Installation Instructions. P/N Revision A April Single Dock. P/N Revision A

Transcription

1 nstallation nstructions P/N Revision A April Single Dock P/N Revision A

2 tem# Description PN Qty 1. Power supply ref.*. cable, dock to PC-AT or x ref.* laptop. cable, dock to PC-XT or x ref.* PS 4. cable, dock to modem x ref.* 5. cable, dock to printer (NORAND printers only) ref.* 6. cable, dock to serial x ref. printers 7. kit, mounting plate and ref.* four screws 8. bracket, wall mount ref.*

3 ntroduction

4 Mounting Bracket (plate) nstallation Kit Wall Mounting Kit Connections Connect all communication cables, as required. Connect the power supply cable to the single dock. Plug the ac cord into the power supply and then into a wall outlet. 4

5 NSTRUCTONS: 1. Position the wall mount bracket (1) on the wall at a convenient height. Make sure the bracket is level and that the keyholes () are positioned as shown.. Use a pencil to mark the location of the four bracketmounting holes () when installing drywall mollies or other anchor devices (1/4-inch minimum diameter). Select and install wall anchor devices according to the manufacturer s instructions. Use four 1/4-inch diameter lag screws when installing the bracket on a board or other reinforced wall surface.. Remove the screw from the bottom of the dock, then align and lower the dock in the keyhole cutouts () nsert the screw removed in Step # through this hole (4) and into the dock to secure it in place. 4 Figure nstall Wall Mount Bracket 5

6 NSTRUCTONS 1. Positionner le support (1) pour installation murale à une hauteur convenable sur le mur. Bien vérifier que le support est horizontal et que les trous piriformes () sont placés selon l illustration.. Pour la pose de boulons à coquille d expansion de type Molly ou d autres pièces de fixation (d un diamètre minimum de 1/4 po), marquer au crayon l emplacement des quatre trous de fixation () du support. Voir le mode d emploi du fabricant pour le choix et la pose des dispositifs de fixation murale. Pour la pose du support sur un panneau ou une surface murale renforcée, utiliser quatre tire fond de 1/4 po de diamètre.. Retirer la vis de la partie inférieure de la station multi accueil, puis aligner la station sur les trous piriformes () et l abaisser. 4. nsérer la vis retirée à l étape dans le trou (4) et dans la station multi accueil pour bien fixer la station en place. 1 4 Figure Pose du support pour installation murale 6

7 NSTRUCTONS: Once the dock is secure in the keyhole cutouts, be sure to install a screw up through the hole in the bottom of the bracket and into the Single Dock pin COMMUNCATON connector (RS/RS485 ). -pin POWER Connector. Wall mounting bracket Figure Wall Mount and Basic Single Dock (connectors on side) 7

8 DC Power Connector 1 A COM B COM pin POWER Connector. 5-pin DN Connector (for external keyboard).. 5-pin COMMUNCATON connectors (RS/RS485 ) 4. 8-pin RJ-45 LAN (Ethernet) Jack Figure 4 Full-Function Single Dock Connectors (connectors on rear) 8

9 PN 1 PN 1 PN 5 PN 14 COM Port A Pin Purpose 1 Chassis ground TXD RXD 4 RTS 5 CTS 6 DSR 7 Ground 8 DCD 9 RS RS Not Used 0 DTR 1 Not Used R 5 Not used COM Port B Pin Purpose 1 Chassis ground TXD RXD 4 RTS 5 CTS 6 DSR 7 Ground 8 DCD 9 RS RS Not Used 18 Dock control line for port B 19 Not Used 0 DTR 1 Not Used R 5 Not used 9

10 Surface Connectors 1 1 Contact # Signal Name n/out Use RS485+ KCLK RS485 KDAT TPN EXT_KB_L TPP R CHRG_EXT DCD CHRG_EXT DSR TPON CTS TPOP RXD DOCK CNTRL TXD GND RTS GND DTR /O /O /O O O O O O O 485 LAN + External Keyboard 485 LAN External Keyboard Data External nput Reset Sense for External Keyboard Ethernet nput Positive RS Ring ndicator External Charge Voltage RS Data Carrier Detect External Charge Voltage RS Data Set Ready Ethernet Output Negative RS Clear To Send Ethernet Output Positive RS Receive Data Dock Control Line RS Transmit Data GROUND RS Request To Send GROUND RS Data Terminal Ready 10

11 1 1. AC power cord. Power Supply. -pin power connector Figure 5 Power Supply Assembly (PN: ) 11

12