Bluetooth V4.1 BLE RS-232 Serial Adapter Model: BLE-232B Bluetooth V4.2 BLE RS-232 Serial Adapter Model: BLE-232C

Transcription

1 Bluetooth V4.1 BLE RS-232 Serial Adapter Model: BLE-232B Bluetooth V4.2 BLE RS-232 Serial Adapter Model: BLE-232C Applications: MSR card reader reader, RFID reader, IC card reader, Specifications: 1. Baud Rate: Supports 1.2/2.4/4.8/9.6/19.2/38.4/57.6/115.2/230.4/460.8/921.6 Kbps 2. Default Baud rate: 9600 bps 3. Parity: none/even/odd 4. Stop bit: 1/1.5/2 5.Data bit: 7/8 6. Range: 30 m 7. Signal: TxD, RxD, GND, CTS/RTS 8. RS-232 Interface: D_SUB 9-pin female 9. Standard: Bluetooth specification version BLE V4.1/ V Profiles: GATT Serial 11. Frequency: to GHz 12. Tx. Power: Max. 3 dbm 13. Rx. Sensitivity: -89 dbm typical 14. Power Supply: 5~27VDC, 1.5A Max 15. Current Consumption: 100 mah (for reference) 16. Operation Temperature: 40 C to +85 C 17. Dimensions: 81.6 mm (L) x mm (W) x 17 mm (H) 18.Antenna Gain: Chip antenna max. 2 db (V4.2 only ) 19. V4.1 VS. V4.2 V4.1 V4.2 Data Payload 27 bytes 251 bytes Firmware Upgrade COM port COM port, OTA (Wireless) Application Short data transmission Bulk data transmission Remark: All contents are subject to change without notice

2 Architecture: Device Information SetCharacteristicNotification(Char) Firmware Revision String SetCharacteristicNotification (Char) SERIAL NOTIFY RxData SetCharacteristicNotification(Char) BLE_CONF MacID DeviceName DeviceName PinID_Setting Serial BLE Service Mobile APP Profile: LED light DIP Switch 5~27VDC 5V mini USB Reset DCE/DTE Switch - 2 -

3 RS232 Interface Pin Signal DTE Direction DCE Direction Description 1 CD Input Output Not connected 2 TxD Output Input Transmitted data 3 RxD Input Output Received data 4 DSR Input Output Contact manufacturer to set this 5 GND N/A N/A Signal ground 6 DTR Output Input Contact manufacturer to set this 7 CTS Input Output Clear to send 8 RTS Output Input Request to send (Default) 9 Vcc Input Input Power supply (5VDC, 1.5A Max.) DCE/DTE Switch(Rear side) DB9 DCE DTE DIP Switch(9 Pin) DB Stop Bit Parity Bit, Hi Bit Parity Bit, Lo Bit Baud Rate Switch DIP9 DIP8 DIP7 DIP6 DIP5 DIP4 DIP3 DIP2 DIP1 1:DIP setup 1:HWFC On 1:2 stop bits 00: No parity 01:Odd parity 1:Master mode 000:9600,001: :SW setup 0:HWFC Off 0:1 stop bit 10:Odd parity 11:Even parity 0:Slave mode 010:38400,011: :115200,101: :2400,111:

4 LED Light Data LED (Blue) Link LED (Green) Status Data LED blinking Data LED off Link LED on Link LED off Data LED on & Link LED on Description Data transmission No data transmission BLE Link No Link DFU/OTA Mode Power + Screws and nuts a. Screws up the base of machine b. To be nuts of the - 4 -

5 Programming Interfaces: GATT UUID_Device Information UUID_Firmware Revision String UUID_NOTIFY (~20 bytes) UUID_RxData (~20 bytes) UUID_BLE_CONF (7 bytes) UUID A F9B34FB 00002A F9B34FB F9B F9B F9B0132 Byte0 Byte1 Byte2 Byte3 Data bit Hwfc Stop Bit Parity Bit 7,8 0x01:on 0x00:off 2:1 3:1.5 4:2 0x02 : No Parity 0x01 : Odd Parity 0x00 : Even Parity Byte4 Byte5 Byte6 Baud Rate Device Mode Reset To Default 00: : : : : : : : : : : x01:on 0x00:off 0x01: Reset UUID_MacID (6 bytes) F9B0133 UUID_DeviceName (15 bytes) F9B0134 UUID_Reboot (1 bytes) F9B0135 UUID_PinID_Setting (6 bytes) F9B

6 Command set for BLE via serial port Command Value Description AT Check the connection status between control terminal and the RS-232 adapter. Response: OK when the connection is ok. Response: ERROR when the connection is not ok. AT Test the RS-232 status when first connect the adapter with the controller. BAUD= This command is used to specify the baud rate of COM port. The command will need 200 ms delay bps bps bps (Default) bps bps bps bps bps bps bps bps? Inquire the current baud rate. BIT= 7 7 data bit 8 8 data bit? Inquire the current data bit DEFAULT= This command is used to restore the default settings and originate a warm start. Y Restore the default settings (e.g bps). The command will re-start the system for 1 second. DFU= Device Firmware Upgrade via PC software. OTA (Over the air) is available to upgrade the firmware by APP Y ECHO= This command is used to specify whether the adaptor echoes characters received from the UART back to the DTE/DCE. N Command characters received from the UART are not echoed back to the DTE/DCE. (Default) Y Command characters received from the UART are echoed back to the DTE/DCE. FLOW= This command enable or disable flow control signals (CTS/RTS) of the UART port. Note, the setting is not affected by DEFAULT. The command will need 1 second delay. (Default) N Disable flow control. Y Enable flow control.? Inquire the current setting - 6 -

7 NAME= This command is used to specify a device name for the adaptor. You can specify a friendly name using 0 to 9, A to Z, a to z, space and, which are all valid characters. Note that first space or -, last space or isn t permitted. The default name is Serial Adaptor. (Default) BLE Serial Default device name xx.xx xx.xx is a character string with the length from 2 to 30. R Restore the default settings name= BLE Serial.? Inquire the name of the local adaptor. PARITY= This command is used to specify parity bit setting of COM port. The command will need 200 ms delay. (Default) N None parity bit O Odd parity E Even parity PIN= This command is used to specify a PIN code. The default PIN is Paired adaptors should have a same PIN. This command is used to specify a PIN. The default PIN is 1234 and the length is not smaller than 4. Paired adaptors should have a same PIN. The PIN code includes the numeral and English characters. (Default) xx.xx N xx.xx is a 4~16 digit string or English character (in capital or lower case) Cancel authentication by PIN. R Restore the default settings PIN= 1234.? Inquire the current PIN. PROMPT= The command is used to decide whether result messages are prompted when Setup commands are executed. The result messages are: OK/ERROR for command execution. (Default) Y Prompt result messages. N Not prompt result messages. STATUS= Inquire all the current setting of the adapter. T Inquire the inner temperature of the IC in centigrade? Display the current setting of the adapter STOP= This command is used to specify one or two stop bits of COM port. The command will need 200ms delay. (Default) 1 One stop bit. 2 Two stop bits. VERSION= This command is used to inquiry the firmware version.? Inquire the version codes