HDBaseT-8x8Matrix. HDBaseT-8x8Matrix. HDCP2.2 HDBT Lite2U Modular8x8 HDMI Matrix
|
|
- Matilda Ford
- 5 years ago
- Views:
Transcription
1 HDCP2.2 HDBT Lite2U Modular8x8 HDMI Matrix Factor Electronics 59 McConnell Drive Burnaby B.C. Canada V5A-J7 Toll Free
2 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. SURGE PROTECTION DEVICE RECOMMENDED This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. SAFTY AND NOTICE. The transmission distances of HDMI over UTP cables are measured using TE CONNECTIVITY EIA/TIA-568-B termination (T568B) for CAT cables is recommended for better performance.. DO NOT use 568A/568B standard mixed CAT cable (cross-over cable) because there are 2 pairs swapped, this will make POE OVER-CURRENT and damage POE components. Please use straight-through CAT cable (both RJ5 headers are 568A or 568B standard).. It is recommended that power up the device after connections of source, sink and CAT cable. 5. To reduce the interference among the unshielded twisted pairs of wires in CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close parallel proximity to mains power cables. Shielded CAT cables can be used to improve EMI problems, which is worsen in long transmission. 6. Because the quality of the CAT cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality, the actual transmission range is subject to one s choice of CAT cables. 7. Do not substitute or use any other Power Supply other than the enclosed unit, or a Factor Electronics approved Replacement Part. Doing so will void the warranty and potentially expose the user to dangerous voltages resulting in an electrical shock. 8. Do not disassemble the device for any reason. Doing so will void the manufacturer s warranty. Also, our unique case is an integral part of the design of this unit and is responsible for cooling and circuitry shielding. Any modifications to this case will potentially cause malfunction and product failure. 9. Do not expose the device to water, moisture, or liquids. Possible electric shock may result as well as failure of the unit to operate. RMA Policy contact Factor for an RMS at info@factorelectronics.com When returning product to Factor Electronics for any reason, the customer should fill out the official RMA form to obtain a RMA number. Without the permission or approval, Factor Electronics will not be responsible for any return.this can be initiated by ing or calling your related sales. All requests are processed within 8 hours. Standard Replacement For customers that agree to return defective product to Factor Electronics first, a Standard Replacement option is available. An RMA number must first be issued by sales. This RMA number will need to be referenced on the outside of the return shipment. Upon receipt of the defective product, Factor Electronics will, at its discretion, either repair or replace the product and ship it out in the most expeditious manner possible. Subject to availability, the replacement product will be shipped on the business day following receipt of the defective product. In the event the product returned to Factor Electronics has been discontinued (i.e. the product is no longer being manufactured by Factor Electronics but is still under warranty), Factor Electronics will, at its discretion, either repair or replace with recertified product. Once you have obtained an RMA number After obtaining an RMA number from Factor, you must send the product - freight prepaid - to Factor Electronics The Factor Electronics RMA number must be prominently displayed on the outside of your package. If you send your product to Factor Electronics without the RMA number prominently displayed on the outside of the package, it will be returned to you unopened. Please use a shipping company that can demonstrate proof of delivery. Factor Electronics does not accept responsibility for any lost shipments unless proof of delivery to Factor Electronics is provided. Please note: Product shipped to Factor Electronics must be properly packaged to prevent loss or damage in transit. Shipping your RMA to Factor Electronics using regular mailing envelopes is not acceptable, as they do not protect the product from damage during shipping. Factor Electronics will not repair or replace a module that is shipped in such a way that the product is not properly protected. Factor Electronics will not accept any product that has been damaged as a result of accident, abuse, misuse, natural or personal disaster, or any unauthorized disassemble, repair or modification. 26
3 Maintenance Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit. Warranty Policy Factor Electronics products are warranted against defects in material and workmanship for two years from the date of shipment. During the warranty period, Factor Electronics will, at its option, repair or replace products that prove to be defective. Repairs are warranted for the remainder of the original warranty or a 90 day extended warranty, whichever is longer. For equipment under warranty, the owner is responsible for freight to Factor Electronics and all related customs, taxes, tariffs, insurance, etc. Factor Electronics is responsible for the freight charges only for return of the equipment from the factory to the owner. All equipment returned for warranty repair must have a valid RMA number issued prior to return and be marked clearly on the return packaging. Factor Electronics strongly recommends all equipment be returned in its original packaging. Factor Electronics obligations under this warranty are limited to repair or replacement of failed parts, and the return shipment to the buyer of the repaired or replaced parts. Limitations of Warranty The warranty does not apply to any part of a product that has been installed, altered, repaired, or misused in any way that, in the opinion of Factor Electronics, would affect the reliability or detracts from the performance of any part of the product, or is damaged as the result of use in a way or with equipment that had not been previously approved by Factor Electronics. The warranty does not apply to any product or parts thereof where the serial number or the serial number of any of its parts has been altered, defaced, or removed. The warranty does not cover damage or loss incurred in transportation of the product. The warranty does not cover replacement or repair necessitated by loss or damage from any cause beyond the control of Factor Electronics, such as lightning or other natural and weather related events or wartime environments. The warranty does not cover any labor involved in the removal and or reinstallation of warranted equipment or parts on site, or any labor required to diagnose the necessity for repair or replacement. The warranty excludes any responsibility by Factor Electronics for incidental or consequential damages arising from the use of the equipment or products, or for any inability to use them either separate from or in combination with any other equipment or products. A fixed charge established for each product will be imposed for all equipment returned for warranty repair where Factor Electronics cannot identify the cause of the reported failure. Exclusive Remedies Factor Electronics warranty, as stated is in lieu of all other warranties, expressed, implied, or statutory, including those of merchantability and fitness for a particular purpose. The buyer shall pass on to any purchaser, lessee, or other user of Factor Electronics products, the aforementioned warranty, and shall indemnify and hold harmless Factor Electronics from any claims or liability of such purchaser, lessee, or user based upon allegations that the buyer, its agents, or employees have made additional warranties or representations as to product preference or use. The remedies provided herein are the buyer s sole and exclusive remedies. Factor Electronics shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other legal theory. Table of Content Introduction... Features... Panel Descriptions... Front Panel... Back Panel... Remote Control Description... 5 Master Remote Control... 5 Satellite Remote Control... 6 Application Diagram... 6 Specifications... 7 Package Contents... 7 RS-22 Pin Assignment... 7 RS22 and Telnet Commands... 8 GUI Control... 9 PC System:... 9 Installation... 9 Preparation... 9 Common information... 0 General page... 0 Set TCP control configuration... Port Tag page... Edit Input port tags... 2 Edit Output port tags... 2 Setting page... Pop-up tag messages... Pop-up Menu... Edit selected pre-setting item... EDID control page... 5 IR Configuration page... 5 FW upgrade page... 6 Set Video Input Souce... 7 Set Audio Source for Input... 7 Remote HDBT Receiver IR Output Control... 7 Global All IR In... 8 Global All IR Out... 8 Global RS-22 Route... 8 Web GUI... 9 How to enter Web GUI... 9 Admin account... 9 Zone Page Status Page Config Page... 2 Output Page... 2 Input Page Preset Page EDID Page... 2 Audio Page... 2 IR&RS22 Page... 2 Users Page... 2 Maintenance Warranty Policy Limitations of Warranty Exclusive Remedies RMA Policy Standard Replacement Once you have obtained an RMA number Please note:
4 Introduction The HDBaseT-8X8MATRIXis a modular design 8x HDMI Inputs and 8x HDMI & 8x HDBaseT outputs matrix switcher with audio embedding and de-embedding, supporting080p Full HD up to K plus all D formats, along with multichannel digital audio formats such as Dolby True HD and DTS-HD Master Audio. Based on HDBaseT technology, the output distance can reach up to 70m/20ft via Cat5e/Cat6.Each source can be routed to any display using the front-panel push buttons, IR remote control, RS-22 interface, or via TCP/IP. Features 2U modular design, flexible input and output cards selection. HDCP 2.2/HDCP.x and DVI compliant. HDBaseT chipset inside for input or output distance up to 70m/20ft. The matrix can power the remote transmitter thru POH, no power is supply needed for the receivers. Supports resolutions up to 080p@60Hz, K@0Hz (::), K@60Hz (:2:0). Support Audio embed and de-embed. Allows any source to be displayed on multiple displays at the same time. Allows any HDMI display to view any HDMI source at any time. Dolby TrueHD and DTS-HD master audio pass through HDMI output. Advanced EDID management for rapid integration of sources and displays. Front-panel LCD display for status feedback. Multiple switching mode, push button, IR remote control, RS-22 control, and TCP/IP control. Easy installation with the included rack kit. Full D pass-through. IR & RS22 Page You can set the routing path for the IR & RS22. Users Page You can create, edit and remove guest account info.: The Admin account can't be deleted. Panel Descriptions Front Panel. LCD Display -- Shows the status of input-output selection, EDID info and so on. 2. IR Receiver Window -- -Receives the IR signal from the master remote control.. Power LED Indicator -- Indicates the status of the power ON/OFF for the matrix.. Power Button -- Press to power on/off the matrix. 5. HDMI Output Selection Buttons to 8 -- Press to select outputs to 8. Note: Hold the OUTPUT # Button for 0 seconds to RESET the unit. 6. All Button for the HDMI Outputs -- Press to select all of the outputs from to Menu Button -- Press to enter the EDID set mode. Three EDID segments will display on the LCD panel formatted as: INPUT VIDEO AUDIO, for example: IN 080P 2.0CH, means to set 080P 2.0CH EDID to INPUT. The blinking segment can be changed Segment choices are listed below: 2
5 EDID Page You can select built-in EDID patterns for each input, and select EDID priority for HDMI/HDBT. Audio Page You can select the audio source for each output, set audio delay values, and control audio volume. INPUT VIDEO AUDIO Note IN 080I 2.0CH. IN2 080P 5.CH IN D 7.CH IN K2K NONE IN5 D02 D02=DVI 02 x 768 IN6 D080 D080=DVI 920 x 080 IN7 D200 D200=DVI 920 x 200 IN8 OUT OUT=Copy OUTPUT EDID to INPUTx ALL OUT2 ALL=Set EDID to ALL INPUTs OUT2=Copy OUTPUT2 EDID to INPUTx OUT OUT=Copy OUTPUT EDID to INPUTx OUT OUT=Copy OUTPUT EDID to INPUTx OUT5 OUT5=Copy OUTPUT5 EDID to INPUTx OUT6 OUT6=Copy OUTPUT6 EDID to INPUTx OUT7 OUT7=Copy OUTPUT7 EDID to INPUTx OUT8 OUT8=Copy OUTPUT8 EDID to INPUTx 8. Up Selection Button -- Press to change a segment s value. 9. ESC -- Press to quit the EDID set mode. 0. Rubber Feet. Lock LED Indicator -- Indicates the lock status. 2. Lock Button -- Press to lock all front panel buttons. HDMI Input Selection Button to 8 -- Press to select the input from to 8.. PTP Button -- Press to mirror all inputs and outputs (e.g. output to input, output 2 to input2 and so on). 5. Selection Button -- Press to select segment to change settings. The selected segment will blink. 6. Down Selection Button -- Press to change a segment s value. 7. Enter Button -- Press to set the EDID to a specified INPUT or copy the EDID from a specified OUTPUT to a specified INPUT. Back Panel. RJ5 -- TCP control 2. RS22 Port to pin phoenix terminal connector. Master RS22 Port -- DB9, female.. L/R In to mm stereo phone-jack. 5. Coaxial Output to 8 -- RCA connector. 6. L/R Output to mm stereo phone-jack. 7. IR In to mm stereo phone-jack, work with control processor. 8. IR Out to mm mono phone-jack, connect to IR transmitter cable. 9. Global IR In --.5mm stereo phone-jack. 2
6 0. Global IR Out --.5mm mono phone-jack.. Power Switch -- Power on/off the unit. 2. Rubber Feet. HDMI Input - -- Connect to HDMI Sources -.. HDMI Input Connect to HDMI Sources HDBT Output - -- Connect to HDBT Receivers. 6. HDMI Output - -- Connect to Displays. 7. HDBT Output Connect to HDBT Receivers. 8. HDMI Output Connect to Displays. 9. DC Power Input -- 2V/6A power input Input Page You can set the Input Source priority (Force HDMI, Force HDBT, Auto HDMI or Auto HDBT), check the current input source and check the HDMI/HDBT connect status. Remote Control Description Master Remote Control Preset Page There are several preset input/output settings to choose from. Output and Input select A. OUTPUT-X select INPUT-Y:. Press OUTPUT-X (X =outputs to 8 ) Press INPUT-Y ( Y = inputs to 8 ) 2. Press OUTPUT-X (X = outputs to 8 ) press the left and right arrow buttons to select the input. B. All outputs, select INPUT-Y: Press the ALL button zone OUTPUT Press INPUT-Y button ( Y = inputs to 8), then INPUT-Y will be switched to ALL OUTPUTS C. Mirror all inputs and outputs (Ex. Input to output, input 2 to output 2, etc.): Press PTP button in Zone OUTPUT EDID Set Up A. Fixed EDID to INPUT-Y/ALL Press 080I/080P/D/K Press 2.0CH/5.CH/7.CH INPUT-Y/ALL button in Zone INPUT 5 22
7 Config Page You can set the DHCP, IP Address, Gateway and Subnet Mask, you can also custom name the Inputs (such as Sky STB, SONY DVD, SAMSUNG DVD, etc) and Outputs (such Room, Room 2, Room, etc.) B. Copy the EDID of OUTPUT-X to INPUT-Y/ALL Press the COPY button Press the OUTPUT-X button Press the INPUT-Y/ALL button C. User defined EDID to INPUT-Y/ALL Press the USER/USER2 button Press INPUT-Y/ALL NOTE: Button sequences should be completed in 5 seconds, otherwise the, operation will be discarded. Satellite Remote Control Application Diagram Output Page You can select the Input for each Output, enable/disable each Output and set the priority for HDMI/HDBaseT. This page also shows the connect status for HDMI/HDBaseT ports. 2 6
8 Specifications Bandwidth: Video Input Connectors: Video Output Connectors: Audio Input Connectors: Audio Output Connectors: RS-22 serial port: TCP/IP Control: IR Input ports: IR Output ports: Rack-Mountable: Dimensions (W x H x D): Shipping Weight: Operating Temperature: Storage Temperature : Power Supply: 0.2Gbps 8x HDMI Type A 8x HDMI Type A, 8x RJ-5 connector 8x.5mm stereo jack 8x.5mm stereo jack,8x RCA (SPDIF) x DB9 female, 8x -pin phoenix terminal connector x RJ-5 9x.5mm stereo jack 9x.5mm mono jack 2U rack height, rack ears included 0mm x 282mm x 88mm, without feet 7.Kg (Matrix Only) 2 F to 0 F (0 C to 0 C) - F to 0 F (-20 C to 60 C) 00V-20V Zone Page Same as the Guest account interface Package Contents ) x 2) x 2V/6A Power Supply, ) x Power Cord ) x Master Remote Control 5) 8x Satellite Remote Control 6) 9x IR Transmitter 7) 9x IR Receiver. 8) xrack-mount ears 9) x RS22 (DB9) to -pin Phoenix Terminal Cable Status Page System info and Web GUI info including Model Number, Firmware Version, Power Status, IP status, IP address, Gateway, Subnet Mask, MAC Address and UI Version. You can turn the matrix ON/OFF by click the power icon at the bottom. RS-22 Pin Assignment Remote Control Console PIN Assignment PIN Assignment NC NC 2 Tx 2 Rx Rx Tx NC NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate: bps Data Bit: 8-bit Parity: None Stop Bit: -bit Flow Control: None 7 20
9 Web GUI How to enter the Web GUI Type in the IP address " " in your web browser to enter the Web GUI. First time login the matrix will enter the default Guest account, in which you can only check limited system info and perform simple source switching. Admin account Logout of the guest account and login to the admin account for full access. Account Name: admin Password: 2 RS22 and Telnet Commands No. Command Action? Print Help Information 2 HELP Print Help Information STATUS Print System Status And Port Status PON Power On, System Run On Normal State 5 POFF Power Off, System Run On Power Save State 6 IR ON/OFF Set System IR Control On Or Off 7 KEY ON/OFF Set System KEY Control On Or Off 8 DBG ON/OFF Set Debug Mode On Or Off 9 BEEP ON/OFF Set Onboard Beep On Or Off 0 LCD ON/OFF Set LCD Always On Or Auto Turn Off In Power On State RESET Reset System To Default Setting(Should Type "Yes" To Confirm, "No" To Discard) 2 OUT xx ON/OFF Set OUTPUT:xx On Or Off OUT xx FR yy Set OUTPUT:xx From INPUT:yy OUT xx EH/ET Set OUTPUT:xx Use HDMI/HDBT EDID xx=[00]: All OUTPUT Port, [0...08]: OUTPUT Port yy=[0...08]: INPUT Port 5 EDID xx CP yy Set Input:xx EDID Copy From Output:yy 6 EDID xx DF zz Set Input:xx EDID To Default EDID:zz xx=[00]: All INPUT Port, [0...08]: INPUT Port zz=00: HDMI 080p@60Hz, Audio 2CH PCM zz=0: HDMI 080p@60Hz, Audio 5.CH PCM/DTS/DOLBY zz=02: HDMI 080p@60Hz, Audio 7.CH PCM/DTS/DOLBY/HD zz=0: HDMI 080i@60Hz, Audio 2CH PCM zz=0: HDMI 080i@60Hz, Audio 5.CH PCM/DTS/DOLBY zz=05: HDMI 080i@60Hz, Audio 7.CH PCM/DTS/DOLBY/HD zz=06: HDMI 080p@60Hz/D, Audio 2CH PCM zz=07: HDMI 080p@60Hz/D, Audio 5.CH PCM/DTS/DOLBY zz=08: HDMI 080p@60Hz/D, Audio 7.CH PCM/DTS/DOLBY/HD zz=09: HDMI K2K, Audio 2CH PCM zz=0: HDMI K2K, Audio 5.CH PCM/DTS/DOLBY zz=: HDMI K2K, Audio 7.CH PCM/DTS/DOLBY/HD zz=2: DVI 280x02@60Hz, Audio None zz=: DVI 920x080@60Hz, Audio None zz=: DVI 920x200@60Hz, Audio None zz=5: User EDID zz=6: User EDID 2 zz=7: GUI Download EDID 7 MXIR xx FR yy Remote RX:xx IR Output From Local IR in:yy xx=[00]: All Remote Rx IR Output, [0...08]: Remote Rx IR 9 8
10 Output yy=[0...08] Local IR In 8 MXIR GI (+-)xx Global All IR In Signal Gose To Which IR Output:xx xx=[0...08]: Remote HDBT Transmitter IR Output(reserve) xx=[09...6]: Local IR Output xx=[7...2]: Remote HDBT Receiver IR Output +: Add xx To Current Setting -: Remove xx From Current Setting 9 MXIR GO (+-)xx Global All Ir Out Signal From Which IR Input:xx xx=[0...08]: Remote HDBT Transmitter IR Input(reserve) xx=[09...6]: Local IR Input xx=[7...2]: Remote HDBT Receiver IR Input xx=[25]: Global All Ir In +: Add xx To Current Setting -: Remove xx From Current Setting 20 MXRS xx TO yy Local RS-22:xx Route To Remote HDBT:yy xx=[0...08]: Local RS-22(reserve) xx=[09]: Global RS-22 yy=[00]: Not Connect To Any RS-22 yy=[0...08]: Remote HDBT Transmitter(reserve) yy=[09...6]: Remote HDBT Receiver 2 MXSTA Print Matrix IR And RS-22 Connect State 22 AUD RX xx ORG Input Port:xx Use Orginal Receive HDMI/DVI Signal 2 AUD RX xx ANA Input Port:xx Embeded Analog L/R To HDMI/DVI Signal 2 AUD RX xx AUTO Input Port:xx Embeded Analog L/R When DVI Signal xx==[00]: All Input Port, [0...08]: Input Port 25 MUTE ON/OFF TX yy Set Output Audio:yy Mute On or Off yy=[00]: All Output Audio, [0...08]: Output Audio 26 AUD STA Print Input/Output Port Audio Setting State 27 NET DHCP ON/OFF Set Auto IP(DHCP) ON Or OFF 28 NET IP xxx.xxx.xxx.xxx Set IP Address 29 NET GW xxx.xxx.xxx.xxx Set Gateway Address 0 NET SM xxx.xxx.xxx.xxx Set Subnet Mask Address NET RB Set Network Reboot and Apply New Config!!! Global All IR In Global All IR In can be set to any specific IR output or all of the IR outputs. Global All IR Out Global All IR Out can be set from any specific IR output or all of the IR inputs. Global All IR In can be set to loop to Global All IR Out. Global RS-22 Routing GUI Control PC System: Microsoft Windows Operation System Installation The HDbaseT8x8Matrix controller provides green software. Simply copy the 8x8 HDMI Matrix Controller vx.x.exe to a PC which is connected to the the Matrix by RS22 COM or TCP to complete the installation. Preparation. Connect the PC and the Matrix by RS22 cable or UTP cable Global RS22 can be set to any of the RS22 ports, either the remote receiver side or the local side. 9 8
11 Set Video Input Souce 2. Power up the Matrix (It will take about 5 seconds to be ready with a Di beep sound ). Double click the 8x8 HDMI Matrix Controller vx.x.exe icon to run it Common information Each input can be from HDMI or HDBaseT chosen via the pop-up menu under each Input port. ) Choose HDMI, then the HDMI input will be enabled; the HDBT input will be disabled. 2) Choose HDBT, then the HDBT input will be enabled; the HDMI input will be disabled. ) Choose Auto, the input will auto-scan the inputs between HDMI and HDBT. For example, if Input chooses HDBT and Auto, the input will auto-scan from HDBT to HDMI, if the HDBT input has a signal detected, the input will stay HDBT if not, it will scan the HDMI input and stay there when the signal detected. Set Audio Source for Input Click to select tab page COM port or TCP connect status 2 Control command process status Prompt message display area Date and Time display General page Each input audio source can be from the original HDMI/HDBT input, analog L/R embedded or Analog embedded DVI. ) Choose original, the audio will be from the HDMI/HDBT input. 2) Choose Analog L/R In embedded, the local L/R In will remove the original audio from the HDMI/HDBT input and embed the L/R audio. ) Choose Analog embedded when DVI, when a DVI signal is detected, it will embed the L/R audio. Note: Only PCM audio can be converted to analog audio output. Remote HDBT Receiver IR Output Control This provides the flexibility to change the IR path from the local IR in to the IR output of each Remote HDBT receiver. The default setting is each local IR in to the IR output of corresponding remote HDBT receiver. For example: Local IR in to IR output of the remote HDBT receiver and local IR in 8 to the IR output of remote HDBT receiver 8. Select control mode: RS22 COM mode (Auto COM ports detected) or TCP mode 2 List detected COM ports List all Matrix devices after search operation Click to search all Matrix devices that connected in same subnet 5 Click to configuration the selected Matrix s TCP control configurations 6 Click to connect or disconnect PC and Matrix ( Connection will be established automatically before control commands sending ) 7 Click to refresh device status: include device information displayed in 9 area and Input/output port connection status in 0 area. 7 0
12 NOTE: Tab pages cannot be changed while control commands are processing. 8 To enable or disable Input/output tags displayed on the Settings page focused 9 Device information display area 0 Input/output port connection status Set TCP control configuration Click the Config button to show the TCP configuration window. FW upgrade page Set the tag to identify the Matrix device 2 Set the IP mode: Subnet should support DHCP protocol when set to Auto IP mode, then the Matrix will obtain the IP automatically. Otherwise, set to Static IP mode and designate a useable IP for the Matrix Set the IP address, not editable when the Auto IP mode is selected. Note: The last IP BYTE s range is Matrix device MAC address 5 Click OK to set the configuration. If the configuration is set to OK, the Matrix will be searched out again 6 Click to Close the window and configuration will be cancelled Port Tag page Click to open the firmware file (file extension is.fw ). 2 Firmware upgrade progress bar Click the button to upgrade the firmware. Firmware upgrading messages will be displayed 5 Click to clear the messages displayed in the memo box. NOTE: If failure occurs during upgrading process, the following steps SHOULD be completed sequentially to establish the next upgrade procedure: ) Power down the Matrix 2) Close the 8x8 HDMI Matrix Controller ) Re-power up the Matrix, then wait for 0 seconds to ensure the Matrix is ready ) Run the 8x8 HDMI Matrix Controller, open firmware file and upgrade again 5 2 Input port tags 6
13 EDID control page Click to edit the Input port tags Output port tags Click to edit the Output port tags NOTE: ) Edit boxes are read only, click the Edit button and click the pop up window to edit the tags. 2) One set of Input/output port tags can be set for the Matrix device when the COM control mode is selected. ) Input/output port tags can be set for respective Matrix devices according to device s MAC address Edit Input port tags After editing the port tags 2, the window should look like this: Set the EDID mode for the selected Input port or All Input ports, click Set button to complete action. NOTE: When setting the User/User2 EDID mode, you should download the EDID content to User Memory/User2 Memory first. The User/User2 default EDID content is 080p, Stereo Audio Copy EDID from Output port to selected Input port or All Input ports, click the Copy button to complete the action. Read EDID content from Output port and display in the grid, click the Read button to complete the action. Save the EDID content which is displayed in the grid to a binary file (file extension is.bin ) 5 Open the EDID binary file and display in the grid 6 Download the EDID content which is displayed in grid to selected the Input port or All Input ports, click the Download button to complete the action. When the User Memory/User2 Memory is selected, download the EDID content to the respective memory then set the User/User2 EDID mode. 7 EDID content display grid NOTE: The EDID content displayed in the grid is read only. 8 Click to clear the EDID content displayed in the grid Define the tags for each respective Input port, then each device can be easily remembered. Click the button to delete a tag, if a tag is still being used by any other Input port, the delete action will be discarded. Edit Output port tags After editing the output port tags, the window should look like this: IR Configuration page To enable or disable the IR control function. When the box is checked, the IR control function is enabled; otherwise, the IR control function will be disabled. This setting is not memorized. The IR control function is always enabled after power up. Define the tags for each respective Input port, then each device can be easily remembered Click the button to delete a tag, if a tag is still being used by any other output port, the delete action will be discarded. 5 2
14 Settings page Pop-up Menu When the mouse cursors over the 2 setting buttons right click the mouse and the menu will popup like this The LED displays the Input number for the respective Output port 2 Click to select the Input port for the respective Output port Click to select the previous or next Input port for the respective Output port Displays the Output from Input with tag information when mouse cursors over 2 buttons 5 Pre-Set items: Default is Port to Port 6 Click to edit selected pre-set item 7 Set selected pre-set item to the Matrix NOTE: When you make changes to the Settings page, the software will try to refresh the source selection status of each Output port. Pop-up tag messages When the Display Input, Output tags setting buttons are on The General page is checked and the Input/output port tag has been defined, tag messages will pop up like this: All Outputs: All Outputs from same Input Output to 7 Outputs : Set the current Output (right click the mouse) and the next x- ( x range is from to 7, set total x Outputs at the same time all Output(s) from the same Input Port to Port: Output from Input, Output2 from Input2, Output from Input, etc. Edit the selected pre-set After action of 6, the edit form will pop-up as below: 2 Pre-Set name 2 Set all Output ports from the same Input Select the Input for the respective Output
HDTVMT User Manual
HDTVMT0808140 User Manual HDTV Supply, Inc. Contact: support@hdtvsupply.com 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More informationMT0404-A40 User Manual
MT0404-A40 User Manual HDTVSupply,Inc. Contact:sales@hdtvsupply.com.com 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting,
More informationHD-1X4-4K User Manual
HD-1X4-4K User Manual Factor Electronics. Contact: info@factorelectronics.com 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More informationHDBaseT / HDMI Splitter 1x4 User Manual
User Manual 875240 HDBaseT /HDMI Splitter 1x4 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting
More informationHDTVMT0404VL1 User Manual
HDTVMT0404VL1 User Manual HDTVMT0404VL1 User Manual Contact: support@hdtvsupply.com 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully
More informationHDTVMT0808VF2 User Manual
HDTVMT0808VF User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please
More informationLT1102-HDS User Manual. LT1102-HTS User Manual
LT1102-HTS User Manual 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please
More informationHDbaseT/HDMI/Audio Matrix 4x4 Manual
875760 HDbaseT/HDMI/Audio Matrix 4x4 Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting
More informationOperation instruction. HDMI Matrix. Operating Instruction
HDMI Matrix Operating Instruction Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product.
More informationHDBaseT/HDMI/Audio Matrix Manual
875770 HDBaseT/HDMI/Audio Matrix Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this
More informationHDMI Matrix Operating Instruction
1 HDMI Matrix Operating Instruction Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product.
More informationUser Manual TLS HDMI Switch Splitter 3/2
875224 User Manual TLS HDMI Switch Splitter 3/2 IR SW B A 3 2 1 HDMI IN HDMI OUT DC 5V 1 2 3 A B 8 875224 HDMI Switch Splitter 3/2 Thank you for purchasing this product. For optimum performance and safety,
More informationFactor HDBaseT-Balun Kit
Factor HDBaseT-Balun Kit 6G HDMI over HDBaseT TX/RX Kit w/ Audio Breakouts 4159 McConnell Drive Burnaby B.C. Canada V5A-3J7 Toll free 855-204-1388 1 Thank you for purchasing this product. For optimum performance
More information4x4 4K HDBaseT Matrix HMXL44AB. User Manual
4x4 4K HDBaseT Matrix HMXL44AB User Manual Contents Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting
More information4x4 4K HDMI 2.0 Matrix - HDCP 2.2 MX44AB-V2. User Manual
4x4 4K HDMI 2.0 Matrix - HDCP 2.2 MX44AB-V2 User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating
More informationHMXL66. User Manual HMXL66. Menu Up Esc All. Out EDID. In 6x6 4K HDBaseT Matrix PTP. Select Down Enter. IR Output.
IR Power 1 2 3 4 5 6 All Menu Up Esc Out EDID In 6x6 4K HDBaseT Matrix Lock 1 2 3 4 5 6 PTP Select Down Enter TCP/IP RS232 HMXL66 IR Input IR Output IR Ext. HDBT Ouput 0 1 EDID POH 24V Power 12V On/Off
More information4x4 4K HDBaseT Matrix - HDCP 2.2. HMXL44-KIT V2 User Manual
4x4 4K HDBaseT Matrix - HDCP 2.2 HMXL44-KIT V2 User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating
More informationSURGE PROTECTION DEVICE RECOMMENDED
4x4 HDMI2.0 Matrix Support 4K@60hz YUV4:4:4, 18Gbps, HDR Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More information4x4 HDMI2.0 Matrix Support YUV4:4:4, 18Gbps, HDR. Operating Instruction
4x4 HDMI2.0 Matrix Support 4K@60hz YUV4:4:4, 18Gbps, HDR Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More information8x8 HDMI2.0 Matrix Support YUV4:4:4, 18Gbps, HDR. Operating Instruction
8x8 HDMI2.0 Matrix Support 4K@60hz YUV4:4:4, 18Gbps, HDR Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More informationWebsite: Toll Free: [US] USER MANUAL
Website: www.jtechdigital.com Toll Free: 1-888-610-2818[US] Email:Support@jtechdigital.com USER MANUAL J-Tech Digital ProAV HDMI2.0 8X8 matrix with IP RS232 Coaxial RoHS JTD-ID:279 1 Thank you for purchasing
More informationWebsite: Toll Free: [US] USER MANUAL
Website: www.jtechdigital.com Toll Free: 1-888-610-2818[US] Email:Support@jtechdigital.com USER MANUAL J-Tech Digital ProAV HDMI2.0 8X8 matrix with IP RS232 Coaxial RoHS JTD-ID:279 1 Thank you for purchasing
More informationMX44AB. User Manual. 4x4 4K HDMI Matrix
MX44AB User Manual 4x4 4K HDMI Matrix MX44AB USER MANUAL Contents Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting,
More informationHDMI Matrix. Operating Instruction
HDMI Matrix 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this
More informationSM-4X4-4K18GB-LC. Low Cost 4K HDMI Video Matrix Switch: 4x4. Operating Instruction
SM-4X4-4K18GB-LC Low Cost 4K HDMI Video Matrix Switch: 4x4 Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More informationSM-4X4-4K18GBA-LC. 4x4 HDMI2.0 Matrix Support YUV4:4:4, 18Gbps, HDR. Operating Instruction
SM-4X4-4K18GBA-LC 4x4 HDMI2.0 Matrix Support 4K@60hz YUV4:4:4, 18Gbps, HDR Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions
More informationXT-HDBT-MX44-4K-KIT. Introduction. User Manual. Key Features XT-HDBT-MX44-4K-KIT USER MANUAL
XT-HDBT-MX44-4K-KIT User Manual Introduction Our XT-HDBT-MX44-4K-KIT 4x4 HDBaseT Matrix offers unprecedented performance and value for the custom installation market. The XT- HDBT-MX44-4K-KIT is a 4K HDCP
More informationSM-8X8-4K18GB-LC. Low-Cost 4K HDMI Video Matrix Switch: 8x8. Operating Instruction
SM-8X8-4K18GB-LC Low-Cost 4K HDMI Video Matrix Switch: 8x8 Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
More informationEX40B-KIT User Manual
CAT CAT Input Output Link IR RX IR TX Link IR RX IR TX EX40B-KIT User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting,
More informationHEX70ED-KIT-V2 User Manual
Transmitter RX RS232 HDMI In Link HDMI Out Link Rx IR Tx HEX70ED-RX-V2 EDID L/R Coaxial Out Link HDBT Out Power DC 12V HEX70ED-TX-V2 RS232 HDMI Out HDMI LINK IR RX IR TX HEX70ED-KIT-V2 User Manual Thank
More informationHEX70B-RX/-TX User Manual
HEX70B-RX/-TX User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please
More informationDV-HDA-14AUD 1x4 HDMI Distribution Amplifier Manual
DV-HDA-14AUD 1x4 HDMI Distribution Amplifier Manual Based on firmware 1.06 244 Bergen Blvd Woodland Park NJ 07424 973-785-4347 www.fsrinc.com 43226 LIT1573A PROPRIETARY INFORMATION All information in
More informationHSP14AB. User Manual. 70m 4-Way HDBaseT Splitter
HSP14AB User Manual 70m 4-Way HDBaseT Splitter Introduction Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating
More informationHEX70B-RX/-TX User Manual
HEX70B-RX/-TX User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please
More informationHDMI Matrix. Model: HDMIMX44RS. Operating Instruction
HDMI Matrix Model: HDMIMX44RS Operating Instruction 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or
More informationEL-4KPM-V88-A2416 Video/Audio Premium Matrix
IR Power 1 2 3 4 5 6 7 8 All Menu Up Esc Out EDID In Lock 1 2 3 4 5 6 7 8 PTP Select Down Enter EL-4KPM-V88-A2416 PlatinumMatrix HDBT In HDBT In TCP/IP Ethernet On/Off Global IR In IR Out 1 2 3 4 5 6 7
More informationDV-HDA-12AUD 1x2 HDMI Distribution Amplifier Manual
DV-HDA-12AUD 1x2 HDMI Distribution Amplifier Manual Based on firmware 1.03_20150928 244 Bergen Blvd Woodland Park NJ 07424 973-785-4347 www.fsrinc.com 43225 LIT1572B PROPRIETARY INFORMATION All information
More informationCMR Quick Start Guide. CMR-8500 DVB IP Encapsulator. Part Number MN-CMR68500-QSG REV. 1
CMR-8500 Quick Start Guide CMR-8500 DVB IP Encapsulator Part Number MN-CMR68500-QSG REV. 1 Copyright Comtech EF Data, 2008. All rights reserved. Printed in the USA. Comtech EF Data, 2114 West 7th Street,
More informationIR Out IR Out IR Out IR Out IR In IR In IR In IR In RS HDMI In HDMI In HDMI In HDBT Out HDMI Out HDBT Out HDBT Out HDBT Out C44-KIT.
4x4 4K HDBaseT Matrix - HDCP 2.2 Output 1 Output 2 Output 3 Output 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 Power IR 1 2 3 4 1 2 3 4 IR Out IR Out IR Out IR Out IR In IR In IR In IR In RS- 232 EDID HDMI In HDMI
More informationCustom Pro Matrix Solution User Manual
Lock 1 2 3 4 5 6 7 8 PTP C U S T O M P R O IR Power 1 2 3 4 5 6 7 8 All Menu Up Esc Out EDID In Select Down Enter Platinum 4K HDBaseT Matrix 1 2 3 4 5 6 7 8 TCP/IP RS232 L/R In Audio Out 1 Audio Out 2
More information4-Way 4K HDMI 2.0 Splitter SP14 -V2 DC 5V. Update. SP14-V2 User Manual
Power Input Output 1 Output 2 Output 3 Output 4 4-Way 4K HDMI 2.0 Splitter SP14 -V2 Update Input Output 1 Output 2 Output 3 Output 4 DC 5V SP14-V2 User Manual Contents Thank you for purchasing this product.
More informationANI-11X2MFS. UHD Multi-Format Video Presentation Scaler Switch w/ Audio INSTRUCTION MANUAL
ANI-11X2MFS INSTRUCTION MANUAL UHD 4K2K@30Hz Multi-Format Video Presentation Scaler Switch w/ Audio A-NeuVideo.com Frisco, Texas 75034 (469) 277-7606 AUDIO / VIDEO MANUFACTURER SAFETY INFORMATION 1. To
More information1x2 HDMI Splitter over Cat.X with HDBaseT-Lite, 4K2K, IR & RS-232
SP-5012V 1x2 HDMI Splitter over Cat.X with HDBaseT-Lite, 4K2K, IR & RS-232 User Manual rev: 140806 Made in Taiwan Safety and Notice The SP-5012V 1x2 HDMI Splitter over Cat.X with HDBaseT-Lite, 4K2K, IR
More information4x4 Seamless HDMI matrix & 2x2 Video Wall Controller
4x4 Seamless HDMI matrix & 2x2 Video Wall Controller Operating Instructions Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully
More informationEL-4KM-V44-KIT. User Manual EL-4KM-V44 EDID. HDMI IR Ext. HDBT Output 4 HDMI HDMI HDMI. Menu Up Esc All. Out. Out EDID.
IR Power 2 3 4 All Menu Up Esc IR Power Out 2 3 4 All Menu Up Esc Out In VideoMatrix VideoMatrix Lock Lock In 2 3 4 2 3 4 PTP PTP Select Down Enter Select Down Enter 32 0 0 2 3 4 2 3 4 IR Input IR Output
More informationLink. Coaxial HDMI Output L/R Out Out Upgrade. Mode. DC 5V Power Link. L/R In HDMI Input EDID SC11HD-V2. User Manual
Mode Coaxial HDMI Output L/R Out Out Upgrade DC 5V Power 3 2 L/R In HDMI Input EDID SCHD-V2 User Manual SCHD-V2 USER MANUAL Thank you for purchasing this product. For optimum performance and safety, please
More informationUser Manual rev: Made in Taiwan
SP-5022V 1x2 HDMI Splitter/Repeater over Cat.X with HDBaseT-Lite, 4K2K & local Out User Manual rev: 140212 Made in Taiwan The SP-5022V 1x2 HDMI Splitter/Repeater over Cat.X with HDBaseT-Lite, 4K2K & local
More informationEL-4KHDBT-TXRX-40-IRS
EDID Mode L/R Coaxial Out Link HDBT Out TX Power EL-4KHDBT -TX-40-IRS EDID Mode L/R Coaxial Out Link HDBT Out TX Power EL-4KHDBT -TX-40-IRS IR RX IR TX RS-232 HDMI In Link HDMI Out Link EL-4KHDBT-RX-40-IRS
More informationPLATINUM MATRIX SOLUTIONS
Lock PLATINUM MATRIX SOLUTIONS HDBT In HDBT In TCP/IP Ethernet On/Off Global IR In IR Out 1 2 3 4 5 6 7 8 IN OUT 1 2 3 4 5 6 7 8 In PLA88ARC V2 PLA88L V2 PLA66ARC V2 EL-4KPM-V88-A2416 PlatinumMatrix PLA66L
More informationLBC-HDV-T LINK BRIDGE TM HDBASET HDMI/DISPLAYPORT/VGA TRANSMISSION SYSTEM
LBC-HDV-T LINK BRIDGE TM HDBASET HDMI/DISPLAYPORT/VGA TRANSMISSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed
More informationLBS-42H2 LINK BRIDGE TM 4x2 HDMI 2.0 Matrix Switcher
LBS-42H2 LINK BRIDGE TM 4x2 HDMI 2.0 Matrix Switcher BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of their
More informationHDTV Supply, Inc. Operating Instructions
HDTV Supply, Inc. Operating Instructions Thanks for purchasing our product. Please be sure to read this instruction manual Carefully before using our product. User Manual Table of Contents Quick Start
More informationAC-DA210-HDBT. Operation Manual
AC-DA210-HDBT HDBaseT 2-8-2 splitter with Audio De-Embedding, EDID Management, and switchable inputs. Operation Manual 1 Revision History VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGES RDV1 08/10/16 Preliminary
More informationHDMI Extender over Ethernet
HDMI Extender over Ethernet Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this
More informationHDMI Extender over Ethernet, with RS232, POE
WARRANTY If your product does not work properly because of a defect in materials or workmanship, our Company (referred to as "the warrantor" ) will, for the length of the period indicated as below, (Parts(2)Year,
More informationMX-5004MZ. User Manual. 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4. rev: Made in Taiwan
MX-5004MZ 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4 User Manual rev: 160318 Made in Taiwan Safety and Notice The MX-5004MZ 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4 has
More informationOperating Instructions
Model No ZIG-CX-100 Operating Instructions Thank you for purchasing this product. Please be sure to read the instruction manual carefully. Introduction The ZIGEN ZIG-CX-100 is a transmitter / receiver
More information8X8 HDBaseT Lite Matrix with PoC, HDCP2.2 & 4K2K60 (YUV420) User Manual. rev: Made in Taiwan
MA-5488V2 8X8 HDBaseT Lite Matrix with PoC, HDCP2.2 & 4K2K60 (YUV420) User Manual rev: 151209 Made in Taiwan Safety and Notice The MA-5488V2 8x8 HDBaseT Lite matrix with PoC, HDCP2.2 & 4K2K60 (YUV420)
More informationSP x4 DVI over Single CAT5 Distribution Amplifier. User Manual. Made in Taiwan
SP-1014 1x4 DVI over Single CAT5 Distribution Amplifier User Manual Made in Taiwan Safety and Notice The SP-1014 1x4 DVI over Single CAT5 Distribution Amplifier has been tested for conformance to safety
More information1x8 HDMI Splitter Over Single Cat5e/6 Cable. Up to 50M with IR. Notice. Features. Package Contents. Operating Instructions
1x8 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR Operating Instructions Notice The information in this document is subject to change without notice. Every effort has been made in the preparation
More informationCEX120B-KIT User Manual
HDMI In Coax Input CEX120B-TX CEX120B-RX Coax Output OFF HDMI Out ON MODE CEX120B-KIT User Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions
More information1x4 HDMI & Full 3D support over Single CAT5 Distribution Amplifier with Local Output. User Manual
SP-5105KC 1x4 HDMI & Full 3D support over Single CAT5 Distribution Amplifier with Local Output User Manual To avoid EMI issue, complete STP Cat6 cable is strongly recommended! rev: 131028 Made in Taiwan
More informationUser Manual rev: Made in Taiwan
SP-1014 1x4 DVI Splitter over Single Cat.X with HDCP Support User Manual rev: 111209 Made in Taiwan The SP-1014 1x4 DVI Splitter over Single Cat.X with HDCP Support has been tested for conformance to safety
More informationHDBaseT Extender Over Single Cat5e/6 cable Model: SX-EX33 Operating Instructions
HDBaseT Extender Over Single Cat5e/6 cable Model: SX-EX33 Operating Instructions Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions
More informationHDMI 1.3 Matrix Switch Receiver over CAT5 with IR Pass-Through
HDMI 1.3 Matrix Switch Receiver over CAT5 with IR Pass-Through Model #: HDMI-C5SW-R 20010 Avenview Inc. All rights reserved. The contents of this document are provided in connection with Avenview Inc.
More informationBRIGHTLINK 1x8 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR MODEL: BL-SPL1X8-CAT
BRIGHTLINK 1x8 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR MODEL: BL-SPL1X8-CAT Notice The information in this document is subject to change without notice. Every effort has been made in
More informationOperating Instructions. 70M HDBaseT Extender Over Single Cat5e/6 cable
70M HDBaseT Extender Over Single Cat5e/6 cable 70M HDBaseT Extender Over Single Cat5e/6 cable Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these
More informationMeichengR SP-5018M. 2x8 HDMI 1.3 over Single CAT5 Matrix Switcher. User Manual
MeichengR SP-5018M 2x8 HDMI 1.3 over Single CAT5 Matrix Switcher User Manual Safety and Notice The SP-5018M 2x8 HDMI 1.3 over Single CAT5 Matrix Switcher has been tested for conformance to safety regulations
More informationUSER MANUAL. DV-HAS HDMI Audio Separator LIT Bergen Boulevard, Woodland Park, NJ Tel FAX Web:
USER MANUAL DV-HAS HDMI Audio Separator 244 Bergen Boulevard, Woodland Park, NJ 07424 Tel 973-785-4347 FAX 973-785-3318 Web: www.fsrinc.com LIT1460 Proprietary Information All information in this manual
More informationBRIGHTLINKAV.COM. BRIGHTLINK 1x2 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR Model: BL-SPL1X2-CAT
BRIGHTLINK 1x2 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR Model: BL-SPL1X2-CAT BRIGHTLINKAV.COM Notice The information in this document is subject to change without notice. Every effort
More informationMX User Manual. Dual-View Video Processor. rev: Made in Taiwan
MX-5022 Dual-View Video Processor User Manual rev: 151210 Made in Taiwan Safety and Notice The MX-5022 Dual-View Video Processor has been tested for conformance to safety regulations and requirements,
More informationHDMI 16 by 16 Matrix Switcher
HDMI 16 by 16 Matrix Switcher AT-HD-V1616M User Manual Table of Contents 1. Introduction... 3 2. Package Contents... 3 3. Features... 3 4. Specifications... 4 5. Control and Functions a. Front Panel...
More informationMA-5444V2. User Manual. 4X4 HDBaseT Lite Matrix with PoC, HDCP2.2 & 4K2K60 (YUV420) rev: Made in Taiwan
MA-5444V2 4X4 HDBaseT Lite Matrix with PoC, HDCP2.2 & 4K2K60 (YUV420) User Manual rev: 151209 Made in Taiwan Safety and Notice The MA-5444V2 4x4 HDBaseT Lite matrix with PoC, HDCP2.2 & 4K2K60 (YUV420)
More informationUser Manual SP-5028E. 2x8 HDMI Splitter 7.1 CH AUDIO. rev: Made in Taiwan
User Manual SP-5028E 2x8 HDMI Splitter To avoid EMI issue, complete STP Cat6 cable is strongly recommended! 7.1 CH AUDIO rev: 110225 Made in Taiwan Safety and Notice The SP-5028E 2x8 HDMI Splitter has
More informationOperating Instructions
Model No.: SX-MX08 Operating Instructions Thanks for purchasing our product. Please be sure to read this instruction manual Carefully before using our product. Introduction Foxun s SX-MX08 is a HDMI2.0
More informationHDMI Extender over Cat5e/6
Statement Thanks for purchasing this product, please read this user manual carefully before using this product.in the constant effort to improve our product, we reserve the right to make functions or parameters
More informationLBC-HDBT-R-DG LINK BRIDGE TM HDBASET HDMI RECEIVER W/POH
LBC-HDBT-R-DG LINK BRIDGE TM HDBASET HDMI RECEIVER W/POH BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of
More informationUSER MANUAL.
HD4X4LITE USER MANUAL www.mstrbrand.com SAFETY & NOTICE The 4x4 HDBaseT Lite matrix with PoC has been tested for conformance to safety regulations and requirements, and has been certified for international
More information2x16 HDMI Splitter with 1 UTP input, Support 4K, Audio Extraction, EDID
2x16 HDMI Splitter with 1 UTP input, Support 4K, Audio Extraction, EDID Operating Instructions Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these
More information2x2 HDMI Splitter with 1 UTP input, Support 4K, Audio Extraction, EDID
2x2 HDMI Splitter with 1 UTP input, Support 4K, Audio Extraction, EDID Operating Instructions Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these
More informationMA-5544H. User Manual. 4X4 HDMI 2.0a Matrix. rev: Made in Taiwan
MA-5544H 4X4 HDMI 2.0a Matrix User Manual rev: 161116 Made in Taiwan Safety and Notice The MA-5544H 4x4 HDMI 2.0a matrix has been tested for conformance to safety regulations and requirements, and has
More information4K 7x1 Multi-format Presentation Switcher DV-MFSS-71
4K 7x1 Multi-format Presentation Switcher DV-MFSS-71 Based on firmware revision 1.11 and FSR1.0.0.L 244 Bergen Blvd Woodland Park NJ 07424 973-785-4347 www.fsrinc.com 43091 LIT1557 2 PROPRIETARY INFORMATION
More informationHDMI 16 by 16 Matrix Switcher
HDMI 16 by 16 Matrix Switcher AT-HD-V1616M User Manual atlona.com Table of Contents 1. Introduction... 3 2. Package Contents... 3 3. Features... 3 4. Specifications... 4 5. Control and Functions a. Front
More information4K-WALL HDMI/DVI Video Wall Controller and 4x4 Switch Matrix. User Manual
4K-WALL HDMI/DVI Video Wall Controller and 4x4 Switch Matrix. User Manual Integrated 2x2 Video Wall Controller and 4x4 Port HDMI, Real Time Switch Matrix with On Screen Display Control & No Software Required.
More information2x4 HDMI Splitter with 1 UTP input, Support 4K, Audio Extraction, EDID
2x4 HDMI Splitter with 1 UTP input, Support 4K, Audio Extraction, EDID Operating Instructions Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these
More informationHDMI 1.3 over Single CAT5 Extender
CV-57G HDMI 1.3 over Single CAT5 Extender User Manual Made in Taiwan Safety and Notice The CV-57G HDMI 1.3 over Single CAT5 Extender has been tested for conformity to safety regulations and requirements,
More informationUSER MANUAL. S3MBW HDMI Multi-format Extender Over CAT5e/CAT6. Back View. Front View. Covid Part Numbers
Front View Back View Covid Part Numbers Black Anodized: S3MBW-200-BA Clear Anodized: S3MBW-200-CA Antique White: S3MBW-200-AW Black PC: S3MBW-200-BL White PC: S3MBW-200-WH Table of Contents Introduction...2
More information1x4 Splitter HDMI Distribution Amplifier with 4K2K & HDCP Support
1x4 Splitter HDMI Distribution Amplifier with 4K2K & HDCP Support User s Guide Models PT-SP-HD14-4K Designed in Germany Made in Taiwan 2010 PureLink GmbH All rights reserved. www.purelink.de 1 Table of
More informationLBC-SPH8-1HB7-EIR LINK BRIDGE TM HDBASET 7X TRANSMISSION SYSTEM
LBC-SPH8-1HB7-EIR LINK BRIDGE TM HDBASET 7X TRANSMISSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result
More informationHDMI Extender (By single CAT-5E/6E cable)
HDMI Extender (By single CAT-5E/6E cable) Model No.EX0101-U57/U58 Operating Instructions(P/N of this Instructions is INSEX0101-U57/U58) FEATURES One pair as a full functional module, no need for setting.
More informationUser Manual rev: Made in Taiwan
SP-5002P3 HDMI 1.4 1x2 HDMI Splitter User Manual rev: 130130 Made in Taiwan The SP-5002P3 HDMI 1.4 1x2 HDMI Splitter has been tested for conformance to safety regulations and requirements, and has been
More informationover HDBaseT w/poe, IR & RS-232C
150 meter HDMI Extender over HDBaseT w/poe, IR & RS-232C Version 1.1 All rights reserved by KanexPro and changes may be added without any notification to the customer. Please look out for the latest update
More informationDVI over Single CAT5 Series CV-17. DVI over Single CAT5 Extender. User Manual. Made in Taiwan
DVI over Single CAT5 Series CV-17 DVI over Single CAT5 Extender User Manual Made in Taiwan Safety and Notice The CV-17 DVI over Single CAT5 Extender has been tested for conformance to safety regulations
More informationManual Guide PT-SP-HD18-4K. Manual Guide. 1x8 HDMI Distribution Amplifier with 4K2K & HDCP Support. Model PT-SP-HD18-4K. Designed in Germany
Manual Guide 1x8 HDMI Distribution Amplifier with 4K2K & HDCP Support Model Designed in Germany 2015 PureLink GmbH All rights reserved. Table of Contents Section 1: Getting Started... 2 1.1 Safety and
More informationInstallation Manual SM-RS Port RS232 Router with optional TCP/IP control
Installation Manual SM-RS232 16-Port RS232 Router with optional TCP/IP control Control up to 16 RS232 compliant devices up to 50 feet away over UTP or from anywhere via TCP/IP (optional) What s in the
More informationHDMI/HDBT 1x4 Splitter. Installation & Operation Manual. MuxLab Inc A / SE A
500424 MuxLab Inc. 2016 94-000808-A / SE-000808-A SAFETY PRECAUTIONS To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.
More informationZIG-DA14-UHD HDMI MHz HDMI Distribution Amplifier w/hdcp 2.2 & WebOS
ZIG-DA14-UHD HDMI 2.0 600 MHz HDMI Distribution Amplifier w/hdcp 2.2 & WebOS ZIG-DA14-UHD-UHD USER MANUAL Ver. 1.0 August 2015 Table of Contents Copyright and Trademark 3 Introduction 4 Package Contents
More informationLB-H2-E. Link Bridge 4K UHD + Audio Embedder
LB-H2-E Link Bridge 4K UHD + Audio Embedder BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of their use or
More informationSC35.MX HDMI 18Gbps Over HDBaseT Matrix VER 1.1
SC35.MX44 4 4 HDMI 8Gbps Over HDBaseT Matrix VER. Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting
More informationTEK-MHD44TP x4 HDMI Matrix with HDBaseT Lite Outputs
TEK-MHD44TP 79055 4x4 HDMI Matrix with HDBaseT Lite Outputs TEK-TPHD402PR User s Manual December 30, 2013 Please read this manual carefully before using the system. Attention: This manual only includes
More information