 PCI Express...x Power requirement (from PCI Express channel) NI PCIe-8430/ VDC ma typical,.5 A maximum +2 VDC...20 ma typical 250 ma maximum NI PCIe-843/ VDC A typical, 3 A maximum +2 VDC...20 ma typical 250 ma maximum The 6-port PCI Express serial boards require two cables, included in your kit, to convert the two 68-pin connectors to the 6 (2 8) DB-9 male connectors. 2 These values are based on the assumption that all 6 ports (for the NI PCIe-843/6) or 8 ports (for the NI PCIe-843/8) are using a 620 Ω bias resistor and NI-offered terminators installed on both ends of the cable. NI Serial Hardware Specifications and Features Guide 28 ni.com

30 Weight NI PCIe-8430/ g NI PCIe-843/ g Maximum baud rate NI PCIe-8430/6... Mbps NI PCIe-843/ Mbps Boards support any baud rate below the maximum. NI PCIe-8430/8 (RS-232) and NI PCIe-843/8 (RS-485/422) Dimensions (without bracket) cm ( in.) I/O connectors NI PCIe-8430/8 RS pin VHDCI PCI Express... x NI PCIe-843/8 RS pin VHDCI PCI Express... x Power requirement (from PCI Express channel) Weight NI PCIe-8430/ VDC ma typical 750 ma maximum +2 VDC ma typical 220 ma maximum NI PCIe-843/ VDC ma typical,.5 A maximum +2 VDC ma typical 220 ma maximum NI PCIe-8430/ g NI PCIe-843/ g The 8-port PCI Express serial boards require a cable, included in your kit, to convert the 68-pin connector to eight DB-9 male connectors. 2 These values are based on the assumption that all 6 ports (for the NI PCIe-843/6) or 8 ports (for the NI PCIe-843/8) are using a 620 Ω bias resistor and NI-offered terminators installed on both ends of the cable. National Instruments Corporation 29 NI Serial Hardware Specifications and Features Guide

31 Maximum baud rate NI PCIe-8430/8... Mbps NI PCIe-843/8...3 Mbps Boards support any baud rate below the maximum. Environmental Characteristics (for All PCI Express Interfaces) Operating Environment Ambient temperature...0 to 55 C IEC and IEC ) Relative humidity...0 to 90%, noncondensing IEC ) Altitude (maximum)...2,000 m Indoor use only. Storage Environment Ambient temperature to 70 C IEC and IEC ) Relative humidity...5 to 95%, noncondensing IEC ) Other Specifications Maximum cable length RS m (limited by EMC/surge) RS ,500 pf equivalent (TIA-EIA-232-F 2..4) Data line ESD protection (human body model) RS ±5 kv RS ±5 kv RS-485 is capable of.2 km (4,000 ft) without surge limitation. NI Serial Hardware Specifications and Features Guide 30 ni.com

32 Note This equipment is intended for indoor use only. Safety This product meets the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC 600-, EN 600- UL 600-, CSA 600- Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN 6326 (IEC 6326): Class A emissions; Basic immunity EN 550 (CISPR ): Group, Class A emissions AS/NZS CISPR : Group, Class A emissions FCC 47 CFR Part 5B: Class A emissions ICES-00: Class A emissions Note For the standards applied to assess the EMC of this product, refer to the Online Product Certification section. Note For EMC compliance, operate this device with shielded cabling. CE Compliance This product meets the essential requirements of applicable European Directives as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/08/EC; Electromagnetic Compatibility Directive (EMC) Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. National Instruments Corporation 3 NI Serial Hardware Specifications and Features Guide

33 Environmental Management NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/weee. PXI Serial Hardware RoHS National Instruments (RoHS) National Instruments RoHS ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china.) This section describes the characteristics of the PXI serial hardware and the recommended operating conditions. PXI-843x Serial Hardware PXI-8430/2 (RS-232) and PXI-843/2 (RS-485/422) Dimensions mm ( in.) I/O connector...db-9 male connector Power requirement (from PXI channel) PXI-8430/2 +5 VDC ma typical 500 ma maximum PXI-843/2 Weight +5 VDC ma typical 750 ma maximum PXI-8430/ g PXI-843/ g NI Serial Hardware Specifications and Features Guide 32 ni.com

34 Maximum baud rate PXI-8430/2... Mbps PXI-843/ Mbps Boards support any baud rate below the maximum. PXI-8430/4 (RS-232) and PXI-843/4 (RS-485/422) Dimensions mm ( in.) I/O connector... 0-position modular jack (0P0C) Power requirement (from PXI channel) Weight PXI-8430/4 +5 VDC ma typical 600 ma maximum PXI-843/4 +5 VDC ma typical. A maximum PXI-8430/ g PXI-843/ g Maximum baud rate PXI-8430/4... Mbps PXI-843/ Mbps Boards support any baud rate below the maximum. PXI-8430/8 (RS-232) and PXI-843/8 (RS-485/422) Dimensions mm ( in.), 3U I/O connector pin SCSI (68-pin SCSI to eight DB-9 male connector adapter cable included) The four-port PXI serial boards require cables, included in your kit, to convert the 0-position modular jacks (0P0C) to DB-9 male connectors. 2 The eight-port PXI serial boards require a cable, included in your kit, to convert the 68-pin connector to eight DB-9 connectors. National Instruments Corporation 33 NI Serial Hardware Specifications and Features Guide

35 Power requirement (from PXI channel) Weight PXI-8430/8 +5 VDC... A typical.5 A maximum PXI-843/8 +5 VDC ma typical.4 A maximum PXI-8430/ g PXI-843/ g Shock and vibration Operational shock...30 g peak, half-sin, ms pulse IEC Test profile developed in accordance with MIL-PRF-28800F.) Maximum baud rate PXI-8430/8... Mbps PXI-843/8...3 Mbps Boards support any baud rate below the maximum. PXI-8430/6 (RS-232) Dimensions mm ( in.), 3U I/O connector...68-pin VHDCI 2 Power requirement (from PXI channel) PXI-8430/6 +5 VDC ma typical.4 A maximum Weight...57 g Maximum baud rate... Mbps Board supports any baud rate below the maximum. The 6-port PXI serial boards require two cables, included in your kit, to convert the two 68-pin connectors to the 6 (2 8) DB-9 male connectors. NI Serial Hardware Specifications and Features Guide 34 ni.com

36 PXI-8432/2 (RS-232) and PXI-8433/2 (RS-485/422) Dimensions mm ( in.), 3U I/O connector... DB-9 male connector 2 Operating rated voltage (continuous) RS V to +25 V RS V to + 2 V Isolation voltages Port-to-port Continuous VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Port-to-host Continuous VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Power requirement (from PXI channel) PXI-8432/2 +5 VDC ma typical A maximum PXI-8433/2 +5 VDC ma typical A maximum Weight PXI-8432/ g PXI-8433/ g Shock and vibration Operational shock g peak, half-sin, ms pulse IEC Test profile developed in accordance with MIL-PRF-28800F.) National Instruments Corporation 35 NI Serial Hardware Specifications and Features Guide

37 Random vibration Operating...5 to 500 Hz, 0.3 g rms Nonoperating...5 to 500 Hz, 2.4 g rms (Tested in accordance with IEC Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.) Maximum baud rate PXI-8432/2... Mbps PXI-8433/2...3 Mbps Boards support any baud rate below the maximum. PXI-8432/4 (RS-232) and PXI-8433/4 (RS-485/422) Dimensions mm ( in.), 3U I/O connector...0-position modular jack (0P0C) Operating rated voltage (continuous) RS V to +25 V RS V to + 2 V Isolation voltages Port-to-port Continuous...60 VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Port-to-host Continuous...60 VDC (CAT I) Withstand V rms, verified by a 5 s dielectric withstand test Power requirement (from PXI channel) PXI-8432/4 +5 VDC ma typical 2 A maximum The four-port PXI serial boards require cables, included in your kit, to convert the 0-position modular jacks (0P0C) to DB-9 male connectors. NI Serial Hardware Specifications and Features Guide 36 ni.com

38 Weight PXI-8433/4 +5 VDC ma typical 2 A maximum PXI-8432/ g PXI-8433/ g Maximum baud rate PXI-8432/4... Mbps PXI-8433/ Mbps Boards support any baud rate below the maximum. Environmental Characteristics (for All PXI Interfaces) Operating Environment Ambient temperature... 0 to 55 C IEC and IEC ) Relative humidity... 0 to 90%, noncondensing IEC ) Altitude (maximum)... 2,000 m Pollution Degree... 2 Indoor use only. Storage Environment Ambient temperature to 70 C IEC and IEC ) Relative humidity... 5 to 95%, noncondensing IEC ) National Instruments Corporation 37 NI Serial Hardware Specifications and Features Guide

39 Other Specifications Maximum cable length RS m (limited by EMC/surge) RS ,500 pf equivalent (TIA-EIA-232-F 2..4) Data line ESD protection (human body model) RS ±5 kv RS ±5 kv Note This equipment is intended for indoor use only. Safety This product meets the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC 600-, EN 600- UL 600-, CSA 600- Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN 6326 (IEC 6326): Class A emissions; Basic immunity EN 550 (CISPR ): Group, Class A emissions AS/NZS CISPR : Group, Class A emissions FCC 47 CFR Part 5B: Class A emissions ICES-00: Class A emissions Note For the standards applied to assess the EMC of this product, refer to the Online Product Certification section. Note For EMC compliance, operate this device with shielded cabling. RS-485 is capable of.2 km (4,000 ft) without surge limitation. NI Serial Hardware Specifications and Features Guide 38 ni.com

40 CE Compliance This product meets the essential requirements of applicable European Directives as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/08/EC; Electromagnetic Compatibility Directive (EMC) Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/weee. RoHS National Instruments (RoHS) National Instruments RoHS ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china.) National Instruments Corporation 39 NI Serial Hardware Specifications and Features Guide

41 USB Serial Hardware This section describes the characteristics of the USB serial hardware and the recommended operating conditions. USB-232 (RS-232) and USB-485 (RS-485/422) Dimensions cm ( in.) Case material...pvc Weight USB g (0.27 lb) USB g (0.26 lb) I/O connector...db-9 male connector USB connector...captive cable with USB series A plug Power requirement (from USB channel) USB VDC...75 ma typical 500 ma maximum USB VDC...80 ma typical 00 ma maximum Maximum baud rate USB kbps USB kbps Boards support standard baud rates below the maximum. USB-232/2, USB-232/4 (USB-232), USB-485/2, and USB-485/4 (RS-485/422) Dimensions cm ( in.) Case material...hard plastic with metal baseplate Weight g (0.83 lb) I/O connector...db-9 male connector USB connector...usb series B NI Serial Hardware Specifications and Features Guide 40 ni.com

42 Power requirement (from USB channel) USB-485/2 +5 VDC ma typical 500 ma maximum USB-232/2 +5 VDC ma typical 500 ma maximum USB-232/4 +5 VDC ma typical 500 ma maximum Power requirement (from external supply) USB-485/4 (9 V 30 V) +2 VDC (typical) ma typical 500 ma maximum Maximum baud rate USB-232/2 and USB-232/ kbps USB-485/2 and USB-485/ kbps Boards support standard baud rates below the maximum. Environmental Characteristics (for All USB Interfaces) Operating Environment Ambient temperature... 0 to 70 C IEC and IEC ) Relative humidity... 0 to 90%, noncondensing IEC ) Altitude (maximum)... 2,000 m Pollution Degree... 2 Indoor use only. Storage Environment Ambient temperature One port to 80 C IEC and IEC ) National Instruments Corporation 4 NI Serial Hardware Specifications and Features Guide

43 Two and four port to 85 C IEC and IEC ) Relative humidity...5 to 95%, noncondensing IEC ) Other Specifications Maximum cable length RS m (limited by EMC/surge) RS ,500 pf equivalent (TIA-EIA-232-F 2..4) Data line ESD protection (human body model) RS ±5 kv RS ±5 kv Note This equipment is intended for indoor use only. Safety This product meets the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC 600-, EN 600- UL 600-, CSA 600- Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN 6326 (IEC 6326): Class A emissions; Basic immunity EN 550 (CISPR ): Group, Class A emissions AS/NZS CISPR : Group, Class A emissions FCC 47 CFR Part 5B: Class A emissions ICES-00: Class A emissions RS-485 is capable of.2 km (4,000 ft) without surge limitation. NI Serial Hardware Specifications and Features Guide 42 ni.com

44 Note For the standards applied to assess the EMC of this product, refer to the Online Product Certification section. Note For EMC compliance, operate this device with shielded cabling. CE Compliance This product meets the essential requirements of applicable European Directives as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/08/EC; Electromagnetic Compatibility Directive (EMC) Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/weee. RoHS National Instruments (RoHS) National Instruments RoHS ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china.) National Instruments Corporation 43 NI Serial Hardware Specifications and Features Guide

45 ENET Serial Hardware This section describes the characteristics of the ENET serial hardware, along with the recommended operating conditions. Electrical Characteristics Power requirement (from external supply) External supply (9 V 30 V) +2 VDC (typical) ma typical 750 ma maximum Environmental Characteristics Operating Environment Ambient temperature...0 to 70 C IEC and IEC ) Relative humidity...0 to 90%, noncondensing IEC ) Altitude (maximum)...2,000 m Storage Environment Ambient temperature to 85 C IEC and IEC ) Relative humidity...5 to 95%, noncondensing IEC ) Physical Characteristics Overall case size (dimensions) cm ( in.) Case material...hard plastic with metal baseplate Weight g (0.87 lb) Serial connectors...db-9 male connector NI Serial Hardware Specifications and Features Guide 44 ni.com