Actual4Test. Actual4test - actual test exam dumps-pass for IT exams

Transcription

1 Actual4Test Actual4test - actual test exam dumps-pass for IT exams

2 Exam : C Title : IBM Certified System Programmer - IBM IMS Vendor : IBM Version : DEMO Get Latest & Valid C Exam's Question and Answers 1 from Actual4test.com. 1

3 NO.1 Your administrative scheduler shows message DSNA679I indicating that one or both copies of your task lists is not accessible or is corrupted. Your analysis shows that only the VSAM file is corrupt, but the ADMIN_TASKS table is still operational. Which statement describes how to correct this situation? A. Create an empty version of the VSAM task list and let DB2 perform an autonomic recovery using the content of the ADMIN_TASKS table. B. Create an empty version of the VSAM task list and use REPRO utility to copy the contents of the VSAM cluster containing the ADMIN_TASKS table. C. Create an empty version of the VSAM task list and use DB2 command -RECOVER TASKLIST to recover the content of the ADMIN_TASKS table. D. No manual interaction is needed as long as the ADMIN_TASKS table is still accessible. NO.2 Using the sample IBM supplied authorization exit, which authorization ID setting will be ensured? A. The initial primary authorization ID is unchanged as the DB2 primary ID, and the SQL ID is made equal to the DB2 primary ID, and one secondary ID exists and is the name passed by CICS or IMS. B. The initial primary authorization ID is set to the same value as the first secondary ID. C. The initial primary authorization ID remains the primary ID, the SQL ID is set equal to the primary ID, and the list of DB2 secondary IDs is set to the list of group names to which the RACF user ID is connected. D. The initial primary authorization ID remains the primary ID, the SQL ID is set equal to the RACF ID of the DB2 subsystem. NO.3 Dynamic Resource Definition can be used to replace which type of sysgen? A. ONLINE B. CTLBLKS C. NUCLEUS D. MODBLKS Answer: D NO.4 Which single DB2 system parameter must be enabled to allow system level backups to be used for object level recovery? A. RESTORE_SYSTEM B. RESTORE_ RECOVER_FROMDUMP C. SYSTEM_LEVEL_BACKUPS D. RESTORE_BACKUP NO.5 DB2 commands in data sharing can have a scope of group or a scope of member. Which three commands have a scope of member? (Choose three.) Get Latest & Valid C Exam's Question and Answers 2 from Actual4test.com. 2

4 A. -ACCESS DATABASE(DB1) SPACENAM(TS1) MODE(OPEN) B. -ARCHIVE LOG MODE(QUIESCE) C. -SET LOG SUSPEND D. -START DATABASE(DB1) SPACENAM(TS1) E. -STOP PROCEDURE(PROD.SP1),C,E NO.6 A DB2 subsystem is set up to take a checkpoint every two minutes. Applications that use this DB2 subsystem are supposed to adhere to an IT standard where a commit should be issued by the application at least every 200 SQL changes (INSERTs, UPDATES, or DELETEs). Which system parameter would be used to help implement the IT standard? A. URLGWTH B. CHKFREQ C. MAXDBAT D. LRDRTHLD NO.7 One of your Units of Recovery (URs) needs to be backed out. The back out fails due to a read I/O error on both copies of the archive log which is needed for the b ck out. DB2 issues a critical log read error indicating that a "must complete" operation could not be completed. Which statement is true? A. The error generates a write to operator with reply on the console asking you if DB2 should shut down. Other URs are not directly impacted and can continue to run. B. The error does not generate any write to operator with reply and DB2 abends automatically. C. The error generates a write to operator with reply on the console asking you if DB2 should shut down. All other URs are put on hold until you answer the write to operator reply. D. The error generates a write to operator with reply on the console asking you if you would like to CANCEL this UR with NOBACKOUT option and leave it in REFP restrictive state. NO.8 DSNZPARM parameter URLGWTH (UR LOG WRITE CHECK) is set to a very high value. Based on the warning messages caused by this setting, it is determined that a local thread that normally runs in a very short period of time has been completing changes for an excessively long period of time without a commit. The thread needs to be removed from the system with minimal log access. Which action should be taken to resolve the issue? A. Determine the token and issue the CANCEL DDF THREAD (token) NOBACKOUT. B. Determine the LUWID and issue the CANCEL DDF THREAD (luwid) DUMP. C. Determine the token and issue the CANCEL THREAD (token) NOBACKOUT. D. Determine the token and issue the CANCEL THREAD (token) DUMP. NO.9 In a non data sharing system, prefetch is getting disabled due to available buffers. Which buffer pool threshold parameter would you increase to reduce prefetch becoming disabled? Get Latest & Valid C Exam's Question and Answers 3 from Actual4test.com. 3

5 A. DWQT B. VDWQT C. VPSEQT D. VPXPSEQT NO.10 DB2 has written the following message to the system log: DSNP007I DSN3 DSNPXTN0 EXTEND FAILED FOR 229 DSNP.DSNDBD.DSNDB07.DSN4K03.I0001.A001. RC=00D70027 CONNECTION-ID=SERVER, CORRELATION-ID=java.exe, LUW ID=A49CA1E4.C F6A48E28B= Which action would you take to correct the problem? A. Alter the primary and/or secondary space quantity of the DSNDB07.DSN4K03 table space, and then execute the REORG utility. B. Use SQL to create an additional 4K table space in DSNDB07. C. Use SQL to create a new 32K table space in DSBDB07. D. Alter the primary and/or secondary space quantity of the DSNDB07.DSN4K03 table space, and then execute the RECOVER utility. Answer: B NO.11 All members of a data sharing group can be accessed by the group attachment name GRP. Two members (DB2A and DB2B) of the data sharing group are up on the same z/os and you run a batch job on this z/os with the following DSN command: DSN SYSTEM(GRP). Which statement is true? A. Your batch job will always be connected to DB2A. B. Your batch job will always be connected to DB2B. C. Your batch job will randomly be connected to either DB2A or DB2B. D. The connection is dependent on the definition in SYS1.PARMLIB member IEFSSNxx. NO.12 In IMS Connect, what commit-mode and sync-level does Resume Tpipe require? A. Commit Mode One (CM1), Sync level None (SL0) B. Commit Mode Zero (CM0), Sync level None (SL0) C. Commit Mode One (CM1), Sync level Confirm (SL1) D. Commit Mode Zero (CM0), Sync level Confirm (SL1) Answer: D Get Latest & Valid C Exam's Question and Answers 4 from Actual4test.com. 4