Nortel. Carrier VoIP Border Control Point Configuration and Datafill

Transcription

1 Nortel Carrier VoIP Border Control Point Configuration and Datafill Download Full Version :

2 D. Eight Answer: B QUESTION: 36 Assume that you are the administrator and must build a 7+1 fault tolerant cluster. How many RTP Portal members (Border Control Point (BCP) 7200) must be associated to the cluster name? A. Five B. Six C. Seven D. Eight Answer: D QUESTION: 37 Since the "service ID" for a 1+0 standalone cluster and a 1+1 fault tolerant cluster is configured as zero (0), which form is used to distinguish between the two cluster types? 29

3 A. Network Elements > Media Portals > RTP Portals > (RTP portal name) > NE Maintenance B. Network Elements > Media Portals > Media Portal Cluster > (cluster name) > Fault Tolerance C. Network Elements > Media Portals > Media Portal Cluster > (cluster name) > Configuration Parameters D. Network Elements > Media Portals > RTP Portals > (RTP portal name) > Configuration Parameters Answer: B QUESTION: 38 Assume that you are the administrator and must build a 2+1 fault tolerant cluster. You have already configured the two service IDs in the Media Portal Cluster folder. You have added the three BCP 7200s in the RTP Portals folder. Your next step is to go to the NE Maintenance form of the second BCP. What happens when the "Start" button on the second service instance is initiated? 30

4 A. This is the second BCP Service Instance in the Cluster and it is determined to be an active instance and advertises its availability to provide service to all call controllers. B. Once all members are started, the N+1 fault tolerant framework sets all members as active instances and advertises the cluster's availability to provide service to all call controllers. C. Once the OfficeTransferPeriod timer expires, the BCP service instance is set to active by the N+1 Fault-Tolerant Framework software which then advertises its availability to provide service to all call controllers. D. This is the second BCP Service Instance in the Cluster and it is determined to be the standby instance and advertises its availability to provide standby service to all call controllers in case an active instance fails. Answer: A QUESTION: 39 Assume that you are the administrator and must build a 1+1 fault tolerant cluster. You have already configured the service ID in the Media Portal Cluster folder. You have added the BCP 7200s in the RTP Portals folder. Your next step is to go to the NE Maintenance form of the second BCP What happens when the "Start" button on the second service instance is initiated? 31

5 A. The N+1 Fault-Tolerant Framework establishes the Cluster in run-time. Since this is the second Border Control Point (BCP) Service Instance in the Cluster, it is determined to be an active instance and advertises its availability to provide service to all call controllers. B. The N+1 Fault-Tolerant Framework establishes that this is a member of the Cluster. Once all members are started, the software sets this, as well as all members as active instances and advertises the cluster's availability to provide service to all call controllers. C. The N+1 Fault-Tolerant Framework establishes the Cluster in run-time. Since this is the second BCP Service Instance in the Cluster, the N+1 Fault-Tolerant Framework determines this to be the standby instance. This instance is set to operate in standby mode which monitors the status of the active member. D. The N+1 Fault-Tolerant Framework establishes the Cluster in run-time. Since this is the second BCP Service Instance in the Cluster it is determined to be the standby instance and advertises its availability to provide standby service to all call controllers in case an active instance fails. Answer: C QUESTION: 40 Under which situation would an IP address to added to the Network Data and Mtc > Addresses form? 32

6 A. It would be added whenever an IP address is to be referenced by another form or folder in the SMGUI. B. In the System Management Graphic User Interface (SMGUI), the Network Data and Mtc > Addresses form is pre-set and can never be added to or modified. C. It would be added only if the administrator prefers to use this centralized method of setting up IP addresses. Otherwise the IP addresses may be inserted manually on each form or folder in the SMGUI. D. Since the SMGUI comes pre-defined with default IP addresses, the Network Data and Mtc > Addresses is used for added new IP addresses and subnet masks unique for each system's needs. Answer: A 33

7 For More exams visit Kill your exam at First Attempt...Guaranteed!