AOC-S3216L-L16iT USER S GUIDE. Revision 1.0

Transcription

1 O-S3216L-L16iT USR S GUI Revision 1.0

2 The information in this User's Guide has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this user's guide, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this user's guide, please see our Website at Super Micro omputer, Inc. ("Supermicro") reserves the right to make changes to the product described in this user's guide at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. ny use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license. IN NO VNT WILL SUPR MIRO OMPUTR, IN. B LIBL FOR IRT, INIRT, SPIL, ININTL, SPULTIV OR ONSQUNTIL MGS RISING FROM TH US OR INBILITY TO US THIS PROUT OR OUMNTTION, VN IF VIS OF TH POSSIBILITY OF SUH MGS. IN PRTIULR, SUPR MIRO OMPUTR, IN. SHLL NOT HV LIBILITY FOR NY HRWR, SOFTWR, OR T STOR OR US WITH TH PROUT, INLUING TH OSTS OF RPIRING, RPLING, INTGRTING, INSTLLING OR ROVRING SUH HRWR, SOFTWR, OR T. ny disputes arising between the manufacturer and the customer shall be governed by the laws of Santa lara ounty in the State of alifornia, US. The State of alifornia, ounty of Santa lara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. F Statement: This equipment has been tested and found to comply with the limits for a lass digital device pursuant to Part 15 of the F Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. alifornia Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing R (Manganese ioxide) Lithium coin cells. Perchlorate Material-special handling may apply. See WRNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of alifornia to cause birth defects and other reproductive harm. User's Guide Revision 1.0 Release ate: May 8, 2017 Unless you request and receive written permission from Super Micro omputer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. opyright 2017 by Super Micro omputer, Inc. ll rights reserved. Printed in the United States of merica

3 Preface Preface bout this User's Guide This user's guide is written for system integrators, IT technicians and knowledgeable end users. It provides information for the installation and use of the O-S3216L-L16iT controller card. bout this ontroller ard The Supermicro SS O-S3216L-L16iT internal controller card features sixteen internal SS3 ports with four internal mini SS H connectors. It utilizes a Broadcom SS3216 SS3 controller chip and features a 1.2 GHz processor. The O-S3216L-L16iT can provide support for JBO systems of up to 102 devices. The O-S3216L-L16iT is streamlined to meet the growing demand for increased data throughput and scalability requirements across the enterprise-class server platforms. It is a low power and cost-effective near-line storage solution that delivers maximum performance and reliability. n Important Note to the User ll images and layouts shown in this user's guide are based upon the latest PB revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this user's guide. iii

4 O-S3216L-L16iT ontroller ard User's Guide Returning Merchandise for Service receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered. You can obtain service by calling your vendor for a Returned Merchandise uthorization (RM) number. When returning the O-S3216L-L16iT card to the manufacturer, the RM number should be prominently displayed on the outside of the shipping carton, and the shipping package is mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete. For faster service, you can also request a RM authorization online This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alternation, misuse, abuse or improper maintenance of products. iv

5 Preface ontacting Supermicro Headquarters ddress: Super Micro omputer, Inc. 980 Rock ve. San Jose, U.S.. Tel: +1 (08) Fax: +1 (08) mail: (General Information) (Technical Support) Website: urope ddress: Super Micro omputer B.V. Het Sterrenbeeld 28, 5215 ML 's-hertogenbosch, The Netherlands Tel: +31 (0) Fax: +31 (0) mail: (General Information) (Technical Support) (ustomer Support) Website: sia-pacific ddress: Super Micro omputer, Inc. 3F, No. 150, Jian 1st Rd. Zhonghe ist., New Taipei ity 235 Taiwan (R.O.) Tel: +886-(2) Fax: +886-(2) mail: Website: v

6 O-S3216L-L16iT ontroller ard User's Guide Table of ontents Preface hapter 1 Overview 1-1 Overview Technical Specifications General OS Support Physical imensions hapter 2 Hardware omponents 2-1 ontroller ard Layout and omponents Major omponents onnectors and Ls SS onnectors Front Header Locations hapter 3 Installation 3-1 Static-Sensitive evices Precautions Unpacking Before Installation Installing the ontroller ard Static Sensitive evices Precautions Unpacking Installing the rivers in Windows Uninstalling the rivers vi

7 hapter 1: Overview hapter 1 Overview 1-1 Overview ongratulations on purchasing your controller card from an acknowledged leader in the industry. Supermicro products are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. For product support and updates, please visit our website at Technical Specifications General Broadcom SS3216 SS3 controller Sixteen internal SS3 ports 1.2 GHz processor HB supports 102 devices nlarged venting hole for improved airflow Plugs into PIe x8 slot to support Gen 3 up to 8Gb/s. Supports 12 GB/s, 6 GB/s and 3 GB/s SS data transfer rates. Supports 6 GB/s and 3 GB/s ST data transfer rates OS Support Windows 2012 and RedHat nterprise and SUS Linux. Power onsumption 15.1 Watts Physical imensions ard PB dimensions: 6.1" x 2.7 " (L x H) 1-1

8 O-S3216L-L16iT ontroller ard User's Guide Notes 1-2

9 hapter 2: Hardware omponents hapter 2 Hardware omponents 2-1 ontroller ard Layout and omponents Figure 2-1. O-S3216L-L16iT The O-S3216L-L16iT is a low-profile PIe x8 Gen 3 controller card with sixteen internal SS3 ports packed in four mini SS H connectors. The following pages describe the components and settings for the O-S3216L-L16iT. 2-1

10 B MH U21 MH2 MIO 1 J5 URT0 L8 L5 L7 8 7 G U20 N H2 8 H1 7 PRSS FIT N2 L2 19 J* B1 B11 B12 J1 B9 K Y R K U Y1 J2 N0 N1 N N5 P8 P7 P2 P1 L8 L7 8 7 O8 O7 O2 O1 K7 K1 8 7 M8 M7 N8 N7 J8 K8 B2 B1 M1 I7 7 M2 I8 8 B O-S3216L-L16iT ontroller ard User's Guide 2-2 Major omponents The following are the major components that make up the O-S3216L-L16iT controller card: G O-S3216L-L16iT RV: SS12-15 SS PRSS FIT L2 L1 H2 H N2 N1 J2 J1 K2 I2 I G G3 SS 0-3 SS -7 SS SS SIGN IN US Figure 2-2. O-S3216L-L16iT Layout O-S3216L-L16iT omponent escription 1 SS onnectors SS SS onnectors SS SS onnectors SS 8-11 SS onnectors SS MIO Header, designated MIO, 6 URT Header, designated URT0 Serial ebug Port, J5 2-2

11 93 LT13 RT13 B 1 TP3 T6 5 1 MH U21 MH2 MIO 1 J5 URT0 L8 G3 L5 L7 8 7 G U20 N H2 8 H1 7 PRSS FIT N2 L2 1 2 B1 B H1 H S56 S55 S57 S58 S60 S59 S62 S S6 S63 19 J* B1 B11 B12 J1 B LT15 RT15 K Y LT20 RT20 RT11 LT11 RT19 LT19 R K 9 U LT2 RT2 LT16 RT16 Y1 J2 N0 N1 N N5 P8 P7 P2 P1 L8 L7 8 7 RT8 O8 O7 O2 O1 K7 P8 P7 L8 L7 L2 L1 H2 H1 K1 1 P2 P M8 M7 N8 N7 J8 K8 2 B2 B1 O8 O7 O2 O1 K8 K7 K2 K M1 I7 7 N8 N7 N2 N1 J8 J2 J1 B2 B1 M2 I8 8 M7 M2 M1 I7 I2 I M8 I8 8 8 G5 RN1 RN2 G G3 B 1 Q1 RT3 RT12 LT3 90 RT1 LT1 2 1 RT17 81 RT18 LT17 RT1 LT1 RT S5 S6 S39 S0 S1 S2 S3 S S51 S52 S37 S38 S7 S8 89 T62 T8 R157 R S70 S69 S9 S50 S RN3 RN T77 T9 TP26 T S85 S86 S76 S75 S79 S80 S81 S82 S71 S73 T91 77 J6 U5 212 S8 S S77 S78 S7 hapter 2: Hardware omponents 2-3 onnectors and L SS onnectors There are four mini SS H connectors on the controller card, providing 16 ports that support a transfer rate on each port of up to 12 Gb/s with SS devices and 6Gb/s with ST devices. 11 G O-S3216L-L16iT RV: SS12-15 SS PRSS FIT L2 L1 H2 H N2 N1 J2 J1 K2 I2 I G G3 SS 0-3 SS -7 SS SS SIGN IN US Figure 2-3. SS3 onnectors O-S3216L-L16iT omponent escription 1 SS onnectors SS SS onnectors SS -7 3 SS onnectors SS 8-11 SS onnectors SS Heartbeat L Heartbeat L blinking green L indicates the firmware is running on the controller chip. BR O T3 LT T T151 T LT8 201 R257 T LT12 T R212 7 T TP1 T82 70 LT18 S T73 R5 T TP0 T72 T69 T56 T50 T76 T T37 68 T121 T35 T T105 T T113 T87 72 T T T61 T95 T112 T79 T S66 S67 S65 51 T83 T T93 T T136 T9 T86 T92 T135 T9 6 T90 T57 T6 R16 R T6 R71 R82 13 T1 T15 T88 T8 T10 T80 T85 T103 T89 T106 T30 T31 T81 T78 T65 T68 T71 T5 T38 T67 T59 T0 T60 T51 T2 T55 T115 T5 T70 T1 T28 T129 T75 T36 T33 T63 R20 T32 T122 T18 T126 T127 T128 T125 1 R53 T120 S3 S2 T1 S5 S T131 T132 T130 S7 S6 T101 T150 T19 S9 S8 T109 T100 T123 T66 T52 T53 T7 T T107 T108 T18 T15 S11 S10 T17 T12 T13 T10 S13 S12 T133 S15 S1 T11 T137 T138 T139 S17 S16 T25 37 T R162 R283 R61 R62 R63 R83 U1 R27 R65 R66 R28 R81 RS3 RS R R259 R117 R11 R115 T3 R92 R90 R95 R93 R96 R9 R91 R89 RS1 RS2 R131 R111 R2 R1 R126 R32 RS8 TP10 R28 R267 R265 U R268 R266 R263 R261 R26 R262 RN5 RN6 RS11 RS12 U13 R275 R27 R273 R116 R121 R113 RS10 U2 TP2 TP TP3 TP35 TP6 TP5 TP32 TP33 TP31 TP30 RS9 R128 R6 R5 R R276 TP25 TP22 TP21 TP27 TP28 TP29 T116 T102 R271 R269 TP11 TP13 TP50 TP8 TP7 TP9 TP16 TP20 TP15 TP19 R272 R270 TP12 TP1 TP18 TP17 TP23 TP2 G B F TP1 G B F HB_L 15 I0 2-3

12 B MH U21 MH2 MIO 1 J5 URT0 L8 L5 L7 8 7 G U20 N H2 8 H1 7 PRSS FIT N2 L2 19 J* B1 B11 B12 J1 B9 K Y R K U Y1 J2 N0 N1 N N5 P8 P7 P2 P1 L8 L7 8 7 O8 O7 O2 O1 K7 K1 8 7 M8 M7 N8 N7 J8 K8 B2 B1 M1 I7 7 M2 I8 8 B O-S3216L-L16iT ontroller ard User's Guide 2- Front Header Locations J O-S3216L-L16iT RV:1.00 SS12-15 SS PRSS FIT L2 L1 H2 H N2 N1 J2 J1 K2 G5 I2 I G G3 SS 0-3 SS -7 SS SS SIGN IN US Figure 2-. Headers for ngineering Tests O-S3216L-L16iT escription URT Header, designated URT0 Serial ebug Port J5 MIO Header, designated MIO Purpose For ngineering ebug For ngineering Test 2-

13 hapter 3: Installation hapter 3 Installation 3-1 Static-Sensitive evices lectrostatic ischarge (S) can damage electronic com ponents. To avoid damaging your controller card, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from S. Precautions Use a grounded wrist strap designed to prevent static discharge. Touch a grounded metal object before removing the controller card from the antistatic bag. Handle the expansion card by its edges only; do not touch its components or peripheral chips. Put the controller card back into the antistatic bags when not in use. For grounding purposes, make sure that your system chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the controller card. Unpacking The controller card is shipped in antistatic packaging to avoid static damage. When unpacking your component, make sure you are static protected. Note: To avoid damaging your components and to ensure proper installation, be sure to always connect the power cord last, and always remove it before adding, removing or changing any hardware components. 3-1

14 O-S3216L-L16iT ontroller ard User's Guide 3-2 Before Installation To install the controller card properly, follow the steps below. Prior to Installation 1. Power down the system and unplug the power cord. 2. Use industry-standard anti-static equipment (such as gloves or wrist strap) and follow the precautions on page 3-1 to avoid damage caused by S. 3-3 Installing the ontroller ard epending upon which system configuration is used, a riser card may or may not be required to install the O-S3216L-L16iT. Installing the ontroller ard 1. Power down the system, remove the power cords from the rear of the power supply and remove the system cover. 2. Verify that your controller card is equipped with the correct length of PIe slot mounting bracket for your system. The O-S3216L-L16iT controller card includes a low-profile PIe mounting bracket. However, if your system features full-height PIe slots, replace the low-profile bracket with a full-height bracket. 3. Insert the controller card into a x8 PI- slot.. onnect the mini SS H cables from the controller card to either the direct attached storage target devices or the cable sockets on the backplanes. 5. The cable latch will click into the locked position when connected properly. 6. Replace the system cover, plug in the power cord and power up the system. 3-2

15 B MH U21 MH2 MIO 1 J5 URT0 L8 L5 L7 8 7 G U20 N H2 8 H1 7 PRSS FIT N2 L2 19 J* B1 B11 B12 J1 B9 K Y R K U Y1 J2 N0 N1 N N5 P8 P7 P2 P1 L8 L7 8 7 O8 O7 O2 O1 K7 K1 8 7 M8 M7 N8 N7 J8 K8 B2 B1 M1 I7 7 M2 I8 8 B hapter 3: Installation G O-S3216L-L16iT RV:1.00 SS12-15 SS PRSS FIT L2 L1 H2 H N2 N1 J2 J1 K2 I2 I G G3 SS 0-3 SS -7 SS SS SIGN IN US Figure 3-1. onnecting the ables 3-3

16 O-S3216L-L16iT ontroller ard User's Guide 3- Static Sensitive evices lectrostatic ischarge (S) can damage electronic com ponents. To avoid damaging your controller card, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from S. Precautions Use a grounded wrist strap designed to prevent static discharge. Touch a grounded metal object before removing the controller card from the antistatic bag. Handle the controller card by its edges only; do not touch its components or peripheral chips. Put the controller card back into the antistatic bags when not in use. For grounding purposes, make sure that your system chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the controller card. Unpacking The controller card is shipped in antistatic packaging to avoid static damage. When unpacking your component, make sure you are static protected. Note: To avoid damaging your components and to ensure proper installation, be sure to always connect the power cord last, and always remove it before adding, removing or changing any hardware components 3-

17 hapter 3: Installation 3-5 Installing the rivers in Windows Refer to the instructions that came with your controller card and follow the manufacturer's recommended steps for installing the operating system driver. ownload the latest drivers from the Supermicro project board at ftp://ftp.supermicro.com/ driver/ss/lsi/ Uninstalling the rivers To Uninstall the rivers in Windows: Follow the system driver uninstall procedure in the operating system. 3-5

18 O-S3216L-L16iT ontroller ard User's Guide (isclaimer ontinued) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage. ccordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale. 3-6