MS-890 Industrial Automation Scanner User Manual

Transcription

1 MS-890 Industrial Automation Scanner User Manual P/N Rev B

2 Copyright and Disclaimer Copyright 2015 Microscan Systems, Inc. Tel: / Fax: All rights reserved. The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and/or service Microscan manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Microscan. Throughout this manual, trademarked names might be used. We state herein that we are using the names to the benefit of the trademark owner, with no intention of infringement. Disclaimer The information and specifications described in this manual are subject to change without notice. Latest Manual Version For the latest version of this manual, see the Download Center on our web site at: Technical Support For technical support, helpdesk@microscan.com. Warranty For current warranty information, see: Microscan Systems, Inc. United States Corporate Headquarters / United States Northeast Technology Center / European Headquarters Asia Pacific Headquarters ii MS-890 Industrial Automation Scanner User Manual

3 Table of Contents Introduction Chapter 1 Quick Start Step 1 Check Required Hardware Step 2 Connect the System Step 3 Position Scanner and Symbol Step 4 Install ESP Step 5 Select Model Step 6 Autoconnect Step 7 Receive Settings Step 8 Calibrate Step 9 Test Read Rate Step 10 Configure the Scanner in ESP Step 11 Save Configuration in ESP Chapter 2 Using ESP EZ Mode Application Mode Menu Toolbar Autoconnect View Navigating in ESP Send/Receive Options Chapter 3 Communications Communications by ESP Communications Serial Commands RS-232/422 Host Port Host Port Parameters Host Protocol Poll Address ACK / NAK Options Polling Mode Options Auxiliary Port Protocol Daisy Chain Autoconfigure Daisy Chain Scanner ID Auxiliary / Configuration Port System Data Preamble Postamble LRC Status Intercharacter Delay Response Timeout Chapter 4 Read Cycle Read Cycle by ESP Read Cycle Serial Commands Multisymbol MS-890 Industrial Automation Scanner User Manual iii

4 Table of Contents Trigger External Trigger State Serial Trigger Start Character (Non-Delimited) Stop Character (Non-Delimited) End of Read Cycle Good Decode Reads Gain Settings Focus Scan Speed Automatic Gain Control (AGC) Settings Maximum Element Tracking Adjustment Chapter 5 Symbologies Symbologies by ESP Symbologies Serial Commands Code Code 128 / EAN Interleaved 2 of Codabar UPC/EAN Code Pharmacode PDF Narrow Margins / Symbology ID Background Color Autodiscriminate Chapter 6 I/O Parameters I/O Parameters by ESP I/O Parameters Serial Commands Symbol Data Output No Read Message Bad Symbol Message No Symbol Message Read Duration Output Output Indicators Beeper Serial Verification EZ Button EZ Button Modes Input Configurable Output Trend Analysis Output Diagnostics Output iv MS-890 Industrial Automation Scanner User Manual

5 Introduction Configurable Output Trend Analysis Output Diagnostics Output Configurable Output Trend Analysis Output Diagnostics Output Database Identifier Output Quality Output Chapter 7 Matchcode Matchcode by ESP Matchcode Serial Commands Overview of Matchcode Using Master Symbols Matchcode Type Sequence Step New Master Pin Match Replace Mismatch Replace Chapter 8 Diagnostics Diagnostics by ESP Diagnostics Serial Commands Counts Hours Since Last Reset Warning Messages Laser Current Warning Present Operating Temperature (Deg. C) High Temperature Threshold Low Temperature Threshold Lifetime Hours Service Message Chapter 9 Calibration Calibration Serial Commands Calibration Steps Calibration Routine Calibration Results Configuration Database Optoelectric Control Advanced Calibration Features Calibration by Embedded Menu Chapter 10 Raster/Laser Raster/Laser Setup by ESP Raster/Laser Serial Commands Raster Setup Laser Framing MS-890 Industrial Automation Scanner User Manual v

6 Table of Contents Raster/Laser by Embedded Menu Chapter 11 Terminal Terminal Window Find Send Macros Terminal Window Menus Chapter 12 Utilities Serial Utility Commands Read Rate Counters Device Control Differences from Default Master Database Digital Bar Code Firmware Autodiscriminate Scanner Status Requests Chapter 13 Output Format Output Format Serial Commands Output Format Status Format Assign Format Extract Format Insert Output Filter Configuration Number of Filters Chapter 14 Wiring Box Wiring Box Description Installation Steps Wiring Box Ports Wiring Box PCB with Connectors Mounting Plate Appendices Appendix A General Specifications...A-2 Appendix B Electrical Specifications...A-4 Appendix C Serial Configuration Commands...A-9 Appendix D ASCII Table...A-15 Appendix E Embedded Menus...A-17 Appendix F Defaulting / Saving / Initializing...A-18 Appendix G Position Scanner and Symbol...A-21 Appendix H Object Detector...A-22 Appendix I Bar Code Configuration...A-23 Appendix J Test Read Rate...A-25 Appendix K Formulas for Number of Decodes...A-27 vi MS-890 Industrial Automation Scanner User Manual

7 Introduction Appendix L Operational Tips...A-32 Appendix M Interface Standards...A-33 Appendix N Multidrop Communications...A-34 Appendix O Glossary of Terms...A-39 MS-890 Industrial Automation Scanner User Manual vii

8 About the MS-890 Industrial Automation Scanner About the MS-890 Industrial Automation Scanner The key features of the MS-890 Industrial Automation Scanner are: Wide angle sweeping raster Long-distance read range (10 to 120 (254 mm to 3,048 mm) EZ Button setup Configurable with ESP Software 400 to 1,000 decodes per second IP65 rated enclosure Optional wiring box LED performance indicators About This Manual This manual provides complete information on setting up, installing, and configuring the MS-890 Industrial Automation Scanner. The chapters follow the ESP menus, which are presented in the order in which a scanner might be set up and made ready for industrial operation. Host serial commands are presented side-by-side with ESP. Highlighting Serial commands, highlighted command fields, and default command settings are highlighted in rust bold. Cross-references and web links are highlighted in blue bold. References to ESP, its toolbar headings (Communications, Read Cycle, Symbologies, etc.), menu topics, and other points of emphasis, are highlighted in Bold Initial Caps. Host Communications There are four ways to configure and test the MS-890 Industrial Automation Scanner: EZ Button. Microscan s Windows-based ESP (Easy Setup Program), which offers point-and-click ease of use and visual responses to user adjustments. Serial commands, such as <K100,1>, that can be sent from ESP s Terminal or another terminal program, or encoded in Code 128 symbols. The tree controls and graphic interfaces in ESP s App Mode. viii MS-890 Industrial Automation Scanner User Manual

9 Statement of Agency Compliance Introduction The MS-890 Industrial Automation Scanner has been tested for compliance with FCC (Federal Communications Commission) regulations and has been found to conform to all applicable FCC Rules and Regulations. To comply with FCC RF exposure compliance requirements, this device must not be co-located or operate in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. The MS-890 Industrial Automation Scanner has been tested for compliance with CE (Conformité Européenne) standards and guidelines, and has been found to conform to applicable CE standards, specifically EN :2001: for Class A products; EN : 2000+A2:2005; EN :1995+A1:2001; EN : Immunity. The MS-890 Industrial Automation Scanner has been tested by an independent electromagnetic compatibility laboratory in accordance with the applicable specifications and instructions. Approvals This equipment is in compliance or approved by the following organizations: FCC (Federal Communications Commission) CDRH (Center for Devices and Radiological Health) CE (Conformité Européenne) UL/cUL (Underwriters Laboratories, Inc.; UL Canada) BSMI (Bureau of Standards, Metrology and Inspection) MS-890 Industrial Automation Scanner User Manual ix

10 Warning and Caution Summary Warning and Caution Summary This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. European models must use a similarly rated Class I or Class II power supply that is certified to comply with standard for safety EN Use of controls, adjustments, or performance of procedures other than those specified herein may result in hazardous laser light radiation exposure. There are no user serviceable parts in the scanner. Opening the scanner voids the Microscan Systems warranty and could expose the user to laser diode power of up to 7mW. The laser beam can be harmful to eyesight. Avoid eye contact with the laser beam. Never point the beam at other people, or in a direction where people may be passing. x MS-890 Industrial Automation Scanner User Manual

11 Statement of RoHS Compliance Introduction All Microscan readers with a G suffix in the FIS number are RoHS-Compliant. All compliant readers were converted prior to March 1, All standard accessories in the Microscan Product Pricing Catalog are RoHS-Compliant except and These products meet all the requirements of Directive 2002/95/EC European Parliament and the Council of the European Union for RoHS compliance. In accordance with the latest requirements, our RoHS-Compliant products and packaging do not contain intentionally added Deca-BDE, Perfluorooctanes (PFOS) or Perfluorooctanic Acid (PFOA) compounds above the maximum trace levels. To view the document stating these requirements, please visit: and Please contact your sales manager for a complete list of Microscan s RoHS-Compliant products. This declaration is based upon information obtained from sources which Microscan believes to be reliable, and from random sample testing; however, the information is provided without any representation of warranty, expressed or implied, regarding accuracy or correctness. Microscan does not specifically run any analysis on our raw materials or end product to measure for these substances. The information provided in this certification notice is correct to the best of Microscan s knowledge at the date of publication. This notice is not to be considered a warranty or quality specification. Users are responsible for determining the applicability of any RoHS legislation or regulations based on their individual use of the product. In regards to RoHS Directive 2011_65_EU Microscan produces Monitoring and Control Instruments as well as Industrial Monitoring & Control Instruments as defined within the directive. Microscan has developed and is implementing a RoHS2 compliance plan with the intention of bringing all active products listed in our current marketing literature within full compliance as per the directive deadlines. Key milestones for the transition plan are as follows: Complete internal product audit by July Initial Monitoring and Control Instruments RoHS2 compliant products available by December 2014 Initial Industrial Monitoring & Control Instruments RoHS2 compliant products available by July 2015 All new products introduced in 2015 are expected to be WEEE & RoHS2 compliant. Microscan will mark the products with the CE marking that complies with the RoHS2 process to acquire CE certification per the example given: Example >> Machinery directive + EMC directive + RoHS2 = Declaration of Conformity. MS-890 Industrial Automation Scanner User Manual xi

12 Statement of RoHS Compliance xii MS-890 Industrial Automation Scanner User Manual

13 1 Quick Start Contents Step 1 Check Required Hardware Step 2 Connect the System Step 3 Position Scanner and Symbol Step 4 Install ESP Step 5 Select Model Step 6 Autoconnect Step 7 Receive Settings Step 8 Calibrate Step 9 Test Read Rate Step 10 Configure the Scanner in ESP Step 11 Save Configuration in ESP This chapter is designed to get your MS-890 up and running quickly, using the EZ Button or ESP (Easy Setup Program). Following these steps will allow you to get a sense of the scanner s capabilities and to test symbol decode performance. Detailed setup information for installing the scanner into your application can be found in the subsequent chapters. Important: If you are switching from an MS-880 to an MS-890 in your application, follow these steps when you open ESP: 1. With your MS-890 connected to the host computer, open your most recent MS-880.esp file. 2. Connect to the MS-890 and send all settings. 3. Click the Switch Model button at the top of the ESP view. When you see the model menu, select the MS Receive settings. Note: After receiving settings, you can delete the previous MS-880 model by opening the Model dropdown menu from the menu toolbar, selecting Remove Model, and selecting MS-880. MS-890 Industrial Automation Scanner User Manual 1-1

14 Check Required Hardware Step 1 Check Required Hardware Hardware Required Caution: Be sure that all cables are connected BEFORE applying power to the system. Always power down BEFORE disconnecting any cables. Item Description Part Number 1 MS-890 Industrial Automation Scanner FIS G, -0002G 2 9-Pin Configuration Cable Power Supply Object Detector (optional) Comm./Serial Cable Note: Standalone configuration shown above. 1-2 MS-890 Industrial Automation Scanner User Manual

15 Step 2 Connect the System Quick Start Standalone With Wiring Box Caution: Be sure that all cables are connected BEFORE applying power to the system. Always power down BEFORE disconnecting any cables. Connecting the MS-890 Standalone 1. Attach the configuration cable to either the 9-pin (preferred) or 25-pin connector (on bottom of unit) to configure, test, and default the scanner. 2 Receive 3 Transmit 5 Signal ground 9-pin host configuration connector 2. Attach the power supply cable to the 3-pin power connector on the bottom of the scanner. Chassis ground 2 Power ground 1 1 Power Ground pin host connector 18 Power Power +10 to 28 VDC (in) Power connector 2 1 Trigger connector MS-890 Industrial Automation Scanner User Manual 1-3

16 Connect the System Connecting the MS-890 with Wiring Box 1. Be sure that the wiring box power cord is not plugged in. 2. Connect the scanner to the host computer. 3. Use the 9-pin configuration connector shown below to connect with your computer. This port is useful for setting up, testing, and defaulting the scanner. 2 Receive 3 Transmit 5 Signal ground 9-pin host configuration connector 4. Connect power to the wiring box. 5. Apply power to the wiring box and confirm that the LED next to the right side power terminal is green and not red. 6. Disconnect power. 7. Plug the ribbon cable (provided with wiring box) into the bottom of the scanner. 8. Attach the scanner to the wiring box with the 4 screws provided. 9. Power-on the scanner. 1-4 MS-890 Industrial Automation Scanner User Manual

17 Step 3 Position Scanner and Symbol Set up a symbol at the distance that will be used in your application. Quick Start Centerline of of scan window Scan range starts here Scan Range Starts Here Note: Code 39 is the default symbology enabled. If you are uncertain as to the symbology type in your application, enable all symbologies by clicking the Autodiscriminate button in EZ Mode. Important: If using Interleaved 2 of 5 symbols in your application, verify that the number of characters in the symbols being scanned matches the symbol length enabled for the Interleaved 2 of 5 symbology (default is 10 and 6). MS-890 Industrial Automation Scanner User Manual 1-5

18 Install ESP Step 4 Install ESP Easy Setup Program (ESP) is Microscan s proprietary setup and testing application. The purpose of ESP is to provide a quick and easy way to set up and configure Microscan products. When the MS-890 is connected to a host computer (Windows Vista, XP, or 2000), ESP can be used to set up communication with a host, configure various firmware settings, and control verification processes. Important: To migrate MS-880 settings to MS-890 settings in ESP, refer to the beginning of Chapter 2, Using ESP. If installing from the Microscan Tools Drive: 1. Insert the Microscan Tools Drive into a USB port on your computer. 2. Choose ESP Software from the main menu. 3. Select the Current Version of ESP and follow the file download prompts. If downloading from the Microscan website: 1. Go to 2. Create a new mymicroscan member account or, if you are already a member, enter your user name and password. 3. Click the Download Software link and extract the latest version of ESP to a directory of your choice. Note where your ESP.exe file is stored on your hard drive. 4. At the end of the installation process, the following icon will appear on your desktop: 5. Click the ESP icon to start the program. System Requirements for ESP 233 MHz Pentium PC Windows 8, 7, Vista, or XP operating system (32-bit or 64-bit) Internet Explorer 5.0 or higher 128 MB RAM or greater; 160 MB free disk space 800 x color display (1024 x bit color recommended) 1-6 MS-890 Industrial Automation Scanner User Manual

19 Step 5 Select Model When you start ESP, this menu will appear: Quick Start 1. Select the MS-890 from the menu and click OK. If you do not want to make this selection every time you start ESP, uncheck Show this dialog at startup. 2. Click Yes when the following dialog appears: Note: If you need to select another model later, click the Switch Model button near the top of the screen. MS-890 Industrial Automation Scanner User Manual 1-7

20 Autoconnect Step 6 Autoconnect 1. Select the appropriate port and click Start when the following dialog appears. Note: If your communications port is not the default COM1, use the dropdown menu to change your port. Once you have chosen the correct port, click Start to connect. When you are connected, you will see the green connection indicator in the status bar at the bottom right of your screen: 2. If the connection attempt fails, click the Autoconnect button, select a different communications port, and try again. Note: If your RS-232 host settings cannot be changed to match the scanner s settings, select Connect... from the Connect menu in the menu toolbar, and then click the Force Connect box when you see the dialog shown at left. 1-8 MS-890 Industrial Automation Scanner User Manual

21 Step 7 Receive Settings Quick Start To copy the scanner s memory settings into ESP, right-click in the configuration window and select Receive Reader Settings from the dropdown menu. Receive Reader Settings When you select Receive Reader Settings, the settings from the scanner s memory are sent to ESP. MS-890 Industrial Automation Scanner User Manual 1-9

22 Calibrate Step 8 Calibrate 1. Click the Calibration button in EZ Mode or in the Calibration view. 2. Allow some time for the scanner to cycle through the focus, gain, and tracking settings. Do not move or disturb the scanner or test symbol while calibration is in progress. 3. When calibration is complete, the settings that provided the highest read rate will be selected. You will see one of the following messages: Calibration Passed, Calibration Failed, or Original Settings Were Optimal. Note: To silence the beeper, interrupt scanning by removing or blocking the test symbol, or send a <K702,0> command to disable the beeper. If calibration fails, try the following: 1. Check the read range for your particular symbol density. 2. Examine symbol quality and try a different sample symbol. 3. Slightly skew or tilt the symbol or scanner to minimize specular reflection. 4. Verify that the correct symbology is enabled MS-890 Industrial Automation Scanner User Manual

23 Step 9 Test Read Rate Quick Start Important: To receive symbol data through the 9-pin configuration port, you must enable the port with the following command: <K146,,1>. 1. Position the symbol in front of an operational MS-890 scanner. 2. Click the Utilities button. 3. Click the Start button in the Read Rate view. If calibration has passed, the scanner sends data to the host computer and emits a beep (if the beeper is enabled) for each good read. Move your symbol toward the scanner and away from the scanner until the decode rates drop off in each direction. This will give you a sense of the depth of field (inner and outer ranges) for your symbol s density and range. Depth of field Note: If the scanner is in the default Continuous Read mode and not in read rate or calibration routine, it will read and beep repeatedly as long as a readable symbol remains in the read range and the read cycle configuration has not changed. To end the read rate test, right click Read Rate and select the Stop button. MS-890 Industrial Automation Scanner User Manual 1-11

24 Configure the Scanner in ESP Step 10 Configure the Scanner in ESP To make setup changes to the MS-890, click the App Mode button. The following modes are accessible by clicking the buttons in the first row of App Mode icons: Test and Calibrate the scanner in EZ Mode. Establish communications between ESP and the scanner by clicking the Autoconnect button. Send or receive commands by clicking the Send/Recv button. Switch reader models by clicking the Switch Model button. Click the Parameters button to make changes to tree control settings. Click the Setup button to adjust and test scanner settings in Calibration, Raster Setup, Laser Framing, Configuration Database, Ordered Output, and Output Format. Access the Terminal, where you can view symbol data and enter serial commands. Review status settings or make changes to operational commands in Utilities MS-890 Industrial Automation Scanner User Manual

25 Step 11 Save Configuration in ESP To make changes to a configuration setting: 1. Left click on the + to expand the desired tree. 2. Double click on the desired parameter and click once in the selection box to view options. 3. Place your cursor in the selection box, scroll down to the setting you want to change, and click once on the setting. Quick Start 4. Left click again on the open screen to complete your selection. 5. Right click on the open screen and select Save to Reader to implement the command in the scanner. Saving Options Send, No Save. Changes will be lost when power is re-applied to the scanner. Send and Save. This activates all changes in current memory and saves to the scanner for power-on. MS-890 Industrial Automation Scanner User Manual 1-13

26 Save Configuration in ESP 1-14 MS-890 Industrial Automation Scanner User Manual

27 2 Using ESP Contents EZ Mode Application Mode Menu Toolbar Autoconnect View Navigating in ESP Send/Receive Options This section is designed to help you understand the basic structure and elements of ESP (Easy Setup Program). When you open ESP, unless otherwise specified in the ESP Preferences dialog accessible from the Options heading on the menu toolbar, you will enter EZ Mode for initial setup. From there, you can enter Application Mode (App Mode) and access several configuration menus (Communications, Read Cycle, Symbologies, I/O Parameters, Symbol Quality, Matchcode, and Diagnostics), a Camera setup interface, a Terminal interface, a Utilities interface, and an Output Format interface. For ESP system requirements, see System Requirements for ESP in Chapter 1, Quick Start. Important: If you are switching from an MS-880 to an MS-890 in your application, follow these steps when you open ESP: With your MS-890 connected to the host computer, open your most recent MS-880.esp file. Connect to the MS-890 and send all settings. Click the Switch Model button at the top of the ESP view. When you see the model menu, select the MS-890. Receive settings. Note: After receiving settings, you can delete the previous MS-880 model by opening the Model dropdown menu from the menu toolbar, selecting Remove Model, and selecting MS-880. MS-890 Industrial Automation Scanner User Manual 2-1

28 EZ Mode EZ Mode In EZ Mode you are presented with the Locate, Calibrate, and Test options. After connecting to your scanner, EZ Mode is the screen you will see. You will be provided with on-screen instructions that will help you with positioning, testing, and calibration. Test Click the Test button to start the Read Rate test for a quick indication of the scanner s read capabilities and the limits of your application. When Decodes per Second is unchecked, the test will count the percentage of decodes relative to the number of actual scans. Click Stop to end the test. Calibrate The calibration routine that will optimize the scanner by comparing Read Rates at various camera and image processing settings. Starts Read Rate test. Click Calibrate to begin the initial calibration routine. Calbration is explained at the left of the EZ Mode screen, and also in Quick Start. Enter App Mode to access configuration trees and other setup features. Allows you to decode a variety of symbologies without stopping your application to reconfigure symbology settings. Saves Calibration settings. Ends Read Rate test. 2-2 MS-890 Industrial Automation Scanner User Manual

29 Application Mode Using ESP From EZ Mode, you can click on the App Mode button to access specific configuration menus, Utilities tools, Camera setup, Output Format options, and a Terminal window where serial commands can be entered. Note: The App Mode and EZ Mode buttons appear in the same position to allow easy switching between these primary modes. Click this icon to return to EZ Mode. Menu toolbar. Calibration, Raster/Laser, Terminal, Utilities. Click here for Ordered Output and Output Format features. Click on icons in this row to access configuration trees like the one shown here. Click the Configuration button to return to full App Mode view from Calibration, Raster/Laser, Terminal, Utilities, or Output Format. Note: For specific information on any of the icons shown above in the operations bar or configuration bar, see the corresponding sections of this manual. MS-890 Industrial Automation Scanner User Manual 2-3

30 Menu Toolbar Menu Toolbar File > New Whenever New is selected, the default configuration of ESP is loaded. Open/Save When Save or Save As is selected, the ESP configuration is saved to the host computer s hard drive and available whenever the same file is selected under Open. Important: When you save menu changes to your hard drive, these changes are not saved to your scanner. The illustration below shows how settings can be saved and received between ESP and the scanner, and ESP and the host hard drive. (Save to Scanner) (Receive Scanner Settings) Import/Export Import converts the ASCII settings from a text file to ESP configuration settings. Export converts the active ESP configuration settings to an ASCII text file. 2-4 MS-890 Industrial Automation Scanner User Manual

31 Model In Model you can select any of the models shown in ESP s model menu. When you choose another model, your current connection to your present model will be terminated. To connect to another model, select New Model, choose a new model from the menu, and click OK. Using ESP Note: All the models you have enabled by selecting will continue to appear in the Model menu and that the same menu is repeated when clicking the Switch Model icon. When you save your ESP file, you will be saving the settings of all the models defined in a single ESP file. MS-890 Industrial Automation Scanner User Manual 2-5

32 Menu Toolbar Options The Options menu allows you to save memos and set up ESP Preferences. Note: Preferences will be saved and loaded into ESP whenever ESP is opened next, whether or not you save the ESP file. Preferences > General Tab The Toolbar Style options allow you to determine how ESP will display the mode options in the two rows at the top of the screen. Reload Last File At startup, reloads the last file saved to the host computer s hard drive. Show Model Prompt At startup, shows the model menu displaying all supported readers. Show Connect Prompt At startup, displays the Would you like to connect to the MS-890? prompt. Receive After Connect At startup, loads the scanner s settings into ESP. (This is not recommended if you want to preserve your ESP settings for future use.) Skip EZ Mode At startup, skips EZ Mode and opens directly in App Mode. 2-6 MS-890 Industrial Automation Scanner User Manual

33 Preferences > Terminal Tab Using ESP Show Non-Printable Characters When Show Non-Printable Characters is enabled, characters such as CRLF will be displayed in the Terminal window. When Enhanced Format is checked, the characters are displayed with more detailed formatting. Change Keyboard Macros Clicking the Change Keyboard Macros button brings up the Function Keys dialog. In this dialog you can select the desired function key and then enter your macro keystrokes in the associated key map. For example, to make Ctrl-F2 the keystroke to send a trigger character, select F2, then in the Ctrl row, enter <trigger character> and click OK. Then whenever the Ctrl-F2 keystroke is pressed, the trigger character will start the read cycle. Note: The F1 key is reserved for opening ESP Help and the F3 key is reserved for the Find Next function. Change Font Allows you to modify the font used for decode data received from the scanner on the Terminal screen. Change Echo Font Allows you to modify the font used for command characters typed into the Terminal view. Enable Echo Allows you to enter command characters in Terminal. Display Incoming Data Even When Not in Focus When Display Incoming Data Even When Not in Focus is enabled, data from the scanner will continue to appear in the terminal even when ESP is not the top window. MS-890 Industrial Automation Scanner User Manual 2-7

34 Menu Toolbar Preferences > Bar Code Options Tab The Bar Code Options dialog allows you to set the size of user-created symbols. Sizing Information Sets the bar width or module width (in mils, or thousandths of an inch) of user-created symbols. Example: A bar width of 13 is inches. Caption Allows you to choose the font of human-readable captions (if symbol captions are required), and to determine the orientation of captions in relation to symbols. Note: Symbols can be created using the Bar Code Dialog. 2-8 MS-890 Industrial Automation Scanner User Manual

35 Preferences > Advanced Tab Using ESP The Auto Sync options at the top of the Advanced tab allow you to determine whether Auto Sync will be enabled automatically in sections of ESP where it is used, or if it will ask you before it enables Auto Sync functions. Always Ask Before Auto Sync Occurs If you check this option box, you are then able to determine what specific Auto Sync functions will be enabled. Receive Settings from the Reader will automatically send the scanner s settings to ESP when Auto Sync is enabled. Send ESP Settings to the Reader will automatically send all scanner configuration settings chosen in ESP to the scanner. Do Not Send or Receive Settings creates a condition in which Auto Sync will not automatically send scanner settings to ESP, or send ESP settings to the scanner. Send XON with Autoconnect Sends an XON (Begin Transmission) command to the scanner before starting the Autoconnect routine. Ask to Save ESP File when Quitting When enabled, prompts the user to save a.esp file when ending a session. The.esp file will be saved in the location of your choice. MS-890 Industrial Automation Scanner User Manual 2-9

36 Menu Toolbar Preferences > Advanced Tab (cont.) Show TCP/IP Connection Option When enabled, shows a TCP/IP option on the Select Protocol dialog. Note: This option should only be selected if you intend to connect using an Ethernet adapter. Use Default Storage Location When enabled, automatically stores data in ESP s Application Data folder MS-890 Industrial Automation Scanner User Manual

37 Using ESP Document Memo The information you type in the Document Memo field will appear in a context-sensitive text box whenever your cursor hovers over the Document Memo item on the Options menu. Model Memo Similar to Document Memo, the information you type in the Model Memo field will appear in a context-sensitive text box whenever your cursor hovers over the Model Memo item on the Options menu. Memos created in Model Memo are specific to the model enabled when the message was created. Note: Memos must be saved in a.esp file if you want them to available in your next session. If you do not save your current session, any memos that you have entered during the session will be discarded, and will be unavailable in your next session. MS-890 Industrial Automation Scanner User Manual 2-11

38 Autoconnect Autoconnect You can use Autoconnect to establish a connection between the scanner and the host. If your communications port is not the default COM1, use the dropdown menu to change ports. Once you have chosen the correct port, click Start to connect. When you are connected, you will see the green connection indicator in the status bar at the bottom right of your screen: 2-12 MS-890 Industrial Automation Scanner User Manual

39 Autoconnect (cont.) If your RS-232 host settings cannot be changed to match the scanner s settings: Click Connect on ESP s menu toolbar, and then select Connection Wizard. When the Select Protocol dialog appears, select RS-232 and click Next. Using ESP When the RS-232 dialog appears, check the Force Connect box and click the Connect button. MS-890 Industrial Automation Scanner User Manual 2-13

40 View View The View menu allows you to move quickly between interfaces without using the icon buttons on the App Mode toolbar. It also allows you to access the Bar Code Dialog. Bar Code Dialog In the Bar Code Dialog you can create symbols by typing the text you wish to encode. This is a useful tool for creating configuration symbols, allowing you to configure your scanner by reading the symbols you create. Choose a spatial orientation for the new symbol. Drag configuration commands from the tree controls directly into this field to encode new symbols. Create a caption for the symbol that matches the encoded data, or write your own caption. The symbols you create will be displayed in the field at the bottom of the Bar Code Dialog. Click the Differences from Default Settings button to create a symbol encoded with configuration settings that differ from ESP defaults. Differences from Default can be viewed on the Differences tab in the Utilities view. Click Add start configuration code and Add end configuration code; Save Settings to add a symbol that will enable Bar Code Configuration mode and a symbol that will save all new configuration settings. (Both symbols shown at left). See Bar Code Configuration on page A-23 for more information about configuring the MS-890 by decoding symbols MS-890 Industrial Automation Scanner User Manual

41 Navigating in ESP Using ESP To change scanner settings, or to access the Calibration, Raster/Laser, Terminal, Utilities, or Output Format views, click the App Mode button. To return to EZ Mode, click the EZ Mode button. To make changes to configuration settings in the tree controls: 1. Left-click on the + to expand menu items. 2. Double-click the desired parameter and single-click in the selection box to view options. 3. Place your cursor in the selection box, scroll down to the setting you want to change, and single-click the setting. The X denotes the default option setting. 4. Left-click again on the open screen to complete the selection. 5. Right-click on the open screen and select Save to Reader to implement the command in the scanner. You can send the command without saving it, or you can send and save the command simultaneously. MS-890 Industrial Automation Scanner User Manual 2-15

42 Send/Receive Options Send/Receive Options To access Receive, Save, and Default options, click the Send/Recv button. You can also access these options by right-clicking in any of the configuration views. Receiving From the Send/Recv menu, select Receive Reader Settings. Caution: Do not select this option if you do not want to upload the scanner s settings. For example, if your ESP file has a number of custom settings that you want to maintain and download into the scanner, these settings would be lost by choosing Yes. This is useful if you want to receive (upload) the scanner s settings and save them as a file for future use. For example, if your scanner has settings that you do not want to change, choosing Yes would allow you to load those settings to ESP and save them in an ESP file for later retrieval. Receiving the scanner s settings will also assure that you will not be subsequently saving any unwanted changes that you or someone else has made previously in ESP. Saving Send, No Save (<A>) Saves ESP settings to current memory. Send and Save (<Z>) Activates all changes in current memory and saves to the scanner for power-on MS-890 Industrial Automation Scanner User Manual

43 Using ESP Defaulting When you select Default Current Menu Settings or Default all ESP Settings, you are only defaulting the ESP settings. Advanced Options Send Current View This is the same as Save to Reader > Send No Save except that only the commands in the current configuration tree are sent. Send Current Command This is the same as Send Current View, except that it saves only the command that is currently selected. Add / Remove Exception After you perform a Receive Reader Settings command 1 and you click on the Add Exception option, you may see a list of serial commands. These are commands that may be in your scanner s firmware, but not included in, or different from, your current version of ESP. You can edit these commands by double-clicking on them and changing them as needed. It is important to note that these commands will be saved to your scanner whenever you send a Save to Reader command, or an <A> or a <Z> command. Also, if there is a corresponding ESP menu item, the ESP Value column for that item will be blank following a Receive Reader Settings command. 1. From the Send/Recv button or by right-clicking in any blank section of a tree control view. MS-890 Industrial Automation Scanner User Manual 2-17

44 Send/Receive Options 2-18 MS-890 Industrial Automation Scanner User Manual

45 3 Communications Contents Communications by ESP Communications Serial Commands RS-232/422 Host Port Host Port Parameters Host Protocol Poll Address ACK / NAK Options Polling Mode Options Auxiliary Port Protocol Daisy Chain Autoconfigure Daisy Chain Scanner ID Auxiliary/Configuration Port System Data Preamble Postamble LRC Status Intercharacter Delay Response Timeout With Microscan s ESP (Easy Setup Program), configuration changes can be made in the ESP menus, then sent and saved to your scanner. The user can also send serial commands to the scanner via the ESP s Terminal window. This section includes connecting parameters and options for communicating by the auxiliary port and various interfaces. Note: When assigning characters in user-defined fields, the characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. Note: Default settings for establishing communications are: Baud = 9600 Parity = Even Stop Bits = One Data Bits = Seven Flow Control = None MS-890 Industrial Automation Scanner User Manual 3-1

46 Communications by ESP Communications by ESP Click this button to bring up the Applications menu. Click this button to bring up the Communication menu. Communications Serial Commands Command Title Host Port Parameters Aux Port Protocol To open nested options, single-click the +. Host Protocol Preamble Postamble Response Timeout Intercharacter Delay LRC Auxiliary/Configuration Port System Data ACK/NAK Options Polling Mode Options Daisy Chain Autoconfigure Daisy Chain Scanner ID To change a setting, double-click the setting and use your cursor to scroll through the options. Command Format <K100,baud,parity,stop bits,data bits> <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status,daisy chain ID> <K140,protocol,address> <K141,status,preamble character(s)> <K142,status,postamble character(s)> <K143,timeout setting> <K144,time interval> <K145,status> <K146,aux port status,config port status> <K147,RES,REQ,STX,ETX,ACK,NAK> <K148,RES,REQ,STX,ETX,ACK,NAK> <K150DAISY> <K151,daisy chain scanner,daisy chain scanner ID> 3-2 MS-890 Industrial Automation Scanner User Manual

47 RS-232/422 Host Port Includes host port connections and host protocols. Communications Communications Options You can communicate with the scanner through the following ports: 9-pin D-sub external connector Wiring box 25-pin D-sub external connector Only one port can be used at a time to receive commands. Communications with Host through the 9-pin Host Port For the 9-pin configuration port, set the host communications settings as follows: 57.6K baud, 8 data bits, 1 stop bits, and None parity. See Chapter 1, Quick Start, for more information on using the 9-pin port. Note: The 9-pin configuration port settings are not changeable. Communications with Host through the 25-pin Port The default 25-pin host port configuration settings are as follows: 9600, 7, 1, and Even. Making changes to these communications parameters without corresponding changes in linked device(s) can result in the loss of menu access. If this should occur, connect via the 9-pin port and reset your scanner s host parameters to match the 25-pin defaults. Communications with Host through the Wiring Box The settings are the same as those of the 25-pin port. See Chapter 14, Wiring Box, for details on wiring connections. MS-890 Industrial Automation Scanner User Manual 3-3

48 Host Port Parameters Host Port Parameters Important: This applies only to the 25-pin port and wiring box connections (not for 9-pin port). Note: See Communications with Host through the 9-pin Host Port on page 3-3 for 9-pin host port parameters. Baud Rate (Host Port) Usage: Definition: Can be used to transfer data faster or to match host port settings. The rate at which the scanner and host transfer data back and forth. Serial Cmd: <K100,baud rate,parity,stop bits,data bits> Default: 9600 Options: 0 = = = = = = 19.2K 6 = 38.4K 7 = 57.6K 8 = 115.2K Parity (Host Port) Usage: Only changed if necessary to match host setting. Definition: An error detection routine in which one data bit in each character is set to 1 or 0 so that the total number of 1 bits in the data field is even or odd. Serial Cmd: <K100,baud rate,parity,stop bits,data bits> Default: Even Options: 0 = None 1 = Even 2 = Odd Stop Bits (Host Port) Usage: Only changed if necessary to match host setting. Definition: One or two bits added to the end of each character to indicate the end of the character. Serial Cmd: <K100,baud rate,parity,stop bits,data bits> Default: One Options: 0 = One 1 = Two Data Bits (Host Port) Usage: Only changed if necessary to match host setting. Definition: Number of bits in each character. Serial Cmd: <K100,baud rate,parity,stop bits,data bits> Default: Seven Options: 0 = Seven 1 = Eight 3-4 MS-890 Industrial Automation Scanner User Manual

49 Host Protocol Communications Usage: In general, point-to-point protocols work well in most applications. They require no address and must use RS-232 or RS-422 communications standards. Definition: Protocols define the sequence and format in which information is transferred between the scanner and the host, or in the case of Polling Mode, between scanners and a concentrator. Important: When using Polling Mode, LRC must be Enabled and Preamble/ Postamble must be Disabled. Serial Cmd: <K140,protocol,address> Default: Point-to-Point Options: 0 = Point-to-Point 1 = Point-to-Point with RTS/CTS 2 = Point-to-Point with XON/XOFF 3 = Point-to-Point with RTS/CTS and XON/XOFF 4 = ACK/NAK 5 = Polling Mode Point-to-Point (Standard) Usage: Used only with RS-232 or RS-422. Definition: Standard Point-to-Point requires no address and sends data to the host whenever it is available, without any request or handshake from the host. Serial Cmd: <K140,0> Point-to-Point with RTS/CTS Usage: A scanner initiates a data transfer with an RTS (request-to-send) transmission. The host, when ready, responds with a CTS (clear-to-send) and the data is transmitted. CTS and RTS signals are transmitted over two dedicated wires as defined in the RS-232 standard. Used only with RS-232. Definition: Point-to-Point with RTS/CTS (request-to-send/clear-to-send) is a simple hardware handshaking protocol that allows a scanner to initiate data transfers to the host. Serial Cmd: <K140,1> MS-890 Industrial Automation Scanner User Manual 3-5

50 Host Protocol Point-to-Point with XON/XOFF Usage: If an XOFF has been received from the host, data will not be sent to the host until the host sends an XON. During the XOFF phase, the host is free to carry on other tasks and accept data from other devices. Used only with RS-232. Definition: This option enables the host to send the XON and XOFF command as a single byte transmission command of start (^Q) or stop (^S). Serial Cmd: <K140,2> Point-to-Point with RTS/CTS and XON/XOFF Usage: Used only with RS-232. Definition: This option is a combination of Point-to-Point with RTS/CTS and Point-to-Point with XON/XOFF. Serial Cmd: <K140,3> ACK/NAK Definition: See the ACK / NAK Options command <K147> on page 3-8. Serial Cmd: <K140,4> Polling Mode Definition: See the Polling Mode Options command <K148> on page 3-9. Serial Cmd: <K140,5> 3-6 MS-890 Industrial Automation Scanner User Manual

51 Poll Address Communications Serial Cmd: <K140,protocol,address> Default: 1 Options: 1 to 50 1 = Poll address 0x1C, Select address 0x1D 2 = Poll address 0x1E, Select address 0x1F = Poll address 0x7E, Select address 0x7F MS-890 Industrial Automation Scanner User Manual 3-7

52 ACK / NAK Options ACK / NAK Options Definition: Serial Cmd: These parameters take effect for ACK/NAK <K140,4> on the main RS-232 or RS-422 ports (not on the Auxiliary Port), and are completely independent of the Polling Mode Options <K148>. The scanner always follows the protocol in both directions (to and from the host). There is no option to disable it from either direction. <K147,RES,REQ,STX,ETX,ACK,NAK> RES-NAK Defaults RES: (Reset) REQ: (Request) STX: (Start of Text) ETX: (End of Text) ACK: (Acknowledge) NAK: (Negative Acknowledge) 0x00 (disabled) 0x00 (disabled) 0x00 (disabled) 0x00 (disabled) 0x06 0x15 The following are general outlines of the ACK/NAK protocol. Items that are framed by brackets ( [ ] ) can either be disabled or enabled. LRC does not include STX, but it does include preamble, postamble, and ETX. Symbol Data Output TX to host: [STX] [preamble] SYMBOL DATA [postamble] [ETX] [LRC] Response from host: ACK/NAK. Sent when LRC, ETX, postamble, or timeout (waiting for more data) are detected (if REQ is disabled) depending on what is enabled. Commands from Host to Scanner TX to Scanner: [STX] <command> [ETX] [LRC] Response from Scanner: ACK/NAK. Sent when LRC, ETX, or command-ending angle bracket > are received, depending on what is enabled. Command Response from Scanner to Host TX to host: [STX] [preamble] COMMAND RESPONSE DATA [postamble] [ETX] [LRC] Response from host: ACK/NAK. Sent when LRC, ETX, postamble, command-ending angle bracket >, or timeout (waiting for more data) are detected, depending on what is enabled. As with Polling Mode <K140,5>, the scanner can optionally perform the REQ and RES event sequences in ACK/NAK mode. If the sender does not receive an ACK or NAK, it will send REQ to request such a response (if enabled). When the sender receives an ACK, too many NAKs, or times out (if already enabled), it will send a RES (if enabled) to terminate the transaction. 3-8 MS-890 Industrial Automation Scanner User Manual

53 Polling Mode Options Communications Definition: Serial Cmd: These parameters only take effect for Polling Mode <K140,5> on the main RS-232 or RS-422 ports (not on the Auxiliary Port), and are completely independent of the ACK/NAK Options <K147>. The values of protocol characters can be changed, but the protocol events cannot be disabled. The polling mode address is configured in the <K140> command (see Poll Address on page 3-7). <K148,RES,REQ,STX,ETX,ACK,NAK> RES-NAK Defaults RES: (Reset) REQ: (Request) STX: (Start of Text) ETX: (End of Text) ACK: (Acknowledge) NAK: (Negative Acknowledge) 0x04 (disabled) 0x05 (disabled) 0x02 (disabled) 0x03 (disabled) 0x06 0x15 MS-890 Industrial Automation Scanner User Manual 3-9

54 Auxiliary Port Protocol Auxiliary Port Protocol Note: The Aux Port cannot be used when the host port is set to RS-422 or Multidrop. As with the host port parameters, the auxiliary terminal s settings (baud rate, parity, stop bits, and data bits) must be identical with those of the auxiliary device. Usage: Definition: These commands set the communication parameters with the auxiliary port which can be used to configure menus, send data to the host, display data transmissions originating from the host of the scanner, and relay data from other scanners set in tandem (Daisy-Chained). If the scanner s host port needs to be dedicated to the host, but configuration must be done on the fly, the auxiliary port can be set to accept configuration changes by Command Processing. An auxiliary port connects the scanner to a remote display or to other scanners that can display or transfer data. As with the host port parameters, the auxiliary terminal s settings (baud rate, parity, stop bits, and data bits) must be identical to those of the auxiliary device. Aux Port Mode Note: The Aux Port interacts only with the host port via the 25-pin port except when in Daisy Chain mode. When in Daisy Chain mode, the Aux Port will also interact with the configuration port (9-pin port) or the wiring box network ports. Definition: Determines the flow of data between the auxiliary port device(s), the scanner, and the host. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: Disabled Options: 0 = Disabled 1 = Transparent 2 = Half Duplex 3 = Full Duplex 4 = Daisy Chain 5 = Command Processing 3-10 MS-890 Industrial Automation Scanner User Manual

55 Transparent (Aux Port Mode) Communications Usage: Definition: Often used in conjunction with handheld scanners. Employs an auxiliary readout to detect mis-applied symbols. In Transparent mode data is passed between the auxiliary port and the host. The scanner buffers data from the auxiliary port and echoes the keyed data on the auxiliary port. Data Initiated from the Auxiliary Port Auxiliary port data is passed through to the host whenever a return key is pressed at the auxiliary port or symbol data is sent. Whenever Aux Port data is sent with symbol data, the Aux Port data will appear between the preamble and the symbol data. Auxiliary port data to the host is always sent with a preamble and a postamble. If the scanner is in a polled mode to the host, auxiliary port data will still pass through. <D> is the only command accepted by the scanner from the auxiliary port. All other commands will pass through to the host. Data Initiated from the Scanner Transmission to the auxiliary port occurs immediately upon a good read. Scan data to the auxiliary port does not include a preamble or a postamble. Communications with the auxiliary port is always in Point-to-Point protocol, even if the host is in a polled protocol mode. Data Initiated from the Host All host data is echoed to the auxiliary port in unpolled and polled mode. Host Host Host Scanner Scanner Aux. Port Aux. Port Aux. Port Scanner Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> 1 = Transparent MS-890 Industrial Automation Scanner User Manual 3-11

56 Auxiliary Port Protocol Half Duplex (Aux Port Mode) Usage: Definition: Used to display symbol data on an auxiliary screen close to the scanner. In Half Duplex mode all auxiliary port data and symbol data is sent directly to the host. Symbol data is displayed on the auxiliary port screen at the same time the data is sent to the host. Data Initiated from the Auxiliary Port Auxiliary port data to the host is ignored if the scanner is in a polled mode. Auxiliary port data or scanned data is sent to the host whenever it is received. Auxiliary port data is not echoed. Auxiliary port data to the host is always sent without a preamble or a postamble. <D> is the only command that is accepted by the scanner from the auxiliary port. All other commands are passed through to the host. Host Scanner Aux. Port Data Initiated from the Scanner Scan data is transmitted to the auxiliary port at the same time it is transmitted to the host. Data transmission conforms with all parameters specified in the configuration menu (e.g., Preamble, Postamble, End of Read Cycle). Host Aux. Port Data Initiated from the Host All host data is echoed to the auxiliary port in unpolled mode. Host Scanner Aux. Port Scanner Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> 2 = Half Duplex 3-12 MS-890 Industrial Automation Scanner User Manual

57 Full Duplex (Aux Port Mode) Communications Usage: Definition: Used when communication to and from the auxiliary port is required. In Full Duplex mode all auxiliary port data and symbol data is sent directly to the host. Symbol data is not displayed on the auxiliary port screen. Data Initiated from the Auxiliary Port Auxiliary port data to the host is ignored if the scanner is in a polled mode. Auxiliary port data or scanned data is sent to the host whenever it is received. Auxiliary port data is not echoed. Auxiliary port data to the host is always sent without a preamble or a postamble. <D> is the only command that is accepted by the scanner from the auxiliary port. All other commands are passed through to the host. Host Scanner Aux. Port Data Initiated from the Scanner Scan data is not sent to the auxiliary port. Host Aux. Port Scanner Data Initiated from the Host All host data is echoed to the auxiliary port in unpolled mode. Host Aux. Port Scanner Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> 3 = Full duplex MS-890 Industrial Automation Scanner User Manual 3-13

58 Auxiliary Port Protocol Daisy Chain (Aux Port Mode) Note: See also Daisy Chain Autoconfigure on page Usage: Used in applications where: A symbol might be scanned in both ladder and picket fence directions. A symbol may be present on multiple sides of a package. Symbols are presented at different depths. Definition: In a daisy chain application, scanners are connected in series or daisy chain and decoded data is relayed from one scanner to another on up to the host. A master scanner has its host port linked to the host computer and its auxiliary port linked to the host port of the first secondary scanner in the chain. Thereafter, each secondary s auxiliary port is linked to the host port of the secondary that is further from the host in the daisy chain. Each scanner in the daisy chain can be assigned an ID that accompanies any data that it sends. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> 4 = Daisy Chain Function: Before the master scanner times out, it checks its auxiliary port for data. It should be set to wait at least 20 ms for each secondary in the daisy chain. (See Read Cycle Timeout on page 4-16.) If no data is received within the read cycle timeout, the master sends a No Read message to the host. Otherwise the complete data is sent. If for example the master scanner is set to timeout in 120 ms, the first secondary scanner downstream might be set to 100 ms, the next to 80 ms, and so forth, thus assuring that at least 20 ms elapses between transmissions. a Daisy-chained scanners can send a series of symbols by enabling Multisymbol and a common multisymbol separator. If the master scanner does not receive the expected number of symbols, No Read messages are appended to the data string to make up the difference between the number of symbols enabled in Multisymbol and the number of symbols read. For example, a master and two secondary scanners have Number of Symbols set to 3 and Multisymbol Separator defined as %. If the master and the first secondary scanner do not find symbols, but the next secondary scanner registers a good read, the transmitted results would be: symbol data % No Read % No Read a. The above example is based on the best case. Other factors such as baud rate, dynamic focus timing, number of characters in a given symbol, and the number of secondaries in the daisy chain can affect timing and may need to be included in your calculations for complete accuracy MS-890 Industrial Automation Scanner User Manual

59 Daisy Chain (Aux Port Mode) (cont.) Communications Conditions: The conditions for a daisy chain application are as follows: 1. The master scanner s trigger must be Serial or External; the secondary scanners triggers are configured for Serial. 2. All scanners are enabled to Daisy Chain mode. 3. Each scanner s auxiliary port must be connected to the Host port of its secondary scanner. 4. Each secondary scanner in the daisy chain must be set to send its data no less than 20ms before its preceding scanner. 5. All but the master scanner must have Postamble enabled and set to CR (^M) only. 6. All but the master scanner must have their No Read messages disabled. 7. If Multisymbol is enabled, Multisymbol Separator characters must match in all scanners and Number of Symbols must be set to number large enough to include all the symbols it may itself read plus the number of symbols that it will be expected to relay to the host or the next scanner up the line. 8. Symbology ID enable/disable must be the same in all scanners. 9. All but the master scanner must have their diagnostic warning messages disabled. 10. Daisy Chain ID Status enable/disable and the number of characters in Daisy Chain ID must be the same in all scanners. MS-890 Industrial Automation Scanner User Manual 3-15

60 Auxiliary Port Protocol Command Processing (Aux Port Mode) Usage: Definition: Allows user to send configuration from the Host port or the Aux Port. When enabled, Command Processing allows commands to be entered via the Aux Port. The following rules apply: Symbol data, including the serial trigger if used, will be transmitted to the last port from which a command was sent. If a reset occurs, all data will be transmitted to the host port. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Options: 5 = Command Processing 3-16 MS-890 Industrial Automation Scanner User Manual

61 Baud Rate (Aux Port) Communications Usage: Definition: Can be used to transfer data faster or match an auxiliary device. The rate at which the scanner and host transfer data back and forth. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: 9600 Options: 1 = = = = = 19.2K 6 = 38.4K 7 = 57.6K 8 = 115.2K Parity (Aux Port) Usage: Definition: Only changed if necessary to match host setting. An error detection routine in which one data bit in each character is set to 1 or 0 so that the total number of 1 bits in the data field is even or odd. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: Even Options: 0 = None 1 = Even 2 = Odd Stop Bits (Aux Port) Usage: Definition: Only changed if necessary to match host setting. Allows the user to select the last one or two bits in each character to indicate the end of the character. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: One Options: 0 = One 1 = Two MS-890 Industrial Automation Scanner User Manual 3-17

62 Auxiliary Port Protocol Data Bits (Aux Port) Usage: Definition: Only changed if necessary to match host setting. Number of bits in each character. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: Seven Options: 0 = Seven 1 = Eight Daisy Chain ID Status (Aux Port) Note: Enable/disable and length must be the same in all scanners. Usage: Used in a daisy chain setup in cases where the host needs to know which scanner in a daisy chain setup sent the data. Definition: Each scanner in a daisy chain can be assigned a one or two character ID that will appear in front of decoded data and identify its source. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: Disabled Options: 0 = Disabled 1 = Enabled Daisy Chain ID (Aux Port) Note: All secondary scanners must be set to Serial for Daisy Chain to function. See Trigger on page 4-5. Usage: Used in a daisy chain setup in cases where the host needs to know which scanner sent the data. Definition: A one or two character prefix which identifies the particular daisy chain scanner from which the data is being sent. Serial Cmd: <K101,aux port mode,baud rate,parity,stop bits,data bits,daisy chain ID status, daisy chain ID> Default: 1/ Options: Any one or two ASCII characters MS-890 Industrial Automation Scanner User Manual

63 Daisy Chain Autoconfigure Note: This command is not available in ESP. Usage: For quick setup and configuration of the daisy chain network. Communications Definition: Daisy Chain Autoconfigure is issued to the master scanner in the daisy chain and the software responds as follows: Counts the number of secondary scanners in the daisy chain. Assigns an internal ID number (1...n) to each secondary scanner, where the first secondary scanner is number 1 (and its own ID being a 0). Propagates the communications settings and the relevant operating modes of the master scanner to the host and auxiliary ports of each secondary scanner. Resets each secondary scanner. Verifies that each secondary scanner has acquired the new settings. Serial Cmd: <K150DAISY> When setting up a daisy chain operation, follow these steps: 1. Set the master (the scanner connected to the host) scanner to Serial. This sets all the scanners in the daisy chain to Serial when the command is carried out. Before Autoconfigure you must set the primary scanner to Serial (S): Host Primary Scanner Secondary Scanner S S S Secondary Scanner 2. Send <K150DAISY> command. 3. If necessary, set the master scanner to Edge. After Autoconfigure you may set the primary scanner to Edge (S), but the other scanners must remain in Serial (S): Host Primary Scanner Secondary Scanner E S S Secondary Scanner MS-890 Industrial Automation Scanner User Manual 3-19

64 Daisy Chain Scanner ID Daisy Chain Scanner ID Note: Scanner IDs can also be assigned in Daisy Chain (Aux Port Mode) (page 3-14). Usage: Definition: Scanner Number Scanner ID This command provides a convenient way to assign custom daisy chain IDs to specific scanners that were assigned during the daisy chain autoconfigure process. Assigns a new daisy chain ID to a daisy chain secondary scanner. The command is sent to the master scanner to configure the other secondary scanners. Definition: Specifies the target scanner (by sequential number) which will be receiving the new daisy chain ID. The master scanner is always 0 (zero). All secondary scanners are numbered 1...n in the order that they are connected. Note: These numbers are for assigning IDs only and are not changeable. Serial Cmd: <K151,daisy chain scanner #,daisy chain scanner ID> Options: 1...n (0 for the master scanner) Definition: A two-character user-defined ASCII message identifying a scanner in the daisy chain. Serial Cmd: <K151,daisy chain scanner #,scanner ID> Default: Sequential numbering of scanner units resulting from the Daisy Chain Autoconfigure <K150DAISY> command; for example: ID Master = 1/; ID Scanner 1 = 2/; ID Scanner 2 = 3/; etc. Options: Any two characters except NUL, <, >, or,. Note: See also Chapter 13, Output Format. Note: After a secondary scanner accepts a new ID, it automatically invokes a reset-with-save command MS-890 Industrial Automation Scanner User Manual

65 Communications Auxiliary/Configuration Port System Data Note: Do not use Auxiliary Port in a daisy chain operation. Auxiliary Port Status Note: This command only applies if Auxiliary Port Mode is set to Command Processing. See Command Processing (Aux Port Mode) on page Usage: To check symbol data and error messages via the Aux Port. Definition: When enabled, system data, including decoded data and diagnostic warning messages, will be routed to the Aux Port. Serial Cmd: <K146,aux port status,config port status> Default: Disabled Options: 0 = Disabled 1 = Enabled Configuration Port Status Usage: To check symbol data and error messages via the configuration port. Definition: When enabled, system data, including decoded data and diagnostic warning messages, will be routed to the 9-pin configuration port. Serial Cmd: <K146,aux port status,config port status> Default: Enabled Options: 0 = Disabled 1 = Enabled Important: Enable Data Out 9-Pin when using the configuration port. MS-890 Industrial Automation Scanner User Manual 3-21

66 Preamble Preamble Preamble Status Usage: Used for identifying and controlling incoming data. For example, defining the preamble as a carriage return and a line feed causes each decoded message to be displayed on its own line. Definition: Defines a one to four character data string that can be added to the front of the decoded data. Serial Cmd: <K141,status,preamble character(s)> Default: Disabled Options: 0 = Disabled 1 = Enabled (within any protocol) Preamble Character(s) Serial Cmd: <K141,status,preamble character(s)> Default: ^M corresponds to: carriage return/nul/nul/nul. Options: Up to four user-defined ASCII characters, including control characters. Within a Serial Command To enter control characters within a serial command, hold down the control key while typing the desired character. Example: <K141,1,CTRL-m> to enter ^M Within an Embedded Menu Control characters entered on the command line are displayed in the menu as mnemonic characters, such as: <CR><NUL><NUL><NUL>. To enter a control character from within an embedded menu, first type in a space (with the space key). This has the effect of allowing the control key to be recognized as a part of the control character. Next hold down the control key while typing the desired character. Example: Space CTRL-m to enter ^M 3-22 MS-890 Industrial Automation Scanner User Manual

67 Postamble Communications Postamble Status Usage: Used for identifying and controlling incoming data. For example, defining the postamble as a carriage return and a line feed causes each decoded message to be displayed on its own line. Definition: Defines a one- to four-character data string that can be added to the end of the decoded data. Serial Cmd: <K142,status,postamble character(s)> Default: Enabled Options: 0 = Disabled 1 = Enabled Postamble Character(s) Serial Cmd: <K142,status,postamble character(s)> Default: ^M^J corresponds to carriage return/line feed/nul/nul, as displayed in the menu. Options: Up to four user-defined ASCII characters, including control characters. Within a Serial Command To enter control characters within a serial command, hold down the control key while typing the desired character. Example: <K142,1,CTRL-m CTRL-j> to enter ^M^J. Within an Embedded Menu Control characters entered on the command line are displayed in the menu as mnemonic characters, such as: <CR><LF><NUL><NUL> To enter a control character from within an embedded menu, first type in a space (with the space key). This has the effect of allowing the control key to be recognized as a part of the control character. Next hold down the control key while typing the desired character. Example: Space CTRL-m Space CTRL-j to enter ^M^J. MS-890 Industrial Automation Scanner User Manual 3-23

68 LRC Status LRC Status (Longitudinal Redundancy Check) Usage: Used when extra data integrity is required. Definition: An error-checking routine that verifies the accuracy of transmissions. It is the exclusive OR of all characters following the STX (start of text) up to and including the ETX (end of text). What this means is that the binary representation of all the characters in a transmissions are cumulatively added in a column and each resulting odd integer is assigned a 1 and each even integer a 0 (two 1s = 0, two 0s = 0, a 1 and a 0 = 1). The extra LRC character is then appended to the transmission and the receiver connected to the host port performs the same addition and compares the results. Serial Cmd: <K145,status> Default: Disabled Options: 0 = Disabled 1 = Enabled 3-24 MS-890 Industrial Automation Scanner User Manual

69 Intercharacter Delay Communications Usage: Definition: Used only when a host cannot receive data quickly enough and there is enough time between symbols to allow data to be completely transferred. It is rarely used since any setting other than zero will slow down communications. For example, a 200 setting will result in a 1/5 second delay between each character that is transmitted. The time interval in milliseconds between individual characters transmitted from the scanner to the host. Serial Cmd: <K144,intercharacter delay> Default: 0 Options: 0 to 255 (in milliseconds) Note: 0 causes no delay between characters. MS-890 Industrial Automation Scanner User Manual 3-25

70 Response Timeout Response Timeout Usage: Definition: Used only when a response is required from the host. While in Multidrop, if the scanner does not receive an ACK or NAK from the host after sending polled data, it will act on a fault. The scanner can be set to wait indefinitely by setting Response Timeout to zero. Time the scanner will wait before timing out if ACK, NAK, and ETX are enabled, and a host response is expected. Serial Cmd: <K143,response timeout> Default: Options: 2 (x 10 = 20 ms) 0 to 255 in 10 ms increments (0 to 2.55 seconds) (A 0 setting causes an indefinite wait.) 3-26 MS-890 Industrial Automation Scanner User Manual

71 4 Read Cycle Contents Read Cycle by ESP Read Cycle Serial Commands Multisymbol Trigger External Trigger State Serial Trigger Start Character (Non-Delimited) Stop Character (Non-Delimited) End of Read Cycle Good Decode Reads Gain Settings Focus Scan Speed Automatic Gain Control (AGC) Settings Maximum Element Tracking Adjustment After you ve established communications and completed basic read rate testing, you will need to address the spatial and timing parameters associated with your application. In a typical operation, a bar-coded item moves along a line past a scanner. A trigger or timer activates a read cycle during which the scanner actively searches for symbols. You will need to decide how to initiate the read cycle and how and when to end it. Note: When assigning characters in user-defined fields, the characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. Note: You can learn the current setting of any parameter by inserting a question mark after the number, as in <K100?>. To see all K commands, send <K?>. Note on Serial Commands: To preserve continuity with other Microscan products, some serial configuration commands may include 0s or 1s as placeholders. In order for a these commands to be implemented, the parameter values or a comma must be included. MS-890 Industrial Automation Scanner User Manual 4-1

72 Read Cycle by ESP Read Cycle by ESP Click this button to bring up the Read Cycle menu. To change a setting, double-click the setting and use your cursor to scroll through the options. To open nested options, single-click the +. Read Cycle Serial Commands Command Title Trigger Serial Trigger Character External Trigger State End of Read Cycle Good Decode Reads Multisymbol Start Serial Trigger Character End Serial Trigger Character Scan Speed Maximum Element Gain Settings AGC Settings Focus Tracking Adjustment Command Format <K200,trigger mode,trigger filter duration> <K201,trigger character> <K202,external trigger state> <K220,end of read cycle mode,read cycle timeout> <K221,number before output,mode> <K222,number of symbols,multisymbol separator> <K229,start trigger character> <K230,end trigger character> <K500,scan speed> <K502,maximum element> <K504,gain adjustment,agc mode> <K505,symbol detect status,minimum number of transitions> <K508,focus position> <K520,tracking adjustment> 4-2 MS-890 Industrial Automation Scanner User Manual

73 Multisymbol Read Cycle Usage: Multisymbol is commonly used in shipping applications where a shipping symbol contains individual symbols for part number, quantity, etc. This feature allows one trigger to pick up all the symbols. AIAG and EAN-128 are two application standards that address this need. Definition: Multisymbol allows the user to define up to 12 symbols that can be read in a single read cycle. Conditions: The following conditions apply: 1. Each symbol must be different to be read unless they appear in the scan line at the same time. 2. The maximum number of characters in a read cycle is for all symbols. 3. The maximum number of characters the scanner can transmit is calculated by: Preamble + maximum number of symbols * (aux id + symbology id + maximum symbol length + quality output + ((number of insertion cells x cell length)+ separator) + postamble + LRC = All No Read messages are posted at the end of the data string. 5. If more than one symbol is within the scan beam at the same time, symbol data may not be displayed in the order of appearance. 6. If Matchcode Type is set to Sequential or if Trigger is set to Continuous Read 1 Output, Number of Symbols will default to 1 (if set to any number greater than 1). Number of Symbols Definition: Number of Symbols is the number of different symbols that can be read in a single read cycle. Conditions: The following conditions apply: 1. When Number of Symbols is set to Single, the read cycle ends when one symbol is decoded and output. 2. When Number of Symbols is set to Multiple, all decoded symbol data (for both the same and different symbols) are output while the read cycle is active and/or no timeout has occurred. Serial Cmd: <K222,number of symbols,multisymbol separator> Default: 1 Options 1 to 12 MS-890 Industrial Automation Scanner User Manual 4-3

74 Multisymbol Multisymbol Separator Usage: Definition: ESP: Used to delimit or separate data fields with a user defined character. The character that s inserted between each symbol scanned when Multisymbol is set to any number greater than 1. To select a new multisymbol separator, double-click on Separator and select a character in the popup window. Serial Cmd: <K222,number of symbols,multisymbol separator> Note: If Multisymbol Separator has been changed to any character other than the default comma and you wish to re-define the separator as a comma, use ESP or the embedded menu. Default:, (comma) Options: Any available ASCII character, except NUL, <, >, and,. 4-4 MS-890 Industrial Automation Scanner User Manual

75 Trigger Read Cycle Trigger Mode Note: When doing calibration or read rate testing, the current trigger setting will be disregarded. Note: This command does not need to be followed by an <A> command. Definition: Serial Cmd: Default: Options: The type of trigger event that will initiate the read cycle. <K200,trigger mode,trigger filter duration> Continuous Read 0 = Continuous Read 1 = Continuous Read 1 Output 2 = External Level 3 = External Edge 4 = Serial Data 5 = Serial Data and External Edge Continuous Read Usage: Continuous Read is useful in testing symbol readability or scanner functions. It is not recommended for normal operations. Definition: In Continuous Read, trigger input options are disabled, the scanner is always in the read cycle, and it will attempt to decode and output every scan crossing a symbol. When To Output and No Read options have no effect on Continuous Read. Serial Cmd: <K200,0> MS-890 Industrial Automation Scanner User Manual 4-5

76 Trigger Continuous Read 1 Output Usage: Continuous Read 1 Output can be useful in applications where it is not feasible to use a trigger and all succeeding symbols contain different information. It is also effective in applications where the objects are hand-presented. Definition: In Continuous Read 1 Output the scanner self-triggers whenever it decodes a new symbol or a timeout occurs. If End Of Read Cycle is set to Timeout and the symbol doesn't change, the scanner will repeat the output at the end of each timeout period. For example, if Timeout is set to one second, the scanner sends the symbol data immediately and repeats the output at intervals of one second for as long as the symbol continues to be scanned. If End Of Read Cycle is set to New Trigger, the scanner will send the current symbol data immediately, but send it only once. A new symbol appearing in the scanner s range will be read and sent immediately provided it is not identical to the previous symbol read. Serial Cmd: <K200,1> Caution: In automated environments, Continuous Read 1 Output is not recommended because there is no one to verify that a symbol was missed. Note: If Trigger is set to Continuous Read 1 Output, Number of Symbols will default back to 1 (if set to any number greater than 1). 4-6 MS-890 Industrial Automation Scanner User Manual

77 External Trigger Level Read Cycle Initiate Read Cycle: Object #1, moving in front of the detector beam, causes a change in the trigger state, which initiates the read cycle. End Read Cycle: The same object, moving out of the detector beam, causes another change in the trigger state, which ends the read cycle. Usage: This mode is effective in an application where the speeds of the conveying apparatus are variable and the time the scanner spends scanning each object is not predictable. It also allows the user to determine if a No Read has occurred. Definition: External Level allows the read cycle to begin when a trigger (change of state) from an external sensing device is received. The read cycle endures until the object moves out of the sensor range and the active trigger state changes again. Serial Cmd: <K200,2> Important: Level and Edge apply to the active logic state (Open or Closed) that exists while the object is in a read cycle, between the rising edge and falling edge. Rising edge is the trigger signal associated with the appearance of an object. Falling edge is the trigger signal associated with the subsequent disappearance of the object. Note: In External Trigger Level, sending a non-delimited start serial character will start a read cycle and sending a non-delimited stop serial character will end it. See Start Character (Non-Delimited) and Stop Character (Non-Delimited) on page MS-890 Industrial Automation Scanner User Manual 4-7

78 Trigger External Trigger Edge Initiate Read Cycle: Object # 1, moving in front of the detector beam, causes a change in the trigger state, which initiates the read cycle. Initiate Second Read Cycle: Object # 2, moving in front of the detector beam, causes another change in the trigger state. This signal initiates a new read cycle and ends the previous read cycle unless Timeout is enabled and a good read or timeout has not occured. Usage: This mode is highly recommended in any application where conveying speed is constant or if spacing, object size, or timeouts are consistent. Definition: External Trigger Edge, as with Level, allows the read cycle to begin when a trigger (change of state) from an external sensing device is received. However, the passing of an object out of sensor range does not end the read cycle. The read cycle ends with a good read output or, depending on End of Read Cycle setting, a timeout or new trigger occurs.external Trigger Edge, as with Level, allows the read cycle to begin when a trigger (change of state) from an external sensing device is received. However, the passing of an object out of sensor range does not end the read cycle. The read cycle ends with a good read or with a No Read when a No Decode Timeout occurs. Serial Cmd: <K200,3> Important: Level and Edge apply to the active logic state (Open or Closed) that exists while the object is in a read cycle, between the rising edge and falling edge. Rising edge is the trigger signal associated with the appearance of an object. Falling edge is the trigger signal associated with the subsequent disappearance of the object. Note: In External Trigger Level, sending a non-delimited start serial character will start a read cycle and sending a non-delimited stop serial character will end it. See Start Character (Non-Delimited) and Stop Character (Non-Delimited) on page MS-890 Industrial Automation Scanner User Manual

79 Serial Data Read Cycle Usage: Serial Data is effective in a highly controlled environment where the host knows precisely when the object is in the scan zone. It is also useful in determining if a No Read has occurred. Definition: In Serial Data, the scanner accepts an ASCII character from the host or controlling device as a trigger to start a read cycle. A Serial Data trigger behaves the same as an External Edge trigger. Serial Cmd: <K200,4> Serial Data and External Edge Usage: Serial Data and External Edge is seldom used but can be useful in an application that primarily uses an external sensing device but occasionally needs to be manually triggered. An auxiliary terminal can be connected to the Aux Port so the user can send the serial trigger character through the scanner to the host. Definition: In this mode the scanner accepts either a serial ASCII character or an external trigger pulse to start the read cycle. Serial Cmd: <K200,5> MS-890 Industrial Automation Scanner User Manual 4-9

80 Trigger Trigger Filter Duration Usage: Definition: Trigger Filter Duration is useful where trigger bounce could cause false triggers. Trigger Filter Duration can prevent trigger bounce from falsely triggering the scanner by limiting the time in which trigger pulses can be received. Serial Cmd: <K200,trigger mode,trigger filter duration> Default: Options: 320 (10 ms) 0 to (0 to 2.047s in 31.25µs steps) 4-10 MS-890 Industrial Automation Scanner User Manual

81 External Trigger State Read Cycle Note: External Level, External Edge, or Serial Data and External Edge trigger mode must be enabled for External Trigger to take effect. Usage: Definition: Serial Cmd: Default: Users can select the trigger state that will operate with their systems. (If using an object detector, use Active Closed.) When enabled for Active Closed the triggering device imposes a current on the optoisolator to activate the read cycle. When enabled for Active Open the triggering device interrupts the current to the optoisolator to activate the read cycle. <K202,external trigger state> Active closed Options: 0 = Active open 1 = Active closed MS-890 Industrial Automation Scanner User Manual 4-11

82 Serial Trigger Serial Trigger Usage: Definition: Rules for Trigger Modes Useful in applications where a read cycle needs to be initiated and/or ended by user-defined serial characters. An online host command composed of a single ASCII host serial trigger character that initiates or ends the read cycle. Trigger characters are of two types: delimited and non-delimited. A delimited character is enclosed within angle bracket delimiters < >. A non-delimited trigger character is one that either starts or ends the read cycle and is NOT enclosed by delimiters such as < >. In External Edge the scanner looks only for the Start Trigger Character and ignores any End Trigger Character that may be defined. In External Level, the Start Trigger Character begins the read cycle and an End Trigger Character ends it. Note that even after a symbol has been decoded and the data transmitted, the scanner remains in External Level trigger read cycle until a Stop character is received. In Serial Data and External Edge trigger mode, command, either a Start Trigger Character or a hardware trigger can start an Edge trigger read cycle. Serial Trigger Character (Delimited) Usage: Useful in applications where a single serial character enclosed in angle brackets initiates the read cycle. Definition: A delimited trigger character is one that starts the read cycle, is enclosed by delimiters such as < >, and can only be sent when the trigger mode is set to Serial Data or Serial Data and External Edge. Serial Cmd: <K201,serial trigger character> Default: ^] (corresponds to <GS> displayed in the embedded menu) Options: Any single ASCII character, including control characters, except NUL (00 in hex), an existing host command character, or an online protocol character. Control characters entered on the command line are displayed in the menu as mnemonic characters. Note: Serial Data or Serial Data and External Edge triggering mode must be enabled for Serial Trigger Character to take effect MS-890 Industrial Automation Scanner User Manual

83 Start Character (Non-Delimited) Read Cycle Usage: Useful in applications where a different character is required to start a read cycle. Works with External Edge, External Level, and Serial Data and External Edge. Definition: A single ASCII host serial trigger character that starts the read cycle and is not enclosed by delimiters such as < and >. Serial Cmd: <K229,start trigger character> Default: NUL (disabled) Options: Two hex digits representing an ASCII character except <, >, XON, and XOFF. Stop Character (Non-Delimited) Usage: Useful in applications where a different character is required to end a read cycle. Works with External Level only. Definition: A single ASCII host serial trigger character that ends the read cycle and is not enclosed by delimiters such as < and >. Serial Cmd: <K230,stop trigger character> Default: NUL (disabled) Options: Two hex digits representing an ASCII character except <, >, XON, and XOFF. MS-890 Industrial Automation Scanner User Manual 4-13

84 End of Read Cycle End of Read Cycle Note: When to Output must be set to End of Read Cycle before this command can be active. Definition: The read cycle is the time during which the scanner will attempt to read and decode a symbol. At the end of a read cycle the scanner stops reading symbols and sends the symbol data or No Read message to the host. End of Read Cycle Mode Definition: A read cycle can be terminated by a new trigger, a timeout, or a combination of both. Serial Cmd: <K220,end of read cycle,read cycle timeout> Default: Timeout Options: 0 = Timeout 1 = New Trigger 2 = Timeout and New Trigger Note: When operating in Continuous Read or Continuous Read 1 Output, the scanner is always in the read cycle. Timeout Usage: Definition: Typically used with Serial or Edge and Continuous One. It is effective in highly controlled applications when the maximum length of time between objects can be predicted. It assures that a read cycle ends before the next bar-coded object appears, giving the system extra time to decode and transmit the data to the host. Timeout ends the read cycle when the time set in Read Cycle Timeout elapses or times out. If in Continuous Read 1 Output, a timeout initiates a new read cycle and allows the same symbol to be read again. With either External Edge, Serial Data, or Serial Data and External Edge enabled, a timeout ends the read cycle and symbol data or a No Read message is sent to the host. With External Level enabled, the read cycle does not end until the falling edge trigger or a timeout occurs. The next read cycle does not begin until the next rising edge trigger MS-890 Industrial Automation Scanner User Manual

85 New Trigger Read Cycle Usage: Definition: New Trigger is an effective way to end a read cycle when objects move past the scanner at irregular intervals (not timing-dependent). New Trigger ends the current read cycle and initiates a new one when a new trigger occurs. New Trigger refers only to a rising edge trigger. With either External Edge, Serial, or Serial or Edge enabled, an edge or serial trigger ends a read cycle and initiates the next read cycle. In the case of External Level, a falling edge trigger ends the read cycle but the next read cycle does not begin until the occurrence of the next rising edge trigger. Note: When New Trigger is enabled and if not in External Level mode, Laser On/Off will have no effect. When No Reads occur, the laser will remain on. Timeout and New Trigger Usage: Definition: Useful in applications that require an alternative way to end the read cycle. For example, if an assembly line should stop completely or the intervals between objects are highly irregular. Timeout and New Trigger is identical to Timeout, except that a timeout or a new trigger (whichever occurs first) ends the read cycle. MS-890 Industrial Automation Scanner User Manual 4-15

86 End of Read Cycle Read Cycle Timeout Usage: Useful in many tightly controlled applications which require a read cycle to end before the next object appears and therefore need the flexibility of a timeout adjustment. Definition: Read Cycle Timeout is the time span of the read cycle and is represented in 10 ms increments. It is used in conjunction with External Edge or Serial Trigger. Serial Cmd: <K220,end of read cycle,read cycle timeout> Default: 100 (x 10 ms) Options: 0 to (Divide any positive number entered by 100 to determine the time in seconds.) Note: A minimum setting of 2 is recommended. Note: Timeout or Timeout or New Trigger under End of Read Cycle must be enabled for Read Cycle Timeout to take effect MS-890 Industrial Automation Scanner User Manual

87 Good Decode Reads Read Cycle Usage: This is a very useful feature to increase reliability of reads for symbologies that do not have internal error checking such as Pharmacode. Definition: The number of decodes (from 1 to 31) required per symbol before a symbol s decoded data is sent. It requires the scanner to successfully decode a symbol a designated number of times (not necessarily consecutively) before it is sent. If it doesn t achieve the number of good reads during the read cycle, then a No Read will be sent. Note: Higher settings will decrease throughput speed. Serial Cmd: <K221,good decode reads,mode> Default: 1 Options: 1 to 31 Good Decode Output Mode Definition: Affects how the scanner counts symbols that it reads successfully. Serial Cmd: <K221,good decode reads,mode> Default: Non-Consecutive Options: 0 = Non-Consecutive 1 = Consecutive MS-890 Industrial Automation Scanner User Manual 4-17

88 Gain Settings Gain Settings The settings in this section are typically adjusted by Calibration, or by qualified technicians. They are included here for special applications. Before making changes to individual commands in this section, it would be advisable to make a written record of current settings. Gain Adjustment Usage: Can be useful for fine-tuning gain or when portions of analog signals spike as in the case of specular reflection or extraneous noise. Caution: Changes to Gain are typically done by qualified technicians in Calibration. See Chapter 9, Calibration. Definition: Sets a voltage amplitude value for the analog circuitry. Serial Cmd: <K504,gain adjustment,agc mode> Default: Default is 40 (nominal). Gain is optimized at the factory before shipment; the default value may not be 40. Options: 0 to 255 AGC Mode Definition: Tracks peak signals and selects an amplitude reference point to sample the analog signals for converting to digital. Serial Cmd: <K504,gain adjustment,agc mode> Default: Disabled Options: 0 = Disabled 1 = Enabled 4-18 MS-890 Industrial Automation Scanner User Manual

89 Focus Read Cycle Focus is generally set during the Calibration routine (see Chapter 9, Calibration). However, in certain applications involving specific focal lengths, manual control of focus may be appropriate. Focus Position Definition: Allows the user to change the focus position setting. Serial Cmd: <K508,focus position> Default: 0 Options: 0 to 40 MS-890 Industrial Automation Scanner User Manual 4-19

90 Scan Speed Scan Speed Definition: Allows the user to set the number of scans per second by controlling the spinning mirror motor speed. Serial Cmd: <K500,scan speed> Default: 400 Options: 400 to MS-890 Industrial Automation Scanner User Manual

91 Automatic Gain Control (AGC) Settings Important: AGC settings apply to both AGC and symbol detection. Read Cycle Symbol Detect Status Usage: During the read cycle, the scanner counts the number of bar and space transitions defined in the Transition Counter. If the count matches or exceeds the threshold, the scanner will perform AGC routines. Definition: AGC is the acronym for Automatic Gain Control. AGC increases the depth of field by attempting to maintain signal strength at a constant level regardless of the range of the symbol. Serial Cmd: <K505,symbol detect status,minimum number of transitions> Default: Disabled Options: 0 = Disabled 1 = Enabled Minimum Number of Transitions Usage: Can be useful in certain application where extraneous objects in the field of view might require a higher threshold. Definition: Determines the number of bar/space transitions that must be read before a symbol is considered present and AGC can be resolved. Serial Cmd: <K505,symbol detect status,minimum number of transitions> Default: 14 Options: 1 to 255 MS-890 Industrial Automation Scanner User Manual 4-21

92 Maximum Element Maximum Element Definition: Maximum Element represents the maximum bar element width that is allowed before a video reset occurs (default to white). Caution: Do not change this parameter unless instructed by a Microscan representative. Serial Cmd: <K502,maximum element> Default: 400 (x 0.01% of scan) Options: 50 to MS-890 Industrial Automation Scanner User Manual

93 Tracking Adjustment Read Cycle Definition: Sets a tracking value for the scanner s analog circuitry. Changes to tracking adjustment should be made by Autocalibration. Serial Cmd: <K520,tracking adjustment> Default: 40 Options: 5 to 127 MS-890 Industrial Automation Scanner User Manual 4-23

94 Tracking Adjustment 4-24 MS-890 Industrial Automation Scanner User Manual

95 5 Symbologies Contents Symbologies by ESP Symbologies Serial Commands Code Code 128 / EAN Interleaved 2 of Codabar UPC/EAN Code Pharmacode PDF Narrow Margins / Symbology ID Background Color Autodiscriminate This section describes the various symbol types that can be read and decoded by the scanner. Code 39 is enabled by default. To enable all symbologies, right-click Autodiscrimination under Symbol Type in the Utilities menu and select Enable, or send a <P> serial command to the scanner from the Terminal window. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. MS-890 Industrial Automation Scanner User Manual 5-1

96 Symbologies by ESP Symbologies by ESP Click this button to bring up the Symbologies menu. To open nested options, single-click the +. To change a setting, double-click the setting and use your cursor to scroll through the options. Symbologies Serial Commands Command Title Narrow Margins/Symbology ID Background Color Code 39 Codabar Interleaved 2 of 5 UPC/EAN Code 128/EAN-128 Code 93 PDF417 Pharmacode Command Format <K450,narrow margins status,symbology identifier status> <K451,background color> <K470,status,check character status,check character output status, large intercharacter gap,fixed symbol length status,fixed symbol length,full ASCII set> <K471,status,start and stop match,start and stop output, large intercharacter gap,fixed symbol length status,fixed symbol length,check character type,check character output> <K472,status,check digit status,check digit output,symbol length #1,symbol length #2,guard bar status,range mode status> <K473,UPCstatus,EAN status,supplemental status,separator status, separator character,supplemental type> <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> <K475,status,fixed symbol length status,symbol length> <K476,status,raster sweeps before decode attempt,fixed symbol length status,symbol length,decode at end of read> <K477,status,fixed symbol length status,symbol length,minimum number of bars,bar widths,direction,fixed threshold value> 5-2 MS-890 Industrial Automation Scanner User Manual

97 Code 39 Usage: Definition: Code 39 is considered the standard for non-retail applications. Symbologies An alphanumeric symbol with unique start/stop symbol patterns, composed of 9 black and white elements per character, of which 3 are wide. Code 39 Status Serial Cmd: Default: <K470,status,check character status,check character output,large intercharacter gap,fixed symbol length status,symbol length,full ASCII set> Enabled Note: This is the only symbol type enabled by default. Options: 0 = Disabled 1 = Enabled Check Character Status (Code 39) Serial Cmd: Default: <K470,status,check character status,check character output,large intercharacter gap,fixed symbol length status,symbol length,full ASCII set> Disabled Options: 0 = Disabled 1 = Enabled Check Character Output (Code 39) Usage: Definition: Serial Cmd: Default: Check Character Output Status, added to the symbol, provides additional security. When enabled, the check character is read and sent along with the symbol data. When disabled, symbol data is sent without the check character. Note: With Check Character Output Status and an External or Serial trigger option enabled, an invalid check character calculation will cause a No Read message to be transmitted at the end of the read cycle. <K470,status,check character status,check character output,large intercharacter gap,fixed symbol length status,symbol length,full ASCII set> Disabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 5-3

98 Code 39 Large Intercharacter Gap (Code 39) Usage: Definition: Serial Cmd: Default: Large Intercharacter Gap is helpful for reading symbols that are printed out of specification. Caution: Do not use Large Intercharacter Gap with Narrow Margins enabled since a large intercharacter gap (over 3x) could cause a narrow margins (5x) to be interpreted as an intercharacter gap. When enabled, the scanner can read symbols with gaps between symbol characters that exceed three times (3x) the narrow element width. <K470,status,check character status,check character output,large intercharacter gap,fixed symbol length status,symbol length,full ASCII set> Disabled Options: 0 = Disabled 1 = Enabled Fixed Symbol Length Status (Code 39) Usage: Definition: Serial Cmd: Default: Helps prevent truncations and increases data integrity by ensuring that only a fixed symbol length will be accepted. When enabled, the scanner will check the symbol length against the symbol length field. If disabled, any length is considered a valid symbol. <K470,status,check character status,check character output status,large intercharacter gap,fixed symbol length status,fixed symbol length,full ASCII set> Disabled Options: 0 = Disabled 1 = Enabled Symbol Length (Code 39) Definition: Specifies the exact number of characters that the scanner will recognize (this does not include start and stop and check character characters). The scanner ignores any symbol not having the specified length. Serial Cmd: <K470,status,check character status,check character output,large intercharacter gap,fixed symbol length status,fixed symbol length,full ASCII set> Default: 10 Default: 1 to MS-890 Industrial Automation Scanner User Manual

99 Full ASCII Set (Code 39) Usage: Definition: Serial Cmd: Default: Symbologies Must be enabled when reading characters outside the standard character set (0-9, A-Z, etc.) User must know in advance whether or not to use Full ASCII Set option. Since Full ASCII Set requires two symbol words to encode one character, it is less efficient. Standard Code 39 encodes 43 characters; zero through nine, capital A through capital Z, minus symbol, plus symbol, forward slash, space, decimal point, dollar sign and percent symbol. When Full ASCII Set is enabled, the scanner can read the full ASCII character set, from 0 to 255. <K470,status,check character status,check character output,large intercharacter gap,fixed symbol length status,symbol length,full ASCII set> Disabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 5-5

100 Code 128/EAN-128 Code 128/EAN-128 Usage: Definition: Code 128 Status Serial Cmd: Default: Code 128/EAN-128 is a smaller symbology, and is useful in applications with tight spots and high security needs. A very dense alphanumeric symbology. It encodes all 128 ASCII characters; it is continuous, has variable length, and uses multiple element widths measured edge to edge. <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Disabled Options: 0 = Disabled 1 = Enabled (Serial Standard) Note: Code 128 must be Enabled for EAN-128 to function. Fixed Symbol Length Status (Code 128) Symbol Length (Code 128) 2 = Edge 3 = Serial Standard and Edge Definition: When enabled, the scanner will check the symbol length against the symbol length field. When disabled, any length is considered a valid symbol. Serial Cmd: <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Default: Disabled Options: 0 = Disabled 1 = Enabled Usage: Fixed Symbol Length helps prevent truncations and increases data integrity by ensuring that only one symbol length will be accepted. Definition: Specifies the exact number of characters that the scanner will recognize (this does not include start and stop and check characters). The scanner ignores any symbol not having the specified length. Serial Cmd: <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Default: 10 Options: 1 to 128 Note: Fixed Symbol Length Status must be enabled for Symbol Length to take effect. 5-6 MS-890 Industrial Automation Scanner User Manual

101 EAN-128 Status Usage: Definition: Symbologies Sometimes called the shipping code, it is used as a standard to track a product from site to site with a single symbol that contains categories of information identifiable across industries worldwide. A subset of Code 128, with extended features using application identifiers to define the meaning and format of fields that immediately follow them. For more information, refer to the AIM website at: Serial Cmd: Default: <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Note: Code 128 serial command fields for K474 precede EAN-128. Disabled Options: 0 = Disabled 1 = Enabled 2 = Required If set to Enabled, symbols can be read with or without a function 1 character in the first position. If set to Required, the symbol must have a function 1 in the first position and conform to EAN format in order to decode the symbol. Note: Code 128 must also be Enabled for EAN-128 to function. MS-890 Industrial Automation Scanner User Manual 5-7

102 Code 128/EAN-128 Output Format (EAN-128) Usage: Definition: Serial Cmd: Default: Options: Standard: Application Record: Application Record is useful in applications in which the software can use application record formatting to help automate the processing of its EAN-128 data. Offers an option between Standard EAN-128 and Application Record format. <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Standard 0 = Standard 1 = Application Record When set to Standard, EAN-128 application identifiers and data fields are sent, but none of the formatting (separators, parentheses, padding) will be included. Application Record is a variation of EAN-128 that allows the user to define separators between data fields, enclose application identifiers in parentheses, and enable padding (zeros) for variable length fields. Note: If an illegal Application Record format is detected, the scanner will process it as a No Read and output a No Read message (if enabled). Application Record Separator Status (EAN-128) Definition: Serial Cmd: Default: When enabled, a separator character is inserted between application records. <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Disabled Options: 0 = Disabled 1 = Enabled Application Record Separator Character (EAN-128) Definition: Serial Cmd: Default: Options: Defines an ASCII character as an application record separator. <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance>, (comma) User Defined ASCII character Note: Output Format must be set to Application Record before this parameter can take effect. 5-8 MS-890 Industrial Automation Scanner User Manual

103 Application Record Brackets Status (EAN-128) Definition: Serial Cmd: Default: Symbologies When enabled, parentheses ( ) are added to enclose application identifiers. <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Disabled Options: 0 = Disabled 1 = Enabled Note: Output Format must be set to Application Record before this parameter can take effect. Application Record Padding Status (EAN-128) Definition: Padding is the insertion of zeros to make up the maximum length of a variable application record data field, except for the last field which does not require padding. When enabled, padding is included. When disabled, padding is omitted. Note: Padding is never added to fixed length fields or to the last data field of a symbol. Enabling or disabling Record Padding will have no effect on these. Serial Cmd: <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Default: Disabled Options: 0 = Disabled 1 = Enabled Note: Output Format must be set to Application Record before this parameter can take effect. Minimum Ratio Distance (Code 128) Definition: Determines the error tolerance level. Normal enforces a requirement for normal error tolerance. High enforces a requirement for high element-to-element quality. Highest enforces a requirement for very high element-to-element quality. Serial Cmd: <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> Default: Normal Options: 0 = Normal 1 = High 2 = Highest MS-890 Industrial Automation Scanner User Manual 5-9

104 Interleaved 2 of 5 Interleaved 2 of 5 Usage: Definition: Interleaved 2 of 5 has been popular because it is the most dense symbol for printing numeric characters less than 10 characters in length; however, Microscan does not recommend this symbology for any new applications because of inherent problems (truncation, for example). A dense, continuous, self-checking, numeric symbology. Characters are paired together so that each character has five elements, two wide and three narrow, representing numbers 0 through 9, with the bars representing the first character and the interleaved spaces representing the second character. (A check digit is highly recommended.) Important: You must set Symbol Length in order to decode I 2/5 symbols. Interleaved 2 of 5 Status Serial Cmd: Default: <K472,status,check digit status,check digit output status,symbol length #1,symbol length #2,guard bar status,range mode> Disabled Options: 0 = Disabled 1 = Enabled Check Digit Status (Interleaved 2 of 5) Usage: Definition: Serial Cmd: Default: Typically not used but can be enabled for additional security in applications where the host requires redundant check digit verification. An error correcting routine in which the check digit character is added. <K472,status,check digit status,check digit output status,symbol length #1,symbol length #2,guard bar status,range mode> Disabled Options: 0 = Disabled 1 = Enabled Check Digit Output Status (Interleaved 2 of 5) Definition: Serial Cmd: Default: When enabled, a check digit character is sent along with the bar symbol data for added data security. <K472,status,check digit status,check digit output,symbol length #1,symbol length #2,guard bar status,range mode> Disabled Options: 0 = Disabled 1 = Enabled 5-10 MS-890 Industrial Automation Scanner User Manual

105 Symbol Length #1 (Interleaved 2 of 5) Symbologies Usage: With I 2/5, two symbol lengths can be defined. When using only one symbol length in an application, setting Symbol Length #2 to 0 (zero) to ensure data integrity is recommended. Definition: Allows user to define the symbol length. Because I 2/5 is a continuous symbology, it is prone to substitution errors. Hence, a symbol length must be defined and a symbol must contain an even number of digits. Note: If start, stop or check digits are used, they are not included in the symbol length count. Serial Cmd: <K472,status,check digit status,check digit output status,symbol length #1,symbol length #2,guard bar status,range mode> Default: 10 Options: 0 to 128, even Note: Since I 2/5 characters are paired, symbol length must be set to an even number. If Check Digit is enabled, add 2 to your symbol length. For example, if your symbol is 10 characters plus a check digit, then enable Symbol Length for 12. Note: Typically, when printing an I 2/5 symbol with an odd number of digits, a 0 will be added as the first character.note: If both Symbol Length #1 and Symbol Length #2 are set to 0, then I 2 of 5 will be variable. Symbol Length #2 (Interleaved 2 of 5) Usage: If using a second symbol, a zero or any even symbol length from 2 to 64 may be specified. If not using a second symbol, set Symbol Length #2 to 0 to ensure data integrity. Definition: Allows user to define a second symbol length for I 2/5. Serial Cmd: <K472,status,check digit status,check digit output status,symbol length #1,symbol length #2,guard bar status,range mode> Default: 6 Options: 0 to 128, even Since I 2/5 characters are paired, symbol length must be set to an even number. If Check Digit is enabled, add 2 to your symbol length. For example, if your symbol is 10 characters plus a check digit, then enable Symbol Length for 12. Note: Typically, when printing an I 2/5 symbol with an odd number of digits, a 0 will be added as the first character. Note: If both Symbol Length #1 and Symbol Length #2 are set to 0, then I 2 of 5 will be variable. MS-890 Industrial Automation Scanner User Manual 5-11

106 Interleaved 2 of 5 Guard Bar (Interleaved 2 of 5) Note: Whenever Guard Bar is enabled, the presence of guard bars is required for decoding to take place. Usage: Useful when I 2 of 5 multisymbols are enabled to prevent false data output. This typically occurs with highly tilted or skewed symbols. Definition: A guard bar is a heavy bar, at least 2 times the width of the wide bar, surrounding the printed I 2 of 5 symbol and helping to prevent false reads. Serial Cmd: <K472,status,check digit status,check digit output status,symbol length #1, symbol length #2,guard bar,range mode> Default: Disabled Options: 0 = Disabled 1 = Enabled Range Mode (Interleaved 2 of 5) Note: Whenever Guard Bar is enabled, the presence of guard bars is required for decoding to take place. Definition: When enabled, this feature causes symbol length # 1 and symbol length # 2 to form of a range of lengths that can be decoded. For example, if symbol lengths of 10 and 6 are enabled, those are the lengths that can be decoded. Note that either length can serve as the minimum or maximum. Serial Cmd: <K472,status,check digit status,check digit output status,symbol length #1, symbol length #2,guard bar,range mode> Default: Disabled Options: 0 = Disabled 1 = Enabled 5-12 MS-890 Industrial Automation Scanner User Manual

107 Codabar Symbologies Usage: Used in photo-finishing and library applications. Used in some medical applications at one time, but not typically used in newer applications. Definition: Codabar is a 16-character set (0 through 9, and the characters $, :, /,., +, and ) with start/stop codes and at least two distinctly different bar widths. Codabar Status Serial Cmd: Default: <K471,status,start and stop match status,start and stop output status,large intercharacter gap,fixed symbol length status,symbol length,check character type,check character output status> Disabled Options: 0 = Disabled 1 = Enabled Start and Stop Match Status (Codabar) Usage: Definition: Serial Cmd: Default: Used to increase security of symbology. Requires the Codabar start and stop characters (a, b, c, or d) to match before a valid read can occur. <K471,status,start and stop match status,start and stop output status, large intercharacter gap,fixed symbol length status,symbol length,check character type,check character output status> Enabled Options: 0 = Disabled 1 = Enabled Start and Stop Output Status (Codabar) Usage: Definition: Serial Cmd: Default: Used to verify matching. Causes the start and stop characters to be transmitted with symbol data. <K471,status,start and stop match status,start and stop output status, large intercharacter gap,fixed symbol length status,symbol length,check character type,check character status,check character output status> Enabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 5-13

108 Codabar Large Intercharacter Gap (Codabar) Usage: Definition: Serial Cmd: Default: It is helpful for reading symbols that are printed out of specification. Caution: Do not use Large Intercharacter Gap with Narrow Margins enabled since enabling Large Intercharacter Gap (over 3x) could cause a narrow margins (5x) to be interpreted as an intercharacter gap. Instructs the scanner to read symbols with gaps between characters exceeding three times the narrow element width. <K471,status,start and stop match status,start and stop output status,large intercharacter gap,fixed symbol length status,symbol length,check character type,check character output status> Disabled Options: 0 = Disabled 1 = Enabled Fixed Symbol Length Status (Codabar) Usage: Definition: Serial Cmd: Default: Fixed Symbol Length helps prevent truncations and increases data integrity by ensuring that only one symbol length will be accepted. When enabled, the scanner will check the symbol length against the fixed symbol length field. When disabled, any length would be considered a valid symbol. <K471,status,start and stop match status,start and stop output status,large intercharacter gap,fixed symbol length status,symbol length,check character type,check character output status> Disabled Options: 0 = Disabled 1 = Enabled Symbol Length (Codabar) Definition: Specifies the exact number of characters that the scanner will recognize (this does not include start and stop and check character characters). The scanner ignores any symbol not having the specified length. Serial Cmd: <K471,status,start and stop match status,start and stop output status,large intercharacter gap,fixed symbol length status,fixed symbol length,check character type,check character output status> Default: 10 Options: 1 to 128 Note: Fixed Symbol Length Status must be enabled for Symbol Length to take effect. Note: Because of symbology limitations, setting Symbol Length to any number less than four will produce undetermined results MS-890 Industrial Automation Scanner User Manual

109 Symbologies Check Character Type (Codabar) Definition: Serial Cmd: Default: Allows the user to select the check character type Codabar will use. <K471,status,start and stop match,start and stop output status,large intercharacter gap,fixed symbol length status,fixed symbol length,check character type,check character output status> Disabled Options: 0 = Disabled 1 = Modulus 16 2 = NW 7 3 = Both Modulus 16: Used in the photo-finishing market. NW 7: Used in Japanese markets. Check Character Output Status (Codabar) Usage: Definition: Serial Cmd: Default: For additional security a check character can be added to the symbol. When enabled, the check character character is sent along with the symbol data. When disabled, symbol data is sent without the check character. <K471,status,start and stop match,start and stop output status,large intercharacter gap,fixed symbol length status,symbol length,check character type,check character output status> Disabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 5-15

110 UPC/EAN UPC/EAN Usage: Definition: UPC Status Serial Cmd: Default: EAN Status Used primarily in POS application in the retail industry. It is commonly used in applications in combination with Matchcode when there is a need to verify that the right product is being placed in the right packaging. UPC (Universal Product Code) is a fixed length numeric, continuous symbology. UPC can have two- or five-digit supplemental symbol data following the normal symbol. The U.P.C., Version A (UPC-A) symbol is used to encode a 12 digit number. The first digit is the number system character, the next five are the manufacturer number, the next five are the product number, and the last digit is the checksum character. When enabled, the scanner will read UPC-A and UPC-E only. <K473,UPC status,ean status,supplemental status,separator status,separator character,supplemental type> Disabled Options: 0 = Disabled 1 = Enabled Usage: Definition: Serial Cmd: Default: UPC/EAN is the European version of the UPC symbology and is used in European market applications. Note: UPC must be enabled for EAN to take effect. EAN is a subset of UPC. When enabled, the scanner will read UPC version A, UPC version E, EAN 13, and EAN 8. It also appends a leading zero to UPC version A symbol information and transmits 13 digits. If transmitting 13 digits when reading UPC version A symbols is not desired, disable UPC/EAN. Note: The extra character identifies the country of origin. <K473,UPC status,ean status,supplemental status,separator status,separator character,supplemental type> Disabled Options: 0 = Disabled 1 = Enabled 5-16 MS-890 Industrial Automation Scanner User Manual

111 Supplemental Status (UPC/EAN) Usage: Definition: Serial Cmd: Default: Options: Disabled: Enabled: Required: Symbologies Reads Supplementals typically used in publications and documentation. A supplemental is a 2 or 5 digit symbol appended to the main symbol. When set to Enabled or Required, the scanner reads supplemental symbol data that has been appended to the standard UPC or EAN codes. <K473,UPC status,ean status,supplemental status,separator status, separator character,supplemental type> Disabled 0 = Disabled 1 = Enabled 2 = Required UPC Supplementals will not be decoded. When enabled, the scanner will try to decode a main and a supplemental. However, if a supplemental is not decoded, at the end of the read cycle, the main will be sent by itself. The UPC main and supplemental symbols are considered to be one symbol and will be treated as such. When set to Required and either the main or supplemental symbol is not read, a single No Read condition results. The UPC main and supplemental symbols are treated as one symbol. For example, if Supplementals is set to Required, Separator is enabled, and an asterisk is defined as the UPC separator character, then the data will be displayed as: MAIN * SUPPLEMENTAL. Note: Under no circumstances will supplemental symbol data be sent without a main symbol. Note: If additional symbols other than the main or supplemental will be read in the same read cycle, Number of Symbols should be set accordingly. Separator Status (UPC/EAN) Usage: Definition: Serial Cmd: Default: Allows user to distinguish between the main and Supplemental symbols. Allows the user to insert a character between the standard UPC or UPC/EAN symbol and the supplemental symbol when Supplementals is set to Enabled or Required. <K473,UPC status,ean status,supplemental status,separator status,separator character,supplemental type> Disabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 5-17

112 UPC/EAN Separator Character (UPC/EAN) Note: If Separator Character has been changed to any other character and you wish to redefine the separator as a comma, you will need to use ESP or the embedded menu. Note: Whenever Separator Character is defined as a comma (,) sending a <K473,?> command will return the current settings, including the separator character comma which appears after the separator status comma. Usage: Definition: Serial Cmd: Default: Options: As required by the application. Allows the user to change the separator character from a comma to a new character. <K473,UPC status,ean status,supplemental status,separator status, separator character,supplemental type>, (comma) Any ASCII character Supplemental Type (UPC/EAN) Usage: Definition: Serial Cmd: Default: Options: Both: As required by symbology used in application. Allows the user to select 2 character or 5 character supplement, or both. <K473,UPC status,ean status,supplemental status,separator status,separator character,supplemental type> Both 0 = Both 1 = 2 characters only 2 = 5 characters only Either 2 character or 5 character supplementals will be considered valid. 2 Char Only: Only two character supplementals will be considered valid. 5 Char Only: Only five character supplementals will be considered valid MS-890 Industrial Automation Scanner User Manual

113 Code 93 Usage: Definition: Code 93 Status Serial Cmd: Default: Fixed Symbol Length Status (Code 93) Symbologies Used occasionally in the clinical industry. Code 93 is a variable length, continuous symbology employing four element widths. Each Code 93 character has nine modules that may be either black or white. Each character contains three bars and three spaces. <K475,status,fixed symbol length status,fixed symbol length> Disabled Options: 0 = Disabled 1 = Enabled Usage: Definition: Serial Cmd: Default: Helps prevent truncations and increases data integrity by ensuring that only one symbol length will be accepted. When enabled, the scanner will check the symbol length against the symbol length field. When disabled, any length is considered a valid symbol. <K475,status,fixed symbol length status,fixed symbol length> Disabled Options: 0 = Disabled 1 = Enabled Fixed Symbol Length (Code 93) Definition: Specifies the exact number of characters that the scanner will recognize (this does not include start and stop and check characters). The scanner ignores any symbol not having the specified length. Serial Cmd: <K475,status,fixed symbol length status,fixed symbol length> Default: 10 Options: 1 to 128 MS-890 Industrial Automation Scanner User Manual 5-19

114 Pharmacode Pharmacode Usage: Definition: Pharmacode is used mostly with packaging for the pharmaceuticals industry. The symbol encodes up to five different numbers, each with its own color which may be entered in decimal or binary format with a 1 represented by a thick bar and a 0 represented by a thin bar. Bar width is independent of height. In decimal format, each part can be up to In binary format, each input have up to 19 ones and zeros. Note: It is recommended that you disable AGC before enabling Pharmacode. Pharmacode Status Serial Cmd: Default: <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars, bar widths,decode direction,fixed threshold value> Disabled Options: 0 = Disabled 1 = Enabled Fixed Symbol Length Status (Pharmacode) Serial Cmd: Default: <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars,bar widths,,decode direction,fixed threshold value> Disabled Options: 0 = Disabled 1 = Enabled Fixed Symbol Length (Pharmacode) Serial Cmd: <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars,bar widths,decode direction,fixed threshold value> Default: 10 Options: 4 to 16 Minimum Number of Bars (Pharmacode) Serial Cmd: <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars,bar widths,decode direction,fixed threshold value> Default: 4 Options: 4 to MS-890 Industrial Automation Scanner User Manual

115 Bar Widths (Pharmacode) Symbologies Serial Cmd: <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars, bar widths,decode direction,fixed threshold value> Default: Mixed Options: 0 = Mixed 1 = Narrow 2 = Wide Decode Direction (Pharmacode) Definition: Serial Cmd: Default: Specifies the direction that a bar can be read. <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars,bar widths,decode direction,fixed threshold value> Forward Options: 0 = Forward 1 = Reverse Fixed Threshold Value (Pharmacode) Serial Cmd: <K477,status,fixed symbol length status,fixed symbol length,min. no. of bars,bar widths,decode direction,fixed threshold value> Default: 400 Options: 1 to MS-890 Industrial Automation Scanner User Manual 5-21

116 PDF417 PDF417 Note: Calibration does not function with PDF417 symbols. However, you can substitute a Code 128 symbol with the same mil size as your PDF417. When you do this, enable Code 128 and disable Raster scanning. After calibration, switch back to PDF417 and Raster scanning. Usage: Definition: PDF417 Status Serial Cmd: Default: Used in applications where a large amount of information (over 32 characters) needs to be encoded within a symbol, typically where the symbol is transported from one facility to another. For example, an automobile assembly line might use a single symbol with multiple fields of information that will be read at several stations along the way, without reference to a database. A two-dimensional, multi-row (3 to 90), continuous, variable length symbology that has high data capacity for storing up to 2700 numeric characters, 1,800 printable ASCII characters, or 1100 binary character per symbol. Each symbol character consists of 4 bars and 4 spaces in a 17-module structure. <K476,status,raster sweeps before decode attempt,fixed symbol length status,fixed symbol length,decode at end of read> Disabled Options: 0 = Disabled 1 = Enabled Raster Sweeps Before Decode Attempt (PDF417) Usage: Might be useful in dynamic applications where symbols are close together and need to be decoded more quickly than the default setting allows. Definition: Specifies the number of raster sweeps the scanner will execute on PDF symbols before decoding. A value of 0 effectively disables this feature, which allows the decoder to make a best guess as to when enough symbol words have been captured. Serial Cmd: <K476,status,raster sweeps before decode attempt,fixed symbol length status,fixed symbol length,decode at end of read> Default: 0 (disabled) Options: 0 to MS-890 Industrial Automation Scanner User Manual

117 Symbologies Fixed Symbol Length Status (PDF417) Usage: Definition: Serial Cmd: Default: Options: Used to increase data integrity by ensuring that only one symbol length will be accepted. When enabled, the PDF symbol must contain the same number of characters as the symbol length setting before it can be considered a good decode. The scanner will ignore any symbol not having the specified length. <K476,status,raster sweeps before decode attempt,fixed symbol length status,fixed symbol length,decode at end of read> Disabled 0 = Disabled 1 = Enabled Fixed Symbol Length (PDF417) Definition: Specifies the exact number of characters the scanner will recognize. Serial Cmd: <K476,status,raster sweeps before decode attempt,fixed symbol length status, fixed symbol length,decode at end of read> Default: 10 Options: 1 to 2710 Note: Fixed Symbol Length Status must be enabled for Fixed Symbol Length to take effect. Decode at End of Read (PDF417) Definition: Serial Cmd: Default: Options: Allows the user to specify that the decoding of the PDF417 symbol take place after the requirements of End of Read Cycle have been satisfied. This means that the scanner will accumulate information about the PDF417 candidate symbol but will not attempt to error-correct or translate the information until the end of the read cycle. <K476,status,raster sweeps before decode attempt,fixed symbol length status, fixed symbol length,decode at end of read> Disabled 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 5-23

118 Narrow Margins/Symbology ID Narrow Margins/Symbology ID Usage: Definition: Serial Cmd: Default: Used when the leading and trailing edges of the symbols are smaller than the standard margin or when other objects encroach into the margins. Allows the scanner to read symbols with quiet zones less than 8 times the width of the narrow bar element. The quiet zone is the space at the leading and trailing ends of a symbol. Each quiet zone can be as narrow as only five times the width of the narrow bar element when Narrow Margins is enabled. <K450,narrow margins status,symbology identifier status> Disabled Options: 0 = Disabled 1 = Enabled Note: Do not use Narrow Margins with Large Intercharacter Gap enabled in Code 39 or Codabar. Symbology ID Usage: Definition: Serial Cmd: Default: Used when the symbology type and how it s decoded needs to be known. Symbology ID is an AIM standard prefix set of characters that identify the symbol type. When enabled, the scanner analyzes and identifies the symbology and adds a three character identifying prefix to the data: 1. ] (close bracket character) indicating the presence of a symbology ID 2. A, C, E, I, L, Q, b, d, p, P, M A = Code 39, C = Code 128 or EAN-128, E = UPC/EAN, I = I 2/5, F = Codabar; G = Code 93, L = PDF417, a = Pharmacode, e = Composite/RSS, L = PDF417 and Micro PDF Modifier (see Explanation of Modifiers below) <K450,narrow margins,symbology identifier status> Disabled Options: 0 = Disabled 1 = Enabled 5-24 MS-890 Industrial Automation Scanner User Manual

119 Symbologies Explanation of Modifiers for Code 39, Codabar, and Interleaved 2/5 For Code 39, Codabar and I 2/5, the modifier indicates Check Character and Check Character Output Status. For Code 39 only, Full ASCII needs to be enabled to see modifiers 4, 5, and 7. Modifier Check Character Check Character Output Example:]A5 indicates a Code 39 symbol with Check Character and Check Character Output Status enabled and Full ASCII conversion performed. Explanation of Modifiers for Other Symbologies For Code 128, a 1 indicates EAN-128; otherwise the modifier is a 0. For all other codes, the modifier is 0. Full ASCII conversion performed (Code 39 only) 0 Disabled N/A No 1 Enabled Enabled No 3 Enabled Disabled No 4 Disabled N/A Yes 5 Enabled Enabled Yes 7 Enabled Disabled Yes MS-890 Industrial Automation Scanner User Manual 5-25

120 Background Color Background Color Usage: Definition: Serial Cmd: Default: If the background is darker than the symbol, then enable black background. Typically the background is white; but on PCBs for example, they can be black. Allows the user to choose which symbol background (white or black) the scanner can read. <K451,background color> White Options: 0 = White 1 = Black 5-26 MS-890 Industrial Automation Scanner User Manual

121 Autodiscriminate Symbologies Although Autodiscriminate is not a configuration command, but it is included here as a convenient tool for enabling most symbol types. Usage: Definition: Serial Cmd: Default: Options: Commonly used for quick setup mode to detect symbol type. This is particularly useful for users who might be unfamiliar with their application s symbology. Note: It does not alter individual fields such as Start/Stop, Fixed Length, etc. These need to be setup individually. Enables all available symbology types except PDF417, UPC/EAN, and Pharmacode. The user may also individually disable/enable each symbology type. <P> Code 39 (only) <P> Enables all codes except noted above. <Q> Enables Code 39 only <R> Enables Codabar only <S> Enables I 2/5 only Note: If using an I 2/5 symbol, verify that the number of characters in the symbol being scanned matches the symbol length enabled for the I 2/5 symbol type (default is 10 and 6). MS-890 Industrial Automation Scanner User Manual 5-27

122 Autodiscriminate 5-28 MS-890 Industrial Automation Scanner User Manual

123 6 I/O Parameters Contents I/O Parameters by ESP I/O Parameters Serial Commands Symbol Data Output No Read Message Bad Symbol Message No Symbol Message Read Duration Output Output Indicators Beeper Serial Verification EZ Button EZ Button Modes Input Configurable Output Trend Analysis Output Diagnostics Output Configurable Output Trend Analysis Output Diagnostics Output Configurable Output Trend Analysis Output Diagnostics Output Database Identifier Output Quality Output This section includes instructions on setting up conditions for changing input/output electrical transitions for control of the scanner s internal and external devices. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. MS-890 Industrial Automation Scanner User Manual 6-1

124 I/O Parameters by ESP I/O Parameters by ESP Click this button to bring up the I/O Parameters menu. To open nested options, single-click the +. To change a setting, double-click the setting and use your cursor to scroll through the options. 6-2 MS-890 Industrial Automation Scanner User Manual

125 I/O Parameters Serial Commands I/O Parameters Command Title Command Format Serial Verification <K701,serial command echo status,serial command beep status, control/hex output> Beeper <K702,status> Quality Output <K704,quality output separator,reads/trigger status,direction output> Symbol Data Output <K705,status,when to output> Read Duration Output <K706,status,separator> No Read Message <K714,status,message> Bad Symbol Message <K715,status,bad symbol message> No Symbol Message <K716,status,no symbol message> Input 1 <K730,mode,active state> Target/Flood LEDs <K750,green flash LED status,green flash duration> Database Identifier Output <K759,status,separator> EZ Button <K770,global mode,default on power-on status> EZ Button Modes <K771,one beep,two beeps,three beeps> Trend Analysis Output 1 <K780,trend analysis mode,number of triggers,number to output on,decodes/trigger threshold> Trend Analysis Output 2 <K781,trend analysis mode,number of triggers,number to output on,decodes/trigger threshold> Trend Analysis Output 3 <K782,trend analysis mode,number of triggers,number to output on,decodes/trigger threshold> Diagnostic Output 1 <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Diagnostic Output 2 <K791,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Diagnostic Output 3 <K792,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Configurable Output 1 <K810,output on,output state,pulse width,output mode> Configurable Output 2 <K811,output on,output state,pulse width,output mode> Configurable Output 3 <K812,output on,output state,pulse width,output mode> MS-890 Industrial Automation Scanner User Manual 6-3

126 Symbol Data Output Symbol Data Output Usage: Definition: Symbol Data Output Mode Serial Cmd: Default: Options: Disabled Usage: Definition: Match Usage: Definition: Mismatch Usage: Definition: Good Read Usage: Definition: Useful when the host needs symbol data only under certain conditions. Defines the conditions under which decoded symbols are transmitted to the host. <K705,output status,when to output> Good Read 0 = Disabled 1 = Match 2 = Mismatch 3 = Good Read Disabled is useful when an application only needs to use the discrete outputs and can allow the scanner to do the decision-making. When set to Disabled, the host does not need the symbol data and the communication lines are used only for setup and status checks. When set to Disabled, the scanner will not transmit any data that is generated during a read cycle (symbols, No Reads, etc.). Match is typically used to route items with the same identifying data to the same location. With Match enabled, the scanner transmits symbol data whenever the symbol data information matches the master symbol. Mismatch is typically used as a flag within the host system to prevent an item from being routed in the wrong container. With Mismatch enabled, the scanner transmits symbol data whenever the symbol data information does NOT match the master symbol. Note: A No Read can still be transmitted if enabled. Good Read is used when an application requires all symbol data to be transmitted. It s typically used in tracking applications in which each object is uniquely identified. With Good Read enabled, the scanner transmits symbol data on any good read regardless of Matchcode Type setting. Note: A No Read can still be transmitted if enabled. 6-4 MS-890 Industrial Automation Scanner User Manual

127 When to Output Symbol Data I/O Parameters Definition: Serial Cmd: Default: This command allows the user to choose when symbol data can be sent to the host. <K705,symbol output status,when to output> As Soon As Possible Options: 0 = As Soon As Possible 1 = End of Read Cycle As Soon As Possible Usage: Definition: As Soon As Possible is useful in applications in which symbol data needs to be moved quickly to the host, typically when the host is making decisions based on symbol data. Enabling As Soon As Possible causes symbol data to be sent to the host immediately after a symbol has been successfully decoded. Note: More than one decode might in fact be required to qualify as a good decode, depending on how Decodes Before Output is set. End of Read Cycle Note: See End of Read Cycle Mode on page 4-14 for options to end the read cycle. Usage: Definition: End of Read Cycle is useful in timing-based systems in which the host is not ready to accept data at the time it is decoded. Enabling End of Read Cycle means that symbol data does not get sent to the host until the read cycle ends with a timeout or new trigger. Start of read cycle End of read cycle Read Cycle Timeout Host activates trigger Host expects output Read Cycle MS-890 Industrial Automation Scanner User Manual 6-5

128 No Read Message No Read Message Usage: Definition: Used in applications where the host needs serial verification that a symbol has not been read and especially useful in new print verification. When enabled, and if no symbol has been decoded before timeout or the end of the read cycle, the No Read message will be transmitted to the host. No Read Status Serial Cmd: Default: <K714,status,message> Enabled Options: 0 = Disabled 1 = Enabled No Read Message Definition: Serial Cmd: Default: Any combination of ASCII characters can be defined as the No Read message. <K714,status,message> NOREAD Options: 1 to 128 ASCII characters. Note: No Read Message will only be transmitted if Symbol Output is set to Match, Mismatch or Good Read. No Read Message can be set to any ASCII characters except NUL, <, >, and,. 6-6 MS-890 Industrial Automation Scanner User Manual

129 Bad Symbol Message I/O Parameters Usage: Definition: Serial Cmd: Default: Options: Useful in determining if a symbol is present and if user defined requirements for that symbol are met. Can tell the user if a qualified symbol is present but not decodable. Sets the requirements that will qualify an object or a symbol before outputting a decode or message. When enabled, sends a message to the host whenever an object meets the qualifications setup but is not decoded. <K715,[unused],message> BAD_SYMBOL 1 to 128 ASCII characters No Symbol Message Usage: Definition: Serial Cmd: Default: Options: Useful in determining if a symbol is present and if user defined requirements for that symbol are met. Can tell the user if an object does not qualify as a symbol. Sets the requirements that will qualify an object or a symbol before outputting a decode or message. When enabled, sends a message to the host whenever an object meets the qualifications setup but is not decoded. <K716,[unused],message> NO_SYMBOL 1 to 128 ASCII characters MS-890 Industrial Automation Scanner User Manual 6-7

130 Read Duration Output Read Duration Output Usage: Definition: Useful in evaluating actual read cycle timing results, especially when initially setting up an application to determine maximum line speed (obtainable based on spacing between symbols.) When enabled the duration of the read cycle (in milliseconds) is appended to the symbol data. The read duration is the time from the beginning of the read cycle until data is output. Read Duration Output Mode Serial Cmd: <K706,status,separator> Default: Disabled Options: 0 = Disabled 1 = Enabled Important: To measure the entire read cycle when in External Level trigger mode, set When to Output Symbol Data to End of Read Cycle. This output can measure over 49 days worth of duration; if exceeded, the OVERFLOW message will be output in place of the duration. Read Duration Output Separator Definition: Serial Cmd: Default: Options: User defined character that separates the symbol information from the Read Duration Output. <K706,status,separator>, (comma) Any ASCII character. 6-8 MS-890 Industrial Automation Scanner User Manual

131 Output Indicators I/O Parameters Note: System features such as autocalibration and EZ Button setup may illuminate scanner LEDs regardless of parameter settings. Green Flash Mode Usage: Definition: Serial Cmd: Default: Options: Used as a visual verification that a Good Read has occurred. An array of green LEDs in the front of the scanner can be programmed to flash in response to user-defined conditions. <K750,green flash LED status,green flash duration> Good Read 0 = Disabled 1 = Good Read 2 = Static Presentation 3 = Match 4 = Mismatch Disabled Green flash LEDs are disabled. Good Read Green flash LEDs will flash when a Good Read condition is met or when Matchcode is enabled and a match occurs. Static Presentation Mode Static Presentation Mode is used in conjunction with Continuous Read Mode: <K200,0>. When operating in Static Presentation Mode, the red LEDs will illuminate while the scanner is searching for a symbol in Continuous Read Mode. When a symbol is placed in the field of view and a Good Read occurs, the green LEDs will illuminate and stay on for the duration of time set in Green Flash Duration. Only one read will occur during that time unless more than one symbol is enabled in Number of Symbols. Note: If Static Presentation Mode is selected but the scanner is not in Continuous Read, the Green Flash will not occur. To use Static Presentation: 1. Enable Continuous Read. 2. Select the number of symbols. 3. Enable Static Presentation in Green Flash Mode. 4. Select the read time in Green Flash Duration. MS-890 Industrial Automation Scanner User Manual 6-9

132 Output Indicators Match The green LEDs will flash when a match condition is met. If multisymbol is enabled, then green flash LEDs will illuminate only if all symbols qualify as a match. If matchcode is disabled, then this mode will activate the LEDs on a Good Read. Mismatch Same as Match, except that LEDs will illuminate on a mismatch MS-890 Industrial Automation Scanner User Manual

133 I/O Parameters Green Flash Duration Usage: Definition: Serial Cmd: Default: Options: Provides visual verification that a Good Read has occurred. When a Good Read occurs, the green LEDs will illuminate and stay on for the time set in the Green Flash Duration value. <K750,green flash mode,green flash duration> 100 (1 second) 0 to (in 10 ms increments) MS-890 Industrial Automation Scanner User Manual 6-11

134 Beeper Beeper Usage: Definition: Can be used as an audible verification that either a good read or a No Read has occurred. A beep is emitted either after each good read of a symbol or after each No Read. Note: Beeper will also sound if any of the following occur: The scanner is defaulted. A send/save command from ESP or an Exit command from any embedded menu. A <Z>, <Zp>, <Zd>, or <K701,,1> command is sent. Beeper Status Serial Cmd: Default: Options: <K702,status> On Good Read 0 = Disabled 1 = On Good Read 2 = On No Read 6-12 MS-890 Industrial Automation Scanner User Manual

135 Serial Verification I/O Parameters Usage: Definition: These commands are useful in removing any doubt about the scanner s acceptance and response to host configuration commands. For example, if the current preamble is SOM and <Kd1, START> is entered, the scanner will echo back <Kd1, SOM> since the attempted entry START exceeds the four character limit for that command. Therefore it is rejected and the existing SOM message is echoed back and remains the preamble message. Allows the user to verify configuration command status. Serial Command Echo Status Important Note: ESP will not function whenever this command is enabled. Definition: When enabled, a configuration command received from the host is echoed back to the host with the resultant settings. Host Scanner Function: Serial Cmd: Default: If a command with multiple fields is processed, some of the fields may have been processed properly while others were not. The changes will appear in the string echoed back so that the user will know which fields did or did not change. <K701,serial command echo status,serial command beep status,control/ hex output> Disabled Options: 0 = Disabled 1 = Enabled Serial Command Beep Status Important: ESP will not function whenever this command is enabled. Usage: Definition: Function: Serial Cmd: Default: Used to audibly verify the acceptance and validity of a command. Causes the scanner to beep once whenever a K command is entered to indicate that the command was accepted and processed. If an invalid command is entered, the scanner beeps 5 times to indicate an invalid entry. However, this does not necessarily mean that all data fields have been entered incorrectly. Only one bad field needs to be found in order to activate the 5 beep response. <K701,serial command echo status,serial command beep status,control/ hex output> Disabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 6-13

136 Serial Verification Control/Hex Output Usage: Definition: Serial Cmd: Default: Useful for viewing settings with binary characters when using serial command on a terminal. Determines the response to a Serial Command Echo or status request command. When set to Control, two characters are transmitted to represent a non-displayable character. For example, a carriage return will be shown as the two characters: ^M. When set to Hex, the output is the hex character. <K701,serial command echo status,serial command beep status,control/ hex output> Control Options: 0 = Control 1 = Hex 6-14 MS-890 Industrial Automation Scanner User Manual

137 EZ Button I/O Parameters The EZ Button has four positions, selectable by the length of time the button is held down, and indicated by one, two, three, and four beeps in succession. Each position can be programmed for any of eight options. Definition: Serves as a master switch to enable/disable the EZ Button status. Serial Cmd: <K770,global status,default on power-on,load configuration database, save for power-on> Default: Enabled Options: 0 = Disabled 1 = Enabled 2 = Trigger 3 = Unlatch Outputs 4 = Parameter Switch Global Status Disabled When set to Disabled, the EZ Button does not function. Enabled When selected, the EZ Button is enabled and the function of each button position is selected by the EZ Button Mode command. Trigger When selected, the EZ Button acts as a trigger for the scanner to start and end read cycles. All other button operations are inactive. In External Level: In External Edge: The read cycle endures for as long as the EZ Button is pressed, unless a timeout occurs and Timeout is enabled for End of Read Cycle. As with Level, Edge allows a read cycle to be initiated by pressing the EZ Button, but unlike Level, the read cycle ends with a Good Read output, a timeout, or a new trigger. Unlatch Outputs In this configuration, the EZ Button will unlatch any logic outputs that have been latched. Parameter Switch The parameter switch toggles between custom defaults and power-on settings. The condition is the same as that achieved by sending the <Arc> and <Arp> commands consecutively. MS-890 Industrial Automation Scanner User Manual 6-15

138 EZ Button Default on Power-On Definition: When enabled, if the EZ Button is held down on power-on the scanner will default and save for power-on. Serial Cmd: <K770,global status,default on power-on,load configuration database, save for power-on> Default: Enabled Options: 0 = Disabled 1 = Enabled Load Configuration Database Definition: Allows the user to load the Configuration Database with calibration results. When the user performs a calibration using the EZ Button, all the database entries are moved down one index and the results of the calibration are saved to index 1. The results will be saved as current settings as well. Serial Cmd: <K770,global status,default on power-on,load configuration database, save for power-on> Default: Enabled Options: 0 = Disabled 1 = Enabled Save for Power-On Definition: If enabled, after calibration is complete, all parameters will be saved for power-on. Serial Cmd: <K770,global status,default on power-on,load configuration database, save for power-on> Default: Disabled Options: 0 = Disabled 1 = Enabled 6-16 MS-890 Industrial Automation Scanner User Manual

139 EZ Button Modes I/O Parameters Usage: Definition: Serial Cmd: Options: Useful for performing multiple, repetitive tasks at the work site. Allows the user to program each of the EZ Button s 3 positions from a selection of 10 modes. <K771,single beep,two beeps,three beeps> Single Beep Two Beeps Three Beeps 0 = Disabled 0 = Disabled 0 = Disabled 1 = Read Rate 1 = Read Rate 1 = Read Rate 2 = Calibration 2 = Calibration 2 = Calibration 3 = Save for Power-On 3 = Save for Power-On 3 = Save for Power-On 5 = Load New Master 5 = Load New Master 5 = Load New Master 9 = Bar Code Configuration 9 = Bar Code Configuration 9 = Bar Code Configuration Disabled When set to disabled, the associated button position will have no function associated with it, and the position will be skipped over. Read Rate Read Rate will be initiated when the associated button position is selected. Read Rate will perform decodes/second and is the same as sending a <C> from the terminal. To exit Read Rate Mode quickly press and release the EZ Button. Calibration Calibration will be initiated when the associated button position is selected. To abort calibration, quickly press and release the EZ Button. Save for Power-On All scanner settings will be saved to non-volatile memory to be recalled on power-on whenever the associated button position is selected. This is the same as sending a <Z> from the terminal. Load New Master Functions in the same way as new master pin input whenever the associated button position is selected. The new master pin s Consecutive Decode requirement holds true for this function. Bar Code Configuration Enables Bar Code Configuration mode whenever the associated button position is selected. When enabled, the scanner can accept configuration commands from symbols. To disable, quickly press and release the EZ Button. MS-890 Industrial Automation Scanner User Manual 6-17

140 EZ Button Modes EZ Button Operation Single Beep (Position #1) Hold down button until a single beep is heard. Two Beeps (Position #2) Hold down button until two quick beeps are heard. Three Beeps (Position #3) Hold down button until three quick beeps are heard MS-890 Industrial Automation Scanner User Manual

141 Input 1 Definition: Usage: I/O Parameters A programmable, discrete input used to reset counters, outputs or control optoelectrical settings. For example, an application is setup so that a mismatch stops the production line by using outputs in a latch mode. A push-button switch can be connected to the input pin so that when pressed, it unlatches the output, allowing the line to resume operations. Input Mode Definition: Serial Cmd: Default: Options: Determines the functionality of the input. <K730,input mode,active state> Disabled 0 = Disabled 1 = Reset Counts 2 = Unlatch Output Disabled Definition: When set to Disabled, there is no effect on operation. Reset Counts Usage: Definition: Primarily used in test mode. Can also be used to reset counters daily. When set to Reset Counts, a transition to the active state of the input will cause the scanner to reset the internal counters (See Counters on page 12-6). Unlatch Output Definition: This setting is used in combination with any of the three discrete outputs that are in Unlatch Mode 1. A transition to the active state will clear any of the three outputs that were previously latched. Active State Definition: Serial Cmd: Default: Determines the function of the input pin. <K730,input mode,active state> Active Closed Options: 0 = Active Open 1 = Active Closed Note: If set to Match or Mismatch, Symbol Data Output Status will not take effect unless Matchcode Type is enabled and a master symbol is loaded into memory. MS-890 Industrial Automation Scanner User Manual 6-19

142 Configurable Output 1 Configurable Output 1 Output On Usage: Definition: Serial Cmd: Default: Options: This option provides discrete signalling to host software to control external devices such as PLCs and relays. It is useful for routing, sorting, and to prevent mis-packaging and mis-routing. Sets the discrete output functions for specific user-selected conditions. Allows the user to set the conditions under which an output (or outputs) will be activated. <K810,output on,output state,pulse width,output mode> Mismatch or No Read 0 = Mismatch or No Read 1 = Match or Good Read 2 = Mismatch 3 = No Read 4 = Trend Analysis 5 = [reserved] 6 = Diagnostic Warning 7 = In Read Cycle Note: If Output On is set to any mode containing Match or Mismatch, the transition (switching) will only occur if Matchcode Type is enabled and Master Symbol(s) are loaded into memory. Mismatch or No Read Activates a discrete output when the data does not match that of the master symbol or the symbol has not been decoded before the end of the read cycle. Match or Good Read Activates a discrete output when the symbol data matches the master symbol. Mismatch Activates a discrete output whenever the symbol data does not match that of the master symbol. No Read Activates a discrete output whenever the symbol data is not decoded before the end of the read cycle MS-890 Industrial Automation Scanner User Manual

143 I/O Parameters Trend Analysis Activates discrete output when a trend analysis condition is met, depending on the trend analysis option enabled. Typically used when successful decodes are occurring but a discrete output is needed to flag a trend in quality issues. Diagnostic Warning Activates discrete output when a diagnostic warning condition is met, depending on the diagnostic option enabled. Typically used when a discrete indication of a diagnostic condition is needed. In Read Cycle Activates a discrete output when the scanner is in a read cycle. MS-890 Industrial Automation Scanner User Manual 6-21

144 Configurable Output 1 Output State Definition: Sets the active electrical state of the discrete output. Serial Cmd: <K810,output on,output state,pulse width,output mode> Default: Negative Options: 0 = Negative 1 = Positive Pulse Width Definition: Sets the time in 10 ms increments that the discrete output remains active. Serial Cmd: <K810,output on,output state,pulse width,output mode> Default: 50 Options: 1 to (Divide the number entered on the command line by 100 for time in seconds) Output Mode Definition: Serial Cmd: Default: Options: Sets the condition in which the discrete output is de-activated. <K810,output on,output state,pulse width,output mode> Pulse 0 = Pulse 1 = Latch Mode 1 2 = Latch Mode 2 3 = Latch Mode 3 Pulse This is the default mode of operation in which the programmable output is activated when the Output On condition has been met and held active for the duration of the selected pulse width. Latch Mode 1 (Unlatch on Input 1 Pin) In this mode the programmable output will be activated when the Output On condition is met. It will stay active until the state of the Input 1 pin changes from inactive to active or the proper mode is configured using the EZ Button. Important: To unlatch using the Input 1 pin, the input status must be set to Unlatch Outputs. To unlatch using the EZ Button, the button status must be set to Unlatch Mode. Latch Mode 2 (Unlatch Opposite Condition) The programmable output is activated when the Output On condition has been met and held active until the opposite condition selected under Output On has been met. For example, if No Read is enabled under Output On, the programmable output will go active on a No Read and remain active until the opposite condition, a Good Read, occurs MS-890 Industrial Automation Scanner User Manual

145 I/O Parameters Latch Mode 3 (Unlatch Re-Enter Read Cycle) The programmable output is active when the Output On condition has been met and is held active until a new read cycle begins. Note: All of the Output On modes are inhibited when any Output on Warning is active for Output 1. MS-890 Industrial Automation Scanner User Manual 6-23

146 Configurable Output 1 Trend Analysis Output 1 Note: Output On in Output 1 Parameters must be set to Trend Analysis for this output to function. Usage: Useful in cases where the user doesn t want to shut down for one condition but wants to monitor quality and read conditions. Definition: Applies Trend Analysis settings to Output 1. With Trend Analysis, the user can track the occurrences and frequency of mismatches, No Reads, and the number of reads per trigger, and output the results to any of three outputs. Example: Trend Analysis Mode = No Read Number of Triggers = 25 triggers (read cycles) Number to Output On = 4 Decodes per Trigger = 1 In this example, the scanner will activate an output when 4 No Reads occur within a period of 25 triggers (read cycles), at 1 decode per trigger MS-890 Industrial Automation Scanner User Manual

147 I/O Parameters Trend Analysis Mode Definition: Serial Cmd: Default: Options: Sets the trend condition (Mismatch, No Read, Decodes/Trigger, Bad Symbol, or No Symbol) that will activate the output. <K780,trend analysis mode,number of triggers,number to output on, decodes/trigger threshold> No Read 0 = Mismatch 1 = No Read 2 = Decodes/Trigger Threshold 3 = Bad Symbol 4 = No Symbol Mismatch Output will be activated when the number of mismatches equals the value entered for Number to Output On within the trigger window selected in Number of Triggers. No Read Output will be activated when the number of No Reads equals the value entered for Number to Output On within the trigger window selected in Number of Triggers. Decodes/Trigger Threshold Output will be activated when the number of decodes equals the value entered for Number to Output On within the trigger window selected in Number of Triggers. Bad Symbol Output will be activated when the number of Bad Symbol occurrences equals the value entered for Number to Output On within the trigger window selected in Number of Triggers. No Symbol Output will be activated when the number of No Symbol occurrences equals the value entered for Number to Output On within the trigger window selected in Number of Triggers. MS-890 Industrial Automation Scanner User Manual 6-25

148 Configurable Output 1 Number of Triggers Definition: Serial Cmd: Default: 0 Options: 0 to 255 The number of triggers to examine for the trend analysis condition. <K780,trend analysis mode,number of triggers,number to output on, decodes/trigger threshold> Number to Output On Usage: Example: If Number to Output On is set to 3 and Trend Analysis Mode is set to No Read, then the output will not be activated until 3 No Reads have occurred. Definition: Sets the number of Trend Analysis Mode events (mismatches, No Reads, or reads/trigger as configured by Trend Analysis Mode) to occur within the trigger evaluation period before activating the associated output. Serial Cmd: <K780,trend analysis mode,number of triggers,number to output on, decodes/trigger threshold> Default: 0 Options: 0 to 255 Decodes/Trigger Threshold Definition: When set to this mode, and when the appropriate output is set to output on trend analysis, the scanner will function in a Decodes per Trigger mode during the read cycle and the trend analysis operation. Output will be activated based on whether or not the symbol decode count at the end of the read cycle crosses the decodes per trigger threshold. Note: Although this setup causes the scanner to function in a Decodes per Trigger mode, the decode count will only be appended to the symbol data if the status of the Decodes per Trigger command is enabled. Serial Cmd: <K780,trend analysis mode,number of triggers,number to output on, decodes/trigger threshold> Default: 0 Options: 0 to MS-890 Industrial Automation Scanner User Manual

149 Diagnostics Output 1 I/O Parameters Note: Output On in Output 1 Parameters must be set to Diagnostic Warning for this output to function. Over Temperature Serial Cmd: <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Default: 0 Options: 0 = Disabled 1 = Enabled Service Threshold Serial Cmd: <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Default: 0 Options: 0 = Disabled 1 = Enabled Laser Current High Serial Cmd: <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Default: 0 Options: 0 = Disabled 1 = Enabled Laser Current Low Serial Cmd: <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Default: 0 Options: 0 = Disabled 1 = Enabled Low Temperature Serial Cmd: <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> Default: 0 Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 6-27

150 Configurable Output 2 Configurable Output 2 Note: Output 2 has the same parameters and default settings as Output 1. Serial Cmd: Trend Analysis Output 2 Note: Output On under Output 2 Parameters must be set to Trend Analysis for this output to function. Serial Cmd: <K811,output on,output state,pulse width,output mode> Diagnostics Output 2 Note: Output On under Output 2 Parameters must be set to Diagnostic Warning for this output to function. Serial Cmd: <K781,trend analysis mode,trigger evaluation period,number to output on,decodes/trigger threshold> <K791,over temperature,service threshold,unused,laser current high,laser current low,low temperature> 6-28 MS-890 Industrial Automation Scanner User Manual

151 I/O Parameters Configurable Output 3 Note: Output 3 has the same parameters and default settings as Output 1 and Output 2. Serial Cmd: Trend Analysis Output 3 Note: Output On under Output 3 Parameters must be set to Trend Analysis for this output to function. Serial Cmd: <K812,output on,output state,pulse width,output mode> Diagnostics Output 3 Note: Output On under Output 3 Parameters must be set to Diagnostic Warning for this output to function. Serial Cmd: <K782,trend analysis mode,trigger evaluation period,number to output on,decodes/trigger threshold> <K792,over temperature,service threshold,unused,laser current high,laser current low,low temperature> MS-890 Industrial Automation Scanner User Manual 6-29

152 Database Identifier Output Database Identifier Output Usage: Useful in keeping track of which database entries read which symbols. Serial Cmd: <K759,status,separator> Default: 0 Options: 0 = Disabled 1 = Enabled Output Status Disabled When this command is disabled, no database identifier information will be output. Enabled When this command is enabled, the scanner will append a two-digit number and the characters DB to the data output following the separator for each symbol decoded using Configuration Database. For example, if the separator is an underscore character and the second database entry reads a symbol encoded with data capture during the read cycle, the symbol data output will be data capture_db02. If the database is not active, no identifiers will be attached to output. Separator Usage: Serial Cmd: Default: Options: The separator character separates the symbol data from the database identifier. <K759,status,separator> <space> Any ASCII character 6-30 MS-890 Industrial Automation Scanner User Manual

153 Quality Output I/O Parameters Definition: Usage: Allows the host to track the number of good reads per trigger by appending a five digit numeric field to the end of symbol data. When enabled, symbol data is followed by a separator, followed by the five digits in the form of For example, a certain symbol that has been averaging decodes per read cycle suddenly drops to 00012, this would be a good indication that a problem has arisen even though good reads are still occurring. Host system can monitor scanning performance (printing process, scanning environment changes, etc.) by setting thresholds in their processing or displaying the outputs for visual verification. Quality Output Separator Serial Cmd: Default: <K704,quality output separator,decodes/trigger status,direction output>, (comma) Options: Any ASCII character Note: For all serial configuration commands, the following characters cannot be used: NUL, <, >, and,. Decodes/Trigger Status Serial Cmd: Default: <K704,quality output separator,decodes/trigger status,direction output> Disabled Options: 0 = Disabled 1 = Enabled Direction Output Serial Cmd: Default: <K704,quality output separator,decodes/trigger status,direction output> Disabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 6-31

154 Quality Output 6-32 MS-890 Industrial Automation Scanner User Manual

155 7 Matchcode Contents Matchcode by ESP Matchcode Serial Commands Overview of Matchcode Using Master Symbols Matchcode Type Sequence Step New Master Pin Match Replace Mismatch Replace This section explains the Matchcode output functions and setup. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. MS-890 Industrial Automation Scanner User Manual 7-1

156 Matchcode by ESP Matchcode by ESP Click this button to bring up the Matchcode menu. To change a setting, double-click the setting and use your cursor to scroll through the options. To open nested options, single-click the +. Matchcode Serial Commands Command Title Matchcode Type Master Symbol Database Size New Master Pin Configuration Database Sequence Step Enter/Delete Master Symbol Data Request Master Symbol Data Match Replacement Message Mismatch Replacement Message Command Format <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> <K224,number of master symbols> <K225,status> <K227,database index,focus position,gain,tracking,agc mode,raster top,raster bottom,raster speed,laser framing status,laser on position, laser off position,laser power,background color> <K228,sequence step> <K231,master symbol number,master symbol data [no data will delete current master symbol data]> <K231,?>[for all] or <K231,master symbol number?> <K735,status,match replacement message> <K736,status,mismatch replacement message> 7-2 MS-890 Industrial Automation Scanner User Manual

157 Overview of Matchcode Matchcode Usage: Definition: Matchcode is used in applications to sort, route, or verify data based on matching the specific symbol in a variety of ways, as defined in this section. For example, a manufacturer might sort a product based on dates that are embedded in the symbol. With Matchcode you can store master symbol data in the scanner s memory, compare this data against the scanned symbols, and define how symbol data and/or discrete signal output will be directed. A master symbol database can be set up for up to 10 master symbols. MS-890 Industrial Automation Scanner User Manual 7-3

158 Using Master Symbols Using Master Symbols 1. Set Triggering Mode to External or Serial (see Trigger on page 4-5). 2. Set Matchcode Type to an option that fits your application (see Matchcode Type on page 7-5). 3. Define the output you want with your matchcode setup: a) Data output (Symbol Data Output on page 6-4). b) Discrete output (see Configurable Output 1 on page 6-20). 4. Select the number of master symbols you want to create. If more than one, send a <K224,number of master symbols> command (see Master Database on page 12-11). 5. Enter master symbol data in one of the following ways: a) Use ESP to type in master symbol data directly into the Utilities menu. b) Send a serial command with symbol data in the form of <Mmaster symbol#, data> (or <)data)> for single master symbol only). c) Send a <Gmaster symbol number> command to scan the next symbol as the master symbol. d) Enable the New Master Pin command and activate a discrete input to store the next symbol scanned as the master symbol (see New Master Pin on page 7-11). 7-4 MS-890 Industrial Automation Scanner User Manual

159 Matchcode Type Matchcode Note: When Matchcode is set to Enabled, Wild Card or Sequential, Number of Symbols will default back to 1 (if set to any number greater than 1). Definition: Serial Cmd: Default: Options: Disabled: Enabled: Sequential Matching: Wild Card: Allows the user to choose the way that master symbols will be compared with subsequently scanned symbols. Note: First set Triggering Mode to External or Serial. <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> Disabled 0 = Disabled 1 = Enabled 2 = Sequential 3 = Wild Card Has no effect on operations. Instructs the scanner to compare symbols or portions of symbols with the master symbol. Instructs the scanner to sequence after each match (numeric only) and compare symbols or portions of symbols for sequential numbers. Note: If Matchcode Type is set to Sequential, Number of Symbols will default back to 1 (if set to any number greater than 1). Allows the user to enter user defined wild card characters in the master symbol. Sequential Matching Usage: Definition: Serial Cmd: Default: Used in tracking product serial numbers that increment or decrement sequentially. With Sequential enabled under Matchcode Type, Sequential Matching determines if a count is in ascending (incremental) or descending (decremental) order. <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> Increment Options: 0 = Increment 1 = Decrement MS-890 Industrial Automation Scanner User Manual 7-5

160 Matchcode Type Match Start Position Usage: Definition: Function: Serial Cmd: Default: 0 Options: Match Length Match Start Position is useful in defining specific portions of a symbol for comparisons. For example, if a symbol contains a part number, manufacturing date, and lot code info but the user is only interested in the part number information, Match Start Position can be set to only sort on the part number and ignore the rest of the characters. Match Start Position determines the portions of symbols that will be matched by defining the first character in the symbol (from left to right) that will be compared with those of the master symbol, when Matchcode Type is set to Enabled or Sequential. For example, if Match Start Position is set to 3, the first 2 characters read in the symbol will be ignored and only the 3rd and subsequent characters to the right will be compared, up to the number of characters specified by Match Length. <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> 0 to maximum length allowed for master symbol Note: Match Start Position must be set to 1 or greater to enable this feature. A 0 setting will disable this feature. Definition: Defines the length of the character string that will be compared with that of the master symbol when Match Start Position is set to 1 or greater. When Match Start Position is set to 0, no comparison will occur. Usage: For example, if Match Length is set to 6 in a 10 character symbol, and Match Start Position is set for 2, only the 2nd through 7th characters (from left to right) will be compared. Serial Cmd: <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> Default: 1 Options: 1 to MS-890 Industrial Automation Scanner User Manual

161 Wild Card Character Matchcode Usage: Definition: Serial Cmd: Default: Options: For example, with Wild Card Character defined as the default asterisk, defining CR*34 as the master symbol will result in matches for CR134, CR234, but not CR2345. Entering the wild card at the end of the master symbol as in CR*** will result in matches for variable symbol lengths such as CR1, CR23, CR358, etc. provided that the number of wild card characters matches or exceeds the number of characters present. Wild Card Character allows a user to define a wild card character as part of the master symbol. <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> * (asterisk) Any valid ASCII character MS-890 Industrial Automation Scanner User Manual 7-7

162 Matchcode Type Sequence On No Read Usage: Definition: Serial Cmd: Default: Sequence On No Read is useful when the scanner needs to stay in sequence even if no decode occurs. When Sequence On No Read is Enabled and Matchcode is set to Sequential, the scanner sequences the master symbol on every match or No Read. When disabled, it does not sequence on a No Read. <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> Enabled Options: 0 = Disabled 1 = Enabled As an example of Sequence on No Read Enabled, consider the following series of decodes: Master symbol Decoded symbol Master symbol after decode No Read 004 (sequenced on No Read) No Read 006 (sequenced on No Read) 006 No Read 007 (sequenced on No Read) As an example of Sequence on No Read Disabled, consider the following series of decodes: Master symbol Decoded symbol Master symbol after decode No Read 003 (not sequenced) No Read 004 (not sequenced) 004 No Read 004 (not sequenced) MS-890 Industrial Automation Scanner User Manual

163 Sequence On Mismatch Note: Matchcode must be set to Sequential for this command to function. Matchcode Usage: Definition: Serial Cmd: Default: Enable this parameter if every trigger event should have a decode and more than one consecutive mismatch may occur. Disable this parameter if every trigger event should have a decode but no more than one consecutive mismatch may occur. When set to Enabled, the master symbol sequences on every decode, match or mismatch. When set to Disabled, the master symbol will not sequence whenever consecutive mismatches occur. <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read,sequence on mismatch> Disabled Options: 0 = Disabled 1 = Enabled The scanner will sequence the master to one more/less than the decoded symbol. As an example of Sequence On Mismatch Enabled, consider the following decodes: Master symbol Decoded symbol Master symbol after decode abc 004 (sequenced on mismatch) def 006 (sequenced on mismatch) 006 ghi 007 (sequenced on mismatch) As an example of Sequence On Mismatch Disabled, consider the following decodes: Master symbol Decoded symbol Master symbol after decode abc 004 (sequenced because of previous match) def 005 (sequenced because of previous match) 005 ghi 005 (not sequenced because of previous mismatch) You can access Master Symbol operations from the Utilities menu. MS-890 Industrial Automation Scanner User Manual 7-9

164 Sequence Step Sequence Step Usage: Useful in applications in which it is desirable to count by intervals other than 1. Definition: Sequencing in Matchcode operations can occur in steps from 1 to 32,768. Sequencing performs like a mechanical counter by displaying positive integers and a specific number of digits after rollovers. For example, = 997 (not 3) and = 002 (not 1002). Serial Cmd: <K228,sequence step> Default: 1 Options: 1 to Note: See <K223> (Matchcode Type on page 7-5) for more information. As an example of Sequence Step, if Sequence Step is set to 3 and Sequential Matching is set to Increment. Master Symbol Decoded Symbol Master Symbol After Decode MS-890 Industrial Automation Scanner User Manual

165 New Master Pin Matchcode Usage: Definition: Serial Cmd: Default: Some applications require the line worker to change the master symbol. This can be done by installing a switch at the location of the scanner. It is very common to have a keyed switch so that accidental switching does not occur. After New Master Pin is enabled, a pulse can be received on the new master pin which will cause the scanner to record the next decoded symbol(s) as the new master symbol(s). It is important to note that the enabling New Master Pin does not in itself cause a master symbol to be recorded. The master pin must then be activated momentarily (for a minimum of 10 ms) before a master symbol can be scanned into memory. <K225,status> Disabled Options: 0 = Disabled 1 = Enabled After New Master Pin has been enabled and the pin activated, decodes will be saved in the master database beginning with master symbol #1. If the scanner is configured for a multisymbol read cycle (Number of Symbols is greater than 1), the remaining decodes will be saved in each consecutive master symbol location. For example, if Number of Symbols is set to 3 and New Master Pin is then activated, at the end of the next read cycle, the decoded symbols will be saved as master symbols 1, 2, and 3. MS-890 Industrial Automation Scanner User Manual 7-11

166 Match Replace Match Replace Usage: Provides a convenient shortcut for applications that need to output a predefined text string whenever a symbol matches a master symbol. Definition: Outputs a user-defined data string whenever a match occurs and Matchcode is enabled. Serial Cmd: <K735,status,replacement string> Default: Disabled Options: 0 = Disabled 1 = Enabled Replacement String Definition: Serial Cmd: Default: Options: User-defined data string that, when enabled, replaces symbol data whenever a match occurs. <K735,status,replacement string> MATCH 1 to 128 ASCII characters 7-12 MS-890 Industrial Automation Scanner User Manual

167 Mismatch Replace Matchcode Usage: Provides a convenient shortcut for applications that need to output a predefined text string whenever a symbol does not match a master symbol. Definition: Outputs a user-defined data string whenever a mismatch occurs and Matchcode is enabled. Serial Cmd: <K736,status,replacement string> Default: Disabled Options: 0 = Disabled 1 = Enabled Replacement String Definition: Serial Cmd: Default: Options: User-defined data string that, when enabled, replaces symbol data whenever a mismatch occurs. <K736,status,replacement string> MISMATCH 1 to 128 ASCII characters MS-890 Industrial Automation Scanner User Manual 7-13

168 Mismatch Replace 7-14 MS-890 Industrial Automation Scanner User Manual

169 8 Diagnostics Contents Diagnostics by ESP Diagnostics Serial Commands Counts Hours Since Last Reset Warning Messages Laser Current Warning Present Operating Temperature (Deg. C) High Temperature Threshold Low Temperature Threshold Lifetime Hours Service Message This section describes warning and operating messages and their settings. Important: Since Warning Messages and NOVRAM Messages are not enabled by default, these messages will not be displayed. However, if you suspect that erroneous defaults are occurring, enable Warning Messages and NOVRAM Messages by sending <K 400,1,,,1>. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. MS-890 Industrial Automation Scanner User Manual 8-1

170 Diagnostics by ESP Diagnostics by ESP Click this button to bring up the Diagnostics menu. To open nested options, single-click the +. To change a setting, double-click the setting and use your cursor to scroll through the options. Diagnostics Serial Commands Command Title Warning Message Status Lifetime Hours High Temperature Warning Low Temperature Warning Power-On/Resets Counts Hours Since Last Reset Present Operating Temperature Service Message Laser Current Warning Command Format <K400,warning message status,laser high status,laser low status, NOVRAM/reset warning status> <K401,hours x 10,message> <K402,status,message> <K403,status,message> <K406?> returns: <K406,power-ons,resets,parameter saves> (Read-Only) <K407?> returns: <K407,hours,minutes> (Read-Only) <K408?> returns: <K408,current operating temp.> (Read-Only) <K409,status,message,time,resolution> <K411,high current status,high current message,low current warning, low current message> 8-2 MS-890 Industrial Automation Scanner User Manual

171 Counts (This command is Read-Only.) Diagnostics Power-Ons Definition Serial Cmd: Read-Only Range: Returns the number of times the scanner has been re-powered or a watchdog reset occurs. Send: <K406?> Returns: <K406,power-ons,resets,parameter saves> 0 to power-ons. Resets Usage: Definition Serial Cmd: Read-Only Range: Used for detecting unwanted resets caused by power supply problems or ESD transients. Resets include watchdog reset, <A> and <Z> commands, and hardware defaults. A watchdog reset is a reset that is forced whenever the software locks up. Send: <K406?> Returns: <K406,power-ons,resets,parameter saves> 0 to resets. Parameter Saves Definition Serial Cmd: Read-Only Range: Returns the number of times parameters are written to memory, including <Z> commands and hardware defaults. Send: <K406?> Returns: <K406,power-ons,resets,parameter saves> 0 to saves. MS-890 Industrial Automation Scanner User Manual 8-3

172 Hours Since Last Reset Hours Since Last Reset (This command is Read-Only.) Usage: Definition: Serial Cmd: Read-Only Ranges: Used as a troubleshooting tool that can help pinpoint the cause of a reset. Records the number of hours and minutes of operation since the last system reset. Send: <K407?> Returns: <K407,hours,minutes> 0 to 255 hours, 0 to 59 minutes. 8-4 MS-890 Industrial Automation Scanner User Manual

173 Warning Messages Diagnostics Important Note: Warning Message Status must be enabled before any warnings in this menu can be displayed. Usage: Definition: Function: These messages serve as a flag to service a scanner or as an early warning that potential problems could arise. They are particularly useful in factories that run constantly and can t afford down time. Warning messages that relate to the environment and condition of the scanner can be defined and set to activate specific outputs. Note: When enabled, the error condition will override all other operational modes configured for the output.when enabled, laser current and NOVRAM warning messages will be transmitted to the host or any active port whenever the pre-defined conditions are met. When enabled, warning messages will be transmitted to the host or any active port. Note: This option must be enabled before any other warning messages can be transmitted. Warning Message Status Serial Cmd: Default: Options: <K400,warning message status,laser high status,laser low status, NOVRAM/reset warning status> Disabled 0 = Disabled 1 = Enabled Laser High Status When enabled, a message is transmitted whenever the laser current exceeds a factory-calibrated reference value which cannot be altered. The message repeats once every 30 minutes until the condition is corrected. Usage: Definition: Serial Cmd: Default: Alerts the user to impending laser failure. Enables the Laser High message. <K400,warning message status,laser high status,laser low status, NOVRAM/reset warning status> Enabled Options: 0 = Disabled 1 = Enabled MS-890 Industrial Automation Scanner User Manual 8-5

174 Warning Messages Laser Low Status When enabled, a message is transmitted whenever the laser current falls below a factory-calibrated reference value which cannot be altered. The message repeats once every 30 minutes until the condition is corrected. Usage: Definition: Serial Cmd: Default: Alerts the user to impending laser failure. Enables the Laser Low message. <K400,warning message status,laser high status,laser low status, NOVRAM/reset warning status> Enabled Options: 0 = Disabled 1 = Enabled NOVRAM/Reset Warning Status When enabled, a 7-character message is sent whenever the system detects a warning condition. Important: Warning Message Status must be enabled before the NOVRAM message in this menu can be transmitted. Usage: Alerts the user to NOVRAM failure. Serial Cmd: <K400,warning message status,laser high status,laser low status, NOVRAM/reset warning status> Default: Enabled Options: 0 = Disabled 1 = Enabled Note: If you suspect that erroneous defaults are occurring, enable NOVRAM Messages by sending <K400,1,,,1>. This will allow the NOVRAM messages, if present, to be viewed. Warning messages for NOVRAM can appear in one of four formats: <NVBAD-D> Indicates that diagnostic lifetime hours, power-on counts, and reset counts have been lost. The message repeats once every 30 minutes. <NVBAD-L> Indicates a problem with laser current factory reference. The message repeats once every 30 minutes. <DFALT-C> Indicates that NOVRAM settings have been defaulted either by a user-initiated default or by a problem with the scanner. This message is sent ONLY ONCE. <DFALT-F> Indicates that the factory NOVRAM settings have been defaulted. This message is sent ONLY ONCE upon reset. 8-6 MS-890 Industrial Automation Scanner User Manual

175 Laser Current Warning Alerts the user to impending laser failure. High Current Status Definition: Serial Cmd: Default: Options: High Current Message Definition: Serial Cmd: Default: Options: Low Current Status Definition: Serial Cmd: Default: Options: Low Current Message Definition: Serial Cmd: Default: Options: Diagnostics The High Current message is output whenever the laser current exceeds the factory-defined maximum. The message repeats once every 30 mimutes until the condition is eliminated. <K411,high current status,high current message,low current status,low current message> Disabled 0 = Disabled 1 = Enabled This message is output whenever the laser current exceeds the factory-defined maximum. <K411,high current status,high current message,low current status,low current message> HIGH_LASER Any ASCII string up to 10 characters. The Low Current message is output whenever the laser current exceeds the factory-defined minimum. The message repeats once every 30 mimutes until the condition is eliminated. <K411,high current status,high current message,low current status,low current message> Disabled 0 = Disabled 1 = Enabled This message is output whenever the laser current exceeds the factory-defined minimum. <K411,high current status,high current message,low current status,low current message> LOW_LASER Any ASCII string up to 10 characters. MS-890 Industrial Automation Scanner User Manual 8-7

176 Present Operating Temperature (Deg. C) Present Operating Temperature (Deg. C) (This command is Read-Only.) Usage: Definition: Serial Cmd: Used for setting Over Temperature Threshold and Under Temperature Threshold. Indicates temperature of the environment immediately outside of the scanner. A thermal sensor on the main PCB measures the internal temperature of the scanner. From this, a case-differential constant is subtracted to yield an estimated external temperature. Send: <K408?> Returns: <K408,current operating temp. (degrees C)> Note: When viewing the Present Operating Temperature, allow at least 20 minutes after startup for the scanner s inside and outside temperatures to stabilize. 8-8 MS-890 Industrial Automation Scanner User Manual

177 High Temperature Threshold Diagnostics A message can be defined that will display when a user-set High Temperature Threshold has been reached. The message repeats once every 30 minutes until the condition is corrected. This value is a reference to the external ambient temperature in the environment around the scanner. High Temperature Degrees Usage: Definition: Serial Cmd: Default: Options: Helps ensure that the scanner is being used within its temperature specification. Also, since hotter environments tend to shorten the life of electronics components, a user may want to set the temperature threshold closer to the nominal temperature of 25. A user can set a temperature value that when exceeded will cause a high temperature message to be displayed. If High Temperature Threshold is set to zero, then the warning message will be disabled. <K402,status,message> Disabled 0 = Disabled 1 = Enabled High Temperature Message Definition: The user can enter a message of up to 10-characters that will be displayed whenever High Temperature Threshold is exceeded. Serial Cmd: <K402,status,message> Default: HIGH_TEMP Options: Any 1 to 10 character ASCII string except NUL, <, or >. MS-890 Industrial Automation Scanner User Manual 8-9

178 Low Temperature Threshold Low Temperature Threshold Low Temperature Degrees Usage: Definition: Serial Cmd: Default: Options: Helps ensure that the scanner is being used within its temperature specification. The user can set a low temperature value that, whenever the ambient temperature falls below it, causes a low temperature message to be displayed. If Low Temperature Threshold is set to zero, the warning message will be disabled. <K403,status,message> Disabled 0 = Disabled 1 = Enabled Low Temperature Message Definition: The user can enter a message of up to 10-characters that will be displayed whenever the ambient temperature falls below the Low Temperature Threshold. Serial Cmd: <K403,status,message> Default: LOW_TEMP Options: Any 1 to 10 character ASCII string except NUL, <, or > MS-890 Industrial Automation Scanner User Manual

179 Lifetime Hours Diagnostics A message can be defined that will be transmitted whenever the scanner s elapsed time clock exceeds the set hours threshold. The message repeats one time every 30 minutes. Hours Threshold Usage: Used for setting up a preventive maintenance program. Definition: A user can set a time in hours that will cause a message to be sent whenever the scanner s run time exceeds this value. The elapsed time is the time the scanner is powered up. Serial Cmd: <K401,hours x 10,message> Default: 2500 (x 10 = 25,000 hours) Options: 0 to Note: Hours entered are 1/10 of the actual hours. Message Definition: The user can enter a message of up to 10-characters that will be displayed whenever the hours threshold is reached or exceeded. Serial Cmd: <K401,hours x 10,message> Default: SERVICE Options: Any 1 to 10 character ASCII string except NUL, <, or >. MS-890 Industrial Automation Scanner User Manual 8-11

180 Service Message Service Message When Service Message is enabled, a message of up to 10 ASCII characters is sent whenever the system detects that the service timer s limit has been reached. The service timer is reset at power-on, meaning that the service timer s limit is the amount of time since last reset. Service timer increments can be set in seconds or minutes. Serial Cmd: <K409,status,service message,threshold,resolution> Default: 0 Options: 0 = Disabled 1 = Enabled Service Message Serial Cmd: Default: Options: <K409,status,service message,threshold,resolution> SERVICE An ASCII string between 1 and 10 characters. Threshold Serial Cmd: <K409,status,service message,threshold,resolution> Default: 300 (5 minutes) Options: 1 to Resolution Serial Cmd: <K409,status,service message,threshold,resolution> Default: Seconds Options: 0 = Seconds 1 = Minutes 8-12 MS-890 Industrial Automation Scanner User Manual

181 9 Calibration Contents Calibration Serial Commands Calibration Steps Calibration Routine Calibration Results Configuration Database Optoelectric Control Advanced Calibration Features Calibration by Embedded Menu The purpose of calibration is to optimize the scanner s optical settings (focus, gain, and tracking) and scan speed to obtain the highest read rates in one or several symbol positions as required by the user s application. This section includes the overall steps in calibration and specific steps for calibration by ESP, serial command, and embedded menus. For most applications calibration is the only optical setup required. Changes to motor speed, focus, speed, gain, tracking, and AGC can also be made individually by manual command. Calibration Methods There are three ways to initiate calibration: ESP Calibration menu Serial command <@CAL> Embedded menu <@> Note: Calibration does not function with PDF417 symbols. However, you can substitute a Code 128 symbol with the same mil size as your PDF417. When you do this, enable Code 128 and disable Raster scanning. After calibration, switch back to PDF417 and Raster scanning. MS-890 Industrial Automation Scanner User Manual 9-1

182 Calibration Serial Commands Calibration Serial Commands Command Title Optoelectric Control Configuration Database Save Configuration Database Load Configuration Database Request Configuration Database Autocalibration Command Format <K226,mode,# active database settings,latch on trigger, timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> <K227,database index,focus position,gain,tracking,agc mode,raster top,raster bottom,raster speed,laser framing status,laser on position, laser off position,laser power, background color> <K227+,database index> <K227-,database index> <K227?,database index> or <K227?> for entire database. <K510,auto range,starting focus position,focus step size> 9-2 MS-890 Industrial Automation Scanner User Manual

183 Calibration Steps Calibration Follow this procedure for all three methods of calibration: 1. Position your symbol at the distance used in your application and confirm that it is at a distance within the specifications for that symbol size (see Position Scanner and Symbol on page 1-5). 2. If you are not certain of the code type, enable all code types by sending a <P> command from the terminal window, or clicking on the Autodiscrimination button in Calibration/ Advanced in ESP. 3. Start the calibration procedure. Note: Once a successful calibration is completed, you may want to save the setting to the calibration database (see Configuration Database on page 9-6). 4. Repeat calibration at other ranges and/or symbol types you might be scanning in your application. 5. Check your readings at each end of the scan width required for your application, keeping in mind that the scan width testing may not produce results that are entirely symmetrical. Note: If you are setting up for laser framing, be sure that you only test for calibration in the active areas of the scan beam. 6. To save the new settings (including focus, gain, and tracking) for power-on, use the Send/Recv button or send a <Zp> command. See Configuration Database on page 9-6 to learn how to setup a database using calibration or manually specified values. See Advanced Calibration Features on page 9-14 for ways to speed up and improve your calibration process. Note: To silence the beeper, send <K702,0> or remove or block the test symbol. MS-890 Industrial Automation Scanner User Manual 9-3

184 Calibration Routine Calibration Routine To calibrate gain, tracking, focus position, and scan speed automatically: 1. Click the Calibration button near the top of the screen. 2. Click the Calibrate button to start calibration. A Calibration in Progress... message will be displayed on your monitor along with the pass number and information on the focus position, gain, tracking and read rate. Allow some time for the scanner to cycle through the settings. Do not move or disturb the scanner or symbol while calibration is in progress. (It might take 2 to 3 minutes to complete.) 3. When completed, the settings that provided the highest read rate will be selected. You will see one of the following messages: Calibration Passed or Calibration Failed. If calibration passed, you will continue to see the read rate percentage and symbol data in the open pane below the data. Calibration by Serial Command To start the calibration process by serial command, send <@CAL> from ESP s Terminal. 9-4 MS-890 Industrial Automation Scanner User Manual

185 Calibration Results Calibration When a calibration command is sent, the scanner first steps through a coarse grid of focus settings, looking for readable symbols, and recording the highest read rates it encounters. This is Pass 1. During Pass 2, the scanner returns to the focus position where it found the best read rate and steps through a finer grid of focus, gain and tracking settings. The software evaluates the results and selects the best data. If calibration passes, a Calibration Passed message is displayed at the top of the window. To load the settings obtained from calibration into the Configuration Database: 1. Perform the calibration routine described in Calibration Routine on page Click on the Configuration Database tab. 3. Set Number of Active Database Settings and make your selection in Optoelectric Control in the menu tree to the left of the Database tab. 4. Click on an index to load standard settings. 5. Click Load Standard Settings to Database button. This will put Focus, Gain, and Tracking settings that resulted from calibration into the database index. 6. Repeat this procedure for other indexes. You can also enter individual values in any of the seven indexes by double-clicking anywhere on the index row and making changes in the popup text box. MS-890 Industrial Automation Scanner User Manual 9-5

186 Configuration Database Configuration Database Configuration Database by Serial Command Note: You can also set Focus, Gain Settings, Tracking Adjustment, Scan Speed, Laser Framing, and Background Color individually. Definition: Serial Cmd: The Configuration Database allows the user to save multiple scanner configuration settings. The database can be used to save the most commonly used configurations, making the scanner easily adaptable to changing applications, or it can be used in conjunction with Optoelectric Control, to change configurations dynamically. When Optoelectric Control is set to Control Trigger (Optoelectric Control Mode), the first seven indexes can be switched by external inputs. Each database configuration setting is assigned to a control trigger sequence. The table below illustrates the relationship between control trigger sequence and database indexes. Active Trigger(s) = 1, 2, 3 Active Trigger(s) = 1, 2 Active Trigger(s) = 1 Control Triggers Control Triggers Control Triggers Index N/A Disabled 1 1 Disabled Disabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 0 = Inactive Input State 1 = Active Input State <K227,database index,focus position,gain,tracking,agc mode,raster top,raster bottom,raster speed,laser framing status,laser on position,laser off position,laser power, background color> Important: Control Trigger 3 uses the External Trigger input. When this input is active, there is no external trigger available to the scanner. Therefore, when Control Trigger 3 is active and External Trigger Mode is selected, a read cycle will be triggered by an active input from any of the control trigger inputs. Since an active state on one of the control inputs is required to trigger a read cycle, sequence 000 would not be valid. When Control Trigger 3 is active, the sequence starts at 001. This allows a maximum of 7 accessible database settings. When Control Trigger 3 is not active, the sequence starts with all active inputs disabled. 9-6 MS-890 Industrial Automation Scanner User Manual

187 Configuration Database by ESP Calibration Click this button to bring up the Calibration view. Then select the Configuration Database tab to display the view shown below. All the database settings in the <K227> command can be configured in this graphic interface. Save Settings to Configuration Database To save index values by serial command, use the following:<k227+,database index> Load Settings from Configuration Database To load index values by serial command, use the following:<k227-,database index> Request Configuration Database Settings To request index values, use the following:<k227?,database index> or <K227?> for entire database. MS-890 Industrial Automation Scanner User Manual 9-7

188 Optoelectric Control Optoelectric Control Note: Optoelectic Control requires the assembly of a Configuration Database. Optoelectric Control Mode Usage: Definition: Serial Cmd: Default: Options: Useful where different symbol types, sizes, qualities or distances require more that one optical setup (focus, gain, and tracking) for dynamic optical changes. A database index of up to seven pre-defined optical indexes of settings defining focus, gain, and tracking can be accessed and applied in the following modes: A timer in which all settings cycle throughout the time duration. An automatic search for the best database index. A combination of up to three control trigger inputs to dynamically select the optimum database index. The index settings can also be saved and recalled selectively, or reviewed with a Request Database Settings command. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Disabled 0 = Disabled 1 = Control Trigger 2 = Automatic/Static Mode 3 = Timer 4 = Number of Raster Sweeps Disabled Definition: Serial Cmd: When disabled, the scanner uses the standard configuration settings that are set in the Calibration tree and shown to the right of Standard in the Database Index. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> 9-8 MS-890 Industrial Automation Scanner User Manual

189 Control Trigger (Optoelectric Control Mode) Calibration Usage: Definition: Serial Cmd: Useful where different symbol types, sizes, and/or distances benefit from pre-defined optical setups (focus, gain, and tracking) that can be accessed on the fly according to the combination of input states. When Optoelectric Control mode is set to Control Trigger, input 1, new master pin, and the trigger input pins are de-activated and re-assigned as control triggers. When activated, a read cycle will be triggered and in accordance with their respective states selected from a database of up to seven pre-defined optical settings of Focus, Gain, and Tracking. (See Configuration Database on page 9-6) <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Using Control Trigger Set up your application s symbols by symbology type/size in the various positions and/or code type/size at which they will likely appear. Set up your sensors or other controls. For example, the three object sensors, 1, 2 and 3, are connected to input 1, new master pin, and trigger input respectively. The bar-coded packages on the left are numbered here according to their database index numbers. Package # 7 will cross all three of the sensors and thus activate the settings for index # 7. In this scenario only four index settings are possible. However, up to seven combinations are possible with other input devices such as PLCs. You can also enable/disable any combination controls by clicking on the Control Trigger Status buttons on the bottom of the Control Trigger Map. The red buttons indicate active states on the three control triggers. The combination of active/inactive triggers determines the focus, gain, and tracking settings that will be applied during a read cycle. For example, if only Control Trigger 1 is active, the focus, gain, and tracking values that appear in the top row will be applied. MS-890 Industrial Automation Scanner User Manual 9-9

190 Optoelectric Control Automatic/Static (Optoelectric Control Mode) Usage: Definition: Serial Cmd: Useful in a static application in which the symbol is in front of the scanner when the read cycle begins. Selects the optimum setting from the Configuration Database. When selected, the scanner cycles once through all the Configuration Database settings from the closest to the furthermost focal position, testing first for optimal signal, then for a successful decode. Note: Since focus positions are tested in ascending order, the closer the symbols are to the scanner, the quicker the best focus position will be found. Important: The maximum time to move from the most inside focus position to the most outside focus position is 400 ms. One focus position change takes 10 ms. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Timer Mode (Optoelectric Control Mode) Usage: Definition: Serial Cmd: Useful in applications in which there is enough time to cycle through the database index. When this mode is selected, the scanner cycles through database settings at a time interval determined in Timer Value setting. (See Timer/Switch Value on page 9-11.) Important Note: The maximum time to move from the most inside focus position to the most outside focus position is 400 ms. One focus position change takes 10 ms. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Note for Multisymbol: With Multisymbol enabled for more than one symbol, and either Timer or Automatic/Static mode enabled, the scanner may not locate symbols that are scanned at various ranges. The reason for this is that once a symbol is located from the optical database index, the scanner will continue to search for symbols that meet that index of focus, tracking and gain settings MS-890 Industrial Automation Scanner User Manual

191 Number of Active Database Settings Calibration Usage: Definition: Latch on Trigger Can be useful when certain settings that are needed for one application are not needed in another and processing time is at a premium. This value sets the number of configuration database settings (in Database Index) that are active. If Control Trigger mode has been selected, this setting is ignored. Serial Cmd: <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Default: 1 Options: Any number from 1 to 7. Usage: Definition: Serial Cmd: Default: Options: Useful when only one database index is required for the application. This feature is only used in Control Trigger mode. If enabled, the configuration database settings selected at the start of a read cycle will remain active during the entire read cycle. If Latch on Trigger is disabled, depending on the control trigger inputs, the scanner s optical settings can change throughout the read cycle. Note: When Control Trigger #3 is enabled, Latch on Trigger is also enabled regardless of its previous setting. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Enabled 0 = Disabled 1 = Enabled Timer/Switch Value Usage: Useful in slower applications where there is enough time to cycle through the database index. Definition: When Timer mode is enabled, Timer Value is the time interval in which database index settings are cycled. Serial Cmd: <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Default: 5 Options: 0 to 255 (increments of 10ms) MS-890 Industrial Automation Scanner User Manual 9-11

192 Optoelectric Control Control Trigger 1 Status Definition: Serial Cmd: Default: Options: When Control Trigger mode is enabled, Control Trigger #1 takes over Input 1 (see Input Mode on page 6-19) and uses it to select an optoelectric configuration from the configuration database. Active state is set by Input 1 serial command. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Disabled 0 = Disabled 1 = Enabled Control Trigger 2 Status Definition: Serial Cmd: Default: Options: New Master Pin is used for Control Trigger #2. When enabled and Mode is set to Control Trigger, this input is used to select an optoelectric configuration from Configuration Database. Active State is Active Closed. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Disabled 0 = Disabled 1 = Enabled Control Trigger 3 Status Definition: Serial Cmd: Default: Options: Trigger Input is used for Control Trigger #3. When enabled and Mode is set to Control Trigger, this input is used to select an optoelectric configuration from the Configuration Database. Active State is set by the External Trigger State serial command. <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Disabled 0 = Disabled 1 = Enabled 9-12 MS-890 Industrial Automation Scanner User Manual

193 Database Cycles Calibration Definition: Database Cycles refers to the number of times the scanner will load the series of active entries when it is set to Timer or Raster Sweep modes. When set to 0, the scanner will cycle repeatedly through all active database entries until the read cycle ends. When set to a value greater than 0, the scanner will only load the active database entries for the defined number of times before staying with the last active entry for the remainder of the read cycle. Serial Cmd: <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status, database cycles> Default: 0 Options: 0 to 255 MS-890 Industrial Automation Scanner User Manual 9-13

194 Advanced Calibration Features Advanced Calibration Features In the Advanced tab in the Calibration menu you can constrain the scan width of the scan beam with Laser Framing and set up the rules the scanner will follow during calibration procedure. See Laser Framing on page 10-7 for information on laser framing. Auto Range Usage: Definition: Serial Cmd: Default: Options: Enabling Auto Range improves focus acquisition speed where extraneous objects are not mistaken for symbols. With Auto Range enabled, the scanner will focus outward and not begin the calibration routine until an object is detected by signal strength. <K510,auto range,starting focus position,focus step size> Enabled 0 = Disabled 1 = Enabled Using Auto Range 1. Be sure there are no extraneous objects between the symbol and the scanner. 2. Click on the Advanced tab in the Calibration menu. 3. If Auto Range is not enabled, click on it to enable it. 4. Click the Calibrate button to start calibration. 5. Examining the read rates in the Results graph following calibration MS-890 Industrial Automation Scanner User Manual

195 Starting Focus Position Calibration Usage: Starting Focus Position can improve focus acquisition speed during calibration when the approximate range of the symbol is known. Definition: With Auto Range enabled, the scanner will begin the calibration routine at the focal range set in Starting Focus Position. Serial Cmd: <K510,auto range,starting focus position,focus step size> Default: 0 Options: 0 to 40 After you ve used calibration and observed the progress of the first and second passes in the graph and table in the Results tab, you should sense a relationship between focus position and the distance to the symbol. Improving the speed and accuracy of focus position setup: 1. Click on the Advanced tab in the Calibration menu. 2. If Auto Range is enabled, click on it to disable. 3. From previous results, estimate the value of Starting Focus Position and drop down one or two positions. For example, if you estimate the distance to your symbol to correspond to a Starting Focus Position of 6, enter 5 or 4 to be certain of not missing the peak performance distance. 4. Click the Calibrate button to start calibration. 5. Examining the read rates in the Results graph following calibration. MS-890 Industrial Automation Scanner User Manual 9-15

196 Advanced Calibration Features Focus Step Size Usage: Definition: Serial Cmd: Default: 5 Options: 2 to 5 Increasing the Focus Step Size can improve focus acquisition speed for symbols. Focus Step Size is the number of focus increments that will be stepped through during the first calibration pass. The range is 2 to 5. The higher values will result in fewer readings during the first pass but will increase the risk of missing the peak performance position. <K510,auto range,starting focus position,focus step size> Improving the speed and accuracy of focus step size setup: 1. Click on the Advanced tab in the Calibration menu. 2. If Auto Range is enabled, click on it to disable. 3. Enter a value in Focus Step Size. 4. Click the Calibrate button to start calibration. 5. Examine the read rates in the Results graph following calibration MS-890 Industrial Automation Scanner User Manual

197 Calibration by Embedded Menu Calibration To calibrate via the embedded Calibration menu, do the following: 1. Place the sample symbol at a fixed position in the center of the read range being tested. 2. Enter Calibration menu by sending an <@> command from a terminal. 3. If the application requires a change in scan rate, adjust the motor speed now with the M or N commands. Note: All single letter commands must be entered in upper case. 4. Start calibration by typing an uppercase A from your terminal while in the calibration menu. Note: A user can abort calibration at any time by pressing the ESC key on the terminal. No other keystroke has any effect while in calibration. 5. Wait for calibration to cycle through its settings. A Calibration in Progress message will be displayed. A new text line will appear below the menu displaying the progress of the calibration. 6. As with the serial command, repeat the routine at other positions in your scan range and width and save each position to the configuration database. 7. If not successful, a Calibration Failed message will be displayed. If successful, a Calibration Passed message will be displayed along with other settings. Note: Focus positions Inside, Outside, and Set posted near the bottom of the above menu are explained more fully in Calibration Results in Embedded Menus on page Note: If you are using the 9-pin configuration port and doing calibration by serial command or embedded menus, you will be able to view decoded symbol data in the menu. However, after exiting the Calibration menu, you will not be able to see symbol data without sending the following command: <K146,,1>. If using ESP, this is not necessary. MS-890 Industrial Automation Scanner User Manual 9-17

198 Calibration by Embedded Menu Scanner Settings by Embedded Menus Motor Speed, Gain Setting, and Tracking adjustments affect the read performance. Focus controls a stepper motor that physically slides a lens back and forth to control focal length. These settings are adjusted automatically in calibration. The status of these parameters is displayed on the bottom line of the menu under Motor, Gain, Track, and Focus. These settings are incremented or decremented by pressing the indicated key shown on the menu. PDF417 Decode, AGC Status, Laser Power, and Raster Status use single commands to toggle between states. AGC Status Typing S toggles AGC between Enable/Disable, as displayed on a the status line near the bottom of the menu. With AGC disabled this value is simply the Gain setting. However, with AGC enabled, this value represents the gain the scanner has to set to maintain the desired signal amplitude. If a symbol is close to the scanner, the AGC level should be a small value because the scanner does not need much gain to achieve the desired signal amplitude. However, as a symbol gets farther away from the scanner, this value will increase to maintain the signal amplitude. Laser Power Typing L toggles between High and Low laser settings. PDF417 Decode Test Typing D toggles the PDF417 Decode Test between Enable/Disable, as displayed on a the status line near the bottom of the menu. Once set to Enabled, PDF417 only is enabled and a special test mode is enabled that displays the decodes per second of a full PDF417 symbol. While calibration is not performed in this mode, you can still adjust settings manually. This special read rate will remain enabled until the Calibration menu is exited or PDF417 is disabled with another D command. Note: This mode averages decode and capture time over a series of readings, thus assuring for a smooth read rate output, but at the cost of delayed reaction to symbol movement and user setting changes MS-890 Industrial Automation Scanner User Manual

199 Calibration Embedded Menu Options Calibration START Calibration Typing A initiates an calibration sequence. Once entered, no other keystrokes will be accepted with the exception of the ESC key, which terminates the routine. RECALL Initial Settings Typing B restores the original settings that were present upon entering the Calibration Setup Menu. These settings include Motor Speed, Gain, Tracking, and Focus. SAVE Settings to Database Typing C saves the current Gain, Tracking, and Focus settings to the Configuration Database. The database is made up of indexes 1 through 7. Current settings will be saved to the first open index. EXIT Calibration Setup Menu To exit the Calibration Setup menu, press the ESC key. The following prompt will be displayed: Do you want to save calibration settings for power on? (Y=yes N=no). Typing Y will cause the current settings in the Calibration Setup menu to be saved to Flash Memory for recall when the scanner is powered up at a later date. These settings include Motor Speed, Gain, Tracking, Focus, AGC Status, Laser Power, and Raster Status. Typing N will cause the scanner to be reset without saving the settings to Flash memory. Menu Selections Typing 1 will take you to the Calibration Results menu. Typing 2 will take you to the Raster/Laser Framing Setup menu. Typing 3 will take you to the Configuration Database menu. Typing 4 will take you to the Advanced Setup menu. MS-890 Industrial Automation Scanner User Manual 9-19

200 Calibration by Embedded Menu Calibration Results in Embedded Menus To access Calibration Results menu from within the Calibration Setup menu, type the numeral 1. The Calibration Results menu shows the results of the calibration process for Read Rate, Gain, and Tracking for both the first and second passes. Note that the first pass has only one reading for each parameter. Focus Positions In the example above, the focus position selected from the first calibration pass (position 26) represents the optimal focus position for Read Rate, Gain, and Tracking. The second fine tune pass commences 3 focus positions in from this and steps out until the read rate drops off to zero. Focal Range The algorithm selects the best focus position (SET) as the midpoint between those positions (IN and OUT) at which read rates drop off by no more than 6-2/3 percent of the maximum read rate. For example, in the above menu, the read rate for focus position 24 is 73. Since 73 is more than 6-2/3% below the maximum read rate of 100% shown elsewhere, the IN range falls under the next focus position, 25. A mirrored calculation is performed to locate the OUT focal range. Press the enter key (CR) to return to the main calibration menu or ESC to leave the Auto Calibration Setup menu entirely MS-890 Industrial Automation Scanner User Manual

201 Calibration Advanced Calibration Setup Embedded Menu The Calibration Setup menu allows you to change the starting focus position and the number of focus steps during the first pass. For example, if you are preparing to do calibration on symbols whose minimum distances from the scanner is 40 inches, there is no reason for calibration to cycle through all of the focal positions inside 40 inches. To increase Starting Focus Position, type T. To decrease it, type R. To increase the First Pass Focus Step, type G. To decrease it, type F. Increasing First Pass Focus Step will speed up the autofocus process, but can also cause autofocus to skip over a symbol and not decode it. Note: All single letter commands must be entered in upper case. Auto Range is disabled by default. To enable, press A. MS-890 Industrial Automation Scanner User Manual 9-21

202 Calibration by Embedded Menu 9-22 MS-890 Industrial Automation Scanner User Manual

203 10 Raster/Laser Contents Raster/Laser Setup by ESP Raster/Laser Serial Commands Raster Setup Laser Framing Raster/Laser by Embedded Menu This section explains the setup and adjustments for the raster and laser. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. Note: Raster setup commands in the ESP are accessed from the Read Cycle/Triggering menu or from the Raster/Laser or Calibration menus on the ESP toolbar. MS-890 Industrial Automation Scanner User Manual 10-1

204 Raster/Laser Setup by ESP Raster/Laser Setup by ESP Click this button to bring up the Raster/Laser menu. To open nested options, single-click the +. To change a setting, double-click the setting and use your cursor to scroll through the options. Raster/Laser Serial Commands Command Title Raster Laser On/Off Format <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> <K700,laser on/off status,laser framing status,laser on position,laser off position, laser power> 10-2 MS-890 Industrial Automation Scanner User Manual

205 Raster Setup Raster/Laser You can set up and make changes to the scanner s raster parameters in ESP s Read Cycle, Calibration, or Raster/Laser views (preferred). To access the Raster Setup menu, click the Raster/Laser button and the Raster Setup tab. Usage: Definition: Raster scanning is useful when symbols vary in placement and a single scan line cannot be counted on to cross the symbol, and for reading stacked symbologies such as PDF417. The user can enable raster scanning and adjust the raster sweep limits and the sweep rate. Note: Changes made in the Raster Setup menu are dynamic; that is, they take effect without saving. MS-890 Industrial Automation Scanner User Manual 10-3

206 Raster Setup Raster Status Definition: Serial Cmd: Default: When disabled, the raster mirror will park at the top of the raster sweep. <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> Disabled Options: 0 = Disabled 1 = Enabled Note: Raster sweeps are only counted during a read cycle (continuous, triggered, and read rate). Raster sweeps are NOT counted when the raster motor is parked, disabled, set to straight line operation (top and bottom are equal), or when performing a self-calibration. Top Offset Definition: Serial Cmd: Default: 127 Options: 0 to 255 Decreasing the Top Offset value causes the top of the raster pattern to move up. <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> 10-4 MS-890 Industrial Automation Scanner User Manual

207 Bottom Offset Raster/Laser Definition: Serial Cmd: Default: 127 Increasing the Bottom Offset value causes the bottom of the raster pattern to move down. <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> Options: 0 to 255 Note: For single scan line operation, set Top Offset equal to Bottom Offset or click on the Static Line option. Note: Assigning a larger value to Top Offset than Bottom Offset will park the raster mirror in its home (default) position. Raster Sweep Rate Usage: If your application allows it, a slower sweep rate can produce more scans per second and higher read rates. To determine the minimum read rate for your application, see Raster Picket Fence Calculation on page A-28. Definition: The raster sweep rate is the number of sweeps per second the raster mirror completes. A sweep is one pass of the raster, up or down. The maximum sweep rate is limited by the size of the arc the raster must move through. Serial Cmd: <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> Default: 10 Options: 0 to 30. The table below shows the maximum speeds at selected raster sweep arcs. To maximize the number of scans per symbol, use the lowest effective sweep rate required for the application. Raster Sweep Arc Maximum Sweeps per Second 0 to to to MS-890 Industrial Automation Scanner User Manual 10-5

208 Raster Setup Read Cycle On/Off Usage: Definition: Serial Cmd: Default: This feature should only be used when the raster sweep rate is at least twice the required trigger rate (decoded outputs per second). When Read Cycle On/Off is enabled and Laser On/Off is also enabled, the raster mirror stops at top offset at the end of triggered read cycle. <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> Disabled Options: 0 = Disabled 1 = Enabled 10-6 MS-890 Industrial Automation Scanner User Manual

209 Laser Framing Raster/Laser To access the Laser Framing menu, click the Raster/Laser button and the Laser Framing tab. Laser On/Off Status Usage: Definition: Serial Cmd: Default: Laser On/Off extends the life of the laser. It is useful where there are significant time gaps between symbols. It also provides visual confirmation of a read cycle timeout and minimizes laser exposure to people. When enabled, the laser is ON only during the read cycle. When disabled, the laser operates continuously. <K700,laser on/off status,laser framing status,laser on position,laser off position,laser power> Disabled Options: 0 = Disabled 1 = Enabled Note: A serial or external trigger must be enabled for Laser On/Off to take effect. Note: Laser On/Off is not recommended when New Trigger is enabled, since the laser will effectively remain on continuously. MS-890 Industrial Automation Scanner User Manual 10-7

210 Laser Framing Laser Framing Status Usage: Definition: Serial Cmd: Default: Useful in avoiding highly reflective objects, for filtering out unwanted signals, or avoiding the wrong symbols. Sets the length of time the laser is ON during each scan so that only a selected portion of the scan width is effectively scanned. <K700,laser on/off status,laser framing status,laser on position,laser off position,laser power> Disabled Options: 0 = Disabled 1 = Enabled To adjust laser framing, click the Raster button, click the Laser Setup tab, and click the Laser On and Laser Off arrows up or down. When Laser Framing is not enabled, the scan beam sweeps across the full scan width. When enabled, the laser remains OFF during the Laser Off Time beginning at the start of the scan beam sweep and turns ON for the duration of the Laser On Time. Laser On Position Definition: Laser Off Position Laser Power Measured in increments equal to 1/100th of total scan width. Serial Cmd: <K700,laser on/off status,laser framing status,laser on position,laser off position, laser power> Default: 10 Options: 10 to 90 Definition: Measured in increments equal to 1/100th of total scan width. Serial Cmd: <K700,laser on/off status,laser framing status,laser on position,laser off position, laser power> Default: 95 Options: 15 to 95 Usage: Used to optimize read performance at different distances. Typically higher power is used at greater distances. Definition: Allows the user or calibration routine to select laser power setting. Serial Cmd: <K700,laser on/off status,laser framing status,laser on position,laser off position, laser power> Default: High Power (low or medium density scanner) Options: 0 = Low (3.0 mw) 1 = Medium (3.25 mw) 2 = High (3.5 mw) 10-8 MS-890 Industrial Automation Scanner User Manual

211 Raster/Laser by Embedded Menu Raster/Laser To access the Raster/Laser Framing menu, send to open the Calibration Setup menu and type the number 2. Raster Settings Type the letter T to increment the Top Offset and an R to decrement. Notice that the Top Offset reading at the bottom of the menu changes accordingly. Type the letter B to increment the Bottom Offset and V to decrement. Sweep Rate, Raster Status, and Raster On/Off are explained more fully in Raster Setup on page Laser Settings Laser settings are also dynamically updated at the bottom of the menu. Full instructions and menus for laser operations can be found in Laser Framing on page Press the enter key (CR) to return to the main calibration menu or ESC to leave the Auto Calibration Setup menu entirely. MS-890 Industrial Automation Scanner User Manual 10-9

212 Raster/Laser by Embedded Menu MS-890 Industrial Automation Scanner User Manual

213 11 Terminal Contents Terminal Window Find Send Macros Terminal Window Menus This section describes the Terminal window and macro functions. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. MS-890 Industrial Automation Scanner User Manual 11-1

214 Terminal Window Terminal Window Click this button to bring up the Terminal view. The following window will appear: Copy, paste, save Clear screen Type text here to find matching text in the Terminal window. Terminal screen Type serial commands here. Macros listed on this bar Click on Macros arrow to Add Macro, Remove Macro, or Edit Macro. Click on desired Macro to run. The Terminal screen allows you to send serial commands to the scanner by using Macros, by copying and pasting, or by typing commands in the Send text field. The Terminal screen also displays symbol data or information from the scanner. You can also right-click on the Terminal screen to bring up a menu of further options MS-890 Industrial Automation Scanner User Manual

215 Find Terminal The Find function allows you to enter text strings to be searched for in the Terminal window. For example, a series of symbols have been scanned into the Terminal view and you want to determine if a particular symbol whose data begins with ABC has been read. 1. Type ABC into the Find box. 2. Press Enter. The first instance of ABC will be highlighted in the Terminal window. 3. Click the Find button to the right of the text field to locate additional instances of ABC. MS-890 Industrial Automation Scanner User Manual 11-3

216 Send Send The Send function in ESP s Terminal allows you to enter serial commands and then send them to the scanner. 1. Type the command into the Send box. 2. Press Enter. 3. Click the Send button to the left of the text field to send MS-890 Industrial Automation Scanner User Manual

217 Macros Terminal Macros can be stored in a macro selection bar, edited in a separate window, and executed by clicking on the macro name. Click on Next Row to see the next row of macros Click on the first arrow here to see Add Macro or Default Macros. When you default macros, the entire macros set is restored to their original macro commands. Click on subsequent arrows to edit macros. When you click on the macro name, the macro is executed in the Terminal window. If this is a command, it is sent to the scanner at the same time that it is displayed. Editing a Macro When you click the arrow next to any macro and select Edit, the following appears: You can edit an existing macro or type in the Macro Name text field and define it in the Macro Value text field. Click OK. MS-890 Industrial Automation Scanner User Manual 11-5

218 Terminal Window Menus Terminal Window Menus Right-click on the Terminal window to display the following menu: Copy selected text to clipboard. Paste from Terminal or computer text. Clear all text in Terminal window. Select All text in the Terminal window. Save... brings up a save as dialog box. Change Font... of data text, brings up a text dialog. Change Echo Font... to change typed in text or commands. Change Background Color of Terminal window. Default Settings changes all the above back to default settings. Terminal Dropdown Menu The dropdown Terminal menu has Capture Text and Save Current Text functions, as well as the functions defined above. Capture lets you append data in real time to a text file of your choice. While in operation, the text file cannot be opened. You can select Pause to interrupt the capture flow or Stop to end the flow and open the file. Save Current Text... saves all text in the Terminal window to a text file of your choice MS-890 Industrial Automation Scanner User Manual

219 12 Utilities Contents Serial Utility Commands Read Rate Counters Device Control Differences from Default Master Database Digital Bar Code Firmware Autodiscriminate Scanner Status Requests Utility commands are generally commands that are performed during scanner operations to check read rates, determine read rates or perform miscellaneous operations on scanner hardware. Serial utility commands are not prefaced with a K and a numeric code, nor do they require an initialization command (<A> and <Z>). They can be entered from within any terminal program or from within ESP in the Terminal window. Note: The characters NUL, <, >, and, can only be entered through embedded menus, not through ESP or serial commands. MS-890 Industrial Automation Scanner User Manual 12-1

220 Serial Utility Commands Serial Utility Commands Command Type Command Name Read Rate <C> Enter Read Rate Test <Cs> Enter Multisymbol Read Rate Test <Cp> Enter Percent Test <Cm> Enter Multisymbol Percent Test <Ce> Extended Read Rate <CPDF> Enter Percent PDF Read Rate Test <J> Exit Read Rate and Percent Test Counters <N> No Read Counter <O> No Read Counter Reset <T> Trigger Counter <U> Trigger Counter Reset <V> Good Read/Match Counter <W> Good Read/Match Counter Reset <X> Mismatch Counter <Y> Mismatch Counter Reset Device Control <H> Enable Laser Scanning (Laser On) <I> Disable Laser Scanning (Laser Off) <K500> Motor On <K501> Motor Off <L1> Programmable Output 1 Pulse <L2> Programmable Output 2 Pulse <L3> Programmable Output 3 Pulse Matchcode <E> Enable Matchcode Type <F> Disable Matchcode Type <G> Store Next Symbol to Database Index 1 Master Database <Gn> Store Next Symbol to Database Index n <Mn> Download Master Symbol Data to Database Index n <Mn?> Display Master Symbol Data from Database Index n <Mn,> Delete Master Symbol from Database Index n Firmware <!> Display Checksums for Boot Code and Application Code <!b> Display Checksum for Boot Code <!a> Display Checksum for Application Code <!c> Display Checksum for Raster Code <#> Display Boot Code and Application Code Part Number <#b> Display Boot Code Part Number <#a> Display Application Code Part Number Symbologies <P> Autodiscriminate All Symbologies <Q> Enable Code 39 Only <R> Enable Codabar Only <S> Enable Interleaved 2/5 Only Trigger <char> Serial Trigger Character 12-2 MS-890 Industrial Automation Scanner User Manual

221 Utilities Default/Reset/Save <A> Reset (does not save for Power-On) <An> Reset and Read Flash Parameters <Z> Save Current Settings for Power-On Status Requests <?> Status Byte <?1> Extended Status <K?> All Commands Status <K??> Single Command Status <K?# All Command Descriptions <Knnn?> Single Command Description <Knnn??> All Command Ranges <Knnn?#> Single Command Range <Knnn?*> Single Command Wildcard <Knnnd> Single Command Default MS-890 Industrial Automation Scanner User Manual 12-3

222 Read Rate Read Rate You can access Read Rate from the Utilities menu. To start or end a read rate test, right-click Read Rate and select Start or Stop. To change from percent read rate to decodes per second, first end the read rate by selecting Stop, then right-click select Decodes/Sec. Read Rate by Serial Command Enter Single Symbol Percent Test Sending <Cp> instructs the scanner to transmit the percentage of decodes and any scanned symbol data. Enter Multisymbol Percent Test Sending <Cm> instructs the scanner to transmit the percentage of scans decoded and symbol data (if any) for multiple symbols. Enter Single Symbol Read Rate Test Sending <C> instructs the scanner to transmit the decodes per second and symbol data (if any). The decode rate can vary dramatically due to the angle and location of the symbol in relation to the scan line. This test is very useful in aligning and positioning the scanning device during installation. Enter Multisymbol Read Rate Test Sending <Cs> instructs the scanner to transmit the decode rate and symbol data (if any) for multiple symbols. Enter Percent PDF Read Rate Test Sending <CPDF> instructs the scanner to transmit the number of decodes per second on the full PDF symbol. This test includes both capture and decode and translation time. Note that the output format of the data is done as a running average of 750ms windows. This means that you can remove the symbol from the view of the scanner and it will continue to transmit some history of the symbol for a few outputs. Enable PDF Information Sending the <a1> check box will cause PDF417 symbology data to be prefaced with information consisting of error correction level, number of rows, number of columns, number of informative code words and the number of data characters. This feature can be disabled by using the exit read rate command <J> MS-890 Industrial Automation Scanner User Manual

223 Utilities Enable Extended Read Rate Test for Single and Multisymbol Sending <Ce> after <C> or <Cs> will generate a an extended mode that applies to both single and multiple symbols. Extended Mode instructs the scanner to output the decode rate, the symbol data, and the transition data. The example below shows output with Postamble enabled and defined as Carriage Return/Line Feed. Decode rate Symbol data Number of bar/space transitions Note: The <Ce> command has no immediate effect if not preceded by <C> or <Cs>. End Read Rate Test Sending <J> ends both the Percent test and the Decodes/Second test for both single and multisymbol. MS-890 Industrial Automation Scanner User Manual 12-5

224 Counters Counters Counter commands can be a numeric value from to After reaching the maximum numeric limit of 65,535, the counter will automatically rollover and start counting again at and report any errors. To obtain the cumulative total of counts after the rollover has occurred, add 65,536 per each rollover (the scanner does not keep track of the number of rollovers) to the current count. Note: All counter values will be lost if power is recycled to the scanner or the scanner receives a reset or save command. Counters by Serial Command No Read Counter Sending <N> displays the total number of No Reads that have occurred since the last reset. No Read Counter Reset Sending <O> sets No Read Counter to Trigger Counter Sending <T> displays the total number of triggers since the last reset. Trigger Counter Reset Sending <U> sets the trigger counter to MS-890 Industrial Automation Scanner User Manual

225 Utilities Good Read/Match Counter Sending <V> displays the total number of good reads matching the master symbol if Matchcode is enabled. This counter is always enabled, but will only work as a match count when Matchcode is enabled. If Matchcode is not enabled, this counter records the number of good reads. This count can be requested at any time. Good Read/Match Counter Reset Sending <W> sets the match counter to Mismatch Counter With Matchcode enabled, sending <X> displays the number of decoded symbols since the last reset that do not match the master symbol. Mismatch Counter Reset Sending <Y> sets the mismatch counter to zero. MS-890 Industrial Automation Scanner User Manual 12-7

226 Device Control Device Control Device Control is accessible from the Utilities menu. Device Control by Serial Command Enable Laser Scanning Sending <H> will turn the laser on continuously. Note: Enable Laser Scanning does not relate to Laser On/Off command. Disable Laser Scanning Sending <I> will turn the laser off and end the current read cycle. This feature is useful during extended periods of time when no symbols are being scanned or the scanner is being configured. Disabling laser scanning will not affect any downloaded commands to the scanner. Note: Disable Laser Scanning does not relate to Laser On/Off, which, when enabled, also turns off the laser but only between read cycles. Motor On Sending <KE> turns the spinning mirror and raster mirror motors on (if not already running). Note: The spinning mirror reaches full speed after a short time delay. Motor Off Sending <KF> turns the spinning mirror motor off. This command is useful for long idle periods. Note: Laser turns off whenever motor is off MS-890 Industrial Automation Scanner User Manual

227 Utilities Output 1 Sending <L1> activates the link between Output 1(+) and Output 1( ) of the host connector (regardless of Master Symbol or Output 1 status). Output 2 Sending <L2> activates the link between Output 2(+) and Output 2( ) of the host connector (regardless of Master Symbol or Output 2 status). Output 3 Sending <L3> activates the link between Output 3(+) and Output 3( ) of the host connector (regardless of Master Symbol or Output 3 status). MS-890 Industrial Automation Scanner User Manual 12-9

228 Differences from Default Differences from Default Clicking the Differences from Default button will cause ESP to check all stored configuration settings and compare them to default settings. All settings that are different than default will appear in the left column (shown below), and descriptions of those settings will appear in the right column. Click this button for a list of ESP configuration settings that are different than default settings. Click Generate Barcode to bring up the Bar Code Dialog. Then create configuration symbols containing the configuration commands of your choice. Send configuration settings to the scanner without saving by clicking Send to Reader. Click Save As to save the report as plain text or a tab-delimited text file. Send configuration settings to the scanner and save in ESP by clicking Send and Save. To create a symbol containing any of the command settings in the table, click Generate Barcode. This will bring up the Bar Code Dialog. To save the Differences from Default report, either as plain text or as a tab-delimited text file, click Save As. Click Send and Save to send the settings to the scanner and save them, or Send to Reader to send the settings without saving them. Important: The use the Differences from Default feature, you must connect to the scanner and Receive Reader Settings via the Send/Recv button on the toolbar MS-890 Industrial Automation Scanner User Manual

229 Master Database Utilities Important: Master Database is used only for comparing entire symbols, when Sequential and Wild Card are NOT enabled, and Start Position is equal to 0. Master Database Overview Usage: Used where more than one master symbol is required, as in a Multisymbol setup, for matching and other matchcode operations. Definition: Allows you to define up to 10 master symbols as the master symbol database, which can be entered by keyboard, scanned in, displayed, or deleted by serial or ESP commands. 1. Click the Master Database tab. 2. Set the Master Symbol Database Size. 3. Select database index you want to enter the master symbol. 4. Do one of the following to enter master symbol data: Double-click the index row to type data directly into index. (See Enter Master Symbol Data on page ) Click Read Symbol into Selected Index to enter the next decoded symbol. Set Master Symbol Database Size here. Loads the next symbol decoded into the selected index. Double-click a row to enter data into popup dialog box. Loads the scanner s saved master symbols into ESP. Saves the displayed database to the scanner. MS-890 Industrial Automation Scanner User Manual 12-11

230 Master Database Master Symbol Database Size Definition: ESP: Serial Cmd: Default: 1 Options: 1 to 10 Master Symbol Database Size allows you to select 1 to 10 master symbols for the master symbol database. First set the number of master symbols you want to include by double-clicking Database Size and entering the number. <K224,master symbol database size> Set Master Symbol Database Size here MS-890 Industrial Automation Scanner User Manual

231 Enter Master Symbol Data Utilities Definition: ESP: Serial Cmd: Default: Allows you to enter master symbol data for a specific master symbol index number (1 to 10), provided the index number is not larger than the number of symbols enabled by the Master Symbol Database Size. For example, if Master Symbol Database Size is set to 2, you will not be able to enter data for symbols 3 through 10. Double-click on the index row. <K231,master symbol number,master symbol data> 1, (blank) Options: 1 to 10, any combination of ASCII text up to the maximum indicated in the Maximum Characters for Master Symbol Database table below. For example, to enter data for master symbol 9, after making certain that master symbol database size is enabled for 9 or more symbols (see Master Symbol Database Size on page 12-12), send <K231,9,data>. Caution: Since the total number of characters available for the master symbol database is 2710 changes to the Master Symbol Database Size will re-allocate the number of characters available for each master symbol and could cause existing master symbols to be deleted (except master symbol #1 unless it also exceeds the size limitation). The table below specifies the maximum number of characters available to each symbol according to the number of master symbols defined, from 1 through 10. See Master Symbol Database Size on page Maximum Characters for Master Symbol Database Number of Master Number of Master Maximum Characters Symbols Symbols Maximum Characters # #6 340 # #7 291 #3 681 #8 254 #4 510 #9 226 #5 408 # MS-890 Industrial Automation Scanner User Manual 12-13

232 Master Database Request Master Symbol Data Definition: Returns master symbol data for any enabled master symbols from 1 to 10. For example, to request master symbol # 5, enter <K231?,5>. The scanner transmits the following format: <K231,5,data>. If no master symbol data available, the output will be: <M5/?>. Serial Cmd: Send <K231?,master symbol number,master symbol data> to request the current master symbol for a specific master symbol. Returns all master symbols if no number is added before the question mark. Options: 1 to 10 Delete Master Symbol Data Definition: ESP: Serial Cmd: This command will delete the current master symbol data. You can delete master symbol data for any master symbol by erasing the data in the Master Database popup dialog (under Output Format) and clicking OK. <K231,master symbol number,>to delete a master symbol, enter the database number and a comma, but leave the data field empty. For example, to delete master symbol #5, send the following <K231,5,>. The command is entered with a blank master symbol data field which tells the scanner to delete the selected master symbol from the database MS-890 Industrial Automation Scanner User Manual

233 Read Next Symbol as Master Symbol Utilities Definition: After you ve set the size in the database, you can order the scanner to read the next symbol as the master symbol. ESP: In the Master Database tab, under the Output Format menu: 1. Select the master symbol index number in which you want to store the symbol data. 2. Click Read Symbol into Selected Index. Serial Cmd: <Gmaster symbol number> To store the next symbol scanned as master symbol #1 send: <G> or <G1>. For all symbols numbers except 1, the number must be included. Options: 1 to 10 Note: Utility commands are not accessible by embedded menus. MS-890 Industrial Automation Scanner User Manual 12-15

234 Digital Bar Code Digital Bar Code When you click the Digital Bar Code tab and the Start button, a digitized representation of the candidate symbol will appear. This routine is useful for conveying a sense of the symbol s readability and graphically indicating bad or unreadable portions of symbols or extraneous noise. A green waveform indicates a decoded symbol; a red waveform indicates an undecoded symbol or other object. The red triangles represent the width of the scan beam relative to the symbol. The upward pointing arrows indicated the symbol s margin. Zoom In, Zoom Out You can zoom in by sliding the Zoom lever to the right. You may have to scroll right or left to locate your symbol, but the results will be striking MS-890 Industrial Automation Scanner User Manual

235 Firmware Firmware Update Utilities Firmware Update is used to download application code to the scanner. Application code versions are specific to your scanner. Consult with your sales representative before downloading application code. If needed, an application code will be sent to you in the form of a *.mot file. To download application code: 1. First make sure the host is connected to your scanner. 2. Apply power to the scanner. 3. Before updating, verify the current firmware (see Firmware Verification (Part Number) below.) 4. Click in the Firmware Update text box and select the file type you want to download. This will open a file locator box. 5. Navigate to the appropriate file (a *.mot file) and open the file. As application code begins to download to the scanner, the scanner will go silent, the scanner s RDY and GD/RD LEDs will flash intermittently, and a progress indicator at the bottom of the ESP window will let you know when the download is complete. Caution: Do not interrupt power or disconnect the host cable while download is in progress. MS-890 Industrial Automation Scanner User Manual 12-17

236 Firmware Firmware Verification (Part Number) You can send a request for the scanner s current firmware part numbers using this dialog: 1. From the Utilities menu you can access Firmware Verification from the Firmware tab. 2. Select the firmware code you want to check and click Request Part No. to see the associated part number. Part Number by Serial Command Upon sending <#> the scanner returns software part numbers for application code <#a/ > and boot code <#b/ >. Individual part numbers for Application Code and Boot Code are returned when their respective commands <#a> and <#b> are sent. Firmware Verification (Checksum) A checksum verifies a scanner s flash memory. 1. From the Utilities menu you can access Firmware Verification from the Firmware tab. 2. Select the firmware code you want to check and click Request Checksum to see the associated part number. Checksum by Serial Command Upon sending <!> the scanner returns two 4-digit hex numbers that are the check sums for boot code and the application code. Individual checksums for Boot Code and Application Code are returned when their respective commands <!b> and <!a> and <!r> are sent MS-890 Industrial Automation Scanner User Manual

237 Autodiscriminate You can enable most or specific symbol types by the following operational commands. Utilities Default: Options: Code 39 (only) <P> Enables most symbol types. <Q> Enable Code 39 only <R> Enable Codabar only <S> Enable I 2/5 only MS-890 Industrial Automation Scanner User Manual 12-19

238 Scanner Status Requests Scanner Status Requests <?> Status Byte The scanner responds to a status request <?> with a two character hex value, for example <?/22>. To determine the status: 1. Look up the binary conversion in the hex-to-binary table. For example, the first 2 in binary would be as read from binary digits 3 through 0; the second 2 the binary digits 7 through 4 which is also Next, enter your binary values in the Scanner Status table, in the Binary column next to the appropriate bit. Bit Binary Scanner Status 0 0 Command error detected 1 1 Command received 2 0 Communication error detected 3 0 Flash sector unprotect failure 4 0 Host/Aux port buffer overflow 5 1 Scanner is in a read cycle 6 0 Software Watchdog reset 7 0 Hardware Watchdog reset 3. Under Binary, interpret 1s as true and the 0s as not true. For example, bit 1 has a 1 in the Binary column, indicating Command Received. Bit 5 is also a 1 indicating that the Scanner is in a read cycle. Hex Value A B C D E F Binary Bit Digits <?1 > Extended Status The scanner responds to an extended status request <?1> with several fields, for example: <?1/20>< , ,F6D4,20C5,02D3,02D3>. These represent, in order: the status byte discussed above, the boot part number ( ), the application part number ( ), boot checksum (5F6D4), app checksum (02D3), RAM parameter checksum (02D3), and flash parameter checksum (02D3). <K?> All Commands Status This is the fastest way to learn the scanner s current configuration. Sending this request will return the current settings of all commands, starting with the lowest K command value and ending with the highest K command value. <Knnn?> Single Command Status This request will return the value of the variables associated with the requested K command. The request of a single entry of a database command cannot exceed the number of database slots for the specific command MS-890 Industrial Automation Scanner User Manual

239 Utilities <K??> All Command Descriptions This request will return all current descriptions of every K command, starting with the lowest K command value and ending with the highest K command value. <Knnn??> Single Command Description This request returns the basic functional description of all fields in the requested K command. <K?#> All Command Ranges This request will return the current settings of all commands within the user-defined range, starting with the lowest user-defined K command value and ending with the highest user-defined K command value. <Knnn?#> Single Command Range This request will return the value range and storage type description of all fields in the requested K command. <Knnn?*> Single Command Wildcard This request will return the requested K command s status, description, and range for all parameters. <Knnnd> Single Command Default This request will default a single K command for the user, provided that the requested K command has user-defined parameters (rather than factory-defined parameters). MS-890 Industrial Automation Scanner User Manual 12-21

240 Scanner Status Requests MS-890 Industrial Automation Scanner User Manual

241 13 Output Format Contents Output Format Serial Commands Output Format Status Format Assign Format Extract Format Insert Output Filter Configuration Number of Filters This section explains how to control the formatting and filtering of decoded symbol data for output. MS-890 Industrial Automation Scanner User Manual 13-1

242 Output Format Serial Commands Output Format Serial Commands Command Title Format Extract Format Insert Format Assign Format Status Output Filter Configuration Number of Filters Command Format <K740,output index,start location,length> <K741,output index,length,hex string> <K742,symbol number,status> <K743,output format status> <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> <K745,number of filters> 13-2 MS-890 Industrial Automation Scanner User Manual

243 Output Format Status Output Format Definition: Serial Cmd: Default: Options: This is a global enable/disable parameter. In order to use formatting you must set up the format using the insert and extract commands, and you must also assign a symbol to format using the Format Assign command. <K743,output format status> Disabled 0 = Disabled 1 = Enabled Output Format Status Disabled When Format Status is set to Disabled, output formatting is globally disabled. Output Format Status Enabled When Format Status is set to Enabled, output formatting is enabled. However, Format Assign, Format Insert, and Format Extract must be properly set up as well. Output Format Status by ESP On the Output Format tab, check the Enable Output Format box. MS-890 Industrial Automation Scanner User Manual 13-3

244 Format Assign Format Assign Symbol Number Definition: Serial Cmd: Symbol Number refers to the number of the symbol to which output formatting will apply. For example, if you wish to enable user-defined formatting to symbol # 2 in a multisymbol read cycle, you would send the command <K742,2,1>. Note that the number of symbols may exceed the format capabilities. <K742,symbol number,status> Options: 1 to 12 1 = Formatted output status for symbol # 1. 2 = Formatted output status for symbol # = Formatted output status for symbol # 12. Format Assign Status Definition: Serial Cmd: Default: Options: Status refers to the user-defined formatting of a selected symbol position in the read cycle result. Note that there is also a global formatting enable command that must be set for the formatting to be applied. <K742,symbol number,status> Disabled 0 = Disabled 1 = Enabled (Assign parameters to specified symbol) Format Assign by ESP Use the Set Number of Symbols spin box to determine the number of symbols to be included in the output phrase. Then check the Parse boxes beneath the symbols that you wish to format for user-defined output MS-890 Industrial Automation Scanner User Manual

245 Format Extract Output Format Output Index Definition: Output Index refers to the database entry you wish to modify with this command. A formatted output is built by extracting data from a symbol s original data output and/or inserting user-defined characters. It may be helpful to think of individual indexes as positions in the final formatted output you wish to build. Starting with index # 1, enter either an extract or insert command to begin building your desired output string. Then, with the next index number, enter either an extract or insert command to continue building the output string. Continue this process until you are finished building the string. Serial Cmd: <K740,output index,start location,length> Options: 1 to 100 Start Location Definition: Defines the location within the symbol data where the character extraction will begin. The first character extracted will also be the first character in the sequence displayed in user-defined output. Serial Cmd: <K740,output index,start location,length> Default: 0 Options: 1 to n (maximum number of characters in symbol data) Length Definition: Serial Cmd: Default: Options: Defines the length (in consecutive characters) that will be extracted and placed in user-defined output. <K740,output index,start location,length> 0 (disabled; end of format cell array) 1 to n (maximum number of characters in symbol data) MS-890 Industrial Automation Scanner User Manual 13-5

246 Format Assign Format Extract by ESP The Extract Range function corresponds to the Start Location and Length parameters in the Format Extract serial command. You can extract and insert several character sequences using ESP s Symbol Parse feature. In this example, the selected extraction range is characters 2-4. The Sample Symbol example on the Symbol Parse dialog shows the selected character positions extracted and output as desired. Simultaneously, the data string from the actual selected symbol is displayed at the bottom left of the Parse Table, followed by the user-defined extracted output MS-890 Industrial Automation Scanner User Manual

247 Format Insert Output Index Length Hex String Output Format Definition: Output Index refers to the database entry you wish to modify with this command. A formatted output is built by extracting data from a symbol s original data output and/or inserting user-defined characters. It may be helpful to think of individual indexes as positions in the final formatted output you wish to build. Starting with index # 1, enter either an extract or insert command to begin building your desired output string. Then, with the next index number, enter either an extract or insert command to continue building the output string. Continue this process until you are finished building the string. Serial Cmd: <K741,output index,length,hex string> Options: 1 to 100 Definition: Specifies the length of the user-defined character string that will be inserted. This function is limited to 4 characters per output index, so multiple indexes must be entered in order to insert longer character sequences. For example, if you wish to insert a 10 character sequence in user-defined output, you would need three commands with consecutive index numbers, where the first two character sequence lengths were 4 and the third was 2. Serial Cmd: <K741,output index,length,hex string> Default: 0 (disabled; end of format cell array) Options: 1 to 4 Definition: Serial Cmd: Default: Options: Specifies a character string that represents ASCII characters to be inserted in the database entry. Two hex characters are required for every ASCII character to be inserted in the user-defined output string. These two characters comprise the hex (base 16) value of the ASCII character. For example, if you wanted to enter the three-character sequence Hi! you would enter 3 for the length of the string, and a hex sequence of for the ASCII sequence to be inserted. (48 = H; 69 = i; 21 =!) Important: Each pair of hex characters represents one ASCII character. Hex character pairs range from 00 to FF. Since you are limited to 4 ASCII characters per insertion per database entry, you are likewise limited to 8 hex characters per insertion per database entry. <K741,output index,length,hex string> NUL (00 in hex) 00 to FF (As many as 4 bytes, or hex pairs.) MS-890 Industrial Automation Scanner User Manual 13-7

248 Format Insert Format Insert by ESP The Format Insert process is very similar to the Format Extract process, except that Insert allows you to enter characters using the Insertion Calculator (shown above). Notice that Extract and Insert share the same Parse Table MS-890 Industrial Automation Scanner User Manual

249 Output Filter Configuration Output Format Definition: Serial Cmd: Output filtering is a method of providing a set of good read qualifiers and also providing ordered output. There is a filter for up to the first 10 positions in a multisymbol output. The first filter corresponds to the first symbol output at the end of the read cycle. Each filter has has settings for the following four parameters: Symbology Type, Symbol Length, Data, and Configuration Database Number. <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> Rules for Output Filter Configuration Output Filter Configuration Rule # 1 Each symbol that is decoded must match one of the filters before it can be saved to a read cycle record. There is an exception to this rule, however, when the number of symbols required for a read cycle exceeds the number of active filters. In such a case, unfiltered symbols can be placed into unfiltered output positions. For example, if the number of symbols required is 6 but there are only 4 active filters, the last 2 positions can be filled by any (unfiltered) qualified symbol. Output Filter Configuration Rule # 2 The same filter setup can be used multiple times. For example, filters 1, 2, and 3 can be set up to filter Data Matrix symbols, and the output will occur in the order the symbols are decoded. Output Filter Configuration Rule # 3 All qualified symbols will be sorted and output in the matching filter position. If a symbol matches filter 3, it will be output as the third symbol. If a filter does not have a matching qualified symbol, a No Read message will be output in place of the symbol (assuming the No Read message is enabled). For example, if there is not a symbol that meets filter 3 s requirements, then a No Read message will be output in the third output position. MS-890 Industrial Automation Scanner User Manual 13-9

250 Output Filter Configuration Filter Number Definition: This is the filter index number that represents the position of the symbol in the data output at the end of the read cycle. This index number should be entered along with the following filter settings for the predetermined symbol position. Serial Cmd: <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> Options: 1 to 12 Symbology Definition: Serial Cmd: Default: Options: Specifies the symbology type allowed to occupy this location in multisymbol output. Note: To filter or order a symbol, the symbol must meet all the requirements of the selected filter index. <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> 0 (any symbology type) 0 = Any type 1 = Interleaved 2 of 5 2 = Code 39 3 = Code = Codabar 5 = UPC 6 = PDF417 7 = EAN = Code 93 9 = Pharmacode MS-890 Industrial Automation Scanner User Manual

251 Length Output Format Definition: Specifies the length of the decoded symbol allowed to occupy this location in multisymbol output. Note: To filter or order a symbol, the symbol must meet all requirements of the selected filter index. Serial Cmd: <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> Default: 0 Options: 0 to 128 Wildcard Definition: Serial Cmd: Default: Options: This is the character to be used in the data output field when performing a data filter comparison. The wildcard character represents the end of matching, and allows for variable lengths of symbol output. <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> * = (2A in hex) Any ASCII input in the form of a pair of hex characters. Example: 2A = * 00 = disabled Placeholder Definition: Serial Cmd: Default: Options: The placeholder character requires a character to be present, but does not compare the data value. <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index>? = (3F in hex) Any ASCII input in the form of a pair of hex characters. Example: 3F =? 00 = disabled MS-890 Industrial Automation Scanner User Manual 13-11

252 Output Filter Configuration Data Definition: Serial Cmd: Default: Options: This is the data string to be used when comparing symbol data for output filtering and ordering. This data string may also contain wildcard and placeholder characters to facilitate matching. Remember that in order to filter or order symbol data, it must meet all the requirements of the selected filter index. Examples: Filter data = 123*. This will match data strings of 123, , and 123ABC, but not 12. Filter data = 123*AB?C. This will be interpreted as 123*. Filter data = 123?. This will match 1234 and 123A, but not 123, 12345, or 1234C. Filter data = 123?A. This will match 1234A and 123BA, but not 123, 1234C, or 1234ABCD. Filter data = 123?A?. This will match 1234AB and 123BAT, but not 1234A or 123BATS. Filter data = 12??*. This will match 1234, , and 123ABC, but not 12 or 123. Filter data = 123?A*. This will match 1234A, 123BA, and 123BATS, but not 1234 or 1234C. <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> NUL (00 in hex) Any ASCII input in the form of a pair of hex characters. Maximum length: 63 bytes defined. Examples: 41422A = AB* Data [0] = NUL represents string matching disabled. Decode Direction Definition: Serial Cmd: Default: Options: Decode direction is determined by the direction of the output filter. <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> 0 (any direction) 0 = Any Direction 1 = Forward 2 = Reverse MS-890 Industrial Automation Scanner User Manual

253 Database Index Output Format Definition: The index of the database entry that decodes a given symbol must equal this setting for filtering to occur. A setting of 0 allows any database index for this filter entry. Serial Cmd: <K744,filter number,symbology,length,wildcard,placeholder,data,decode direction,database index> Default: 0 Options: 0 = Any Database Index 1 = Database # 1 to n (maximum number of characters in the symbol data) MS-890 Industrial Automation Scanner User Manual 13-13

254 Number of Filters Number of Filters Definition: Serial Cmd: Default: 0 Options: 0 to 12 Number of Filters refers to the number of active output filters. 0 disables all output filters. Any non-zero numeral will enable filtering to be performed using the filter indexes covered by this value. For example, if the number of filters is 1, then only filter index # 1 will be applied. If the number of filters is 2, then only filter index # 1 and filter index # 2 will be applied, etc. <K745,number of filters> MS-890 Industrial Automation Scanner User Manual

255 14 Wiring Box Contents Wiring Box Description Installation Steps Wiring Box Ports Wiring Box PCB with Connectors Mounting Plate This section has instructions for assembling, wiring and using the MS-890 s optional Wiring Box. When this option is selected, the MS-890 and wiring box option are shipped as an assembly. MS-890 Industrial Automation Scanner User Manual 14-1

256 Wiring Box Description Wiring Box Description Note: The wiring box PCB resides inside the wiring box. Ribbon Cable to MS-890 Scanner Portal hole, 3/4 pipe thread (4 places) Bottom mounting plate of wiring box Portal Holes The wiring box has four external portal holes which are standard 3/4 pipe thread. Mounting of the box is with four through holes in flanges that extend out over the ends. Terminal Strip Specifications Wire strip length:.24 (6 mm) Wiring range: AWG Current: 13A maximum 14-2 MS-890 Industrial Automation Scanner User Manual

257 Installation Steps Wiring Box 1. Connect power through the portal holes (see Check Required Hardware on page 1-2). 2. Temporarily apply power to the scanner and confirm that the light next to the input terminal is green and not red. 3. Disconnect power before making the remaining connections. 4. Connect the host and trigger port wires through the portal holes to the appropriate connections. 5. Plug the ribbon cable into the scanner as shown below (apply pressure back and forth on the connector to ensure that it fits inside the receptacle). Ribbon Cable Bottom plate of scanner attaches to top of wiring box Portal holes 3/4 pipe thread (4 places) Wiring box Base mounting plate of wiring box MS-890 Industrial Automation Scanner User Manual 14-3

258 Installation Steps (cont.) Installation Steps (cont.) 6. Attach the scanner to the wiring box with four attached mounting screws in the bottom plate of the scanner, making sure that the gasket is evenly seated. Mounting screws (4 corners of base plate) 7. Mount the wiring box (see Wiring Box Ports on page 14-5) MS-890 Industrial Automation Scanner User Manual

259 RELAY PASS RELA Y PASS RELAY PASS RELAY 2 OUT 2 RELAY 4 PASS 6 RELAY 3 OUT Wiring Box Ports Wiring Box Relay Modules These can be used as an alternative to the 3 optoisolated outputs from the scanner itself. K1, K2, and K3 are module sockets for SM off-the-shelf AC/DC output/relay modules. Note: For relay module kits, use a slim module that does not exceed 0.43 (11 mm) in width. 1.7" (1.1 cm) Locking screw 0.43" (1.1 cm) 3 relay module sockets K REV. 2 K3 J JP1 J J8 K2 J10 J7 1 JP J9 2 JP J J17 MICROSCA N MADE IN U.S.A REV- S/N: GND + TX+ TX RX+ RX GND CHS RELAY 2 OUT RELA Y 3 OUT Jumpers When installing relay modules in K1, K2, and K3, corresponding jumpers (J1, J2, J3) need to be moved. Move jumpers from 3-5 to 1-3 and 4-6 to 2-4 for each relay to be installed (K1, K2, K3). Default jumper positions (using scanner s built-in relay) New jumper position (using pluggable relay) JP JP1 JP2 JP3 K REV. 2 K3 J JP1 J J8 K2 J10 J7 J9 2 1 JP2 J15 JP3 J17 M ICROSCAN MADE IN U.S.A RE V- S/N: GND + TX+ TX RX+ RX GND CHS MS-890 Industrial Automation Scanner User Manual 14-5

260 Wiring Box Ports Relay Terminals Relay terminals 1, 2, and 3 provide output for both internal optoisolated outputs and alternative relay modules that can be installed in modules K1, K2, and K3. Relay1 Output handles discrete outputs from the scanner that will switch up to 100 ma of optoisolated current. +5 VDC Voltage out that can drive a hand held scanner. Maximum current is 5 watts. Input 1 Used to wire a switch to reset latch mode or counters. RS-422/485 Used for multidrop or 422 port. Power VDC Power input port (left side and right side for connectivity convenience). RS-232 Main serial communication port. Aux RS-232 Daisy chain and Auxiliary connections MS-890 Industrial Automation Scanner User Manual

261 Wiring Box New Master Pin Allows you to wire in a switch for New Master Pin. (See Optoisolator Inputs on page A-7.) Trigger Port (NPN) To initiate the read cycle. (See Optoisolator Inputs on page A-7.) Power LED GREEN means the polarity of the input connections is correct; RED means it is reversed. Caution: While the MS-890 scanner has reverse polarity protection built in to its circuitry, the wiring box does not protect external circuits that may already be wired in when power is applied. MS-890 Industrial Automation Scanner User Manual 14-7

262 Wiring Box PCB with Connectors Wiring Box PCB with Connectors 14-8 MS-890 Industrial Automation Scanner User Manual

263 Mounting Plate Wiring Box IB-890 Wiring Box Mounting Plate MS-890 Industrial Automation Scanner User Manual 14-9

264 Mounting Plate MS-890 Industrial Automation Scanner User Manual

265 Appendices Appendix A General Specifications... A-2 Appendix B Electrical Specifications... A-4 Appendix C Serial Configuration Commands... A-9 Appendix D ASCII Table... A-15 Appendix E Embedded Menus... A-17 Appendix F Defaulting / Saving / Initializing... A-18 Appendix G Position Scanner and Symbol... A-21 Appendix H Object Detector... A-22 Appendix I Bar Code Configuration... A-23 Appendix J Test Read Rate... A-25 Appendix K Formulas for Number of Decodes... A-27 Appendix L Operational Tips... A-32 Appendix M Interface Standards... A-33 Appendix N Multidrop Communications... A-34 Appendix O Glossary of Terms... A-39 MS-890 Industrial Automation Scanner User Manual A-1

266 General Specifications Appendix A General Specifications Mechanical Height: 3.5" (88 mm) Width: 5" (127 mm) Depth: 6" (152 mm) Weight: 5 lbs. (2268 g) Environmental Enclosure: IP65 Operating Tempurature: 0 to 50 C (32 to 122 F) Storage Tempurature: -50 to 75 C (-58 to 167 F) Humidity: up to 90% (non-condensing) Emissions and Immunity EN :2001: for Class A products EN :2000+A2:2005 EN :1995+A1:2001 EN : Immunity Laser Light Type: Semiconductor visible laser diode (650 nm nominal) Operating Life: 50, C (77 F) Safety Class: CDRH Class II Indicators Beeper: Good Read, Match/Mismatch, No Read, serial command confirmation LEDS: 1 status, 1 power, 1 Good Read, 5 read performance (representing percentage of good decodes), network/include status, green flash Discrete I/O Trigger, New Master, Input 1: Optoisolated, 5-28V rated (12mA at 24VDC) Outputs (1, 2, 3): Optoisolated, 1-28VDC rated, (I CE 24VDC, current limited by user) Communications MS-890 Dimensions Interface: RS-232, RS , Daisy Chain/Aux Port-capable, dedicated configuration port Symbologies Standard symbologies: Code 39, Code 128, UPC/EAN, Interleaved 2 of 5, Codabar, Code 93, PDF417 Applications Standards: AIAG, GS1-128 Scanning Parameters Scanner Mirror Type: Rotating, single line, 14-faceted Scan Rate: Adjustable from 400 to 1000 scans/second (default = 500 scans/second) Raster Sweep Speed: 1 to 30 sweeps/second Raster Sweep Angle: 30 maximum Scan Width Angle: Typically 60 Pitch Angle: ±50 maximum Skew Angle: ±40 maximum Contrast: 25% min. absolute dark-to-light differential at 650 nm wavelength A-2 MS-890 Industrial Automation Scanner User Manual

267 Appendices Read Ranges Symbol/Narrow Bar Width Read Range 7.5 mil (.190 mm) 10 to 35 (254 to 889 mm) 10 mil (.254 mm) 10 to 44 (254 to 1118 mm) 15 mil (.381 mm) 10 to 74 (254 to 1880 mm) 20 mil (.508 mm) 10 to 90 (254 to 2286 mm) 30 mil (.762 mm) 10 to 100 (254 to 2540 mm) 40 mil (1.020 mm) 10 to 110 (254 to 2794 mm) 50 mil (1.27 mm) 10 to 120 (254 to 3048 mm) FIS Options MS-890 Industrial Automation Scanner Long Range, Stand Alone Version, RS-232/485, 10-28VDC Long Range, Wiring Box-Ready, RS-232/485, 10-28VDC FIS G FIS G Safety Certifications FCC, CDRH, CE, UL/cUL, BSMI, RoHS/WEEE Compliance 2015 Microscan Systems, Inc. All rights reserved. Specifications subject to change. Product specifications are given for typical performance at 25 C (77 F) using grade A labels. Performance characteristics may vary at high temperatures or other environmental extremes. Warranty One year limited warranty on parts and labor. Extended warranty available. MS-890 Industrial Automation Scanner User Manual A-3

268 Electrical Specifications Appendix B Electrical Specifications Maximum Operating Power: 24 Watts Power Requirement: 10 to 28VDC, 200mV p-p max. ripple, 24VDC (typ.) Trigger, New Master, Input 1: 4.5 to 28 VDC (optoisolated) Pin 1 Connectors at the base of the MS-890 unit:: Power Connector Host 25-Pin Connector Trigger Connector 2 1 Pin Caution: Be sure that all cables are connected BEFORE applying power to the system. Always power down BEFORE disconnecting any cables. Power Connector: 3-pin microchange plug 1 Power Ground 2 N/C 3 Power 10 to 28 VDC (in) Caution: If using your own power supply, verify correct connection of power and ground lines. Incorrect connections or use of Chassis ground, Power ground, and Signal ground lines could cause equipment and/or software failure. Trigger Connector: 4-pin microchange socket 1 Power 10 to 28 VDC (out) 2 NPN 3 Ground 4 N/C Programming Connector: 9-pin D-sub plug 2 RX232 3 TX232 5 Signal Ground 9 Boot Mode Note: RS-422 and RS-232 are both enabled by default in the MS-890. A-4 MS-890 Industrial Automation Scanner User Manual

269 Host 25-Pin Connector 25-pin D-sub plug Appendices Pin Host RS-232 Host and Aux RS-232 Host RS-422/485 I/O 1 Chassis Ground a 2 Host TxD Out 3 Host RxD In 4 RTS Aux TxD Out 5 CTS Aux RxD In 6 Output 1 (+) Out 7 Signal Ground b 8 Output 2 (+) Out 9 Trigger ( ) In 10 Trigger (+) In 11 N/C 12 Input 1 (+) In 13 RxD (+) In 14 TxD ( ) Out 15 No Read/Output 3 (+) Out 16 RxD ( ) In 17 Power Ground c 18 Power + 10 to 28 VDC In 19 TxD (+) Out 20 Output 1 ( ) Out 21 Output 2 ( ) Out 22 No Read/Output 3 ( ) Out 23 Input 1 ( ) In 24 New Master ( ) In 25 New Master (+) In a. Chassis Ground: Used to connect chassis body to earth ground only. Not to be used as power or signal return. b. Signal Ground: Used for communication and signal line grounds only. Not to be used as power or chassis return. c. Power Ground: Used for power return only. CAUTION: If using your own power supply, verify correct connection of power and ground lines. Incorrect connections or use of Chassis Ground, Power Ground, and Signal Ground lines could cause equipment failure or software failure. MS-890 Industrial Automation Scanner User Manual A-5

270 Electrical Specifications Optoisolator Outputs Optoisolator circuits can transfer pulses between the scanner and peripherals with no direct connection with the scanner s internal circuitry. However, not every optoisolator configuration provides complete isolation. The following diagrams show both fully optoisolated and non-optoisolated circuits. They are only examples and do not represent all possible wiring configurations. I load =5mA I load =50mA I load =100mA V Out-On 0.7V 0.9V 1.0V t On-Typ 30 µs 20 µs 30 µs t Off-Typ 1000 µs 150 µs 75 µs Output Circuit Examples Fully Optoisolated This circuit is fully optoisolated and is the recommended configuration. It allows the user to apply 1 to 28VDC to the circuit. Caution: The maximum current that can pass through the optoisolator is 100mA. Isolated MS-880 Pwr + Scanner Output Pin 18 Pins 6,8,15 respectively paired with: Pins 20,21,22 Host 1to28V INPUT Pwr Pin 17 Not Optoisolated, Scanner Grounded Non-isolated MS-880 Host Pwr + Pin 18 Scanner Output Pwr Pins 6,8,15 respectively paired with: Pins 20,21,22 Pin 17 INPUT Non-isolated MS-880 Pwr + Scanner Output Pwr Pin 18 Pins 6,8,15 respectively paired with: Pins 20,21,22 Pin 17 Host 1to28V INPUT A-6 MS-890 Industrial Automation Scanner User Manual

271 Optoisolator Inputs Appendices New Master pin and Trigger pulses can be sent to the scanner in the following ways: New Master Pin Inputs Waveform Characteristics: Minimum V I N-HIGH V IN-LO W I / IN-HIG H / I IN-LO W 4.5V / 4 ma 0V / 0 ma Pulse Width min 48 µs Maximum 28V / 33 ma 2V / 2 ma 25-pin Host Connector The following New Master Pin inputs can be fully isolated pulses as PNP or NPN circuits. PNP Circuits Isolated MS-880 V CC Pin 24 of host (+) PNP Master Pin Source +V Signal NPN Circuits NPN Master Pin Isolated MS-880 Source V CC +V Pin 24 of host (+) Pin 25 of host ( ) Pin 25 of host ( ) Signal MS-890 Industrial Automation Scanner User Manual A-7

272 Electrical Specifications Trigger Inputs Waveform Characteristics: Minimum Maximum V IN -L O W IN -HIGH / I IN -L O W 0V /0mA 2V/2mA V IN -HIGH / I 4.5V / 4 ma 28V / 33 ma Pulse W idth min 48 µs Trigger pulses can be sent to the scanner either through the host 25-pin connector or a separate 4-pin trigger connector on the bottom of the scanner. 4-pin Trigger Input Non-isolated MS-880 NPN Trigger Source V CC +5 to 28 V Pin 1 of 4-pin trigger connector. Pwr + +V Pin 2 of 4-pin trigger connector. Pwr Trigger Input Pin 3 of 4-pin trigger connector. Pwr + Signal 25-pin Trigger Input Isolated MS-880 V CC Pin10ofhost(+) Pin 9 of host ( ) PNP Trigger Source +V Signal NPN Trigger Isolated MS-880 Source V CC +V Pin 10 of host (+) Pin 9 of host ( ) Signal PNP Trigger Non-isolated MS-880 V CC Pin 18 (+5 to 28V) Source +V Pin10ofhost(+) Signal Non-isolated MS-880 V CC NPN Trigger Source +V Pin18(+10to28V) Pin 10 of host (+) Pin 9 of host ( ) Pin 17 of host pwr ( ) Pin 9 of host ( ) Pin 17 of host Pwr ( ) Signal A-8 MS-890 Industrial Automation Scanner User Manual

273 Appendices Appendix C Serial Configuration Commands Communications Host Port Parameters Aux Port Parameters Host Protocol Preamble Postamble Response Timeout Intercharacter Delay LRC Auxiliary/Configuration Port System Data ACK/NAK Options Polling Mode Options Daisy Chain Autoconfigure Daisy Chain Scanner ID Read Cycle Trigger Mode Serial Trigger Character External Trigger State End of Read Cycle Good Decode Reads Multisymbol Start Serial Trigger Character End Serial Trigger Character Scan Speed Maximum Element Gain/Tracking AGC Settings Focus Tracking Adjustment Symbologies Narrow Margins/Symbology ID Background Color Code 39 Codabar Interleaved 2 of 5 <K100,baud,parity,stop bits,data bits> <K101,aux port mode,baud,parity,stop bits,data bits,daisy chain ID status,daisy chain ID> <K140,protocol,address> <K141,status,preamble character(s)> <K142,status,postamble character(s)> <K143,timeout setting> <K144,time interval> <K145,status> <K146,aux port status,config port status> <K147,RES,REQ,STX,ETX,ACK,NAK> <K148,RES,REQ,STX,ETX,ACK,NAK> <K150DAISY> <K151,daisy chain scanner,daisy chain scanner ID> <K200,trigger mode,trigger filter duration> <K201,trigger character> <K202,external trigger state> <K220,end of read cycle mode,read cycle timeout> <K221,number before output,mode> <K222,number of symbols,multisymbol separator> <K229,start trigger character> <K230,end trigger character> <K500,scan speed> <K502,max element> <K504,gain,tracking> <K505,AGC sampling status,transition counter> <K508,focus position,zero position> <K520,tracking adjustment> <K450,narrow margins status,symbology identifier status> <K451,background color> <K470,status,check character status,check character output status, large intercharacter gap,fixed symbol length status,fixed symbol length,full ASCII set> <K471,status,start and stop match,start and stop output,large intercharacter gap,fixed symbol length status,fixed symbol length,check character type,check character output> <K472,status,check digit status,check digit output,symbol length #1,symbol length #2,guard bar status,range mode status> MS-890 Industrial Automation Scanner User Manual A-9

274 Serial Configuration Commands UPC/EAN Code 128/EAN-128 Code 93 PDF417 Pharmacode I/O Parameters Serial Verification Beeper Quality Output Symbol Data Output Read Duration Output No Read Message Bad Symbol Message No Symbol Message Input 1 Target/Flood LEDs Database Identifier Output EZ Button EZ Button Modes Trend Analysis Output 1 Trend Analysis Output 2 Trend Analysis Output 3 Diagnostic Output 1 Diagnostic Output 2 Diagnostic Output 3 Configurable Output 1 Configurable Output 2 Configurable Output 3 Matchcode Matchcode Type <K473,UPCstatus,EAN status,supplementals status,separator status,separator character,supplemental type> <K474,Code 128 status,fixed symbol length status,symbol length,ean-128 status,output format,application record separator status,application record separator character,application record brackets status,application record padding status,minimum ratio distance> <K475,status,fixed symbol length status,fixed symbol length> <K476,status,raster sweeps before decode attempt,fixed symbol length status,fixed symbol length,decode at end of read> <K477,status,fixed symbol length status,fixed symbol length,minimum number of bars,bar widths,direction,fixed threshold value> <K701,serial command echo status,serial command beep status, control/hex output> <K702,status> <K704,quality output separator,reads/trigger status,direction output> <K705,status,when to output> <K706,status,separator> <K714,status,message> <K715,status,bad symbol message> <K716,status,no symbol message> <K730,mode,active state> <K750,green flash LED status,green flash duration> <K759,status,separator> <K770,global mode,default on power-on status> <K771,one beep,two beeps,three beeps> <K780,trend analysis mode,number of triggers,number to output on,decodes/trigger threshold> <K781,trend analysis mode,number of triggers,number to output on,decodes/trigger threshold> <K782,trend analysis mode,number of triggers,number to output on,decodes/trigger threshold> <K790,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> <K791,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> <K792,over temperature,service threshold,[unused],laser current high,laser current low,low temperature> <K810,output on,output state,pulse width,output mode> <K811,output on,output state,pulse width,output mode> <K812,output on,output state,pulse width,output mode> <K223,matchcode type,sequential matching,match start position, match length,wild card character,sequence on No Read, sequence on mismatch> A-10 MS-890 Industrial Automation Scanner User Manual

275 Appendices Master Symbol Database Size New Master Pin Configuration Database Sequential Step Enter/Delete Master Symbol Data Request Master Symbol Data Match Replacement Message Mismatch Replacement Message Diagnostics Warning Message Status Lifetime Hours High Temperature Low Temperature Power-On/Resets Counts Hours Since Last Reset Present Operating Temperature Service Message Laser Current Warning Calibration / Configuration Database Optoelectric Control Configuration Database Save Configuration Database Load Configuration Database Request Configuration Database Advanced Calibration Raster/Laser Raster Laser On/Off Output Format Format Extract <K224,number of master symbols> <K225,status> <K227,database index,focus position,gain,tracking,agc mode,raster top,raster bottom,raster speed,laser framing status, laser on position, laser off position,laser power,background color> <K228,sequence step> <K231,master symbol number,master symbol data [no data will delete current master symbol data]> <K231,?>[for all] or <K231,master symbol number?> <K735,status,match replacement message> <K736,status,mismatch replacement message> <K400,warning message status,laser high status,laser low status,novram/reset warning status> <K401,hours10,message> <K402,degrees,message> <K403,degrees,message> <K406?> returns: power-ons,resets (Read-Only) <K407?> returns: hours,minutes (Read-Only) <K408?> returns: current operating temp. (Read-Only) <K409,status,message,time,resolution> <K411,high current status,high current message,low current warning, low current message> <K226,mode,# active database settings,latch on trigger,timer/switch value,control trigger 1 status,control trigger 2 status,control trigger 3 status,database cycles> <K227,database index,focus position,gain,tracking,agc mode,raster top,raster bottom,raster speed,laser framing status, laser on position, laser off position,laser power, background color> <K227+,database index> <K227-,database index> <K227?,database index> or <K227?> for entire database. <K510,auto range,starting focus position,focus step size> <K506,raster status,top offset,bottom offset,raster sweep rate,read cycle on/off> <K700,laser on/off status,laser framing status,laser on position,laser off position, laser power> <K740,output index,start location,length> MS-890 Industrial Automation Scanner User Manual A-11

276 Serial Configuration Commands Format Insert Format Assign Format Status Output Filter Configuration Number of Filters <K741,output index,length,hex string> <K742,symbol number,status> <K743,output format status> <K744,filter number,symbology,length,wildcard,placeholder,data, decode direction,decode direction> <K745,number of filters> A-12 MS-890 Industrial Automation Scanner User Manual

277 Serial Command Format Serial commands are of two types: utility and configuration. Appendices Rules that apply to both utility and configuration commands A less than < and greater than > character enclose the commands. Commands and data are case sensitive. That is, characters must be entered as upper or lower case, as specified. Serial Utility Commands These are sent during operations and are not followed by <A> or <Z>. Serial Configuration K Commands These begin with a single K character followed by a 3-digit numeric character, data fields, and an initializing command, as follows: <Knumeric parameter,data,data,...etc.><initializing command> An initializing command <A> or <Z> may follow the command. A <Z> initializes the scanner s memory and saves for power-on; an <A> initializes the scanner s memory but does not save for power-on. For example, to enable UPC and save the change for power-on, send <K473,1><Z>. To change Baud Rate and reset without saving changes for power-on, send <K100,3><A>. Serial Configuration Command Conventions All data fields (except the last) must be followed by a comma (without a space). All fields preceding a modified field must be included. If there is no change in preceding fields, then commas alone can be entered in these fields. For example, if only the last field in the following command is changing, <K100,4,1,0,0> can be entered as <K100,,,,0>. All fields following a modified field can be omitted. For example, to change Baud Rate only, send <K100,3>. MS-890 Industrial Automation Scanner User Manual A-13

278 Serial Configuration Commands Concatenating Configuration Commands Commands can be concatenated (added together) in a single string or data block. For example, <K145,1><K220,1><K450,1><A> enables LRC, sets End of Read Cycle mode to New Trigger, enables Narrow Margins, and resets the data buffers (without saving the changes for power-on). Serial Command Status Request To ensure that any command was received and accepted, you can send the Show Reader Status command: <?>. The status of a specific serial command can be requested by entering the command followed by a question mark. For example, send <K142?> to request the status of Postamble. Entering Control Characters in Serial Commands To enter control characters within a serial command, hold down the Ctrl key while typing the desired character. Example: To enter a carriage return and line feed (^M^J), enter <K141,1,CNTL-m CNTL-j> Entering Special Characters in Embedded Menus Control Characters Control characters entered on the command line are displayed in the menu as mnemonic characters, such as: <CR><LF><NUL><NUL> Press SP (the space bar) once, then enter the control character by holding down the control key and simultaneously pressing the desired character. For example to define a line feed, press SP, then Control and J simultaneously. It is displayed as ^J on the command line and as <LF> in the menu when the screen is refreshed. To Define a Carriage Return as a Character Press SP, then CR. It is displayed as ^M on the command line and as <CR> in the menu when the screen is refreshed. To Define a Space as a Character Press SP twice. It is displayed as a blank space in the menu when the screen is refreshed. While it appears that nothing has been assigned, the hex value 20 will be sent during data transmission. To Select NUL as the Character Press SP, then a 0. It is displayed as <NUL> in the menu when the screen is refreshed. A-14 MS-890 Industrial Automation Scanner User Manual

279 Appendix D ASCII Table Appendices ASCII Table with Control Characters Dec Hex Mne Ctrl Dec Hex Ch Dec Hex Ch Dec Hex Ch NUL ^@ SP ` SOH ^A 33 21! A a STX ^B B b ETX ^C # C c EOT ^D $ D d ENQ ^E % E e ACK ^F & F f BEL ^G ' G g BS ^H ( H h HT ^I ) I i 10 0A LF ^J 42 2A * 74 4A J 106 6A j 11 0B VT ^K 43 2B B K 107 6B k 12 0C FF ^L 44 2C, 76 4C L 108 6C l 13 0D CR ^M 45 2D D M 109 6D m 14 0E SO ^N 46 2E. 78 4E N 110 6E n 15 0F SI ^O 47 2F / 79 4F O 111 6F o DLE ^P P p DC1 ^Q Q q DC2 ^R R r DC3 ^S S s DC4 ^T T t NAK ^U U u SYN ^V V v ETB ^W W w CAN ^X X x EM ^Y Y y 26 1A SUB ^Z 58 3A : 90 5A Z 122 7A z 27 1B ESC ^[ 59 3B ; 91 5B [ 123 7B { 28 1C FS ^\ 60 3C < 92 5C \ 124 7C 29 1D GS ^] 61 3D = 93 5D ] 125 7D } 30 1E RS ^^ 62 3E > 94 5E ^ 126 7E ~ 31 1F US ^_ 63 3F? 95 5F _ 127 7F D MS-890 Industrial Automation Scanner User Manual A-15

280 ASCII Table Communications Protocol Command Table Protocol Command (Mnemonic displayed on menu) Control Characters (Entered in menu or serial command) Hex Value Effect of Command RES ^D 04 Reset REQ ^E 05 Request EOT ^D 04 Reset STX ^B 02 Start of Text ETX ^C 03 End of Text ACK ^F 06 Acknowledge NAK ^U 15 Negative Acknowledge XON ^Q 11 Begin Transmission XOFF ^S 13 Stop Transmission A-16 MS-890 Industrial Automation Scanner User Manual

281 Appendix E Embedded Menus Appendices In addition to ESP, you can also use a communications menu such as HyperTerminal to establish communication with Microscan s embedded menus With your host connected to the 9-pin configuration port, set your host communications settings as follows: 57.6K baud, 8 Data Bits, 1 Stop Bits, and None Parity. OR, with your host connected to the 25-pin configuration port, set your host communications settings as follows: 9600, 7, 1, and Even. 13. Set Flow Control to None. 14. Make the communications port selection. (Usually COM 1 or COM 2 for desktops and COM 1 for laptops.) 15. Upon connection, send a <D> command to bring up the main menu. Note: The 9-pin configuration port settings are fixed. Important: To receive symbol data through the 9-pin configuration port, you must enable the port with the following command: <K146,,1>. 16. Press the return key (CR) to view the communications menu. Menu navigation commands are case sensitive. Use the space bar or N to advance to the next item, CR (return key) to select a highlighted item, B to return to the previous item, M to return to the previous menu, and ESC to return to the Main menu or to exit the program. When exiting the program, you will be prompted to save your active settings for power up (Y or N). Typing Y will be equivalent to saving with a <Z> command. 1. If you are using HyperTerminal, you may find that the initial screen is unviewable when you call up the program with the <D> command. If this occurs, simply exit the embedded menu with a ESC, E, and N sequence and repeat the <D> command. MS-890 Industrial Automation Scanner User Manual A-17

282 Defaulting/Saving/Initializing Appendix F Defaulting/Saving/Initializing Active Memory is where the scanner s settings are stored during current use and are initialized by an <A> command. Microscan Defaults are where the scanner s default application/boot programs are stored. They can only be changed by changing the application/boot codes. 1 User-Saved Settings are where user-defined settings are saved for power-on. Defaulting Defaulting occurs when default settings (either Microscan or user-saved) are restored. Defaulting might be necessary if you have to make temporary changes, communications between the scanner and another device are lost or interrupted, or you are using incompatible equipment (for example, a terminal that is set at 9600 baud communicating with a scanner that is set at 38.4K baud). Restore User-Saved Settings to Active Memory Restores user-defined settings to active memory. Initializes serial configuration commands in active memory and resets counters to zero. Restore User-Saved Settings to Active Memory by Serial Command Send <An> command to the scanner. Note: There is no equivalent ESP command. Restore Microscan Defaults to Active Memory Restores Microscan defaults to active memory. Initializes serial configuration commands in active memory and resets counters to zero. Does not save settings for power-on. Restore Microscan Defaults to Active Memory by ESP Right-click in the configuration window and select Default All ESP Settings. 1. See your Microscan sales representative to access the latest application code. A-18 MS-890 Industrial Automation Scanner User Manual

283 Appendices Restore Microscan Defaults to Active Memory and Power-On Caution: Defaulting the scanner to Microscan default settings will overwrite user-saved settings. Restores Microscan defaults to memory. Restores Microscan defaults to user-saved settings for power-on. Initializes serial configuration commands in active memory and resets counters to zero. Restore Microscan Defaults to Active Memory and Power-On Send <Zd> command to the scanner. Restore Microscan Defaults to Active Memory and Power-On by ESP 1. Right-click in the configuration window and select Default All ESP Settings. 2. Right-click and select Save to Reader and Send and Save. Restore Microscan Defaults by Hardware Default There is no hardware default for the MS-890. Default commands can be entered from any of the host connectors. Since the default communications settings on the 9-pin connector are fixed, you can always send a default the scanner through this port with a software command. MS-890 Industrial Automation Scanner User Manual A-19

284 Defaulting/Saving/Initializing Saving Power-On settings are those that are saved by a <Z> command and are loaded into active memory whenever power to the scanner is recycled. Save Active Settings (Except Factory) for Power-On Initializes serial configuration commands into active memory and resets counters to zero. Saves all current settings except factory settings to user-saved settings for power-on. Save Active Settings (Except Factory) for Power-On by Serial Command Send <Z> command to the scanner. Save Active Settings (Except Factory) for Power-On by ESP Right-click in the configuration window and select Save to Reader, then Send and Save. Initializing Initializing occurs whenever any command or set of commands is implemented. Initializing is a part of all save and default functions. It is also used as a follow-on to implement serial configuration commands. Initializes serial configuration commands into active memory and resets counters to zero. Does not save settings for power-on. Initializing by Serial Command Send <A> after a serial configuration command or a string of serial configuration commands. For example: <K141,1><A>. Initializing by ESP Right-click in the configuration window and select Save to Reader, Send No Save. This will initialize all serial configuration changes that have been made in the current ESP session. Note: Allow a 1.5 second delay after sending the <A> command before resuming communications. Loss of Communications Making changes to communications with the host such as Baud Rate, Parity, Stop Bits, LRC, etc. without corresponding changes in linked device(s) can result in the loss of menu access through the 25-pin port and wiring box connections. If this should occur, connect the scanner to the 9-pin port and set your host communications settings as follows: 57.6K baud, 8 Data Bits, 1 Stop Bits, and None Parity. These settings for this port are fixed and cannot be changed.you should restore the scanner s defaults.if you wish to return to the 25-pin host port, you ll first need to change the scanner s communications settings by sending: <K100,4,1,0,0><Z>. A-20 MS-890 Industrial Automation Scanner User Manual

285 Appendices Appendix G Position Scanner and Symbol In positioning the scanner in relation to the symbols being scanner, consider the following: Position the scanner in a place devoid of sunlight, bright lights, or laser light from other sources. Avoid excessive tilt, skew, or pitch. Maximum tilt is determined by symbol characteristics and the number of decodes required. Maximum skew is ±40 ; maximum pitch is ±50. 1 Pitch symbol (or scanner) slightly to avoid specular reflection, the return of direct, non-diffused light. Specular reflection is avoided by pitching symbols at least 5 plus or minus from a line perpendicular to the default position of the Raster Bottom and Raster Top. 2 Note: Another way to avoid specular reflection is to skew the scanner slightly in relation to the symbol. Scanner Position 1. Maximum tilt is determined by symbol characteristics and number of decodes required. 2. The specular reflection zone is a narrow zone straight out from the scanner in which direct reflected light from a symbol can distort the scanner s ability to distinguish bars from spaces. MS-890 Industrial Automation Scanner User Manual A-21

286 Object Detector Appendix H Object Detector In a typical operation, a scanner will wait for symbol data only during a triggered read cycle. A read cycle is initiated by a trigger and can be in the form of a serial command from the host (internal trigger) or a signal from an object detector (external trigger). When an object detector (also called a sensor, package detector, etc.) is used, it is set up so that its beam will bounce off the approaching object and the resulting pulse will be sent to the scanner to begin the read cycle. Typically, a detector is positioned so that it will detect the presence of an object before its symbol can be scanned. An object detector is mounted in almost any position relative to the object as long as: (1) the object passes within range of the detector and (2) direct or reflected light from the detector does not interfere with the scanner s reception. As the item continues to move down the line, its symbol moves into the scanner beam and is read by the scanner. The drawing below shows a symbol in the picket fence direction with the object detector positioned so as not to cause interference. Object Detector Operation A-22 MS-890 Industrial Automation Scanner User Manual

287 Appendix I Bar Code Configuration Appendices You can configure the MS-890 by presenting Code 128 symbols encoded with serial commands. Note: Your scanner does not need to be enabled for Code 128 in order to enter Bar Code Configuration. Entering Bar Code Configuration The symbol used to enter configuration is the 7-character code 128 symbol shown below. It is not required that the scanner be configured to read code 128 symbols to read this start symbol or the following configuration symbols. To set up Bar Code Configuration: 1. Put the scanner in a read cycle mode. 2. Place a special Code 128 configuration Start symbol (provided below) in the scanner s field of view. If the scanner is able to read the Start symbol, it will begin to beep and the performance LEDs will activate. 3. When the scanner starts to beep, remove the configuration symbol from the scanner s field of view. The scanner is now in Bar Code Configuration mode. During Bar Code Configuration mode, the LEDs will illuminate in a sequential pattern to indicate that the scanner is ready to be configured. You can create your own start symbol by encoding the following character sequence in a Code 128 symbol: FNC4 <_CFG> MS-890 Industrial Automation Scanner User Manual A-23

288 Bar Code Configuration Using Configuration Symbols Once in Bar Code Configuration mode, serial command data encoded in Code 128 symbols is decoded by the scanner as serial input. Configuration symbols must meet the following conditions: 1. The only valid symbology for Bar Code Configuration is Code Symbol data may contain more than one command, but individual symbols must be presented individually. This is because only the first symbol in a read cycle will be used as a possible configuration symbol. A symbol that is presented to the scanner must be read 25 times consecutively to be used as a valid symbol. Once this is done, the scanner will interpret the symbol data in the same fashion as it interprets serial data. 3. Any valid command may be encoded in Code 128 symbols, including operational commands. Because the data is treated like serial input, multiple symbols may be used to represent one command as long as the symbols are presented individually and in the correct order. 4. Read Rate commands may also be used to enter Read Rate from Bar Code Configuration mode. 5. When in Read Rate, the scanner will read the symbologies that were enabled prior to entering Bar Code Configuration mode. However, the scanner will read a <J> in Code 128 regardless of the current enable/disable state of Code 128. Once the <J> is issued, the scanner will exit both Read Rate and Bar Code Configuration mode. To exit Read Rate and remain in Bar Code Configuration mode, present the start symbol once again. Symbols decoded during Read Rate will not configure the scanner. Scan the symbol shown to the right to start a Read Rate test. Exiting Bar Code Configuration There are multiple ways of exiting Bar Code Configuration. The first way is simply to decode a symbol encoded with the <J> command, or to enter a <J> command from a terminal. The scanner will beep when exiting Bar Code Configuration in response to a <J> command. Any command that executes a software reset will also end Bar Code Configuration mode. These commands include the Save family as well as the Reset family (<Z>, <Zc>, <A>, <Arc>). To end the Read Rate test and Bar Code Configuration mode, scan this symbol: Configuration changes will remain in effect, as would changes made by using serial commands or ESP. A-24 MS-890 Industrial Automation Scanner User Manual

289 Appendix J Test Read Rate Appendices Test Read Rate by Bar Code Configuration You can enter a Read Rate test by scanning the following symbols: Enable Bar Code Configuration (Also activates the scanner s read performance LEDs.) Enable All Symbologies Start Read Rate Test End Read Rate Test and Disable Bar Code Configuration Test Read Rate by Serial Command (Static Symbol) 1. Position a stationary symbol in front of a functioning scanner at the scan distance used in your application. 2. Set for single scan line scanning (Raster Top setting equal to Raster Bottom). 3. Enter a <C> command to see the decodes per second. The decode rate is the number of decoded scans per total number of scan. It will appear at the beginning of the data strings. Note: You can also enter a <Cp> command to see the percentage of decodes per scans. 4. Make a note of the decode rate. You will need this when calculating the number of decodes (see Appendix K, Formulas for Number of Decodes on page A-27). 5. End the test by sending the <J> command. MS-890 Industrial Automation Scanner User Manual A-25

290 Test Read Rate Test Read Rate by ESP See Read Rate in Chapter 12, Utilities. Test Read Rate with a Moving Symbol Before testing with a moving symbol, it is highly recommended that you calculate the expected number of decodes by using the formulas in Appendix K, Formulas for Number of Decodes on page A-27. Once you ve mounted the scanner, established a good read rate with a stationary symbol, and calculated the number of decodes for your symbol speed, you can begin decoding with moving symbols. Number of Decodes To ensure reliable scanning, you need to apply a minimum of five decodes to each symbol. This means that all variables, symbol speed, read range, etc. are significant. Note: Variations between symbols are common. For this reason, the greater the number of sample symbols tested, the more likely you are to achieve optimum decode rates. In general, the number of decodes of a given symbol can be increased by: Increasing symbol height Decreasing symbol length Increasing scan rate (spinning mirror speed) Slowing symbol speed Decreasing raster sweep rate Decreasing raster height A-26 MS-890 Industrial Automation Scanner User Manual

291 Appendices Appendix K Formulas for Number of Decodes To ensure reliable scanning, apply a minimum of five decodes to each symbol. Use the formulas below to calculate the number of decodes that your symbol will receive. If the number of decodes you derive from one of these calculations is less than the minimum for your application, plug in the minimum number of decodes (5) and solve for another parameter that might be changed, such as symbol speed or scans per second. Note: While the formulas given here solve for the predicted number of decodes, you may also use the formulas to solve for other parameters that might be changed, such as symbol speed, symbol length, etc. Single Line Ladder Calculation Ladder scanning is seldom done with raster scanning unless the raster is set for single scan line scanning (Top Offset setting equal to Bottom Offset) or symbols are presented as stop-and-go. For single scan line ladder scanning, use the following formula: 1 ND (Number of Decodes) is the number of decodes that a Single Line Ladder given symbol can be expected to achieve in a given Orientation application. SH (Symbol Height) is a measurement of the height of individual bars. SS (Symbol Speed) is the distance per second that a symbol moves through the scan. DR (Decode Rate) is the number of scans per second that a given symbol receives. Example: 1. The -3 component in the formula is included to allow for AGC acquisition, an incomplete first scan, and an incomplete last scan. This applies only if the number inside the parentheses equals 4 or more. If the number equals 3, then only subtract 2 to derive 1 good scan. MS-890 Industrial Automation Scanner User Manual A-27

292 Formulas for Number of Decodes Raster Picket Fence Calculation For raster picket fence scanning, the number of decodes (ND) that can be applied to a given symbol can be calculated once the sweep rate (SPS) is known. Sweep Rate (Sweeps per Second) Sweep rate is the number of raster sweeps (up or down) that occur per second and can be set in ESP. Since the sweep rate cannot exceed 30, you first need to ensure that your application can achieve this by solving for sweep rate (SPS). The sweep rate should generally be set as low as possible in order to maximize the number of scans on a given symbol. The formula for finding Sweep Rate (SPS) is as follows: Raster Picket Fence Orientation SPS = Sweeps per Second, the number of passes, up or down, that are described by the arc of the raster mirror. SS = Symbol Speed, the inches per second that a symbol moves through the scan. SW = Scan Width, the width across the scan beam, at a given distance from the scanner, in which a symbol can be read (picket fence formula only). SL = Symbol Length, the length of the longest printed symbol to be read plus the length of the quiet zones (picket fence formula only). Example: Important: The maximum sweep rate that your can set the scanner to is 30. If your solution is greater than 30, you must change another parameter such as symbol speed, etc., and recalculate. Since SPS can only be entered into the software as whole numbers, round off fractions of SPS to the next higher number, for example enter 0.4 as 1 and 3.5 as 4. In setting up the scanner, raster height depends on the raster arc and the symbol distance (range) from the scanner. Both the top offset and bottom offsets can be adjusted independently in 255 increments and the resulting arc can vary from 0 to 30. (See Chapter 10, Raster/Laser.) A-28 MS-890 Industrial Automation Scanner User Manual

293 Number of Decodes Appendices Note: Because adjustable raster sweeps and scan speeds cannot be synchronized, some variation in raster height should be anticipated. Number of decodes (ND) for a raster picket fence symbol is calculated by the following formula: Example: ND = Number of Decodes (total applied to each symbol) SH = Symbol Height DR = Decode Rate RH = Raster Height SPS = Sweeps per Second Raster Height If raster arc (in degrees) and symbol range are known, raster height can be derived by the following formula, where Ø is raster arc in degrees: 1 Raster Arc If raster height and symbol range are known, then raster arc Ø can be derived by using the following formula where RH is raster height: Note: Raster arc is not presented in degrees in ESP. To convert to degrees, add the Top Offset to the Bottom Offset and subtract the sum from 255. Enter this as the offset in the following formula: MS-890 In dustrial Automation Scanner User Manual A-29

294 Formulas for Number of Decodes Single Line Picket Fence Calculation For single scan line picket fence scanning (Top Offset setting equal to Bottom Offset), use the following fomula: ND = Number of Decodes (total applied to each symbol) SW = Scan Width SL = Symbol Length SS = Symbol Speed DR = Decode Rate Single Line Picket Fence Orientation Example: Angled Picket Fence Calculation The number of complete scans for angled picket fence is calculated the same as that for picket fence, with the exception that the scan width is shortened in proportion to scan tilt. Angled Picket Fence Orientation A-30 MS-890 Industrial Automation Scanner User Manual

295 Appendices Improving Decode Rate After changing any of the parameters described in this section, recalculate the number of decodes. Scan Rate Scan rate is a function of motor speed and is adjustable. A slower scan rate may allow greater symbol range and/or higher decode rates, but at the cost of fewer scans per symbol and scan width. Range Adjusting the symbol s range, if possible, is one of the quickest and most effective ways to improve decode rates. However, in some applications you may need to select a less than optimum range, or one that is beyond the fringes of the ranges. Scan Width Increasing scan width will increase the number of scans in a picket fence oriented application. Scan width is linked with scan range and changing one will usually require a change in the other. Symbol Speed Applies to both picket fence and ladder oriented symbols. If your application allows it, slowing symbol speed (the time in seconds that a symbol is fully within the scan width of the scanner) is an effective way to increase the number of decodes. Raster Height When using the raster features, you can increase the decode rate by decreasing the height of the raster image. Raster Sweep Rate Slowing the number of sweeps per second to the minimum needed will result in more scan lines passing over the symbol and a higher decode rate. Laser Framing Narrowing the laser frame may not increase the decode rate, but it will minimize the opportunity of extraneous reads. Symbol Dimensions, Symbol Density, and Symbol Ratio Not usually an option in most applications, but changes to symbol parameters can affect number of decodes calculations and possibly decode rates. If your application allows it, shortening the length of a picket fence symbol means the symbol will be in the scan range longer and hence receive a greater number of scans. Increasing the height of a ladder symbol means it will receive more scans. Changing symbol density and/or symbol ratio is another way ranges, decode rates, etc. can be altered. Gain and Tracking These adjustments, typically made by qualified technicians, are referenced in the Scanner Setup menu (see Defaulting/Saving/Initializing on page A-18). Changes to tracking will generally have a limited affect on decode rates. MS-890 Industrial Automation Scanner User Manual A-31

296 Operational Tips Appendix L Operational Tips Do: Check inputs (symbol speed, length, height, etc.) to ensure the desired number of decodes per symbol. For optimum decodes, mount scanner so that your symbols pass through the center of the depth-of-field (minimum/maximum range). You find the center by moving your symbol in and out during a read rate test. Avoid excessive tilt, pitch, and skew of the symbol. Check the symbol for readability by doing a decode rate test. If there is any question about the symbol's readability, contact your Microscan sales representative. After changing any parameter that might affect decode rate, repeat decode rate test. Clean the scanner window with a clean, dry cotton swab or cotton cloth on a regular basis. Do Not: Aim the scanner into direct light or sunlight. Aim the scanner into an external object detector or other light-emitting device. Obstruct the scanner window with mounting hardware or other objects. Connect chassis of scanner and host to different ground potentials. Operate the scanner in excessive temperature environments. A-32 MS-890 Industrial Automation Scanner User Manual

297 Appendix M Interface Standards Appendices Interface Standards, established by the Electronic Industries Association (EIA), specify such things as the signaling voltage levels, maximum cable lengths, and number of drivers. With Microscan devices, selection of interface is made by pin assignment and, in the case of the host communications, by software switching between RS-232 and RS-422. Microscan devices use RS-232, RS-422, and RS-485 multidrop. RS-232 RS-232 defines an interface between two devices such as, for example, the scanner and host. It differs from the other interfaces by dedicating individual pins to specific functions and by requiring both devices to share a common ground line. Since both device chassis are connected to a common ground, a ground loop potential and the possibility of noise interference exists. Therefore cable lengths are limited to a maximum of 50 feet (19.7m). Despite being the most limited, this interface is used frequently because of the large installed base of RS-232 equipment. RS-422 RS-422, unlike RS-232, measures signals deferentially; that is, the receiver looks at the potentials between the two receive (or transmit) wires rather than the potential between signal and ground. As a result, cables, if shielded, can be up to 4000 feet (1219m) in length. Like RS-232, RS-422 communication is designed for only two devices on a single line and must have a common ground. It can be used wherever RS-232 is used. RS-485 RS-485, like RS-422, can transmit up to 4000 feet (1219 m) using differential voltages but unlike RS-422, its transmitters are turned off until a request for data is received from the host. RS-485 is used exclusively in Multidrop protocol. MS-890 Industrial Automation Scanner User Manual A-33

298 Multidrop Communications Appendix N Multidrop Communications This appendix describes the rules for setting up a concentrator or controller to communicate with a scanner in standard Multidrop protocol. The diagram to the right shows a typical Multidrop network in which 1 to 50 scanners can communicate with a host via an intermediary device, a concentrator, or a controller. Host Concentrator Polled Protocol Multidrop ONLY RS-485 Interface Multidrop Scanner 01 Scanner 02 Scanner 03 Configure Scanner for Multidrop 1. With the scanner connected to the host, Retrieve Reader Settings. 2. Select Multidrop in the Protocol configuration menu. You will see the following message: Important: You must change your preamble and postamble characters so that they are not CR or NUL. This allows data to move through the concentrator without interference. 3. Click OK. 4. Next, go to Preamble Characters (still in the Protocol menu) and double-click on Characters. 5. This will open up an ASCII character table. Select any character but CR. 6. Repeat the above process for Postamble. 7. Check the multidrop address. Enter a number from 01 to Right-click in the window and select Save to Reader and Send and Save. 9. Your scanner is now in Multidrop. From here on, you will need to use the concentrator to relay commands and data between the scanner or scanners and the host. 10. Move on to Connect to Scanner via Concentrator. A-34 MS-890 Industrial Automation Scanner User Manual

299 Connect to Scanner via Concentrator Appendices You will need a multidrop concentrator and the required power supplies and cabling to communicate with your scanner(s). 1. From the Communications dropdown menu in the menu toolbar, select Configure Multidrop. The Multidrop Settings dialog will appear. 2. If necessary, change the default address to match the address of your multidropped scanner and click OK. If the host serial port is not connected in ESP, you will see the following popup message: ESP is not currently connected to the multidrop concentrator. Do you wish to establish a connection now? 3. Click Yes. 4. The Connection Settings dialog will appear. Notice that the Force Connect option is checked. Do not change this. 5. Select the concentrator s host port communications settings. When you click Connect, you will be connecting to your concentrator, which can then relay commands to the scanner whose address was set in the Multidrop Settings dialog. 6. Click Connect. You should see the CONNECTED message in green at the bottom of the window along with the scanner s Multidrop address. 7. Click Retrieve Reader Settings to upload the scanner s configuration. If upload fails, return to the Connection Settings dialog and make the necessary parameter changes. 8. Follow the same procedure for connecting other scanners to your multidrop network. MS-890 Industrial Automation Scanner User Manual A-35