LBC-HDV-T LINK BRIDGE TM HDBASET HDMI/DISPLAYPORT/VGA TRANSMISSION SYSTEM

Size: px

Start display at page:

Download "LBC-HDV-T LINK BRIDGE TM HDBASET HDMI/DISPLAYPORT/VGA TRANSMISSION SYSTEM"

Zoe Hubbard
5 years ago
Views:

1 LBC-HDV-T LINK BRIDGE TM HDBASET HDMI/DISPLAYPORT/VGA TRANSMISSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of their use or application. All rights reserved Broadata Communications, Inc.

2 SAFETY INSTRUCTIONS AND COMPLIANCE DECLARATIONS PLEASE OBSERVE THE FOLLOWING SAFETY PRECAUTIONS SURGE PROTECTION DEVICE RECOMMENDED This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Broadata Technical Support, 3

3 TABLE OF CONTENTS 1.0 PRODUCT DESCRIPTION OPERATION CONTROLS AND FUNCTIONS FRONT PANEL REAR PANEL DC POWER CONNECTION PHOENIX CONTACT CONNECTION WEB SERVER MAINTENANCE AND TROUBLESHOOTING MAINTENANCE TROUBLESHOOTING SPECIFICATIONS SERVICE PROCEDURE REPLACEMENT POLICY RETURN AND REPAIR SERVICE LIMITED WARRANTY APPENDIX A Broadata Technical Support, (800)

4 1.0 PRODUCT DESCRIPTION The LBC-HDV-T is a multi-format switcher with HDMI, VGA and DisplayPort inputs to HDBT output. The audio port is independent and could be embedded into any of the video signals and send it to the far end. The product supports webserver and can be controlled by the button, LAN, RS-232, contact closure, IR and RS-232 can pass through. Features Switch and extend HDMI, DisplayPort or VGA signals up to 70 meters over CAT-5e/6 HDTV video resolutions up to 720p/1080i/1080p@60Hz or 1920x1200@60Hz, as well as Ultra HD (4K2K@30Hz) Fully uncompressed video with embedded audio provides zero loss of quality Selectable manual or auto-switching between HDMI, DisplayPort and VGA inputs Webserver for monitoring and configuation Manual switching through front-panel button, contact closure, RS-232 or webserver Video/Audio+Data over 1 CAT-5e/6 with true DDC/EDID/HDCP transmission Compatible with our LBH/LBC Series products Broadata Technical Support, Sales@Broadatacom.com 5

5 2.0 OPERATION CONTROLS AND FUNCTIONS 2.1 Front Panel HDMI D H V PWR LINK SELECT PWR: Solid red when powered on. 2. HDMI: LED solid when the HDCP, flashing when without HDCP. 3. LINK: Flashing when HDBT connected without video signal, solid when video presented. 4. D: LED solid when DP selected, flashing when signal presented, off means no input signal. 5. H: LED solid when HDMI selected, flashing when signal presented, off means no input signal. 6. V: LED solid when VGA selected, flashing when signal presented, off means no input signal. 7. Button for switching input signal. 6 Broadata Technical Support, (800)

6 2.2 Rear Panel 24V DC HDBT VGA LAN D H V LD DP HDMI AUD OUT IN TX RX LV LH Power: 24V DC Power. 2. HDBT Out: HDBT output. 3. DP: DisplayPort input. 4. HDMI: HDMI input. 5. VGA: VGA input. 6. AUD: Independent audio input 7. LAN: LAN for local control or web serve access 8. Phoenix Port: RS-232 and Contact Closure with LED indicator Broadata Technical Support, Sales@Broadatacom.com 7

7 2.3 DC Power Connection Congratulations! You are now ready to power up the LBC-HDV-T and set up your network connection. In order to make sure that you have a proper installation, please observe the following: 1. Your AC jack has power. 2. The 24VDC power supply is working. 3. Your electrical system has proper grounding (this ensures that your power supply does not suffer from voltage variations). 4. Power Surge Protection. This is optional, but highly recommended. A UPS system provides voltage regularity as well as prevents spikes from occurring, thus protecting your LBC-HDV-T from sensitive voltage conditions. The LBC-HDV-T derives power from an external 24VDC power supply. This power supply is a wall mounted AC/DC adapter, VAC, Hz, at 1A. This power supply comes standard for the LBC-HDV-T unless otherwise specified. If you have any problems or concerns, regarding the installation, make sure that you have taken the proper steps to ensure a proper power connection. Otherwise, feel free to contact us for any questions you may have. 8 Broadata Technical Support, (800)

8 3.0 PHOENIX CONTACT CONNECTION GND D H V LD D H V LD TX RX TX RX GND LV LH LV LH Note: V: VGA Input LV: LED indicator for VGA D: DP Input LD: LED indicator for DP H: HDMI Input LH: LED indicator for HDMI TX: RS-232 Tx RX: RS-232 Rx GND: Ground Broadata Technical Support, Sales@Broadatacom.com 9

4.0 WEB SERVER The factory default IP: 192.168.2.175 Note: BCI product configuration program can be used to discover unit s IP address.

9 4.0 WEB SERVER The factory default IP: Note: BCI product configuration program can be used to discover unit s IP address. To access the product web server, user candirect connect the PC LAN port to the LBC-HDV-T LAN port with a straight RJ-45 cable. After making the connection, go to network connection of the PC and revise the IP property to static IP as below. Once done, open a web browser and enter the to access the web server. For the LBC-HDV-T connection to the local area network, please update the LBC-HDV-T IP to match the LAN network setting from the web server. For example, if the LAN IP is set as xxx. Once the IP is set, then you can access to the device from an PC in the same network. 10 Broadata Technical Support, (800)

Input/Output Configuration This page provides the switching, connection input signal information, and the HDBT output connection status. AV Inputs: Select to switch the input.

10 Input/Output Configuration This page provides the switching, connection input signal information, and the HDBT output connection status. AV Inputs: Select to switch the input. Auto Switch Video: If checked, the device is set in auto switching mode rather than manual mode. External Audio: If checked, the 3.5mm audio input is embedded to the input video. Input Config: Input port information. Output Config: HDBT connection status. Active Input: Showing the input signal format and resolution. Active Output: Showing output signal format and resolution. HDCP Unauthorized: When checked, LBC-HDV-T will request no HDCP compliant source. Broadata Technical Support, 11

11 EDID Management This page provides switching and EDID management. Follow Output: EDID from display. Broadata EDID: Internal preload EDID 12 Broadata Technical Support, (800)

12 RS-232 Configuration RS-232: Local RS-232 setting to control the LBC-HDV-T. HDBT RS-232: Set the far end RS-232 baud rate. RS-232 Preset Command 1: When detecting active signal, sends the RS-232 command in the preset timing. Command 2: When no active signal present, sends the command in the preset timing. Button: Press and hold the button for 3-5 seconds, sends the preset command. To set the preset RS-232, click the program button to program the code to the unit. Note: See Appendix A for RS-232 Command Table. Broadata Technical Support, Sales@Broadatacom.com 13

13 System System and firware information. User can modify the IP setting on this page. Remember to click on Apply for the changes. 14 Broadata Technical Support, (800)

14 5.0 MAINTENANCE AND TROUBLESHOOTING 5.1 Maintenance There is no operator maintenance other then keeping the units clean. However, observe the following light indicators to make sure that the unit is working properly: 5.2 Troubleshooting If the LBC-HDV-T units do not operate properly after installation, check for possible cable breaks, loose connections, and incorrect cable connections. If problems persist that may be fiber related, contact BCI at for further assistance. For electrical problems, perform the following troubleshooting procedures: 1. If the POWER indicator is OFF, check for the following: a. The line cord is plugged into the unit and your outlet has power. 2. If the POWER indicator is ON, but the Link indicator is OFF, check for the following: a. Make sure the appropriate cables are being used. b. Cable and cable connectors are not broken. c. For each unit, the transmit (TX) cable is connected to the other unit s receiver (RX). 3. If the POWER indicator and Link indicator are ON, but the channels are not operating, then: a. Check to see that the attached user equipment is turned on. b. Both ends of the link are connected to the corresponding equipment and to the same corresponding channel port. Broadata Technical Support, Sales@Broadatacom.com 15

15 c. Cable connections at both channels are securely fastened to each connector. Turn the power off, then back on to reset the link. 16 Broadata Technical Support, (800)

16 6.0 SPECIFICATIONS Video Resolution Connectors Protocol Audio Channel Capacity Operating Mode Connector (HDMI) up to (DisplayPort) up to (VGA) up to HDMI, DisplayPort, and VGA Female Plug DDC/EDID/HDCP Capable 1 L/R Analog Unbalanced (Stereo Audio) 3.5mm Stereo Jack Control Channel Capacity 1 Signal Format RS-232 or Ethernet Data Rate 19.2k baud (RS-232) Connector Terminal Block (RS-232), RS-45 (Ethernet) HDBaseT Link Cable Type CAT-5e/6 or higher Number of Cables 1 Connector/Distance RJ-45/Up to 70m Remote Powering 24VDC Physical Dimensions 2-Way 7.48 (W) x 4.12 (D) x 1.18 (H) Broadata Technical Support, Sales@Broadatacom.com 17

17 7.0 SERVICE PROCEDURE 7.1 Replacement Policy Standard products found defective on arrival (DOA) will be replaced, based on availability, within 24 to 48 hours anywhere in the U.S. Please call Customer Service at for information. 7.2 Return/Repair Service The LBC-HDV-T System contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/ repair processing please contact Broadata Communications, Inc. to obtain a Return Material Authorization (RMA). Please include the following information: Product model number Serial Number Complete description of problem Hardware installation description Broadata Communications, Inc West 237th Street, Suite K Torrance, CA (310) (310) (Facsimile) CustomerService@Broadatacom.com Website: 18 Broadata Technical Support, (800)

18 8.0 LIMITED WARRANTY Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of shipment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI s election, by replacement, any said products that in our sole discretion prove to be defective and are returned to the manufacturing location within 30 days after such defect is ascertained. All warranties are limited to defects arising under normal use and do not include malfunctions or failure resulting from misuse, abuse, neglect, alterations, electrical power problems, usage not in accordance with product instructions, improper installation, or damage determined by BCI to have been caused by the Buyer or repair made by a third party. Limited warranties granted on products are to the initial customer end-user and are not transferable. OUR LIABILITY UNDER THIS WARRANTY SHALL IN ANY CASE BE LIMITED TO THE INVOICE VALUE OF THE PRODUCT SOLD AND BCI SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE USE OF ITS PRODUCTS OR THE SALE THEREOF. We make NO WARRANTY AS TO THE MERCHANTABILITY OF ANY GOODS, OR THAT THEY ARE FIT FOR ANY PARTICULAR PURPOSE OR END APPLICATION NOR DO WE MAKE ANY WARRANTY, EXPRESSED OR IMPLIED OTHER THAN AS STATED ABOVE. Broadata Technical Support, Sales@Broadatacom.com 19

19 9.0 APPENDIX A: RS-232 COMMAND TABLE RS-232 Setting Protocol Command Example Baud Rate >MBaud:115200<0D 0A> #MBaud<0D 0A> Support 9600, (default) 38400, Data Bits >MDBits:8<0D 0A> #MDBits<0D 0A> Support 8 & 9 Stop Bits >MSBits:1<0D 0A> #MSBits<0D 0A> Support 1 & 2 Parity Bits >Mparity:None<0D 0A> #Parity<0D 0A> Support ODD, Even, None Network Setting DHCP >DHCP:ON<0D 0A> #DHCP <0D 0A> IP >IP: <0D 0A> #IP<0D 0A> Net Mask >Mask: #Mask<0D 0A> <0D 0A> Gateway >Gate: #Gate<0D 0A> <0D 0A> TCP >Tcp Protocol:Server #tcp Protocol Protocol <0D 0A> <0D 0A> TCP Port >tcp Port:1001<0D 0A> #Tcp Port<0D 0A> TCP Host >HsIP: #HsIP<0D 0A> IP <0D 0A> Video Switching Switching >C2to1<0D 0A> #C 1:DP 2:HDMI 3:VGA Output Port >V0<0D 0A> 1:Output On 0:Output Mute Query Resolution #R Switching Mode >M0<0D 0A> 1:Auto 0:Manual Auto Setting 0:Mute 1:Vol Up 2:Vol Down Audio >A1<0D 0A> 0:Internal Audio 1:External Audio Pass through (RS-232 >RS1TX05Hello<0D 0A> Command pass through (control port): to LAN or 1:RS232 2:LAN vice versa) Ex: passing command through RS-232 port 5 character Hello Note: The default baud rate Query Command Example Note 20 Broadata Technical Support, (800)

20 Broadata Technical Support, 21

21 22 Broadata Technical Support, (800)

22 60000-LBCHDVT Broadata Communications, Inc West 237th Street, Suite K Torrance, CA (310) (310) (Facsimile) CustomerService@Broadatacom.com Website:

LBC-PSW52. Link Bridge TM Presentation Scaling Switch with 5 Inputs and Two Mirrored Outputs

LBC-PSW52. Link Bridge TM Presentation Scaling Switch with 5 Inputs and Two Mirrored Outputs LBC-PSW52 Link Bridge TM Presentation Scaling Switch with 5 Inputs and Two Mirrored Outputs BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability