Aruba Mobility. Setup Guide

Transcription

1 Aruba Mobility Setup Guide

2 Disclaimer THIS DOCUMENTATION AND ALL INFORMATION CONTAINED HEREIN ( MATERIAL ) IS PROVIDED FOR GENERAL INFORMATION PURPOSES ONLY. GLOBAL REACH AND ITS LICENSORS MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THE MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE MATERIAL IS ERROR- FREE, ACCURATE OR RELIABLE. GLOBAL REACH RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES TO THE MATERIAL AT ANY TIME. Limitation of Liability IN NO EVENT SHALL GLOBAL REACH BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, DATA OR USE, INCURRED BY YOU OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT OR TORT, ARISING FROM YOUR ACCESS TO, OR USE OF, THE MATERIAL. VERSION 1.1 PUBLISHED APRIL 2015 Page 2 of 16

3 IMPORTANT - BEFORE YOU START Before attempting to integrate your hardware controller in to Odyssys, please ensure that ALL of the following requirements are in place; You have a controller installed in an environment where compatible Access Points are configured to work with the controller, i.e - DNS, DHCP options configured correctly Access points must be able to successfully obtain the configuration from controller Your client environment is configured to allow network clients to; Associate to an Access Point Obtain an IP address Access to the internet The following components are required to be configured and working in your environment before attempting integration with Odyssys; DHCP Server DNS Server Firewall NAT PLEASE NOTE - Odyssys does not use standard RADIUS ports, therefore please make sure you allow the ports in your firewall, defined in your manager.odyssys.net Captive Portal settings. This is a technical document and as such, integration of your hardware with Odyssys should only be handled by trained individuals. Page 3 of 16

4 GETTING STARTED WITH ODYSSYS Before configuring the Aruba Mobility Controller for use with Odyssys, you will first need to create a Captive Portal to obtain key settings for your Aruba Mobility Controller. 1. Within your Internet browser, navigate to 2. Login to Odyssys, using your Customer ID, Username and Password 3. Using the navigation panel on the left hand side of the Odyssys Dashboard, select "Captive Portals" then "Captive Portals" and finally "Create Captive Portal" 4. Enter the following details to create a new Captive Portal Name: <Name of your Captive Portal> Description: <Description of your Captive Portal> RADIUS Shared Secret: <Either keep the current shared secret or create your own> Hardware Vendor: Aruba Page 4 of 16

5 Click "Create" to save the settings and complete initial setup of the Captive Portal 5. Select the newly created Captive Portal and it will display the information required to configure the Aruba Instant Controller - Please note you may need to scroll down to see the information. TECH NOTE The information will differ for each Captive Portal created and is unique to each Captive Portal. Page 5 of 16

6 CONFIGURING ODYSSYS WITHIN ARUBA MOBILITY 1. Login to the Aruba Mobility Controller. 2. Click Configuration and then Campus WLAN. 3. Create a new AP Group for your WLAN if required by clicking New and entering a name for your AP Group and clicking OK. Page 6 of 16

7 4. Under WLANs click on New and enter in a name for your WLAN and click OK. 5. Click Next in the bottom right corner to continue to the next page of the Wizard. 6. Select Tunnel and click Next. 7. Select the following options and click Next. Radio Type: All Broadcast SSID: Yes VLAN: 1 (Or VLAN of your Network) 8. Select the Guest Radio button and click Next Page 7 of 16

8 9. Select "Captive portal with authentication via credentials provider by user" and click Next. 10. Ignore the next page and click Next to continue. 11. Click Add to specify an authentication server with the following settings and click OK. Name: Primary RADIUS IP Address: Auth Port: <This can be found in your Odyssys Captive Portal page> Acct Port: <This can be found in your Odyssys Captive Portal page> Shared Key: <This can be found in your Odyssys Captive Portal page> Retype Key: <This can be found in your Odyssys Captive Portal page> 12. Click Add again to specify the secondary authentication server with the following settings and click OK. Name: Secondary RADIUS IP Address: Auth Port: <This can be found in your Odyssys Captive Portal page> Acct Port: <This can be found in your Odyssys Captive Portal page> Shared Key: <This can be found in your Odyssys Captive Portal page> Retype Key: <This can be found in your Odyssys Captive Portal page> 13. Click Next and Finish to complete the Wizard Page 8 of 16

9 14. Select Stateful Firewall under Advanced Services on the left-hand side menu, then select the Destination tab and click Add. 15. Enter in the below settings and click Add. IP Version: IPv4 Destination Name: <Name of your choice> 16. Enter in the below settings and click Apply to save. Rule Type: Either host (for IP Address entries) or name (for Domain Name entries) IP Address/Domain Name: These can be found on page 13 under Access Control List Addresses Page 9 of 16

10 17. Click Authentication under the Security heading and then click L3 Authentication. 18. Click on Captive Portal Authentication and then the name of your Group you setup previously in the wizard. 19. Enter in the following settings and click Apply to save. Redirect Pause: 0 sec Logout popup window: Unticked Use HTTP for authentication: Ticked Login page: <Enter in the Splash Page URL from Odyssys> Welcome page: <Enter in the Success Page URL from Odyssys> Page 10 of 16

11 20. Click the AAA Profiles tab and then the name of your AAA profile that the Wizard setup. 21. Click RADIUS Interim Accounting tick box and click Apply. 22. Click RADIUS accounting server group from the left side menu and from the drop down menu, select the name of your WiFi group you created in the wizard. Page 11 of 16

12 23. Click New and select the Primary RADIUS from the drop down list, then click Add Server and repeat again for the Secondary RADIUS, click Apply once both have been added. 24. Associate the AP group to the Access Point and click Save configuration at the top to complete setup. The controller may require a reboot for the settings to come in to effect. Page 12 of 16

13 ACCESS CONTROL LIST ADDRESSES Odyssys Twitter api.twitter.com *.twimg.com Google Facebook *.facebook.com *.akamaihd.net *.fbcdn.net connect.facebook.com LinkedIn PayPal Express Checkout / / / / /32 If you wish to disable Apple's Captive Assistant please add the following to your walled garden captive.apple.com Page 13 of 16

14 FREQUENTLY ASKED QUESTIONS Q. I want to add different authentication provider types, how do I do this? A. Please see our Odyssys Authentication guide for further information. Q. I need more information on how to setup Odyssys A. Please see our Odyssys setup guide. Page 14 of 16

15 GLOSSARY ACL - Access Control List AAA - Authentication, Authorization, and Accounting DHCP - Dynamic Host Configuration Protocol DNS - Domain Name Service NAT - Network Address Translation PORT - A process-specific or an application-specific software construct serving as a communication endpoint, which is used by the Transport Layer protocols of Internet Protocol suite, such as User Diagram Protocol (UDP) and Transmission Control Protocol (TCP) RADIUS - Remote Authentication Dial In User Service (RADIUS) SHARED SECRET - A single password shared between two devices SSID - Service Set Identifier - A unique identifier for your Wi-Fi service WLAN - Wireless Local Area Network WLC - Wireless Local Area Network Controller Page 15 of 16

16 Craven House, 121 Kingsway London WC2B 6PA T +44 (0) info@globalreachtech.com Copyright Global Reach Technology Limited All rights reserved. Global Reach and the Global Reach logo are registered trademarks.