Kilotech. KRS SWP Series. Counter-top weighing scale. NTEP (USA) and Measurement Canada approved.

Size: px

Start display at page:

Download "Kilotech. KRS SWP Series. Counter-top weighing scale. NTEP (USA) and Measurement Canada approved."

Megan McCormick
6 years ago
Views:

1 Kilotech KRS SWP Series Counter-top weighing scale NTEP (USA) and Measurement Canada approved

2 KILOTECH KRS SWP series Weighing Scale NOTE: Le manuel en Français est disponible au Thank you for purchasing a Kilotech Model KRS SWP Weighing Scale. Please read all operating instructions carefully before using the scale for the first time. This scale is approved by the US and Canadian governments and can be used in a Legal for Trade application. If used in a Legal for Trade application, the scale must be inspected and sealed as per the local legislation. 1

3 Contents 1.0 Precaution before Using the Scale Environment Protection in the transportation Leveling the scale Turn on scale Explanation of Display Symbols Keypad Functions Operations Scale Parameters Setting Backlight type Auto shut. Off time Power Supply Error Message 9 2

4 1.0 Precaution before Using the Scale 1.1 Environment The scale should always be used for its intended use (see and its intended capacity. This scale is not protected against water; DO NOT spray with liquids as this could damage the electronics or could cause serious injury. To clean the scale, wipe it with a soft humid cloth and if necessary, use a non-abrasive household cleaner. The scale should always be used in an environment, which is free from excessive air currents, corrosives, vibration, and temperature or humidity extremes. These factors will affect displayed weight reading. DO NOT install the scale: l Next to open windows or doors causing drafts or rapid temperature changes. l Near air conditioning or heating vents. l Near vibrating, rotating or reciprocating equipment. l Near magnetic fields or equipment that generates magnetic fields. l On an unstable work surface l In a dusty environment l In direct sunlight. 3

5 1.2 Protection in the transportation Before the initial use, please refer to the following drawing to take off the protection screw. When packing the scale for transportation, install the protection screw on the scale in order to avoid any damage to sensitive components. 1.3 Leveling the Scale The scale is equipped with a level indicator on the left bottom side of the front panel and four adjustable leveling feet. Adjust the leveling feet until the bubble appears in the center circle of the indicator. Then lock the feet in place using the lock nuts. Repeat this procedure each time the scale is moved to a new location. 1.4 Turn on Scale Do not turn on scale with anything on the platform. The switch is located on the right side of the scale. The scale will start to count down from nine to zero and will display the max capacity of the scale in the display. The scale is then ready for use. Allow the scale15-30 minutes to warm up prior to use. 4

6 2.0 Explanation of Display Symbols LCD Display Meaning of the Symbols (Zero): Scale is in ZERO mode. NET: Scale is in TARE mode. : Low Voltage (Stable): Scale is in stable mode. kg/ lb: Indicates the current measuring units in weighing mode. 5

7 3.0 Keypad Functions Button Zero/Enter Function Zero the scale Accepts the current setting on the display. Move the settings backward in CAL parameter settings Move the settings forward in CAL parameter settings Select the options in settings Select the options in settings 4.0 Operations Turn on the scale; the scale will be in the weighing mode. Zero Function If the zero shifts during operation, press the ZERO/ENTER key to set it to zero. The Zero function is only active over a ±2%. Of capacity range. EXAMPLE: If you are using a KRS-SWP3 (3kg) scale, 2% x 3kg = 60g. If the scale is NOT in TARE mode AND platter is empty BUT the scale indicator reads between -60g and +60g, press the ZERO/ENTER key to reset the scale to zero. 6

8 5.0 Scale Parameters Setting Press and ZERO/ENTER key at the same time in weighing or counting mode to enter into parameters setting. 5.1 Backlight type Press or to set the backlight type to be bl. 1, bl. 2 or bl. 3. Please refer to the following. Backlight type bl. 1 bl. 2 bl.3 Description Automatic backlight Backlight is always on Backlight is off Press ZERO/ENTER key to confirm and return to next setting. 5.2 Auto Shut. off time Press or to set the auto shut. off time to be 0, 2, 5 or 8. Auto shut. off time Description A.OFF 0 The auto shut. off function is unavailable A.OFF 2 A.OFF 5 A.OFF 8 The scale will shut off automatically in 2 minutes The scale will shut off automatically in 5 minutes The scale will shut off automatically in 8 minutes Note: The auto off has been set to 0 on the KRS-SWP. The scale will shut off automatically only when the scale is unloaded and without any key being pressed. Press ZERO/ENTER key to confirm and exit from the parameter setting mode. 7

9 6.0 Power Supply & Battery Operation POWER SUPPLY DC 12V/1A 7.0 Error message During the initial power-on testing it is possible the scale may show error message. The meaning of the error messages is described below. Error codes Possible causes Remedy E1 EPROM data lose. Recalibrate the scale. E2 --OL-- The initial zero is outside the range of the factory setting for zero. Load exceeds scale capacity. 1. Check if there is something on the pan or something touches the top body when switch on the scale, move the load and switch on again. 2. Recalibrate the scale. Reduce the load on the pan System is busy. Just wait. LOBAT OFF Low voltage Change adaptor. If the error message is still displayed after above solutions have been tried, contact your dealer for further support. 8

10 If scale is misused or received in impact etc., re-calibration may be required. This should be done by a specialized scale professional. If your distributor is an industrial scale dealer, he will be able to do this for you. If you do not know who to contact, call the Kilotech customer service desk at (Canada) or (USA) and we will recommend someone. 8.0 Calibration Procedure Switch on the scale. And press the Calibration key at the bottom of the case during self-testing period. The display will show as below: CAL Press ENTER key to set the Capacity and Resolution, and then start weight loading procedure; Capacity The display shows as below: 9

11 kg C 3 Press or key to select the capacity to be: 3kg or 6kg. Press ENTER key to confirm and move to Resolution. Resolution The display shows as below: 3000 Press or key to select the resolution to be: 3000 or Press ENTER key to confirm and start weight loading. The display shows as below: L 0 kg 10

12 Press ENTER key to confirm the current zero point, and then the display shows the calibration weight value for the first time (1/3 of full capacity) which should be put on. L kg Put on the weight refer to the display. Press ENTER key when the display is stable to confirm. Then the display shows the calibration weight value for the first time (2/3 of full capacity) which should be put on. L kg Put on the weight refer to the display. Press ENTER key when the display is stable to confirm. Then the display shows the calibration weight value for the first time (3/3 of full capacity) which should be put on. L kg Put on the weight refer to the display. Press ENTER key when the 11

13 display is stable to confirm. Then the scale enters into parameters setup mode. Note: During the weight loading procedure, press or key check the internal count (Press again to return). Parameters setup The display shows as below: SET Press ENTER key to set the Auto zero tracking range. Auto zero tracking The display shows as below: az off 12

14 Press or key to choose the range to be off, 0.2e, 04e or 0.6e. (Default: 0.6e) Press ENTER key to confirm and move to Units selection. Units selection The display shows as below: U kg Press or key to select the unit: kg or lb. (Default: kg) Press ENTER key to confirm and move to Communication protocol type. Communication protocol type The display shows as below: TypE 0 Press or key to select the protocol type: type 0- type 7.2. (Default: type 0) Type0 and type1: Most P.O.S, ECRs and some TEC P.O.S. system 13

15 Type2: SHARP ER-Axxx, ER-A450T, New SANYO ECRs using RS-232 and others Type3: Most P.O.S. system Type4: CRS, NCR2170, SAMSUNG ER-5100, ER5115 and Many other ECRs Type5: NCI General, SAMSUNG ER5100, Most P.O.S. Software Type6: SAMSUNG ER-670 Type7.1: Continuous output Type 7.2: Output when stable (Once there is a weight change exceeds 1e, it will output) Note: For type0-type5, the Serial communication format is: Baud rate: 9600 Data bits: 7 Parity bit: Stop bit: 1 BIT EVEN BIT For type6-type7 (7.1 and 7.2), the Serial communication format is: Baud rate: 9600 Data bits: 8 BIT 14

16 Parity bit: Stop bit: 1 None BIT Press ENTER key to confirm. The calibration procedure is finished. The scale will re-start and enter into normal weighing mode. 15

Userʼs Guide. 1200g High Precision Scale. 1200g High Precision Scale. Legal for Trade. Includes RS-232 interface port. UG Version 1.

Userʼs Guide. 1200g High Precision Scale. 1200g High Precision Scale. Legal for Trade. Includes RS-232 interface port. UG Version 1. Userʼs Guide 1200g High Precision Scale Legal for Trade 1200g High Precision Scale Includes RS-232 interface port UG Version 1.2_12-30-13 !!!! CALIBRATION WARNING!!!! Calibration AND inspection of calibration