Contact Ethernet Converter module Installation and programming reference

Transcription

1 Contact Ethernet Converter module Installation and programming reference Features: Encrypted Ethernet communication 24 hour, two way connection to the Monitoring Station 4 programmable and remotely controlled Open collector output Local programming by serial port or through Ethernet port Remote programing throug IP networks (Internet) Industrial signal transmission through serial port or throug contact inputs External security panel DTMF Contact ID conversion to Ethernet Web programming. Page 1

2 Page 2

3 1.0. DEC module hardware description 1.1. Main parts: Outputs: Max output load is 200mA per output Wiring of the outputs: RS 232 connector: 1. Fixing holes 2. Ethernet connector 3. RS232 port 4. Input terminals 5. Output terminals 6. Output status LEDs Input terminals: + Positive 12 V DC GND Negativ Z1-Z4 Double EOL inputs Terminal for the phone input and outputs. + Positive voltage for the outputs O1-O4 Open collector terminals Line Incoming PSTN line Phone External device with communicator or telephone handset. Dec modules are available for serial communication for more information please contact your dealer or the manufacturer Specification: Woltage: Max current consumption: Size of pcb (L x W x H) Size of terminals: RS 232 connector: Ethernet connector: VDC 35mA (+OC) 133 x 68 x 19mm Ø2,5 mm Stand. 9 pins Stand. 8 pins Kommunication: 128 bit encrypted Outputs: max. 200 ma Inputs: 2,2 K vagy 3,3 K +/-10% User name: Admin Password: admin Inputs: Wiring of the inputs: Input: Marking on the panel Z1 Z2 Z3 Z4 Zone Number EOL Input 1 2,2K Input 2 3,3K Input 3 2,2K Input 4 3,3K Input 5 2,2K Input 6 3,3K Input 7 2,2K Input 8 3,3K Page 3

4 2.0. Installation of the board 2.1. Fixing and connection. 2. Open an internet browser like Mozzilla Firefox or Internet Exprorer. 3. Type into the browser field the IP address and port ( :8080) 4. If connection is successfull than you will see the following entry page. To enter, clock Login 1. Fix the panel by the four fixing holes 2. Connect the in and output wires. 3. Connect Ethernet and Serial cable 4. Check wires. 5. Connect Power. 6. Program the panel Configuring and checking the panel The panel has a built in web server, so it could be programmed by a standard web browser like Firefox or IE, there is no separate programming software. Remote access could be done through built in web server First connection to the panel: Us the fix, factory default IP address to connect to the panel. For this the computer with the browser must be ont he same internal network as the module. 1. Connect the computer directly or through Local Area Network (LAN) 5. Type the factory default User name and Password User Name: Password: Admin admin 6. After successull entry you will see the Status window : Page 4

5 3.2. Programming: Change the factory setting by enter into Configure section. IP address: This is the several IP. This aress is used for remote programming or remote controlling. Netmask: It is for to be able to distinguish between IP address and identification parts for IP packet receivers. Gateway: This is a device which is in connection with more TCP/IP network. It is for routing and forwarding different IP packets between these networks. For example a router address within the network is designated to.gateway. Nameserver: This is a name servert he server of the service provider. Write the provider server address into this field. ( A router could be also a name server) DTMF ID: DEC module is capaple to receive Contact ID codes from external security control panel. Here you can determine what to dial to send security panel reports through DEC module. In case of dial attempt from the external device the numbers matching the numbers the security panel dials than DEC sends Handshake signal and ready to receive CID codes. If the dialled and the pre-programmed number is not matching DEC will re-route the dialling attempt to the connected available PSTN line. PSTN lines should be connected to LINE inputs and standard phonesets and external control panel must be connected to the Phone output of DEC module Network: This is the position where you may set network parameters. Next time you may connect the panel according to the parameters you type in. Administrator password: The entry password could be changed here, max 16 character long password could be used Factory default: admin Warning: - If you loose your new password only manufacturer can reset the factory default password. If you mistype the password, you have 3 consecutive tries only, than the panel will not respond to it anymore. - This could be re-setted by power on-off procedure. Warning: Choose telefon numbers does not interfere with other numbers dialled on the standard telco lines.. Network Mode: Choosing the network connection: - Fix IP address - Dynamic IP address If you use dynamic IP, its still advised to use one fix IP in case if DHCP service would be not available. In this case the module will change to Fix IP address. Page 5

6 Connection: #1 Server address: The IP address of the Monitoring Station. Please contact your Installer or Monitoring Station. #1 Server Port number: This is the port number of the IP address. Please contact your Installer or Monitoring Station. #1 Modul ID: It is an unique ID number to be used for routing module datas. Az #2 vel jelölt szer: Secondary server parameters. Setting similar as above. Test sign interval: The module is in continous connection with the monitoring station, but sends test signals in periodical time Inputs Input: Number of the input. Figyelmeztetés: To program an input please refer to point 1.0.1! Enabled: The thickbox is to be used to disable inputs are not used. Enable input: The disable input: Disabled input does not have to be closed by an EOL resistor. Point Num.: Alarms of the port will be transmitted and identified with this 3 digit number. Alarm CID: This code is to be sent in case of Alarm of the particular zone. Restore CID: This code is to be sent in case of Restore of the particular zone. In case of short circuiting input terminals both zone number belongs to this input will be sent as tamper alarm Outputs: Output: Number of the output. Type: - Not used: If you do not need an output please select this one. This output can not be even activated remotely. - Communication Fail: If modul has disrupted communication this output will be activated. - Zone follower: It will be activated if the selected input is violated. You must consider the additional output settings for operation. - Server control: The server will control this output remotely. Mode: The timing of output operation is set here. - Monostabi: One state output. It will be activated and the time will follow the timing of the port than return to normal. - Inverse: This is an inverse operation. The output is always active than return to inactive for the duration of the pre-set output timing. - Bistable: This is a two state output. It will be switched to its on or off position according the trigger condition. The state of the output will remain in that particular state where its switched to. No timing on this kind of output. Timer: Steps of seconds as required to operate the output. Zone num.: If the output is a zone input follower output select the particular output here. The operation timing depends on output timing not the input alarm time. In case of Bi-Stable mode the output will follow timing of the selected input timing Save changes button All changes must be saved to change operating parameters of the module. By pressing this button the module will be re-started. Page 6

7 4.0. Status request and output remote controlling. The module could be found ont he IP address as pre-set in configuration page Status description Conecction Network status: The momentary status of the central station server Input/Otput Status of in and outputs Input: Number of inputs Status: Status if the momentary output condition. To see changes while browsing you should refresh the browser page. Output: Number of outputs State: Status if the momentary output condition. To see changes while browsing you should refresh the browser page Remote control of the outputs Output status could be changed by pressing the button near the output number. Change will be carried out immediately Hardware Hardware datas Version: The software version of the module Hardware ID: This is a factory pre-set, not changeable serial number of the module Contact If you click Contact you may send a pre-addressed message to the manufacturer Sky Laboratories. If you need further assistance please send us an or call us at numbers found on the installation manual. Uptime: The time since last re-start Network Networki parameters Ethernet address: The MAC address of the panel. Mode: The type of connection. IP address: The IP address of the panel Netmask: Network Identifier Gateway: The Gateway IP address which is used to communicate to the server. Nameserver: The server connection point or the the router itself. The module time is set by these devices. Page 7

8 Availability: Sky Laboratories Kft. Address: 2146 Mogyoród, Pf.: 16, Kerektó u. 2 Tel.: Fax: sales@skylaboratories.com Page 8