Functional Unit [hex] DTC Severity [hex] above maximum 9 V F SE. below minimum 6.5 V F SE

Transcription

1 ANNEX A description B.1 definitions For each defined by [ISO ], the following table provides its description, severity, functional unit, high/middle/low bytes, sub code and status. The status column specifies the state of the warning lamp associated to the : - when the status value is AF, then the warning lamp is ON, - when the status value is 2F, then the warning lamp is OFF. Each may be associated to an event/fault defined by [AN1B], see Annex Virhe. Viitteen lähdettä ei löytynyt.. Some events/faults are not generated when the tachograph is in workshop mode. For such cases, the warning lamp is OFF while the corresponding is active. The status field of such s is marked with *. The following table also specifes the field in the TCO1 message on CAN associated with each (see [ISO ]). This parameter may take the following values : TP = Tachograph performance, HI = Handling Information, SE = System Event. N IS Sensor power supply MS power supply and data link signal above maximum 9 V F SE below minimum 6.5 V F SE no signal 5.5 V AF * SE

2 - N IS Tachograph power supply VU power supply above maximum 36 V F SE below minimum 10.5 V : threshold under which printer and F SE card readers motors don t operate no signal 5.5 V AF * SE 3. Card 1 error The inserted card is not a tachograph AF SE card (when Tachograph Directory File is selected). Fault of the inserted card detected : AF * SE - Error code on Directory File/Elementary File - Data integrity problem Card authentication error AF * SE CardValidityBegin later than card AF SE insertion date Current Date is later as the AF SE CardExpiryDate If certification date or the selecting AF SE public key date is expired 4. Card 2 error The inserted card is not a tachograph card (when Tachograph Directory File is selected) AF SE Fault of the inserted card detected : AF * SE - Error code on Directory File/Elementary File - Data integrity problem Card authentication error AF * SE CardValidityBegin later than card AF SE insertion date

3 7. Printer paper out, no paper Current Date is later as the CardExpiryDate If certification date or the selecting public key date is expired No more paper in printer, or printer door open AF SE AF SE F HI 8. No speed signal from sensor no signal 9. Invalid speed signal or data link error invalid signal 10. Speed sensor Recording : no data link signal no signal 11. Sensor / Tachograph signature mismatch MS error : No Speed signal but Pulsecounter information from MS-DATA MS data error : Wrong ACK, Bad response, Pulse counter incoherent between MS and VU AF TP Wrong ACK AF TP Bad response AF TP Speed signal received by the VU and pulse counter incoherent between MS and VU AF TP MS data error : No ACK AF TP MS Security breach attempt - VU Authentication error Authentication error read from the MS AF * TP Failed MS authentication by the VU AF * TP 13. Time / Date error Time/Date error (RTC-Communication error) AF * TP

4 Real Time clock battery empty (Detection only after re-connection of VBAT) AF * TP 19. No ignition, but speed pulses present No ignition, but speed pulses present F HI 20. CAN, internal error General fault (emission) A F SE General fault (reception) A F SE 21. CAN, bus off Bus CAN off B F SE 22. CAN communication instrument <-> Recording no signal 23. Program memory, checksum error No communication with the instrument cluster (reset message time-out) Recording equipment faults : VU integrity check by software signature verification by the Security Component F SE C AF * TP 24. Calibration memory, read/ write error VU Security breach attempt : Integrity error on stored user data D AF * TP 25. Calibration error Calibration error : - All calibration operations have not been performed D F TP

5 - NextCalibrationDate is passed, except if VU was not activated D F TP 26. Printer error Printer faults : Overtemperature AF * TP No communication with printer AF * TP 27. Card reader 1 error VU : no communication AF TP with inserted card The card does not answer at all (card inserted, mechanical contact, no communication : no Answer To Reset card upside down or silent) AF TP 28. Card reader 2 error VU : no communication with inserted card The card does not answer at all (card inserted, mechanical contact, no communication : no Answer To Reset card upside down or silent) AF TP AF TP 29. Buttons / KBD error Recording equipment faults : VU Keyboard (One or more buttons are permanetly active) F AF * TP 30. Error in Internal display Data communication error with display AF * TP

6 31. Internal error in sensor MS Error - MS Security breach attempt : Stored Data integrity error - MS comunicates correctly, but does not send any response to instructions 70/10 (e.g. non paired sensor) AF * TP 32. Error pin B5 Recording equipment faults : VU Wake up input : no Short Circuit / Open Circuit fault detection 33. Error pin B6 Recording equipment faults : VU AF * TP AF * TP AF * TP 34. Speed pulse output Recording (B7) Recording equipment faults : VU AF * TP AF * TP

7 35. Error pin B8 Recording equipment faults : VU 36. Error pin C1 Recording equipment faults : VU 37. Error pin C2 Recording equipment faults : VU Engine speed sensor or RS232 Ground (GND) : no Short 38. Error pin C3 Recording equipment faults : VU Engine speed sensor signal input or RS232 (Rx) : no Short Circuit / Open Circuit Detection AF * TP AF * TP AF * TP AF * TP AF * TP AF * TP

8 39. Error pin C4 Recording equipment faults : VU Engine speed sensor signal input or RS232 (Tx) : no Short 40. Error pin C5 Recording equipment faults : VU CAN1_H : no Short 41. Error pin C6 Recording equipment faults : VU CAN1 GND : no Short 42. Error pin C7 Recording equipment faults : VU CAN1_L : no Short Circuit / Open Circuit Detection 43. Error pin C8 Recording equipment faults : VU Internal resistor to CAN1_H : no Short Circuit / Open Circuit Detection. 44. Error pin D1 Recording equipment faults : VU AF * TP AF * TP AF * TP AF * TP AF * TP AF * TP AF * TP

9 45. Error pin D2 Recording equipment faults : VU 46. Error pin D3 Recording equipment faults : VU CAN2 GND : no Short Circuit / Open Circuit Detection. 47. Error pin D4 Recording equipment faults : VU Short Circuit detection on the warning output 48. Error pin D5 Recording equipment faults : VU CAN2_L : no Short 49. Error pin D6 Recording equipment faults : VU AF * TP AF * TP A AF * TP B AF * TP C AF * TP D AF * TP

10 D AF * TP 50. Error pin D7 Recording equipment faults : VU K line : no Short 51. Error pin D8 Recording equipment faults : VU K line : no Short Circuit / Open Circuit Detection E AF * TP F AF * TP * 52. Recording, internal error Communication with the security component (time-out) VU Security breach attempt : Stored user data integrity error AF * TP AF * TP 53. Driving without card Driving without an appropriate card AF HI