LBH-H/O-EAD-R-ICP LINK BRIDGE TM HBASET/HDMI RECEIVER SYSTEM WITH EXTERNAL AUDIO AND INLINE CONTROL PROCESSOR

Transcription

1 LBH-H/O-EAD-R-ICP LINK BRIDGE TM HBASET/HDMI RECEIVER SYSTEM WITH EXTERNAL AUDIO AND INLINE CONTROL PROCESSOR BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of their use or application. All rights reserved. 205 Broadata Communications, Inc.

2 SAFETY INSTRUCTIONS AND COMPLIANCE DECLARATIONS PLEASE OBSERVE THE FOLLOWING SAFETY PRECAUTIONS SURGE PROTECTION DEVICE RECOMMENDED This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Broadata Technical Support, 3

3 TABLE OF CONTENTS.0 PRODUCT DESCRIPTION OPERATION CONTROL AND FUNCTIONS RECEIVER EXTENDER FRONT AND REAR PANEL ICP FRONT AND REAR PANEL CONNECTOR PINOUT ASSIGNMENT EXTENDER SERIAL DATA INTERFACE STATUS LEDS ICP LB-KP LB-ICP WEB SERVER DESCRIPTION SPECIFICATIONS SERVICE PROCEDURE REPLACEMENT POLICY RETURN AND REPAIR SERVICE LIMITED WARRANTY Broadata Technical Support, (800)

4 .0 PRODUCT DESCRIPTION Overall A selectable HDBT or HDMI receiver with multiple control I/O ports Provides in-line control I/O paths Receiver Receive HDMI, audio, IR, and RS-232 up to 00 meters over CAT-5e/6 cable Supports video resolutions up to 080p 60Hz and 920 x 200@60Hz, as well as 4K@30Hz Supports HDMI w/embedded audio extraction EDID pass-through support, automatically detects the factory setting of the connected display Control Control I/O ports contain: - two (2) RS two (2) Relay - two (2) Digital I/O - one () IR - one () Ethernet Control and monitor AV devices using a standard Ethernet network (Smart phone or PC) or RS-232 (keypad) Front panel port status indicators User friendly customizable control configurations via built-in web server ORDERING INFORMATION LBH-H/O-EAD-R-M-SC-ICP Link Bridge HDBT/HDMI Receiver w/control I/O Ports Broadata Technical Support, Sales@Broadatacom.com 5

5 LBH-H/O-EAD-R-ICP User Manual 2.0 OPERATION CONTROLS AND FUNCTIONS ICP Extender Front In Out I / O 2 2 RS232 REM IR 2 2 RELAY NO NO C C NC NC +5V In Out AUX SPDIF AUDIO L / R PWR/ LINK HDMI IN DATA Out HDMI AUTO OPT In LBH-H/O-EAD-RX-ICP DATA IR HDMI OUT Extender ICP Rear +24VDC.25 A Out IR In LINK ON SW CONFIG LAN RESET 2. Receiver Extender Front and Rear Panel Front In Out I / O 2 2 RS232 REM IR 2 2 RELAY NO NO C C NC NC +5V In Out AUX SPDIF AUDIO L / R PWR/ LINK HDCP SPDIF HDMI IN DATA L/R EDID Loc Rem Out HDMI AUTO OPT In LBH-H/O-EAD-RX-ICP DATA IR HDMI OUT Rear +24VDC.25 A Out IR In LINK ON SW CONFIG LAN RESET 4 5. Power/Link: The red LED indicates the unit is powered up. The green LED indicates that the unit has a good HDBT connection. 6 Broadata Technical Support, (800)

6 5 2 2 LBH-H/O-EAD-R-ICP User Manual 2. HDCP LED: The blue LED is lighted when HDCP video is present. The blue LED blinks when non-hdcp video is present. 3. SPDIF LED: Lighted when corresponding SPDIF audio is active. 4. DATA LEDs: Lighted when corresponding input or output ports are active. 5. L/R LED: Lighted when corresponding audio is active. 6. DATA: RS-232 pass-through data connector. 7. IR: IR pass-through IR connector. 8. SPDIF: SPDIF audio output connector. 9. L/R: L/R audio output connector. 0. HDMI IN: HDMI video input connector.. HDMI OUT: HDMI video output connector. 2. EDID Selection: Select Local or Remote EDID (for HDMI IN) 3. Input Video Selection: Select input from HDMI, HDBaseT or Auto-dection. 4. HDBT: HDBT CAT-5e/6/7 cable connector. 2.2 ICP Front and Rear Panel ICP Front In Out I / O 2 2 RS232 REM IR 2 2 RELAY NO NO C C NC NC +5V In Out AUX SPDIF AUDIO L / R PWR/ LINK HDCP SPDIF HDMI IN DATA L/R EDID Loc Rem Out HDMI AUTO OPT In LBH-H/O-EAD-RX-ICP DATA IR HDMI OUT ICP Rear +24VDC.25 A Out IR In LINK ON SW CONFIG LAN RESET Digital I/O: Digital input/output ports. 2. Digital I/O LEDs: Light when the corresponding ports are active high. Broadata Technical Support, Sales@Broadatacom.com 7

7 3. RS-232: Serial port to control devices. 4. RS-232 LEDs: Light when the corresponding RS-232 ports are active. 5. REM LED: Light when the unit is set as a remote unit. 6. IR LED: Light when the IR out are active. 7. RELAY LED: Light when the corresponding, normally open pins, are closed. 8. RELAY: Normally open and normally closed relay ports. 9. AUX-In and AUX-Out: Reserved. 0. DC24V: DC power input connector.. IR Out: IR blaster port. 2. SW: The unit configuration dip switch 3. IR Learner: Built-in IR receiver for IR learning. 4. IR Learner LED: Lighted when the unit is IR learning mode. 5. CONFIG: Configuration/keypad port 6. LAN: Ethernet connector. 7. RESET: Press the button to reset the device back to factory default settings. 3.0 CONNECTOR PINOUT ASSIGNMENT 3. Extender 3.. Serial Data Interface Each LBH-H/O-EAD-R-ICP unit can be used for RS-232 and IR interface. RS-232/ IR Data The LBH-H/O-EAD-R-ICP transmits two channels of data signals. Follow the procedures for installing data terminal devices.. Label and connect one serial data cable to the user s RS-232 or IR device. 8 Broadata Technical Support, (800)

8 5 2 2 LBH-H/O-EAD-R-ICP User Manual 2. Connect the other end of this cable to the front panel data terminal block connector on the LBH-H/O-EAD-R-ICP (see below). RS-232/IR Terminal block pinout 3..2 Status LED s Additional status LED s are provided for the user to indicate the presence of HDCP video, audio presence and data presence. These are to assist the user in identifying right from the front panel whether a given signal is present for transmission and aid in the troubleshooting process if a given signal is missing. HDCP LED: Will be solid LED when video input has a HDCP. It will blink when video input does not have HDCP. Data in and Data out LED: It will be on when the unit detects data signal. In Out I / O 2 2 RS232 REM IR 2 2 RELAY NO NO C C NC NC +5V In Out AUX SPDIF AUDIO L / R PWR/ LINK HDCP SPDIF HDMI IN DATA L/R EDID Loc Out In HDMI OPT Rem AUTO LBH-H/O-EAD-RX-ICP DATA IR HDMI OUT SPDIF & L/R detect LED. It will be on when the unit detect the audio input signal. Broadata Technical Support, Sales@Broadatacom.com 9

9 3.2 LB-ICP Digital I/O CH- GND Digital I/O CH-2 GND GND Front RS-232 IN CH- RS-232 IN CH-2 Digital I/O LEDs =I/O Ch- 2=I/O Ch-2 } On=High Level Remote LED (On=Remote) IR TX LED (On=IR TX Act.) Relay Normally Open Relay Common Relay Normally Closed Reserved/Do Not Connect Reserved/Do Not Connect GND RS-232 OUT CH- RS-232 OUT CH-2 2=CH-2 Activity =CH- Activity RS-232 LEDs 2=Relay 2 ON =Relay ON Relay 2 Normally Open Relay 2 Common Relay 2 Normally Closed Reserved/Do Not Connect Reserved/Do Not Connect 0 Broadata Technical Support, (800)

10 IR OUT for external emitter IR detector behind holes Rear DIP SW Position : Local/Remote (Local=OFF) Position 2: Reserved Position 3: Reserved Position 4: Reserved IR Learn LED (ON in IR Learn mode CONFIG/Keypad. +2V keypad power 2. RS-232 IN 3. RS-232 OUT 4. GND Reset button: push to reset to default settings RJ-45 - TX+ 2 - TX- 3 - RX+ 4 - N/C 5 - N/C 6 - RX- 7 - N/C 8 - N/C 3.3 LB-KP8/LB-KP4 Rear Control RJ-45 Pin : RS-232 OUT Pin 2: RS-232 IN Pin 3: --no connect-- Pin 4: +2v Pin 5: +2v Pin 6: --no connect-- Pin 7: GND Pin 8: GND Broadata Technical Support, Sales@Broadatacom.com

11 The cable connection between LB-KP8 and LB-ICP is shown below. +2VDC IR Out ON SW IR Learner. Blue (+2V) 2. White / Orange (RS232 In) 3. Orange (RS232 Out) 4. Brown (Ground) CONFIG LAN RESET. White/Orange 2. Orange 3. White/Green 4. Blue 5. White/Blue 6. Green 7. White/Brown 8. Brown Standard RJ45 Termination T-568B 2 Broadata Technical Support, (800)

12 4.0 LB-ICP WEB SERVER DESCRIPTION Introduction The ICP Web Server provides user friendly and intuitive web pages to configure the virtual keypad and automation functions within the ICP. It also provides web pages to manage the IR Learner and IR code import. A standard web browser can be used to access the web pages. Accessing Web Server The IP address of the ICP must be obtained in order to access the Web Server. There are 2 ways to obtain the IP address of an ICP. ) Use the IPCONFIG command in the Configuration Port Command Line Interface to display the unit s IP address. 2) Use the BCI PC Configuration Program Type in the unit s IP address in the web browser. The ICP Virtual Keypad page will be displayed. All 8 keys of the Virtual Keypad are unprogrammed by default. The keys are configured in the Configure Key Action page. Broadata Technical Support, Sales@Broadatacom.com 3

13 Before configuring the Virtual Keypad, the system first needs to be set up using the Configure System page. On the top menu bar, click Configure and then click System. This brings up the ICP Login page. In the ICP Login type in admin for the Userid and admin for the Password and then click Sign in button. The Configure System page will appear. See the following section for Configure System page details. Once logged in, the user is free to open any of the Configure or Settings pages. The default Password can be changed using the BCI Product Configuration program. 4 Broadata Technical Support, (800)

14 Configure System The Configure System page is used to configure the network keypad, virtual keypad, RS-232 channels, Digital IO channels and remote unit types. On the top menu bar, click Configure and then click System. The following page will be displayed. Broadata Technical Support, 5

15 Local Unit The first two lines in this panel show the Local unit type and software version. Below that is the address setup and status for the Network Keypad. The last 2 pull down menus are for selecting the virtual keypad size and enabling Auto Action Triggers. Network Keypad Address: Enter the IP address of the network keypad (LB-KP8E or LB-KP6E) if one is present in the system. Use the BCI Product Configuration program to discover the network keypad s IP address. Network Keypad Status: Shows type of network keypad connected to ICP. Virtual Keypad Size: Select 8 keys or 6 keys. 8 keys option: maximum of 0 actions per key. 6 keys option: maximum of 5 actions per key. Auto Action Triggers: Select Enable to enable the auto action triggers defined in the Configure Auto Action page. Select Disable to disable all auto action triggers. Local Unit RS-232 Options This panel is used to configure the local RS-232 channels. Channel: Select channel, 2 or 3. Note: Channel 3 is only available on LBC-ICP and EAD/SCL-ICP units. Channel /2: RS-232 control channels. Channel 3: RS-232 control channel or pass-through channel. Channel 3 defaults as a control channel. Set Remote Connection (Remote Unit panel) to Disable in order to configure Channel 3 as a pass-through channel. Channel 3 (Remote) is the pass-through channel on the remote unit. Baud Rate: Select a baud rate from 9600 to 5200 baud. 6 Broadata Technical Support, (800)

16 Flow Control: Select On to enable flow control and Off to disable flow control. Flow control is available only on Channel. If flow control is enabled, Channel 2 is no longer available. End of Line Pattern: Select CR or CR+LF for end of line termination. Local Unit Digital IO Options The 3 pull down menus in this panel are used to configure the Digital IO settings. Digital IOs are inputs by default and show up as triggers in the Configure Auto Actions page. Digital IO Channel: Select channel or 2. Digital IO Direction: Select channel as a digital Input or Output. If the Digital IO Direction is set to Input, there is an option for Pullup Resistor. Pullup Resistor: Select Enable or Disable pull-up resistor. If the Digital IO Direction is set to Output, there is an option for Digital Output Mode. Digital Output Mode: Select TTL for a 5V compatible TTL type output or Open Collector for an open collector type output. An open collector type output can be used to implement a contact closure type output. For example, if a digital output is set to Open Collector, setting the Digital Output State to (High) will emulate a switch closure to ground. Setting the Digital Output State to 0 (Low) will emulate a switch being open. The Open Collector output also has an option for a Pullup Resistor. Remote Unit This panel enables the connection with the remote unit and selects the remote unit type. This panel is not available if the Local unit type is Standalone ICP. Remote Connection: Select Enable to enable the connection with the remote unit. Select Disable to disable the connection with the remote unit and enable the RS-232 pass-through channel. RS-232 channel 3 (remote) will not be available. Broadata Technical Support, Sales@Broadatacom.com 7

17 Remote Unit: Select the remote unit type. The available remote unit types are LBx without ICP, LBx with ICP and EAD/SCL with ICP. Configure Key Action The Configure Key Action page is used to configure the keys on the virtual keypad. On the 8-key keypad, each function key can be defined as a macro for up to 0 different actions. On the 6-key keypad, each function key can be defined as a macro for up to 5 actions. The available actions are Relay, RS-232, IR and Telnet. Digital Output actions are only available if Digital IOs are configured as outputs in the Configure System page. On the top menu click Configure and then click Key Action. The following page will be displayed: Function Key: Select the function key F through F8 to be defined. Function Key Label: Type in a label name for the selected function key. Function Key Mode: Select Standard for a momentary type key. Only one set of actions is assigned to a Standard key. Select Toggle for a toggle type key. A Toggle key has two states: Press and Release. One set of actions is assigned to the Press state and another set of actions is assigned to the Release state. 8 Broadata Technical Support, (800)

18 Command Action: Select the action number to be defined. Action through Action 0 can be defined. Spacing: Enter the delay desired before the command action. Action Type: Select the action type. Available types are None, Relay, Digital Output, RS-232, IR, Telnet, H/O Control and Keypad. Relay Options Relay Channel: Select the relay channel or 2. Relay State: Select the relay channel state, On (contact closed between NO and COM) or Off (contact open between NO and COM). Broadata Technical Support, Sales@Broadatacom.com 9

19 Digital Output Options Digital Output Channel: Select the digital output channel or 2. Note: this option is not available if both Digital IO channels are set to Inputs in Configure System page. Digital Output State: Select the digital output state: (High) or 0 (Low). 20 Broadata Technical Support, (800)

20 RS-232 Options RS-232 Channel: Select channel, 2, 3, or 3 (Remote). Transmit String: Type in the text string to be transmitted. Strings are terminated with CR or CR+LF, depending on the selection made in Configure System page. Characters enclosed by <> will be transmitted as hex. For example to transmit 00h enter <00>. Broadata Technical Support, Sales@Broadatacom.com 2

21 IR Options IR Preset: Select from list of IR commands stored in memory. IR commands must be learned via Configure IR Code page or imported via Configure IR Import page. 22 Broadata Technical Support, (800)

22 Telnet Options Telnet ID: Select the telnet connection desired for telnet actions. The connections defined in Configure Telnet Connections page appear in this menu. Commands: Enter the command strings to be transmitted. Up to 4 different command strings can be defined. Select the check box if the response to one of the commands is to be used as an auto trigger. Broadata Technical Support, Sales@Broadatacom.com 23

23 H/O Control Options H/O Input Select: Select Auto, Optical/HDBT or HDMI. Auto: Select Auto input mode. Video input will be selected automatically, with priority given to the remote input. For example if sources are plugged into the remote input and local HDMI input, the remote input will be selected. If the remote source is unplugged, the video output will switch to the local HDMI input. Optical/HDBT: Select remote video input. Auto mode is disabled. HDMI: Select local HDMI video input. Auto mode is disabled. 24 Broadata Technical Support, (800)

24 Keypad Action Action: Select Press, Release or Release All Toggle Buttons Press: This action presses the key selected in Key Number menu. All associated actions for the key press state will be executed. Release: This action releases the key selected in Key Number menu. All associated actions for the key release state will be executed. Release All Toggle Buttons: This action sets all toggle keys to the release state without executing any actions. Key Number: Select a key number for the selected keypad action. Broadata Technical Support, Sales@Broadatacom.com 25

25 Configure Auto Action The Configure Auto Action page is used to configure a set of auto actions based on a selected trigger. Available triggers are Video Detect, Digital Input, Digital Input 2, RS-232 Channel, RS-232 Channel 2, Telnet Trigger and Telnet Trigger 2. The available actions are Relay, RS-232, IR and Telnet. Digital Output actions are only available if Digital IOs are configured as outputs in the Configure System page. All auto triggers work independently and can be triggered simultaneously. On the top menu click Configure and then click Auto Actions. The following page will be displayed: Trigger: Select the auto action trigger. Available triggers are Video Detect, Digital Input, Digital Input 2, RS-232 Channel, RS-232 Channel 2, Telnet Trigger and Telnet Trigger 2. Trigger When: For Digital Inputs, select High for the High signal trigger. Select Low for the Low signal trigger. For the Video Detect Line, the trigger options are Video Detect Line Asserted or De-asserted. For RS-232 triggers, enter the trigger string. Up to 2 trigger strings can be defined for each RS-232 channel. For Telnet triggers, select the telnet trigger and enter the trigger string. Up to 2 trigger strings can be defined for each Telnet trigger. Note: A telnet trigger needs to be associated with one or more telnet actions. The check box under the Commands box in Configure Key Action, Telnet Options panel must be selected. 26 Broadata Technical Support, (800)

26 Allow delayed actions checkbox: Select this box to allow a set of delayed actions to be overridden by the opposing trigger. For example: video detect asserted trigger overrides video detect de-asserted trigger actions. Refer to the Configure Key Action sections for the descriptions of action types. Configure IR Code The Configure IR Code page is used to learn and manage IR codes in the ICP. To learn an IR code, type in the label of the IR code in New Label and click the Learn button. Once IR Learn mode is initiated, the user needs to present an IR signal to the IR receiver port within 30 seconds. If a valid IR code is not presented within 30 seconds, the IR learn process will timeout and the process will need to be re-initiated. After an IR code is learned successfully, it will be stored in memory and appear in the IR Preset drop down menu. To test a learned IR code, select the IR code from the IR Preset menu and click Test button. Verify that the IR code works correctly on the target device. To delete an IR code from the IR Preset menu, select the desired IR code and click the Delete button. On the top menu click Configure and then click IR Code. The following page will be displayed: Broadata Technical Support, Sales@Broadatacom.com 27

27 Configure IR Code Import The Configure IR Code Import page is used to import an IR pronto code. Once a code is imported, it will be stored in memory and is available as an IR Preset. It can be tested in the Configure IR Code page. On the top menu click Configure and then click IR Code Import. The following page will be displayed: New Label: Enter a label for the IR code. Pronto Code: Enter the pronto code to be imported. Configure Telnet Connections The Configure Telnet Connections page is used to setup the telnet connections for telnet key actions and auto actions. The 2 telnet connection types are Persistent and Action. The Persistent connection is a permanent telnet connection between the ICP and the remote device. This type of connection is typically used for monitoring telnet status messages for the purpose of triggering auto actions. The Action connection is a temporary telnet connection. This type of connection is typically used for normal telnet actions. 28 Broadata Technical Support, (800)

28 On the top menu click Configure and then click Telnet Connections. The following page will be displayed: Connection Type: Select Persistent or Action. Telnet ID: Select Telnet- or Telnet-2. Telnet Connection Label: Enter a label for the telnet connection. Connection Status: This box shows the status of a persistent connection. Telnet Options IP Address: Enter IP address of telnet server. IP Port: Enter port number of telnet server. The default port number is 23. Broadata Technical Support, Sales@Broadatacom.com 29

29 UserName Prompt: Enter username prompt from telnet server. Leave blank if there is no username prompt. UserName: Enter user name required for log in. Leave blank if there is no username. Password Prompt: Enter password prompt from telnet server. Leave blank if there is no password prompt. Password: Enter password required for log in. Leave blank if there is no password. Command Prompt: Enter command prompt from telnet server. Only the last 9 characters of the command prompt are needed. Leave blank if there is no command prompt. Note: Select check box below if string is used as a one-time only greeting. Auto Trigger: Select Telnet Trigger or Telnet Trigger 2. This selection associates the telnet connection with Telnet Trigger or Telnet Trigger 2 used in Auto Actions. Tx Spacing: Enter the delay (seconds) before command is transmitted in Telnet Actions. Enter 0 if no delay is desired. 30 Broadata Technical Support, (800)

30 View and Manage Settings The View and Manage Settings page shows the current settings of the Key Action Definitions, Auto Action Definitions and IR Code Definitions. Click the Details button next to Key Action Definitions to display the Key Action settings details. Click the Details button next to Auto Action Definitions to display Auto Action settings details. Click the Details button next to IR Code Definitions to display the IR Code details. ICP settings are saved to a file on the local PC using the Save Settings button. ICP settings are restored from a file using the Restore Settings button. On the top menu click Settings and then click View and Manage Settings. The following page will be displayed: Broadata Technical Support, Sales@Broadatacom.com 3

31 Click the Key Action Definitions Details button and the following will be displayed: 32 Broadata Technical Support, (800)

32 Click the Auto Action Definitions Details button and the following will be displayed: Broadata Technical Support, 33

33 Click the IR Code Definitions Details button and the following will be displayed: 34 Broadata Technical Support, (800)

34 Click the Telnet Definitions Details button and the following will be displayed: Broadata Technical Support, 35

35 Examples Example #: This example configures the F key on the virtual keypad as a toggle key to turn on/off Relay channel. On the top menu click Configure and then Key Action. Configure F Key toggle-press action, to turn Relay channel On as follows: Click Submit Changes. 36 Broadata Technical Support, (800)

36 Configure F Key toggle-release action, to turn Relay channel Off as follows: Click Submit Changes. Broadata Technical Support, Sales@Broadatacom.com 37

37 On the top menu click Keypad. The following virtual keypad should be displayed: 38 Broadata Technical Support, (800)

38 5.0 SPECIFICATIONS VIDEO (TRANSMISSION) HDMI Connector Protocol Up to 60Hz or 920 x 60Hz or 4K@30Hz HDMI Female Plug DDC/EDID/HDCP Capable AUDIO OUTPUT (TRANSMISSION) Signal Format L/R Analog and SPDIF Audio Output Connector 3.5mm Stereo RS-232 (TRANSMISSION) Data Rate Connector IR (TRANSMISSION) Data Rate Connector Up to 57.6kbaud Terminal Block 30-60KHz Terminal Block HDBT (TRANSMISSION) Cable Type CAT-5e/6 or higher Number of Cables Connector/Distance RJ-45/Up to 00m ETHERNET (CONTROL) Channel Capacity Connector Female RJ-45 (integrated Activity and Link LEDs) Data Rate 0/00Base-T, half/full duplex with autodetect Protocols DHCP, HTTP, TCP/IP, UDP/IP, AUTOIP, Telnet Broadata Technical Support, Sales@Broadatacom.com 39

39 RS-232 (CONTROL) Channel Capacity 2 (no flow control) or (with RTS/ CTS flow control) Baud Rate 2400 to 5200 baud (9600 baud=default), 8 data bits, stop bit, no parity Connector Terminal block DIGITAL I/O (CONTROL) Channel Capacity Digital Input Digital Output Connector 2 digital input/output (configurable) Input voltage range: 0 to 5 VDC Programmable pullup: 2.2k ohms to +5 VDC Threshold low to high: 2 VDC Threshold high to low: 0.8 VDC Output voltage high: 3 VDC min Output voltage low: 0.55 VDC max (64 ma sink max) Programmable open collector Terminal block IR (CONTROL) Channel Capacity Connector Carrier Frequency IR Learning in and out 3.5 mm jack (for IR blaster) 30 khz to 60 khz (Output) 30 khz to 60 khz (IR learning) 2 inches captive distance from panel RELAY (CONTROL) Channel Capacity Relay Contact Rating Connector 2 normally open/normally closed relays 24 VDC, A Terminal block 40 Broadata Technical Support, (800)

40 PHYSICAL Dimensions 8.36 (W) x 4.23 (D) x.2 (H) Power Consumption 24 Operating Temperature 0 to 40-deg C Humidity 0 to 95%, non-condensing Broadata Technical Support, Sales@Broadatacom.com 4

41 6.0 SERVICE PROCEDURE 6. Replacement Policy Standard products found defective on arrival (DOA) will be replaced, based on availability, within 24 to 48 hours anywhere in the U.S. Please call Customer Service at for information. 6.2 Return/Repair Service The Link Bridge LBH-H/O-EAD-R-ICP System contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/repair processing please contact Broadata Communications, Inc. to obtain a Return Material Authorization (RMA). Please include the following information: Product model number Serial Number Complete description of problem Hardware installation description Broadata Communications, Inc West 237th Street, Suite K Torrance, CA (30) (30) (Facsimile) CustomerService@Broadatacom.com Website: 42 Broadata Technical Support, (800)

42 7.0 LIMITED WARRANTY Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of shipment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI s election, by replacement, any said products that in our sole discretion prove to be defective and are returned to the manufacturing location within 30 days after such defect is ascertained. All warranties are limited to defects arising under normal use and do not include malfunctions or failure resulting from misuse, abuse, neglect, alterations, electrical power problems, usage not in accordance with product instructions, improper installation, or damage determined by BCI to have been caused by the Buyer or repair made by a third party. Limited warranties granted on products are to the initial customer end-user and are not transferable. OUR LIABILITY UNDER THIS WARRANTY SHALL IN ANY CASE BE LIMITED TO THE INVOICE VALUE OF THE PRODUCT SOLD AND BCI SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE USE OF ITS PRODUCTS OR THE SALE THEREOF. We make NO WARRANTY AS TO THE MERCHANTABILITY OF ANY GOODS, OR THAT THEY ARE FIT FOR ANY PARTICULAR PURPOSE OR END APPLICATION NOR DO WE MAKE ANY WARRANTY, EXPRESSED OR IMPLIED OTHER THAN AS STATED ABOVE. Broadata Technical Support, Sales@Broadatacom.com 43

43 44 Broadata Technical Support, (800)

44 Broadata Technical Support, 45

45 60000-LBHHOEADRICP Broadata Communications, Inc West 237th Street, Suite K Torrance, CA (30) (30) (Facsimile) CustomerService@Broadatacom.com Website: