Electronic Indicator

Transcription

1 TIR ABS CR /MM Electronic Indicator Operating Manual Analog Display Analog Visual Display Incremental Measuring Mode SPC Cables USB, MTI, RS232 Measuring System in English or Metric Travel Reverse Auto off Rotating Bezel Internal and External Serial Numbers T.I.R. with Low & High Storage Recall Power with Batteries Power by AC Jack or Data Output Programmable Lock Combination User Tolerance Settings (high & low) Up to 4 User Changeable Resolutions Inch/Metric Display Conversion Maximum Reading Hold Display/Freeze Reading Hold Minimum Reading Hold Absolute/Preset Measuring Mode

2 TABLE OF CONTENTS Power Source Options...3 Button Functions...4 Summary Chart For Analog Button Actions...5 Display-Operating Prompts & Conditions...6 Power On/Off...7 Auto-Off Toggle...7 Travel Reverse Toggle...7 Change Units...8 Hold Mode...8 Tolerance On/Off...9 Tolerance Settings...9 Set High Tolerance Number...10 Set Low Tolerance Number...10 Set Absolute Number Lock Toggle...12 Lock Combination...12 Reset to Factory Defaults...13 Verify Data I/O Type...13 Set Gage Resolution...14 Display Setup Mode...14 TIR Mode...15 Custom Applications

3 CHOICE OF THREE POWER SOURCES 1. Batteries The lithium battery used in this indicator is an IEC standard, type CR2450. The indicators are shipped with the batteries installed. Note: This indicator has an AUTO-OFF feature to conserve battery life. After 10 minutes of no activity (no key presses or spindle movement), the gage will turn itself off. This feature may be disabled if continuous operation is desired; see AUTO-OFF On/Off instructions in this book. Installing Batteries Using a narrow screwdriver, gently pry under the tab on the left side of plastic bezel and slide out the battery tray as you turn the indicator face side down. Insert two batteries, + side up, into tray cavities, then slide the tray back into its bezel slot, taking care that the batteries stay in proper position. 2. AC Adapter First insert the mini-plug into the socket on the lower right side of the bezel, then plug the adapter into a wall outlet. 3. Data I/O Connector Power also may be provided through the data I/O connector, for special fixturing or applications where the indicator is integrated with another piece of equipment. A ripplefree 5 VDC regulated voltage source is required. 3

4 BUTTON FUNCTIONS Key OFF/MODE ON/CLR /MM Function Controlled Off turns indicator off MODE controls absolute numbers & display setup On turns indicator on CLR resets the Lock Toggle, Data I/O Type, gage resolution, and Display setup mode Allows you to hold the value on the display according to the specified Mode (MAX, M, FRZ) Controls the display units (default is English) Controls the Lock Toggle, Data I/O Type, gage resolution, Travel Reverse, Auto Off and Display setup mode Controls Low, High and On tolerance settings 4

5 SUMMARY CHART FOR ANALOG BUTTON ACTIONS Button actions occur on the press of the button in most cases. Some button presses will have the action occur on the release of the button press. For example, when the ON/CLR button is used to clear the display, the action is to happen on the release of the button. When the ON/CLR button is used as the 2nd function in a sequence of button pushes, the action can be on the press of the button. Whenever a button press requires a continuous press to scroll through some selection process, the action of the button is on the release of the button. BUTTON /MM FUNCTION PRIMARY SUBSIDIARY FUNCTION 3RD FUNCTION Toggle on/off Toggles between inches, millimeters Enables functions Select hold type (MAX, M, FRZ) press and hold to step through selection Apply function Move function Toggles travel reverse (normal/reverse) Enter resolution select process* (, ON/CLR, ) Resets to factory default settings (, ON/CLR, /MM) Verify data out put (, ON/CLR, ) Toggles tolerance on or off Select high or low to view or set numbers* Change function Enter preset setting process* Toggles lock on and off; press and release (, ON/CLR, ) Enters user lock combination setting mode (press and hold to access setting mode)* ON/CLR Turn gage on Clears/resets display to 0 or spindle position, or abs number or abs +/- spindle position Enables 3RD function OFF/MODE Turns gage off Select measurement mode (CR, ABS, TIR) press and hold to step through selection Toggles auto-off on and off Enter display selection style* (, ON/CLR, OFF/MODE) * Note: apply, move and change are automatically active when in preset, lock and tolerance setting modes. Apply and change are automatically active when in resolution set mode. 5

6 DISPLAY-OPERATG PROMPTS & CONDITIONS Indicator is in preset number setting function for ABS or tolerance high or low preset numbers Indicator ready for 2nd or 3rd function key entry sequences AUTO-off is enabled to conserve battery life. Analog display Displays for English (inch), or MM for Metric Measuring Units. Negative reading. No sign is displayed for positive readings. Features and presets numbers are locked For Total Indicator Runout (TIR), travel direction is ignored. Peak (MAX) and valley (M) values are available. FRZ M MAX SET /MM ON/CLR TIR ABS CR OFF/MODE LOW HIGH ON Menu selection items under hold or tolerance areas MM Travel reversed, display counts down with spindle movement for CR and ABS measurement modes. Display counts up with inward spindle movement for CR and ABS measurement modes. 6

7 OPERATG STRUCTIONS Power On/Off To turn the unit on, press ON/CLR. To turn off, press OFF/MODE. Auto-Off Toggle To turn the Auto-Off function on or off, press the button ( ICON should appear on the display). Press the OFF/MODE. An hour glass appears at the left side of the display if AUTO OFF is active. If AUTO OFF is active the indicator will power off in 10 minutes with no activity (button press or spindle movement). TIR ABS CR 1 /MM 2 Travel Reverse Toggle To change count direction: Press button, then press the /MM button. Note: When arrow is pointed down, the display counts down with inward spindle movement for CR and ABS. When the arrow is pointed up, display counts up with inward spindle movement. For most applications this is the normal setting. TIR ABS CR 2 1 /MM 7

8 OPERATG STRUCTIONS Change Units To change the display units, press the /MM button. Default unit of measure is set at the factory for English or metric scales. TIR ABS CR /MM Hold Mode Allows you to hold the value on the display according to the specified mode. Press to toggle hold mode on and off. MAX Holds and displays the highest reading attained. M Holds and displays the lowest reading attained. FRZ Holds and displays the reading displayed when is engaged. To select type of (MAX, M, FRZ): Press until desired feature is flashing, then release. FRZ M MAX TIR ABS CR /MM 8 Note: Pressing ON/CLR button resets indicator to spindle position except in FRZ; resets to zero

9 OPERATG STRUCTIONS Tolerance On/Off Press to toggle tolerance mode on and off. If no tolerances are programmed into the gage, then tol is displayed to indicate an invalid tolerance setting and the HIGH and/or LOW icons flash on and off. When the tolerance settings are incorrect (high, low, or both) the corresponding icon or icons will flash. LOW HIGH ON TIR ABS CR /MM Tolerance Settings Continuously press the button to activate the tolerance menu (LOW, HIGH, ON) and view the low and high tolerance settings. If no preset tolerance number is set into the gage then zero will be displayed. When viewing low or high, that icon will flash. LOW HIGH ON TIR ABS CR /MM 9

10 OPERATG STRUCTIONS Set High Tolerance Number To change to high tolerance settings: Press button ( icon should appear on the display). Press the (Change) button. High icon will be flashing. SET LOW HIGH ON Use the secondary function buttons, Change and Move to set your tolerance setting. After you have set your high tolerance setting, press Apply to store numbers to memory. TIR ABS CR 1 /MM M A D E I N U S A 2 Set Low Tolerance Number To change to low tolerance settings: Press button ( icon should appear on the display). Press the (Change) button. Low icon will be flashing. SET Use the secondary function buttons, Change and Move to set your tolerance setting. After you have set your low tolerance setting, press Apply to store numbers to memory. Note: once high and low tolerances are set, the numeric readings will flash when your readings are out of tolerance. The LOW or HIGH icon will flash indicating if the reading is under or over the tolerance. 10 APPLY LOW HIGH ON TIR ABS CR 1 2 /MM TRVL MOVE CHANGE M A D E I N U S A

11 OPERATG STRUCTIONS Set Absolute Number Press and hold the OFF/MODE button. When the icon on LCD appears above the ABS lettering, release the OFF/MODE button. If no preset number is stored in indicator ABS will show on display. To change to absolute number (preset number), press button; icon should appear on the display. Press the (Change) button. TIR ABS CR 2 3 /MM 1 Use the secondary function buttons, Change and Move, to set your absolute number. Press Move until the +/- or digit to be set is blinking. SET Press the Change button to reverse the +/- sign or change the value of the blinking digit. Repeat until the desired number is entered. Press Apply to store absolute number to memory. TIR ABS CR /MM 11

12 OPERATG STRUCTIONS Lock Toggle When the LOCK is on, all of the setting modes are disabled, and all 2nd and 3rd functions are disabled except the lock/unlock sequence. Press the button ( icon should appear on the display). Press ON/CLR. Press. A key symbol will appear on the display when features are locked. TIR ABS CR 1 3 /MM APPLY 2 TRVL MOVE CHANGE Lock Combination Press the button ( icon should appear on the display), then press ON/CLR. Continuously press until 000 appears on the display. Use the CHANGE and MOVE button to set your lock combination. After you have set your 3 digit lock combination press APPLY. A key symbol will appear on the display and your 3 digit combination is stored in memory. WARNG: To change functions after the indicator has been locked with a combination, the correct combination must be applied. TIR ABS CR 1 /MM APPLY 2 TRVL MOVE CHANGE 3 Please contact the factory if the Lock Combination is lost. 12

13 OPERATG STRUCTIONS Reset to Factory Defaults This will set all features and functions back to the factory default settings. Press the button ( icon should appear on the display), followed by ON/CLR, then press /MM. Note: Factory defaults cannot be reset if the LOCK feature is on. 3 /MM TIR ABS CR 1 APPLY 2 TRVL MOVE CHANGE Verify Data I/O Type To view the Data I/O Type Output, press the button. The icon will appear on the display. Press ON/CLR. Press. Format information is displayed on the LCD. USB, SER, MTI, or BIPASS will appear on the LCD. To exit: Repeat button sequence. /MM TIR ABS CR APPLY 2 TRVL MOVE CHANGE

14 OPERATG STRUCTIONS Set Gage Resolution For the change resolution feature: Press, press ON/CLR, then press. After that, each press of the CHANGE Button () steps through the available resolution options:.001,.0005,.0001 or * *Note: Only resolutions coarser than indicator resolution-as-purchased are available. Analog graduations are set to match gage resolution. Press the APPLY button to store the resolution setting. Display returns to measuring mode at desired resolution, but does not change displayed value. SET TIR ABS CR 3 1 /MM 2 Display Setup Mode To change the display configuration, press the button, followed by the ON/CLR button. Then press the OFF/MODE button to enter the display configuration setting mode. The whole display flashes. Press CHANGE to cycle through the display options and choose APPLY to save the current display configuration. There are five display options. For example, the analog display can be turned off or the numbers can be turned off. 14 SET TIR ABS CR 1 /MM 2 3

15 OPERATG STRUCTIONS TIR Mode Total Indicator Runout (TIR) mode ignores travel direction, instead measuring the difference between peak and valley (MAX and M) values. To enter TIR Mode, continuously press the OFF/MODE button until the diamond icon appears above the TIR function. In TIR mode, the Freeze (FRZ) is the only hold function available. To view the Peak (MAX) Value or the Valley (M) Value, use the button. Press button down until the M or MAX is displayed. The difference between the M and MAX Values equals the TIR Value. 15

16 CUSTOM APPLICATIONS Custom LCDs and graphics can be provided for almost any application. We can help you design a gage for your exacting requirements. Keypads and features can be customized to meet most needs. For example, a gage can be programmed for T.I.R. only, or a gage can be programmed so only selected features are available. With our programmable software and flexible microchip, the possibilities are limited only by your imagination. Custom hardware is available to fit your specifications. For example, a gage can be made without a return spring or a custom spring. Special length stems, threaded stems, backs, and contact points, are also available. Digital Indicators are available in the following travels and resolutions: Range/Travel Resolution (operator changeable).250".0001"/.002mm;.00005"/.001mm.600".0005"/.01mm;.0001"/.002mm;.00005"/.001mm 1.0".0005"/.01mm;.0001"/.002mm;.00005"/.001mm 2.0".001"/.02mm;.0005"/.01mm;.0001"/.002mm 4.0".001"/.02mm;.0005"/.01mm;.0001"/.002mm 16 Part No. K