IP413 ATX COM Express Type 6 Baseboard User s Manual

Transcription

1 IP43 ATX COM Express Type 6 Baseboard User s Manual Version.0 (July 07)

2 Copyright 07 IBASE Technology, Inc. All rights reserved. No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as IBASE ). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice. Every effort has been made to ensure the information in the document is correct; however, IBASE does not guarantee this document is error-free. IBASE assumes no liability for incidental or consequential damages arising from misapplication or inability to use the product or the information contained herein, nor for any infringements of rights of third parties, which may result from its use. Trademarks All the trademarks, registrations and brands mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners. ii IP43 User s Manual

3 Compliance In a domestic environment, this product may cause radio interference in which case users may be required to take adequate measures. This product has been tested and found to comply with the limits for a Class A device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer s instructions, may cause harmful interference to radio communications. WEEE This product must not be disposed of as normal household waste, in accordance with the EU directive of for waste electrical and electronic equipment (WEEE - 0/9/EU). Instead, it should be disposed of by returning it to a municipal recycling collection point. Check local regulations for disposal of electronic products. Green IBASE This product is compliant with the current RoHS restrictions and prohibits use of the following substances in concentrations exceeding 0.% by weight (000 ppm) except for cadmium, limited to 0.0% by weight (00 ppm). Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent chromium (Cr6+) Polybrominated biphenyls (PBB) Polybrominated diphenyl ether (PBDE) IP43 User s Manual iii

4 Important Safety Information Carefully read the precautions before using the board. Environmental conditions: Use this product in environments with ambient temperatures between 0 C and 60 C. Do not leave this product in an environment where the storage temperature may be below -0 C or above 80 C. To prevent from damages, the product must be used in a controlled environment. Care for your IBASE products: Before cleaning the PCB, unplug all cables and remove the battery. Clean the PCB with a circuit board cleaner or degreaser, or use cotton swabs and alcohol. Vacuum the dust with a computer vacuum cleaner to prevent the fan from being clogged. Attention during use: WARNING. Do not use this product near water. Do not spill water or any other liquids on this product. Do not place heavy objects on the top of this product. Anti-static precautions Wear an anti-static wrist strap to avoid electrostatic discharge. Place the PCB on an anti-static kit or mat. Hold the edges of PCB when handling. Touch the edges of non-metallic components of the product instead of the surface of the PCB. Ground yourself by touching a grounded conductor or a grounded bit of metal frequently to discharge any static. CAUTION Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer s instructions or recycle them at a local recycling facility or battery collection point. iv IP43 User s Manual

5 Warranty Policy IBASE standard products: 4-month (-year) warranty from the date of shipment. If the date of shipment cannot be ascertained, the product serial numbers can be used to determine the approximate shipping date. 3 rd -party parts: -month (-year) warranty from delivery for the 3 rd -party parts that are not manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices, power adapter, panel and touchscreen. * PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT, IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED FOR REPAIR AND SHIPPING CHARGES. Technical Support & Services. Visit the IBASE website at to find the latest information about the product.. If you need any further assistance from your distributor or sales representative, prepare the following information of your product and elaborate upon the problem. Product model name Product serial number Detailed description of the problem The error messages in text or in screenshots if there is any The arrangement of the peripherals Software in use (such as OS and application software, including the version numbers) 3. If repair service is required, you can download the RMA form at Fill out the form and contact your distributor or sales representative. IP43 User s Manual v

6 Table of Contents Compliance... iii Important Safety Information... iv Warranty Policy... v Technical Support & Services... v Chapter General Information.... Introduction.... Features....3 Specifications Overview Dimensions... 7 Chapter Hardware Configuration Setting the Jumpers How to Set Jumpers Connector Locations on IP Jumpers Quick Reference AT/ATX Power Selection (J9) LVDS Panel Power (JP0) LVDS Backlight Power Selection (JP8) COM RS-3/4/485 Selection (JP, JP3, JP4) PS/ KB/MS Power Selection (JP) COM & COM RS-3 Power Selection (JP6, JP5) Connectors Quick Reference SATA HDD Power Connector (J0) PS/ Keyboard and Mouse Connector (J6) COM & COM RS-3/4/485 Ports (CN3) Audio Connector for Chassis Front Panel (JP) BIOS Boot Selection (SW) COM3 & COM4 RS-3 Port (J, J) ATX Power Supply Connector (J) DC-In V Power Connector (J) Panel Inverter Power Connector (JP7) LVDS Connector (CN9, CN8)... 6 vi IP43 User s Manual

7 .4. USB.0 Ports (JP9) System Function Connector (J8) Parallel Port (LPT) Fan Power Connector (CPU_FAN, SYS_FAN) DVI Port (JP3) VGA Port (VGA)... 3 IP43 User s Manual vii

8 This page is intentionally left blank. viii IP43 User s Manual

9 Chapter General Information The information provided in this chapter includes: Features Specifications Board Overview Board Dimensions

10 . Introduction IP43 is a ATX COM Express Type 6 baseboard, offering expansion slots like ISA and PCI and rich peripheral ports as the photo shown below. It is able to be operated at the ambient operating temperature ranging from 0 ~ 60 C and even from -0 ~ 80 C for storage. Photo of IP43-ATX. Features x PCI-E(x6), x PCI-E(x4), 3x PCI-E(x) expansion slots Rich peripheral ports: USB 3.0, USB.0, LAN, DP, HDMI, audio jacks, serial COM port On-board headers for serial port (from COMe module), PS/ KB & MS, DVI-D, CRT, and ATX power connector, and COM Express (Type 6) connectors ATX power connector / DC-In V IP43 User s Manual

11 General Information.3 Specifications Product Name IP43 Form Factor ATX COM Express Type 6 baseboard Power Supply ATX Power Dimensions 305 x 44 mm ( x 9.6 ) RoHS Yes I/O Ports / Connectors Power Supply Display LAN USB Serial Audio Jacks ATX Power DC-In V x HDMI x DisplayPort x DVI-D x VGA x LVDS x RJ45 0/00 Mbps LAN 4 x USB.0 ( are on the I/O coastline, and are on-board box-headers.) 4 x USB 3.0 x COM ports: COM: RS-3/4/485 (I/O coastline connector) COM: RS-3 (full-function) (I/O coastline connector) COM3 & COM4: RS-3 (TX and RX) (from COMe module, via an on-board box-header) x Line-In x Line-Out x Microphone Input IP43 User s Manual 3

12 Keyboard & Mouse Battery for RTC/CMOS Expansion Slots Temperature Relative Humidity x PS/ keyboard / mouse on-board header x Lithium battery cell for RTC of COM Express module x PCIe (x6) slot x PCIe (x4) slot 3 x PCIe (x) slot x Full-sized mini-pcie (x) slot with PCIe only (half-sized mounting hole is reserved.) Environment Operation: 0 ~ 60 C Storage: -0 ~ 80 C 0 ~ 90 % All specifications are subject to change without prior notice. 4 IP43 User s Manual

13 General Information.4 Overview Top View IP43-ATX IP43-DC *The photos above are for reference only. Some minor components may differ. IP43 User s Manual 5

14 I/O View No. Name No. Name COM RS-3/4/485 Port 6 DisplayPort COM RS-3 Port 7 USB 3.0 Ports 3 GbE LAN Port 8 Audio Line-In 4 USB.0 Ports 9 Audio Line-Out 5 HDMI Port 0 Microphone Input 6 IP43 User s Manual

15 General Information.5 Dimensions IP43 User s Manual 7

16 Chapter Hardware Configuration This section provides information on jumper settings and connectors on the IP43 in order to set up a workable system. Jumper and connector locations Jumper settings and information of connectors 8

17 Hardware Configuration. Setting the Jumpers Set up and configure your IP43 by using jumpers for various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your use... How to Set Jumpers Jumpers are short-length conductors consisting of several metal pins with a non-conductive base mounted on the circuit board. Jumper caps are used to have the functions and features enabled or disabled. If a jumper has 3 pins, you can connect either PIN to PIN or PIN to PIN3 by shorting. Pin# 3 A 3-pin jumper A jumper cap Refer to the illustration below to set jumpers. Pin closed Oblique view Schematic illustration in the manual Open When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. IP43 User s Manual 9

18 . Connector Locations on IP43 CN6 CN4 CN5 CN CN CN7 CN3 PCIEX-3 PCIEX- J7 PCIEX- PCIEX4- JP 9 0 PCIEX6 JP0 J3 J0 9 CN J 0 J 0 0 JP9 CN8 CN CN3 9 CN0 CN RESC VGA 5 JP8 JP7 RESC JP3 JP JP4 JP6 JP5 CPU_FAN JP J5 JP J4 LPT J6 SW3 SW SW JP3 3 7 J8 7 J J J 3 Battery SYS_FAN Board diagram of IP43 0 IP43 User s Manual

19 Hardware Configuration.3 Jumpers Quick Reference Function Jumper Name Page AT/ATX Power Selection J9 LVDS Panel Power JP0 LVDS Backlight Power Selection JP8 3 COM RS-3/4/485 Selection JP, JP3, JP4 4 PS/ Keyboard & Mouse Power Selection JP 5 COM & COM RS-3 Power Selection JP6 (for COM), JP5 (for COM) 6.3. AT/ATX Power Selection (J9) Function Pin closed Illustration ATX (default) Open AT Close IP43 User s Manual

20 .3. LVDS Panel Power (JP0) Function Pin closed Illustration 3.3V (default) - 5V -3 IP43 User s Manual

21 Hardware Configuration.3.3 LVDS Backlight Power Selection (JP8) Function Pin closed Illustration 3.3V (default) Open 5V Close IP43 User s Manual 3

22 .3.4 COM RS-3/4/485 Selection (JP, JP3, JP4) JP JP3 JP4 6 5 Function Pin closed Illustration JP: 3-5 & RS-3 (default) JP3: 3-5 & JP4: JP: -3 & RS-4 JP3: -3 & JP4: IP43 User s Manual

23 Hardware Configuration Function Pin closed Illustration JP: -3 & RS-485 JP3: -3 & JP4: PS/ KB/MS Power Selection (JP) Function Pin closed Illustration 5VSB (default) - 5V -3 IP43 User s Manual 5

24 .3.6 COM & COM RS-3 Power Selection (JP6, JP5) JP6 (for COM) JP5 (for COM) 5 6 Function Pin closed Illustration V Normal (default) V IP43 User s Manual

25 Hardware Configuration.4 Connectors Quick Reference Function Connector Name Page SATA HDD Power Connector J0 8 PS/ Keyboard and Mouse Connector J6 9 COM & COM RS-3 Ports CN3 0 Audio Connector for Chassis Front Panel JP BIOS Boot Selection SW COM3 & COM4 RS-3 Port J (COM3), J (COM4) 3 ATX Power Supply Connector J 4 DC-In V Power Connector J 5 Panel Inverter Power Connector JP7 5 LVDS Connector CN9 (Channel), CN8 (Channel) USB.0 Ports JP9 7 System Function Connector J8 8 Parallel Port LPT 9 Fan Power Conenctor CPU_FAN, SYS_FAN 30 DVI Port JP3 3 VGA Port VGA 3 HDMI Port CN -- DisplayPort CN -- USB 3.0 Ports CN4, CN5 -- GbE LAN Port CN7 -- Audio Jacks CN6 -- COM Express Connector RECS, RECS -- SATA III Port CN0, CN, CN, CN3 -- PCIe (x) Slot PCIEX-, PCIEX-, PCIEX IP43 User s Manual 7

26 Function Connector Name Page PCIe (x4) Slot PCIE4- -- PCIe (x6) Slot PCIEX6- -- Mini-PCIe Slot J SATA HDD Power Connector (J0) Pin Assigment Pin Assigment +5V 3 Ground Ground 4 +V 8 IP43 User s Manual

27 Hardware Configuration.4. PS/ Keyboard and Mouse Connector (J6) 7 8 Pin Assigment Pin Assigment 5V 5V 3 Mouse data 4 Keyboard data 5 Mouse clock 6 Keyboard clock 7 Ground 8 Ground IP43 User s Manual 9

28 .4.3 COM & COM RS-3/4/485 Ports (CN3) COM: COM: Pin Assigment Pin Assigment DCD, Data carrier detect 6 DSR, Data set ready RXD, Receive data 7 RTS, Request to send 3 TXD, Transmit data 8 CTS, Clear to send 4 DTR, Data terminal ready 9 RI, Ring indicator 5 Ground 0 IP43 User s Manual

29 Hardware Configuration.4.4 Audio Connector for Chassis Front Panel (JP) 9 0 Pin Assigment Pin Assigment MIC IN_L Ground 3 MIC IN_R 4 Detection 5 LINE_R 6 Ground 7 Sense 8 NC 9 LINE_L 0 Ground JP is utilized for the following front panel functions for your system. Microphone Input (Pins and 3) The two pins are connected to the microphone input connector of your system. Line Input (Pins 5 and 9) The two pins are connected to the Line-In connector of your system. IP43 User s Manual

30 .4.5 BIOS Boot Selection (SW) SPICS0# SPICS# SPI0/FWH Pin Pin Module (default) Module SPI0 OFF OFF Module Module Carrier FWH ON OFF Carrier Module SPI0/SPI OFF ON Module Carrier SPI0/SPI ON ON IP43 User s Manual

31 Hardware Configuration.4.6 COM3 & COM4 RS-3 Port (J, J) J (COM3) J (COM4) Pin Assigment Pin Assigment NC 6 NC RXD, Receive data 7 NC 3 TXD, Transmit data 8 NC 4 NC 9 NC 5 NC IP43 User s Manual 3

32 .4.7 ATX Power Supply Connector (J) 3 4 Pin Assigment Pin Assigment 3.3V 3 3.3V 3.3V 4 -V 3 Ground 5 Ground 4 +5V 6 PS-ON 5 Ground 7 Ground 6 +5V 8 Ground 7 Ground 9 Ground 8 Power good 0-5V 9 5VSB +5V 0 +V +5V +V 3 +5V +3.3V 4 Ground 4 IP43 User s Manual

33 Hardware Configuration.4.8 DC-In V Power Connector (J) 3 4 Pin Assigment Pin Assigment Ground 3 +V Ground 4 +V.4.9 Panel Inverter Power Connector (JP7) Pin Assigment Pin Assigment +V 3 ADJ Backlight Enable 4 Ground IP43 User s Manual 5

34 .4.0 LVDS Connector (CN9, CN8) CN9 (Channel) CN8 (Channel) 0 9 Pin Assigment Pin Assigment TX0P TX0N 3 Ground 4 Ground 5 TXP 6 TXN 7 Ground 8 Ground 9 TXP 0 TXN Ground Ground 3 CLKP 4 CLKN 5 Ground 6 Ground 7 TX3P 8 TX3N 9 Power 0 Power 6 IP43 User s Manual

35 Hardware Configuration.4. USB.0 Ports (JP9) 0 9 Pin Assigment Pin Assigment VCC VCC 3 D0-4 D- 5 D0+ 6 D+ 7 Ground 8 Ground 9 NC 0 NC IP43 User s Manual 7

36 .4. System Function Connector (J8) 8 7 Pin Assigment Pin Assigment Power BTN Power BTN 3 HDD LED+ 4 HDD LED- 5 Reset BTN 6 Reset BTN 7 Power LED+ 8 Power LED- 8 IP43 User s Manual

37 Hardware Configuration.4.3 Parallel Port (LPT) Pin Assigment Pin Assigment Line printer strobe 4 AutoFeed PD0, parallel data 0 5 Error 3 PD, parallel data 6 Initialize 4 PD, parallel data 7 Select 5 PD3, parallel data 3 8 Ground 6 PD4, parallel data 4 9 Ground 7 PD5, parallel data 5 0 Ground 8 PD6, parallel data 6 Ground 9 PD7, parallel data 7 Ground 0 ACK, acknowledge 3 Ground Busy 4 Ground Paper empty 5 Ground 3 Select 6 N/A IP43 User s Manual 9

38 .4.4 Fan Power Connector (CPU_FAN, SYS_FAN) CPU_FAN: SYS_FAN: Pin Assigment Pin Assigment Ground 3 NC +V 30 IP43 User s Manual

39 Hardware Configuration.4.5 DVI Port (JP3) 9 0 Pin Assigment Pin Assigment TXP TXIN 3 GND 4 GND 5 TXCP 6 TXCN 7 GND 8 +5V 9 HTPG 0 NC TXP TXN 3 GND 4 GND 5 TX0P 6 TX0N 7 NC 8 NC 9 DDCDATA 0 DDCCLK IP43 User s Manual 3

40 .4.6 VGA Port (VGA) 6 5 Pin Assigment Pin Assigment CRT_R +5V 3 CRT_G 4 GND 5 CRT_B 6 NC 7 NC 8 DDC_DATA 9 GND 0 CRT_HSYN GND CRT_VSYN 3 GND 4 DDC_CLK 5 GND 6 NC 3 IP43 User s Manual