PCT-610/620 Remote Control Protocol

Size: px

Start display at page:

Download "PCT-610/620 Remote Control Protocol"

Lizbeth Sharp
5 years ago
Views:

1 INTER-M PCT-610/620 Remote Control Protocol Version INTER-M Remote Control Protocol PCT-610/620 1/12

2 Inter-M Corporation Agreement of Permit to Use Protocol Please read this Agreement of Permit to Use Protocol prior to using Inter-M s RS-232 Protocol (hereinafter, Protocol ). Downloading or viewing this document is considered as purpose of using Inter-M s Protocol and as consent of conditions as described below. Unless you cannot consent conditions of this Agreement, you cannot be permitted to use the protocol. 1. Use permit 1) Use of this protocol is permitted to customers purchasing of Inter-M s product using the protocol or authorized agency. 2) The term of Customer refers to individual, corporation which purchased Inter-M s product or authorized agency. 2. Copyright The copyright of this protocol belongs to Inter-M Corp., which is protected by the Korean Act of Copyright and applicable international treaty. 3. Prohibitions against COPY, DISTRIBUTE, MODIFY 1) Customer is prohibited from copying or reusing protocol contained in this document. 2) Customer shall not transfer, lease, consign this protocol or permit to use it in other corporation s protocol. 4. Period of use permit 1) If violating any contents as described in this agreement, "Customer" may be subject to cancellation of use permit. 2) If permit of use would be cancelled, Customer cannot use the protocol and shall immediately dispose this document, its copy or its additional materials. INTER-M Remote Control Protocol PCT-610/620 2/12

3 <Contents> 1 Summary Communication Definitions Structure of Protocol Data The Control signal protocol The Status response protocol...8 INTER-M Remote Control Protocol PCT-610/620 3/12

4 INTER-M Remote Control Protocol for PCT-610/620 1 Summary This document defines protocol for remote control using a RS-232 port of the INTER-M s PCT- 610/620 which is the main controller of conference system. The protocol consists of Control Signal Protocol and Status Response Protocol. If transmitting such Control Signal Protocol as defined hereunder to a RS-232 port of the PCT- 610/620, the PCT-610/620 performs operation according to the protocol received. If operation status is changed, the product transmits Status Response Protocol of the PCT-610/620 outside. The outside control equipment receives this signal and indicates it on the Display etc to check the operation status. The Status Response Protocol is transmitted outside when operating it by pressing any key of the PCT-610/620, when operating it with a remote control or when operating it with a RS-232 protocol. 2 Communication Definitions Communication UART(RS-232C) Baudrate Data Bit Stop Bit Parity 9600 bps 8 bit 1 bit No Parity INTER-M Remote Control Protocol PCT-610/620 4/12

5 3 Structure of Protocol Data 3.1 The Control signal protocol Control signal protocol is protocol transmitted in order to control of our IM-300 from the outside controller The Protocol Block Structure STX LEN DVID DATA CHK abbrevi ation Name Code Data Length Commentary STX START TX 0xFE 1 BYTE Transmission Start Byte. LEN Length 0x03 1 BYTE Length value of protocol transmitted after Length. (bite number from DVID to CHK) DVID Device ID 0x2B 1 BYTE Device ID of the PCT-610/620. DATA DATA Hex s 1 BYTE Data value necessary for performing function. CHK Checksum Hex 1 BYTE Checksum data to check whether received data are normal The Device ID Device ID 0x2B Function performance code data DATA 동작 0x01 POWER ON 0x02 POWER STANDBY 0x03 SELECT CD 0x04 0x05 SELECT TUNER 0x06~0x0F 0x10 TENKEY 0 INTER-M Remote Control Protocol PCT-610/620 5/12

6 0x11 TENKEY 1 0x12 TENKEY 2 0x13 TENKEY 3 0x14 TENKEY 4 0x15 TENKEY 5 0x16 TENKEY 6 0x17 TENKEY 7 0x18 TENKEY 8 0x19 TENKEY 9 0x10~0x1F 0x20 CD PLAY 0x21 CD STOP 0x22 CD PAUSE 0x23 FORWARD SEARCH START 0x24 BACKWARD SEARCH START 0x25 FORWARD SKIP START 0x26 BACKWARD SKIP START 0x27 GROUP 0x28 RANDOM 0x29 REPEAT 0x2A 0x2B FORWARD SEARCH STOP 0x2C BACKWARD SEARCH STOP 0x2D FORWARD SKIP STOP 0x2E BACKWARD SKIP STOP 0x2F~0x5F 0x60 TUNINIG UP START 0x61 TUNING DOWN START 0x62 PRESET UP START 0x63 PRESET DOWN START 0x64 PRESET SCAN 0x65 MEMORY 0x66 FM MUTE 0x67 MODE (STEREO/MONO) 0x68 BAND (FM/AM) INTER-M Remote Control Protocol PCT-610/620 6/12

7 0x69 0x6A 0x6B 0x6C 0x6D~0x9F 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA~0xFF TUNINIG UP STOP TUNING DOWN STOP PRESET UP STOP PRESET DOWN STOP MASTER Volume UP START MASTER Volume DOWN START MASTER Volume UP END MASTER Volume DOWN END Zone Select ALL Zone 1 Select Zone 2 Select Zone 3 Select Zone 4 Select Zone 5 Select INTER-M Remote Control Protocol PCT-610/620 7/12

8 3.2 The Status response protocol 1) This is protocol used when transferring values of changed operation status value of the CD Player and so that these values are displayed on the outer controller where display exists. 2) This protocol notifies status information to the outside controller so that the status information is displayed on the display of the outer controller, even when operation status of the CD player changes to the protocol received via communication, or when directly changing status of equipment in the main body of CD player or when changing status of equipment with a IR remote control Status Response Protocol Block Structure STX LEN DVID SYS 1CD1 1CD2 1CD3 TU1 PA1 PA2 CHK abbrevi Code Data Name ation Length Commentary STX START TX 0xFE 1 BYTE Transmission Start Byte LEN Length 0x09 1 BYTE Length value of protocol transmitted after Length (bite number from DVID to CHK) DVID Device ID 0x2B 1 BYTE Device ID of the PCT-610/620. US Hex SYS SYSTEM 1 BYTE The Information of the equipment. US Hex CD1 CD 1 1 BYTE Operation status information of CD US Hex CD2 CD 2 1 BYTE Track information upper byte of CD US Hex CD3 CD 3 1 BYTE Track information lower byte of CD US Hex TU1 TUNER 1 BYTE Operation status information of TUNER US Hex PA1 PA AMP1 1 BYTE Master Volume Information. INTER-M Remote Control Protocol PCT-610/620 8/12

9 PA2 US PA AMP2 Hex 1 BYTE Zone Select Status. CHK Checksum Hex 1 BYTE Checksum data to check whether received data are normal The bit structures of each Status information 1) SYS The Status of SYSTEM - - SYS SYSSRC PRTC SYSPW Bit 7 Reserve Bit 6 Reserve Bit 5 Bit 4 EM/TEL/RM/Normal Status. (Normal:00b, RM:01b, TEL:10b, EM:11b) Bit 3 Bit 2 1CD/6CD/TUNER/DECK Select Status (1CD: 00b, 6CD: 01b, TU: 10b, DECK: 11b) Bit 1 PROTECTION (ON: 1, NORMAL: 0) Bit 0 POWER (ON: 1, STANDBY: 0) 2) CD1 The Status of the CD Player - - 1CDGRP 1CDRND 1CDRPT 1CDPAU 1CDPS Bit 7 Reserve Bit 6 Reserve Bit 5 GROUP ON/OFF (ON: 1, OFF: 0) Bit 4 RANDOM ON/OFF (ON: 1, OFF: 0) Bit 3 Bit 2 CD REPEAT (OFF: 00b, REPEAT 1: 01b, REPEAT ALL: 10b) Bit 1 CD PAUSE (PAUSE: 1, RESUME: 0) Bit 0 CD PLAY/STOP (PLAY: 1, STOP: 0) INTER-M Remote Control Protocol PCT-610/620 9/12

10 3) CD2 The Track Information upper byte Upper byte of CD track number during play, selected track number and upper byte of total track number information CDTRH7~0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reserve Reserve Reserve Reserve Reserve Reserve Upper byte to represent 0 through ) CD3 The Track Information lower byte Lower byte of CD track number during play, selected track number and upper byte of total track number information. 1CDTRL7~0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Lower byte to represent 0 through 999 When CD is in play status - Shows track number value during playing. When CD is in stop status - Shows total track number information. When CD is in track selection status - Shows selected track number. INTER-M Remote Control Protocol PCT-610/620 10/12

11 5) TU1 The Operation Status of TUNER TUMUTE TUMODE TUBAND Bit 7 Reserve Bit 6 Reserve Bit 5 Reserve Bit 4 Reserve Bit 3 Reserve Bit 2 FM MUTE (ON: 1, OFF: 0) Bit 1 MODE (MONO: 0) Bit 0 BAND (FM: 1) 6) PA1 The Master Volume s - PAVOL0~6 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 of current Master volume (0x00(0) ~ 0x46 (70)) May vary depending on the scope of volume level (0~128) Bit 0 INTER-M Remote Control Protocol PCT-610/620 11/12

12 7) PA2 Zone Select Status - - PAZN5 PAZN4 PAZN3 PAZN2 PAZN1 PAZNA Bit 7 Reserve Bit 6 Reserve Bit 5 Zone 5 ON/OFF (ON: 1, OFF 0) Bit 4 Zone 4 ON/OFF (ON: 1, OFF 0) Bit 3 Zone 3 ON/OFF (ON: 1, OFF 0) Bit 2 Zone 2 ON/OFF (ON: 1, OFF 0) Bit 1 Zone 1 ON/OFF (ON: 1, OFF 0) Bit 0 Zone ALL ON/OFF (ON: 1, OFF 0) 3.3 Definition of CHECKSUM 1) Operation scope: All code values except for CHK. 2) Operation: Adopts code values within a given scope according to addition operation (+). 3) Ex) Checksum calculated when sending Power On protocol from outside controller to equipment PCT-610/620. A. Code s 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE STX LEN DVID DATA CHK 0xFE 0x03 0x2B 0x01 0x2D B. Equation checksum = STX + LEN + DVID + DATA = 0xFE + 0x03 + 0x2B + 0x01 = 0x2D INTER-M Remote Control Protocol PCT-610/620 12/12

INTER-M CD-611 Remote Control Protocol

INTER-M CD-611 Remote Control Protocol Version 1.0.0 INTER-M Remote Control Protocol CD-611 1/14 Inter-M Corporation Agreement of Permit to Use Protocol Please read this Agreement of Permit to Use Protocol