NOVOtechnik. Content. TIM CANopen Gebrauchsanleitung TIM CANopen user manual SIEDLE GRUPPE

Transcription

1 Content 9 CANopen EDS Files Features Basic information Basics based on CiA DS-301, V Basics based on CiA DSP-406, V Basics SDO communication Basics PDO communication Object Library Communication Profile Area based on DS-301 V Device Profile Area Explanations to Object Library Object 0x1002 Manufacture Status Register LSS / Layer Setting Service Configuration of Node-ID Configuration of Bit Rate Activate Bit timing parameter Store Configuration Data SDO Services SDO Download SDO Upload SDO Abort Process Data PDO PDO Setting PDO message format Error Handling Emergency Messages Error Control Service Non-Volatile Storage and Data Restoration Abbreviations Document Changes 12 Version /10 Änderungen vorbehalten / Specifications subject to change 1

2 9 CANopen This document reflects the Novotechnik sensor protocol implementation of the standard CANopen protocol. A basic knowledge of the CAN Bus is required for a proper understanding of this document. Most of the definitions made are according to the following CiA Standard specifications. For making use of all the features that these specifications offer, a knowledge about them is absolutely necessary. The sensor supports the CANopen Communication profile DS-301, V4.02, Encoder profile DSP-406, V3.2 and Layer Setting Services (LSS) DSP-305, V EDS Files For integration in a common CANopen projecting tool, electronic data sheet (*.eds) files are provided. These files can be downloaded from the Novotechnik Web Site, see Downloads/Operating manuals where also this document can be found. Electric data sheet see file TIM_CANopen_Vx.x.eds 9.2 Features Basic information Vendor ID: 386 = 0x0182 (Novotechnik) Product code: = 0x0FBC Rev.-No.: 0x312E3031 Serial No.: see product label, xxxxxxxx z.b Basics based on CiA DS-301, V4.02 CAN Identifier CAN Bit rates Node-ID SYNC Time Stamp Emergency Messages Node Guarding Heartbeat Non-volatile storage Program Download NMT Service Standard 11 bit according to pre-defined connection set: Services NMT SYNC EMCY PDO1 () SDO (Rx) SDO () COB-ID 0x00 0x080 0x080 + Node-ID 0x180 + Node-ID 0x600 + Node-ID 0x580 + Node-ID Bit rate is defined in the ordering code: 6_9: 6_8: 6_7: 10 kbaud 20 kbaud 50 kbaud 6_5: 125 kbaud 6_4: 250 kbaud 6_3: 500 kbaud 6_2: 800 kbaud 6_1: 1000 kbaud setting per LSS (see chapter 9.5 LSS / Layer Setting Service) 0x7F setting per LSS (see chapter 9.5 LSS / Layer Setting Service) or object 0x100B (see chapter SDO Services) Consumer no Producer No Producer yes no Slave Version /10 Änderungen vorbehalten / Specifications subject to change 2

3 9.2.3 Basics based on CiA DSP-406, V3.2 Encoder class C1 C2 Encoder type Absolute Linear Encoder Basics SDO communication SDO communication expedited transfer segmented transfer Block transfer 1 Server yes no no Basics PDO communication PDO communication principle Producer TPDO: asynchronous with Event Timer, TPDO synchronous, Remote Transmission Request RTR PDO Mapping constant max. PDO Mapping logs per PDO 2 Version /10 Änderungen vorbehalten / Specifications subject to change 3

4 9.3 Object Library Communication Profile Area based on DS-301 V4.02 Object description Entry description Index/ Name Data Type Access PDO Default value Comment subindex Mapping 1000 device type unsigned32 ro no 0x000A0196 Device profile 406 multi-sensor encoder interface 1001 error register unsigned8 ro no 0x00 See chapter 9.8 Error Handling: 0x00: No error 0x81: transducer error 1002 manufacturer status register unsigned8 ro no 1 Additional manufacturer spec. status register (see chapter Object 1002) 1005 COB-ID SYNC unsigned32 rw no 0x COB-ID SYNC message (CANidentifier) 1008 manufacturer device name visible_ string const no f.e. TIM Device name, see datasheet/ordering code 1009 Hardware visible_string const no 1.00 Manufacturer Hardware Version 100A Software visible_string const no 1.00 Manufacturer Software Version 100B Node-ID unsigned32 ro no 127 Node-ID (can be changed via LSS s. chapter Configuration of Node- ID ) 100E COB ID Error unsigned32 rw no 0x COB ID Error Control Control + Node-ID 1010 store parameter unsigned8 ro no 1 This entry supports saving of parameters field in non volatile memory. With a read access the device provides information about its saving capabilities. For saving the signature "save" (0x ) must be written. 1010/1 store parameter unsigned32 rw no 0x Save all parameters 1011 restore default parameters unsigned8 ro no 1 This entry supports restoring of default parameters. With a read access the device provides information about its capabilities to restore these values. For restoring the signature "load" (0x64616f6c) must be written. 1011/1 unsigned32 rw no 0x6C6F6164 Restore all default parameters 1014 COB-ID EMCY unsigned32 rw no 0x Node-ID COB-ID used for emergency message (Emergency Server) producer heartbeat time unsigned16 rw no 0x disabled Heartbeat time periode in.ms. Range identify object unsigned8 ro no 4 General information about the device. This information is also used as the LSS address when using switch mode selective command 1018/1 unsigned32 ro no 0x Vendor ID 1018/2 unsigned32 ro no 0x0FBC Product code 1018/3 unsigned32 ro no 0x312E3031 Revision number 1018/4 unsigned32 ro no xxxxxxxx Serial number (see chapter Basic information) 1200 Server SDO unsigned8 ro no 2 Number of largest sub-index parameter /1 unsigned32 ro no 0x COB-ID client to server (Rx) + Node-ID 1200/2 unsigned32 ro no 0x Node-ID COB-ID server to client () Version /10 Änderungen vorbehalten / Specifications subject to change 4

5 Index/ subindex Object description Entry description Name Data Type Access PDO Mapping 1800 transmit PDO communication parameter 1 Default value Comment unsigned8 ro no 5 It contains the communication parameters of the current PDO the device is able to transmit. 1800/1 unsigned32 rw no 0x Node-ID COB-ID used by PDO1, transmission type of PD /2 unsigned8 rw no 0xFE = 254 Transmission type see chapter PDO Setting 1800/5 unsigned16 rw no 1 Event timer in ms Range A00 TPDO mapping parameter 1 Contains the mapping for the PDOs the device is able to transmit 1A00/0 unsigned8 const no 0x2 Number of entries 1A00/1 unsigned32 const no 0x Mapping entry 1: position value 1A00/2 unsigned32 const no 0x Mapping entry 2: speed value Device Profile Area Index/ subindex Object description Entry description Name Data Type Access PDO Mapping 6000 operating parameter 6005 Linear encoder measuring step settings Default value Comment unsigned16 rw no 0x0 This object contains the functions for code sequence and commissioning diagnostic control Object sets the number of distinguishable steps over the total measuring range (total resolution 6005/0 Unsigned8 ro no 0x02 Number of objects 6005/1 unsigned32 ro no Position measuring step µm 6005/2 unsigned32 ro no 100 Speed measuring step 0.01mm/s 6010 preset value This object supports adaption of the encoder zero point to the mechanical zero point of the system 6010/0 unsigned8 ro no 0x01 Number of available channels 6010/1 integer32 rw no 0x0 Preset value 6020 position value This object defines the output position value 6020/0 unsigned8 ro no 0x1 Number of available channels 6020/1 integer32 ro yes no Position value 6030 speed value This object defines the output speed value 6030/0 unsigned8 ro no 0x1 Number of available channels 6030/1 integer16 ro yes no Speed value 6200 cyclic timer unsigned16 rw no Corresponds to event timer (object 1800/5) 6500 operating status unsigned16 ro no 0x0 This gives information on encoder internal programmed parameters measuring steps unsigned32 ro no Position measuring step in µm Version /10 Änderungen vorbehalten / Specifications subject to change 5

6 9.4 Explanations to Object Library Object 0x1002 Manufacture Status Register Different to DS-301 chapter 2 the data type of the TIM CANopen sensor is unsigned8 instead of unsigned32. The definition of the manufacture status register is as follows: Byte7 Byte6 Byte5 Byte4 Byte3 Byte2 Byte1 Byte0 0 T E3 E2 E1 E0 S N N: Status 0 = sensor in error state 1 = normal running state (valid position and speed data transmitted) S: Start up 0 = normal running state 1 = start up or internal test mode E0: Magnet Error 0 = one magnet detected 1 = no or more than one magnet detected E1: Range Error 0 = no error 1 = the calculated position is out of range when also the position and speed value is set to zero 1 = the velocity value maybe not correct E2: Data flash error 0 = no error 1 = the CRC check of data flash parameter memory failed E3: Controller error 0 = no error 1 = the internal test routines detects an error T: Temperature µc 0 = T < Max temperature 1 = T > Max temperature 9.5 LSS / Layer Setting Service To configure the encoder via the LSS (according CiA DS-305) the encoder is handled as a slave, the PLC must have a LSS master functionality. A LSS-message is composed as follows: COB-ID DLC This applies to the COB-ID: LSS-Master LSS-Slave: 2021 (0x7E5) LSS-Slave LSS-Master: 2020 (0x7E4) LSS can only be used when the encoder is in the stopped status or pre-operational status. The NMT command for setting the encoder in stopped status is: COB-ID DLC 0x7E5 8 0x04 0x00 0x00 0x00 0x00 0x00 0x00 0x00 To program via LSS the sensor has to be switched to LSS configuration state. There are two possible ways to do so: Switch Mode Selective: only the addressed CANopen device is switched to the LSS configuration state LSS requires data content in the following objects: Example: Vendor-ID (see index 1018/1) 0x0182 LSS-Command 0x40 Product code (see index 1018/2) 0x0BE0 LSS-Command 0x41 Rev.No. (see index 1018/3) 0x10003 LSS-Command 0x42 Serial-No. (see index 1018/4) 0x LSS-Command 0x43 Version /10 Änderungen vorbehalten / Specifications subject to change 6

7 After receiving the identification objects, the encoder answers with LSS-Command 0x44. 0x7E5 8 Rx 0x40 0x82 0x01 0x00 0x00 0x00 0x00 0x00 0x7E5 8 Rx 0x41 0xE0 0x0B 0x00 0x00 0x00 0x00 0x00 0x7E5 8 Rx 0x42 0x03 0x00 0x01 0x00 0x00 0x00 0x00 0x75E 8 Rx 0x43 0x78 0x56 0x34 0x12 0x00 0x00 0x00 0x7E4 8 0x44 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Switch Mode Global: all CANopen devices supporting LSS are switched to the LSS configuration state 0x7E5 8 Rx 0x04 0x01 0x00 0x00 0x00 0x00 0x00 0x00 When the CAN devices are in configuration state the Node-ID and/or the baud rate can be changed Configuration of Node-ID When programming the Node-ID only one slave may be connected. The Node-ID can be programmed with the LSS-Command 0x11 N ID: new Node-ID in the range of Err Code: 0: protocol successfully completed / 1: Node-ID out of range 0x7E5 8 Rx 0x11 N ID 0x00 0x00 0x00 0x00 0x00 0x00 0x7E4 8 0x11 Err Code 0x00 0x00 0x00 0x00 0x00 0x00 Change of Node-ID will cause: Automatic alteration of COB-ID s for SDO, EMCY, Heartbeat and TPDO. Non-volatile Node-ID storage through Store Configuration in the LSS mode configuration Configuration of Bit Rate The Bit Rate can be programmed with LSS-Command 0x13 Table Index: 0x09: 10 kbaud 0x08: 20 kbaud 0x06: 50 kbaud 0x04: 125 kbaud 0x03: 250 kbaud 0x02: 500 kbaud 0x01: 800 kbaud 0x00: 1000 kbaud Err Code: 0: protocol successfully completed 1: Bit timing not supported 0x75E 8 Rx 0x13 0x00 Table 0x00 0x00 0x00 0x00 0x00 Index 0x74E 8 0x13 Err Code 0x00 0x00 0x00 0x00 0x00 0x00 The baud rate gets active after receiving the Activate Bit timing parameters command or after the Store Configuration Data command with the next Power on Reset Activate Bit timing parameter With the LSS-Command 0x15 the LSS master shall activate the bit timing defined by the configure bit timing parameters service. 0x75E 8 Rx 0x15 Switch delay 0x00 0x00 0x00 0x00 0x00 Switch delay: Time in ms internal multiplied by 2 when the new bit timing parameters become active. Note: No communication should be performed until the (2*switch delay) time runs out. Version /10 Änderungen vorbehalten / Specifications subject to change 7

8 9.5.4 Store Configuration Data The LSS configuration data (Node-ID and Bit Rate) are stored to the non-volatile memory of the sensor using LSS-Command 0x17 Err Code: 0: protocol successfully completed 2: storage media access error 0x75E 8 Rx 0x17 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x74E 8 0x17 Err Code 0x00 0x00 0x00 0x00 0x00 0x SDO Services Service Data Objects SDO (according to CiA DS-301) manage the parameter data exchange, e.g. the non-cyclical execution of the preset function. Parameters of device object library (object index/subindex see chapter 9.3 Object Library) can be read, written or stored by means of SDO SDO Download The SDO download service is used to configure the parameters. Command 0x2_: 0x22 0x23 0x27 0x2B 0x2F Command 0x60: write command, parameter to encoder write command, 4 Byte parameter to encoder write command, 3 Byte parameter to encoder write command, 2 Byte parameter to encoder write command, 1 Byte parameter to encoder confirmation: parameter received Index: Subindex: Object dictionary parameter index Object dictionary parameter subindex 0x600+Node-ID 8 Rx 0x2_ Index Subindex 0x580+Node-ID 8 0x60 Index Subindex Data Data Data Data LSB MSB 0x00 0x00 0x00 0x00 Example: object index 0x1010 subindex 01 store all parameters 0x600+Node-ID 8 Rx 0x23 0x10 0x10 0x01 0x73 0x61 0x76 0x65 0x580+Node-ID 8 0x60 0x10 0x10 0x01 0x00 0x00 0x00 0x00 Example: object index 0x1011 subindex 01 restore all parameters 0x600+Node-ID 8 Rx 0x23 0x11 0x10 0x01 0x6C 0x6F 0x61 0x64 0x580+Node-ID 8 0x60 0x11 0x10 0x01 0x00 0x00 0x00 0x00 Example: object index 0x100B subindex 0 set new node-id with 64 0x600+Node-ID 8 Rx 0x23 0x0B 0x10 0x00 0x80 0x00 0x00 0x00 0x580+Node-ID 8 0x60 0x0B 0x10 0x00 0x01 0x00 0x00 0x00 NODE-ID Using writing to object 0x100B, non-volatile storage has to be done by writing the save - signature (0x ) on object 0x1010/1. These changes will become effective after a communication restart or a power up. Changing the Node-ID will affect all COB-IDs according to the predefined connection set. Example: COB-ID TPDO = 0x180 + (Node-ID) Version /10 Änderungen vorbehalten / Specifications subject to change 8

9 9.6.2 SDO Upload The SDO upload service is used to read the parameters. Command 0x40: Command 0x4_: 0x42 read command, parameters from encoder read command, parameter to encoder Index: Subindex: Object dictionary parameter index Object dictionary parameter subindex 0x600+Node-ID 8 Rx 0x40 Index Subindex 0x580+Node-ID 8 0x42 Index Subindex 0x00 0x00 0x00 0x00 Data LSB Data Data Data MSB SDO Abort If the SDO download or SDO upload service fails for any reason, the sensor responds with a SDO abort protocol. Abort Code: 0x subindex does not exist 0x value exceeded 0x object does not exist 0x object is write only 0x object is read only 0x data transport error 0x general error 0x wrong state 0x580+Node-ID 8 0x80 Index Subindex Abort code 9.7 Process Data PDO Process Data Objects (according CiA DS-301) manage the process data exchange, f.e the cyclical transmission of the position value. The process data exchange with the CANopen PDOs is a very slim process without protocol overhead PDO Setting One Transmit PDO (TPDO) with max. 8 bytes is provided: 0x1800 TPDO1: default: asynchronous with event timer switched on (changeable to synchronous) Subindex 1: COB-ID PDO. The PDO can also be disabled with this parameter: Bit number Value Meaning 31 (MSB) 0 PDO exists/valid 31 (MSB) 1 PDO does not exist / is not valid 10-0 (LSB) X Bits of PDO COB-ID Subindex 2: The transmission type defines the transmission character of the PDO: Transmission type PDO Transmission PDO Transmission RTR only synchronous asynchronous X 254; 255 X 252; 253 X X not valid reserved Version /10 Änderungen vorbehalten / Specifications subject to change 9

10 Synchronous mode: When the sensor is in NMT operational state and the transmission type is between the synchronous mode is enabled. The PDO is transmitted by the sensor after receiving every n th SYNC object. The SYNC object has the following format: Byte0 Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 0x080* 0 Rx * The COB-ID of the SYNC object message can be individually programmed with Index So the COB-ID of the SYNC message can be different. Asynchronous mode: If the transmission type is set to 254 or 255 the PDO transmission is asynchronous from the SYNC object. The PDO is transmitted after the event timer (index 1800/5) or cyclic timer (index 6200) is expired. Both objects control the same timer. Event timer meaning: 0: PDO transmission disabled : PDO transmission in [ms] Polling with remote frames The polling of the PDO data with remote frames is independent from the transmission type (Index 1800/2). The PDO is transmitted by the sensor after receiving the corresponding PDO remote frame. The PDO remote frame has the following format: PDO COB-ID + RTR bit Byte0 Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 0 Rx PDO message format The PDO message mapping is described in Index 1A00. 0x180 + Node-ID 6 Position LSB Byte0 Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Position Position Position MSB Speed LSB Speed MSB- - - For the PDO message the actual measuring steps for the position and speed values can be read with object linear encoder measuring step settings (Index 6005). 9.8 Error Handling Emergency objects are triggered by the occurrence of a sensor-internal error. An emergency object is transmitted only once per error event. If one or all errors are repaired, the device transmits an emergency object with the error code 0x000 reset error / no error. This message contains also error register with the remaining errors Emergency Messages COB-ID EMCY DLC Rx/ 0x80+Node-ID 8 Emercency Error Code (see next table) COB-ID EMCY in object 0x1014. Byte0 Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Error Register Object 0x1001 0x00 0x00 0x00 0x00 0x00 Version /10 Änderungen vorbehalten / Specifications subject to change 10

11 Two Error conditions are defined: 0x50xx Device Hardware Error and 0x63xx Data Set Error Error-Code Error- Register Byte 0,1 Byte 2 Description 0x0000 0x00 Sensor Error resetted, no Error 0x5000 0x81 Device Hardware Error Cause: The Device Hardware Error is send when the microcontroller detects no stop pulses during one measuring cycle and when the Error Counter runs out. 0x6300 Data Set Error Cause: The Data Set Error is send by the sensor when the internal test function detects a mismatch between the new calculated and the stored checksum of the non-volatile memory of the sensor. The checksum is checked during the NMT Initialisation state. The checksum is also checked when the LSS Store Configuration Data command or a valid SDO download to Object 0x1010 (store parameters) is received. This error can only be cleared by a reset of the device and a successful checksum comparison in the new initialization state. 0x01 Data Set Error 0x081 Device Hardware Error and Data Set Error 9.9 Error Control Service Through error control services the NMT detects failures in a CAN-based Network. When the error control service is enabled the TIM CANopen sensor cyclically transmits a heartbeat message. One or more heartbeat consumer receives the indication. The relationship between producer and consumer is configurable via the object dictionary by SDO. By default the heartbeat is disabled. The first byte of the heartbeat message contains the actual network management state of the sensor. State: 0x00 Bootup 0x04 Stopped 0x05 Operational 0x07F Pre-operational Heartbeat protocol: COB-ID EMCY DLC Rx/ Byte0 Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 0x700+Node-ID 1 State 9.10 Non-Volatile Storage and Data Restoration Default values for all data objects are stored in the non-volatile program memory. Data encryption to the non-volatile memory is only admitted in the pre-operational status. Storage via LSS: Data must be stored through the LSS Service Configuration/Store while in LSS Configuration Mode (see chapter 9.5 LSS / Layer Setting Service) Storage via SDO: Object 0x1010: Data is stored in the non-volatile memory during encryption of object 0x1010 with save signature (0x ). Object 0x1011: Encryption of object 0x1011 with the signature load (0x64616F6C) will upload data from the non-volatile memory. Default settings are being restored (see chapter 9.6 SDO Services). Version /10 Änderungen vorbehalten / Specifications subject to change 11

12 9.11 Abbreviations CAN ch COB-ID const DLC DS EMCY NMT PDO Pos ro rw Rx RTR SDO SYNC TPDO Controller Area Network channel Communication Object Identifier constant parameter, only readable Data Length Code Draft Standard Emergency Service Network-Management Process Data Object Position (value) read only, parameter can change read/write Novotechnik sensor is consumer of the CAN data frame Remote Transmission Request Service Data Object Synchronisation message Transmit Process Data Object Novotechnik sensor is producer of the CAN data frame 9.12 Document Changes Revision Changes Date Who V_00 First edition VM/mm V_01 V_02 V_03 V_04 V_05 Version /10 Änderungen vorbehalten / Specifications subject to change 12