Rayson Bluetooth Module

Transcription

1 Rayson Bluetooth Module Low Energy Smart Module Features Bluetooth standard V4.0 conformity. CSR000/00 chip Programmable general purpose PIO controller : Switch-mode power supply. IC for EEPROM and ICs peripherals. -9.5dBm Bluetooth low energy RX sensitivity. digital PIOs analogue AIOs 4 PWM modules Watchdog timer Option for built-in G-sensor RoHS Compliant Small outline. 0(6) x x.0mm (option wo/antenna) Applications Sports and fitness Healthcare Automotive Home entertainment Office and mobile accessories Commercial Outline BTM-800 Electrical Characteristics Absolute Maximum Ratings Ratings Min. Max. Storage Temperature Supply Voltage :.8V.6 V Recommended Operating Condition Operating Condition Min. Max. Operating Temperature range Supply voltage:.8v.6v

2 Current Consumption(CSR00 QFN total typical current consumption measured at the battery) MODE Descrisption Total Typical Current at Dormant functions are shutdown. To wake up toggle the WAKE pin <600nA Deep sleep VDD_PADS = ON, REFCLK = OFF, SLEEPCLK = ON, VDD_BAT = ON, RAM = ON, digital circuits = ON, <5μA SMPS = ON (low-power mode), ms wake-up time Idle VDD_PADS = ON, REFCLK = ON, SLEEPCLK = ON, ~ma VDD_BAT = ON, RAM = ON, digital circuits = ON, MCU = IDLE, <μs wake-up time RX / TX active - peak current Block Diagram Radio Characteristics

3 Note: (a) Up to five exceptions are allowed in the Bluetooth V4.0+EDR specification on receiver part.. (b) Measured at F 0 = 44MHz. (c) Measured at f-f=5mhz. Measurement is performed in accordance with Bluetooth RF test RCV/CV/05.., i.e., wanted signal at -64dBm (d) Measured at unbalanced port of balun. Integrated in 00KHz bandwidth and normalised to Hz. actual figure is typically below -0dBm/Hz except for peaks -80dBm at 600MHz, -80dBm in band at.4ghz and -80dBm at.ghz Note: () Measurements methods are in accordance with the Bluetooth V4.0+EDR specification. () Up to five exceptions are allowed in the Bluetooth V4.0+EDR specification on receiver part. () Measured at F0 = 405MHz, 44MHz, 477MHz.

4 Application circuit UART_TX UART_RX C 00n C 00n R6 NC R7 VCC 5 U C+ V+ 7 4 V- 5 C- 0 C+ Inv alid ForceOn 6 6 ForceOf f C- DIN DOUT EN 9 ROUT RIN 8 MAX GND 4 C5 00n C4 00n RXD TXD J DB9 MALE DB9 PINOUT. DCD. RX DATA. TX DATA 4. DTR 5. GND 6. DSR 7. RTS 8. CTS 9. RING R5 PIO- PIO-0 PIO-4 PIO- UART_RX UART_TX AIO-0 AIO- AIO- IC-SDA IC-SCL SW GREEN R 8 LED GREEN R 8 LED R4 P LS SPEAKER U GND 4 RF_IN GND SPI_PIO#_SEL UART_RX 0 UART_TX 9 8 AIO[0] 7 AIO[] 6 AIO[] IC_SDA 5 4 IC_SCL WAKE PIO[] PIO[4] SPI_CLK SPI_CSB SPI_MOSI SPI_MISO PIO[9] PIO[0] PIO[] GND PIO[] BTM-800 P PIO- PIO-4 SPI-CLK SPI-CSB SPI-MOSI SPI-MISO PIO-9 PIO-0 PIO- PIO- BAT SW R C 00u TP TP TP TP4 TP5 TP6 TP7 TP8 UART_RX UART_TX SPI-MOSI SPI-CLK SPI-CSB SPI-MISO

5 BTM-800 Pins Function No. Pin Name Pin Type Pin description PIO[] Bi-directional Programmable input/output line or PWN signal output PIO[4] Bi-directiona Programmable input/output SPI_CLK( PIO5) Bi-directiona Programmable input/output or debug SPI_CLK selected 4 SPI_CSB( PIO6) Bi-directional Programmable input/output or debug SPI chip selected 5 SPI_MOSI( PIO7) Bi-directional Programmable input/output or debug SPI_MOSI selected 6 SPI_MISO(PIO8) Bi-directiona Programmable input/output or debug SPI_MISO selected 7 PIO[9] Bi-directiona Programmable input/output line 8 PIO[0] Bi-directiona Programmable input/output line 9 PIO[] Bi-directional Programmable input/output line or button input 0 Power input Connect to external (battery) and regulator enable GND GND output Common ground PIO Bi-directional Provide IC Power can be used for power saving indication WAKE Bi-directional Input to wake module from domand/hibernate mode. if no use, pls pull down. 4 IC-SCL Bi-directiona IC clock or SPI serial flash clock output(sf_clk) 5 IC-SDA Bi-directiona IC data input/output or SPI serial flash data output(sf_dout) 6 AIO() Bi- Analogue Analogue Programmable input/output line 7 AIO() Bi- Analogue Analogue Programmable input/output line 8 AIO(0) Bi- Analogue Analogue Programmable input/output line 9 UART TX Bi-directiona Programmable input/output or UART TX 0 UART RX Bi-directional Programmable input/output or UART RX SPI_PIO#_SEL Bi-directional Programmable input/output or SPI/PIO selected,set HI for SPI GND GND Common ground RF_IN Analogue Antenna interface Request 4 GND GND Common ground

6 Dimension: Unit: mm

7 Document History Revision Date Change Reason Rev0 0/0/ Draft release Rev0 0/0/0 Added CSR00