PXF Information. PXF Troubleshooting. Using show Commands APPENDIX
|
|
|
- Junior McCarthy
- 5 years ago
- Views:
Transcription
1 APPENDIX B Cisco Parallel express Forwarding (PXF) is used to accelerate forwarding performance on the Cisco 7304 router. PXF is available on the NSE-100 and NSE-150 only; the NPE-G100 does not support PXF. This appendix provides some basic information about using PXF. For more detailed information about PXF on the Cisco 7304 router, including which features are supported in PXF, restrictions, and configuration examples, see the for Cisco 7304 Routers document. The PXF processors are turned on by default. If they are ever disabled, you must enable them to take advantage of IP packet switching and feature acceleration. Note Before enabling the PXF processors, you must have IP routing and IP CEF switching turned on. To manually disable or enable the PXF processors, use the global commands: Hostname (config)# [no] ip pxf The following features are supported by the PXF processors and are enabled using standard IOS procedures: CEF Cisco Express Forwarding NetFlow Turbo ACL Turbo access control list See the Related Documentation section on page xvi to find documents about enabling these features. PXF Troubleshooting For PXF troubleshooting information, see the Cisco 7304 Troubleshooting module, the PXF Feature Support section at Using show Commands Use the global show version or show c7300 commands to obtain information about the hardware and software installed on your router. Examples of each follow. B-1
2 Using show Commands Appendix B Using the show version Command Use the show version command to display the configuration of the system hardware and the software version. B-2
3 Appendix B Using show Commands The following example of the show version command identifies an NSE-100 installed in a Cisco 7304 router: Router# show version Cisco Internetwork Operating System Software IOS (tm) 7300 Software (C7300-JS-M), Version 12.1(9)RELEASED, CISCO N Copyright (c) by cisco Systems, Inc. Compiled Fri 20-Apr-01 01:53 by biff Image text-base: 0x , data-base: 0x40BF2000 ROM: System Bootstrap, Version 12.1(9) [biff], RELEASED WStar_TOP uptime is 15 hours, 20 minutes System returned to ROM by power-on System restarted at 23:49:08 UTC Thu Apr System image file is "disk0:c7300-js-mz daily_build_ " cisco 7300 (NSE100) processor (revision A) with K/16384K bytes of memory. Processor board ID R7000 CPU at 350Mhz, Implementation 39, Rev 3.2, 256KB L2, 1024KB L3 Cache 4 slot midplane, Version Last reset from power-on X.25 software, Version PXF processor tmc0 is running. PXF processor tmc1 is running. 1 FastEthernet/IEEE interface(s) 2 Gigabit Ethernet/IEEE interface(s) 10 Packet over SONET network interface(s) 509K bytes of non-volatile configuration memory K bytes of ATA compact flash disk at bootdisk (Sector size 512 bytes) K bytes of ATA compact flash disk at disk 0 (Sector size 512 bytes). Configuration register is 0x100 Using the show c7300 Command Use the show c7300 subcommands to obtain information about the router. show c7300 info Show system information show pxf or show c7300 pxf Show PXF information (This command was modified to show pxf for the Cisco 7304 router. The Cisco IOS releases prior to 12.2(14)SZ that support the Cisco 7304 still require that show c7300 pxf be entered to gather PXF interface information.) show c7300 Show slots information Router> show c7300 info Network IO Interrupt Throttling: throttle count=0, timer count=0 active=0, configured=1 netint usec=3999, netint mask usec=200 C7300 Midplane EEPROM: Hardware Revision : 2.0 Chassis MAC Address : MAC Address block size : 256 B-3
4 Using show Commands Appendix B Number of Slots : 4 Chassis Serial Number : SCA053200L9 PCB Serial Number : SAA Part Number : Board Revision : A0 Fab Version : 01 RMA Test History : 00 RMA Number : RMA History : 00 Deviation Number : 0-0 Product Number : Top Assy. Part Number : Manufacturing Test Data : Field Diagnostics Data : Calibration Data : Minimum: 0 dbmv, Maximum: 0 dbmv Calibration values : EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF A C x10: C2 8B x20: 4C 39 C1 8B x30: C x40: CB x50: x60: C C x70: C x80: 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF C7300 NSE Mainboard EEPROM: Hardware Revision : 2.3 PCB Serial Number : CAB0532JYYX Part Number : Board Revision : A0 Fab Version : 02 RMA Test History : 00 RMA Number : RMA History : 00 Deviation Number : 0-0 Product Number : 7300-NSE-100 Top Assy. Part Number : Manufacturing Test Data : Field Diagnostics Data : Calibration Data : Minimum: 0 dbmv, Maximum: 0 dbmv Calibration values : EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF B C1 8B x10: 32 4A E x20: CB x30: D 4E D x40: EA 02 C x50: C C x60: C7 34 F6 44 F6 44 F6 44 F6 0x70: C D D x80: 00 D AC D D3 0x90: F3 DB FF FF FF 0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF B-4
5 Appendix B Using show Commands 0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF C7300 NSE Daughterboard EEPROM: Hardware Revision : 2.1 PCB Serial Number : CAB0531JYA6 Part Number : Board Revision : A0 Fab Version : 03 RMA Test History : 00 RMA Number : RMA History : 00 Deviation Number : 0-0 Product Number : 7300-NSE-100 Top Assy. Part Number : Manufacturing Test Data : Field Diagnostics Data : Calibration Data : Minimum: 0 dbmv, Maximum: 0 dbmv Calibration values : EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF C C1 8B x10: 31 4A x20: CB x30: D 4E D x40: EA 02 C x50: C C x60: C7 34 F6 44 F6 44 F6 44 F6 0x70: C D C D 00 0x80: x90: F8 BC FF FF FF 0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ROMMON Last Error Info: count: 19, reason: reset pc: 0x402765E8, error address: 0x Stack Trace: B-5
6 Using show Commands Appendix B Using the show c7300 pxf accounting or show pxf accounting Command The following is an example of the show c7300 pxf accounting or show pxf accounting command with sample output: Router> show c7300 pxf accounting PXF Utilization: 0 % PXF Packet Counters: Ingress from GE : 18 Egress to GE : 34 Ingress from LCs: 329 Egress to LCs: 8 Ingress from RP : 42 Egress to RP : 347 B-6
Configuring the OC3 POS Line Card
CHAPTER 4 To continue your OC3 POS line card installation, you must configure the OC-3 interfaces. This chapter contains the following sections: Using the EXEC Command Interpreter, page 4-1 Configuring
Configuration Register Information
APPENDIXA The following information is found in this appendix: Configuration Bit Meanings, page A-1 Displaying the Configuration Register While Running Cisco IOS, page A-5 Displaying the Configuration
Configuring the OC12 POS Line Card
CHAPTER 4 To continue your OC12 POS line card installation, you must configure the OC-12 interface. This chapter contains the following sections: Using the EXEC Command Interpreter, page 4-1 Configuring
Basic Troubleshooting Tasks and Startup Issues
CHAPTER 1 This chapter describes the basic procedures that users should perform before undertaking a detailed troubleshooting analysis of the Cisco 10000 series router or logging a case with the Cisco
Cisco 7206 Series Router-PBX Interoperability: Lucent Definity G3r PBX and VXC-2TE1+ Port Adapter Card with E1 ISDN PRI Signaling
Cisco 7206 Series Router-PBX Interoperability: Lucent Definity G3r PBX and VXC-2TE1+ Port Adapter Card with E1 ISDN PRI This document describes the interoperability and configuration of a Cisco 7200 series
Useful Switch Information
Useful Switch Information More detailed information is available at http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/index.htm Summary of Commands 1 The enable command 1 The show mac-address-table
NPE-300 and NPE-400 Overview
CHAPTER 3 This chapter describes the network processing engine (NPE) models NPE-300 and NPE-400 and contains the following sections: Supported Platforms, page 3-1 Software Requirements, page 3-1 NPE-300
Password Recovery Procedure for the Catalyst 5500 Supervi
Password Recovery Procedure for the Catalyst 5500 Supervi Table of Contents Password Recovery Procedure...1 for the Catalyst 5500 Supervisor RSFC...1 Introduction...1 Before You Begin...1 Conventions...1
o Password Recovery Procedure for the Catalyst 6000 MSFC
o Password Recovery Procedure for the Catalyst 6000 MSFC Table of Contents Password Recovery Procedure...1 for the Catalyst 6000 MSFCI/MSFCII...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1
Lucent/Avaya Definity G3si V9 PBX with CallManager using the Cisco 3640-T1 PRI as an MGCP Gateway
Application te Lucent/Avaya Definity G3si V9 PBX with CallManager using the Cisco 3640-T1 PRI as an MGCP Gateway This application note discusses the integration of the Lucent/Avaya Definity G3si V9 PBX
Troubleshooting the Cisco UBR-RFSW-ADV
This chapter describes the troubleshooting procedures for the Cisco ubr Advanced RF Switch (UBR-RFSW-ADV). Basic Troubleshooting, page 1 Troubleshooting Individual Hardware Components, page 9 Basic Troubleshooting
Using the Setup Script
APPENDIX A Using the Setup Script The information herein applies to the Cisco AS5350, Cisco AS5400, and Cisco AS5400HPX universal gateways that the latter requires use of Cisco IOS release 122(2)XB or
ubr7200 Series Router Architecture
ubr7200 Series Router Architecture Document ID: 16044 Contents Introduction Before You Begin Conventions Prerequisites Components Used Hardware Architecture Chassis Overview Network Processing Engines
Cisco 7200 Series Router Architecture
Cisco 7200 Series Router Architecture Document ID: 5810 Contents Introduction Prerequisites Requirements Components Used Conventions Hardware Architecture Chassis Overview Network Processing Engines Network
Maintaining the Cisco 7202 Router
CHAPTER 6 This chapter describes basic maintenance procedures for the Cisco 7202. The procedures are presented in the following sections: Viewing Your System Configuration, page 6-1 Removing and Replacing
ord Recovery Procedure for the Cisco Catalyst 8510 Multiserv
ord Recovery Procedure for the Cisco Catalyst 8510 Multiserv Table of Contents Password Recovery Procedure for the Cisco Catalyst 8510 Multiservice Switch Router...1 Introduction...1 Before You Begin...1
Configuring Interfaces
CHAPTER 9 This chapter describes how to configure interfaces on the Catalyst 6500 series switches. This chapter consists of these sections: Understanding Interface Configuration, page 9-2 Using the Interface,
Multiprocessor WAN Application Module
1 CHAPTER This chapter describes the (MWAM) and includes the following sections: Product Overview, page 1-2 MWAM Ordering Information, page 1-2 Hardware Description, page 1-3 Functional Description, page
Upgrade ROMMON initialized program load complete, entry point: 0x8000f000, size: 0xcb40
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Copyright (c) 2006 by cisco Systems, Inc. System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1) Copyright (c) 2008 by cisco Systems,
Table of Contents. Cisco The no service password recovery Command for Secure ROMMON Configuration Example
Table of Contents The no service password recovery Command for Secure ROMMON Configuration Example...1 Introduction...1 Prerequisites...1 Requirements...1 Hardware and Software Requirements...1 Components
Table of Contents. Cisco Xmodem Console Download Procedure Using ROMmon
Table of Contents Xmodem Console Download Procedure Using ROMmon...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Overview...2 Usage...2 Examples...3 Xmodem
PCMCIA Filesystem Compatibility Matrix and Filesystem Information
PCMCIA Filesystem Compatibility Matrix and Filesystem Information Document ID: 6145 Contents Introduction Before You Begin Conventions Prerequisites Components Used PCMCIA Filesystem Compatibility Matrix
Installing and Upgrading Software
This chapter describes how to update software on the Cisco ASR 920 Series Router. Upgrading Field Programmable Hardware Devices, page 1 File Systems on the Cisco ASR 920 Series Router, page 1 Restrictions,
Rebooting and Reloading - Configuring Image Loading Characteristics
Rebooting and Reloading - Configuring Image Loading Characteristics The basic processes completed by a Cisco device (such as a router) when it reboots can be specifically configured to improve function
Catalyst 6500/6000 MSFC Boot from the Supervisor Engine PC Card Configuration Example
Catalyst 6500/6000 MSFC Boot from the Supervisor Engine PC Card Configuration Example Document ID: 65079 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information
Table of Contents. Cisco Password Recovery Procedure for the Cisco 2000, 2500, 3000, 4000, AccessPro, 7000 (RP), AGS, IGS, STS
ry Procedure for the Cisco 2000, 2500, 3000, 4000, AccessPro, , IGS, STS Table of Contents Password Recovery Procedure for the Cisco 2000, 2500, 3000, 4000, AccessPro, 7000 (RP), AGS, IGS, STS 10x...1
Cisco Series Internet Router Architecture: Maintenance Bus, Power Supplies and Blowers, and Alarm Cards
Cisco 12000 Series Internet Router Architecture: Maintenance Bus, Power Supplies and Blowers, and Alarm Cards Document ID: 47244 Contents Introduction Prerequisites Requirements Components Used Conventions
Lab Managing IOS Images with TFTP Instructor Version 2500
Lab 5.2.5 Managing IOS Images with TFTP Instructor Version 2500 Objective Backup a copy of a router IOS from flash to a TFTP server. Reload the backup IOS software image from a TFTP server into flash on
Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments
Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments April 14, 2008 This document describes how to configure the Cisco access router and the Cisco Wide Area Application
How to Upgrade Software Images on Catalyst Switch Layer 3 Modules
How to Upgrade Software Images on Catalyst Switch Layer 3 Modules Document ID: 20685 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Before You Begin
Xmodem Console Download Procedure Using ROMmon
Xmodem Console Download Procedure Using ROMmon Contents Introduction Prerequisites Requirements Components Used Conventions Overview Usage Examples Xmodem Procedure for Downloading a Cisco IOS Software
No Service Password-Recovery
No Service Password-Recovery Last Updated: January 18, 2012 The No Service Password-Recovery feature is a security enhancement that prevents anyone with console access from accessing the router configuration
co Password Recovery Procedure for the Cisco 1700 Series R
co Password Recovery Procedure for the Cisco 1700 Series R Table of Contents Password Recovery Procedure for the Cisco 1700 Series Routers...1 Introduction...1 Before You Begin...2 Conventions...2 Prerequisites...2
Configuring the PA-FE-TX or PA-FE-FX
CHAPTER 4 To continue your PA-FE-TX or PA-FE-FX port adapter installation, you must configure the Fast Ethernet interface. The instructions that follow apply to all supported platforms. Minor differences
Bringing Up Cisco IOS XR Software on the Router
CHAPTER 2 This chapter provides instructions for bringing up the Cisco IOS XR software on a standalone router for the first time. This section applies to standalone routers that are delivered with Cisco
SAMI Cisco IOS PPC Commands
APPENDIXC The following commands, listed in alphabetical order, are introduced or modified for the Cisco SAMI Cisco IOS PPCs and are supported at the SAMI Cisco IOS PPC console: clear sami ixp statistics
If this is your first time configuring the switch, you will notice that the Switch IOS is almost identical to Router IOS.
Spanning Tree Lab Objective Create a basic switch configuration and verify it. Determine which switch is selected as the root switch with the factory default settings. Force the other switch to be selected
The specifications for the Cisco 7304 router are listed in Table A-1.
APPENDIX A This appendix provides system and component specifications for the Cisco 7304 router. The following topics are found in this appendix: System, page A-1 Processor and Memory and Configurations,
Lab 5.2.6b Managing IOS Images with ROMmon and Xmodem Instructor Version 2500
Lab 5.2.6b Managing IOS Images with ROMmon and Xmodem Instructor Version 2500 Objective Recover a Cisco router stuck in ROM monitor (ROMmon) mode. Learn how to avoid having to use Xmodem to restore an
Cisco CMTS Router ROM Monitor Commands
alias, page 2 boot, page 4 break, page 8 confreg, page 10 cont, page 14 context, page 16 cpu_card_type, page 18 dev, page 19 dir, page 21 dis, page 23 frame, page 25 help, page 27 history, page 29 meminfo,
FIRST BOOT OF THE ROUTER & STORING ITS CONFIGURATION
Volume Issue pp 008-003 March 202 www. ijsret.org ISSN 2278-0882 FIRST BOOT OF THE ROUTER & STORING ITS CONFIGURATION Gyan Prakash Pal Faculty of Electronics & Communication Engineering Department, Shanti
Configure TCP Intercept on Cisco IOS?/IOS- XE Routers
Configure TCP Intercept on Cisco IOS?/IOS- XE Routers Contents Introduction Prerequisites Requirements Components Used Problem For ISR G1 Routers For ISR G2 Routers For ISR G3 Routers For ASR1k Routers
Configuring the SS7 Port Adapter
CHAPTER 4 To continue your SS7 Port Adapter installation, you must configure the card type as either T1 or E1 and then configure the interfaces. This chapter contains the following sections: Using the
How to Upgrade from ROMmon Using the Boot Image
How to Upgrade from ROMmon Using the Boot Image Document ID: 6301 Contents Introduction Prerequisites Requirements Components Used Conventions What Is the Boot Image? (Rx boot) Loading the Boot Image Related
This document describes how to perform datapath packet tracing for Cisco IOS -XE software via the Packet Trace feature.
Contents Introduction Prerequisites Requirements Components Used Reference Topology Packet Tracing in Use Quick Start Guide Enable Platform Conditional Debugs Enable Packet Trace Egress Condition Limitation
System Startup and Basic Configuration
CHAPTER 4 System Startup and Basic Configuration The system startup process and a procedure for performing a basic configuration of your Cisco 12016, Cisco 12416, or Cisco 12816 router is presented in
CS 537: Introduction to Operating Systems Fall 2015: Midterm Exam #1
CS 537: Introduction to Operating Systems Fall 2015: Midterm Exam #1 This exam is closed book, closed notes. All cell phones must be turned off. No calculators may be used. You have two hours to complete
II+/II+TS/II+10GE/III/IV/V/V 10GE
Password Recovery Procedure for the Catalyst 4500/4000 Supervisor Engine II+/II+TS/II+10GE/III/IV/V/V 10GE Module and Catalyst 4900 Switches that Run Cisco IOS Software Document ID: 21229 Contents Introduction
Using Flexible NetFlow Flow Sampling
This document contains information about and instructions for configuring sampling to reduce the CPU overhead of analyzing traffic with Flexible NetFlow. NetFlow is a Cisco technology that provides statistics
Using Flexible NetFlow Flow Sampling
This document contains information about and instructions for configuring sampling to reduce the CPU overhead of analyzing traffic with Flexible NetFlow. NetFlow is a Cisco technology that provides statistics
Tech Note: Configuring Q.SIG PRI trunk between Cisco Call Manager and Avaya S8700/G650 with Cisco Unity Voice Mail integration
Tech Note: Configuring Q.SIG PRI trunk between Cisco Call Manager and Avaya S8700/G650 with Cisco Unity Voice Mail integration The objective of this document is to provide Cisco s customers and business
The objective of this lab is to become familiar with Cisco switches as well as the Spanning Tree Protocol.
CIS 83 LAB 4 - Spanning Tree Protocol Rich Simms October 3, 2006 Objective The objective of this lab is to become familiar with Cisco switches as well as the Spanning Tree Protocol. Scenario This lab was
Onboard Failure Logging
Onboard Failure Logging First Published: August 10, 2007 Last Updated: August 10, 2007 The Onboard Failure Logging (OBFL) feature collects data such as operating temperatures, hardware uptime, interrupts,
Network Processing Engine and Network Services Engine Installation and Configuration
Network Processing Engine and Network Services Engine Installation and Configuration Product Number: NPE-100=, NPE-150=, NPE-175=, NPE-200=, NPE-225=, NPE-300=, NPE-400=, NSE-1=, NPE-G1=, UBR7200-NPE-G1=,
assword Recovery Procedure for the Catalyst 4000 Supervisor
assword Recovery Procedure for the Catalyst 4000 Supervisor Table of Contents Password Recovery Procedure for the Catalyst 4000 Supervisor III/IV Module...1 Introduction...1 Before You Begin...1 Conventions...1
1. Slow port emulation with R_RDY delay of us (1.5 seconds) 2. Port-monitor - slow port emulation with R_RDY delay of us (1.
Contents Introduction Topology Restrictions in Cisco NX-OS Software Releases Cisco NX-OS Software Release 5.2(8) Cisco NX-OS Software Releases Earlier than 5.2(6) Test 1: Slow Port Emulation with R_RDY
Intel(R) Core(TM) i3 CPU M 2.40GHz
CPU-Z Binaries CPU-Z version 1.62.0 Processors Number of processors 1 Number of threads 4 APICs Processor 0 -- Core 0 -- Thread 0 0 -- Thread 1 1 -- Core 2 -- Thread 0 4 -- Thread 1 5 Timers ACPI timer
Cisco 2621 Gateway-PBX Interoperability: Alcatel 4400 with E1 PRI NET5 Signaling
Cisco 2621 Gateway-PBX Interoperability: Alcatel 4400 with E1 PRI NET5 Signaling This document describes the interoperability and configuration of a Cisco 2621 Gateway with an Alcatel 4400 PBX using E1
Password Recovery Procedure for the Cisco 1700 and 1800 Series Routers
Password Recovery Procedure for the Cisco 1700 and 1800 Series Routers Document ID: 22187 Introduction Prerequisites Requirements Components Used Related Products Conventions Step by Step Procedure Example
Appendix A: Data Registers
Appendix A: Data Registers Data registers can be dedicated to a specific purpose, optionally dedicated or continuously available for user data. They can be designated as Read Only or Read & Write. Data
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with E1 PRI NET5 Signaling
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with E1 PRI NET5 Signaling This document describes the interoperability and configuration of a Cisco 2621 voice gateway with a Lucent/Avaya
Troubleshoot IOS Hypervisor and System Image Recovery for CGR 1000
Troubleshoot IOS Hypervisor and System Image Recovery for CGR 1000 Contents Introduction Prerequisites Requirements Components Used Steps to Recover Hypervisor and System Image Download Hypervisor Images
Configure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration
Configure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration Document ID: 63790 Contents Introduction Prerequisites Requirements Components Used Conventions Test
Catalyst 6000/6500 Series Switches with Redundant Supervisor Engines Software Image Upgrade Configuration Example
Catalyst 6000/6500 Series Switches with Redundant Supervisor Engines Software Image Upgrade Configuration Example Document ID: 71585 Contents Introduction Prerequisites Requirements Components Used Related
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with T1 PRI Signaling
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with T1 PRI Signaling This document describes the interoperability and configuration of a Cisco 2621 voice gateway with a Lucent/Avaya
Configuring Interfaces
CHAPTER 6 The chapter applies to the ML-Series (ML100T-2, ML100X-8, ML1000-2 cards. This chapter describes basic interface configuration for the ML-Series card to help you get your ML-Series card up and
Version 4.1. Configuring Network Devices
Version 4.1 Configuring Network Devices Objectives Configure a router with an initial configuration. Use Cisco SDM to configure a Cisco ISR with LAN connectivity, Internet connectivity and NAT. Configure
Configuring the Cisco ubr-mc88v Cable Interface Line Card
Configuring the Cisco ubr-mc88v Cable Interface Line Card First Published: February 15, 2010 The Cisco ubr-mc88v cable interface line card is a DOCSIS 3.0 line card designed specifically for Cisco ubr7246vxr
Lab - Exploring Router Physical Characteristics
Topology Objectives Part 1: Examine Router External Characteristics Part 2: Examine Router Internal Characteristics Using Show Commands Background / Scenario In this lab, you will examine the outside of
Password Recovery Procedure for the Cisco 801, 802, 803, 804, 805, 811, and 813 Series Routers
Password Recovery Procedure for the Cisco 801, 802, 803, 804, 805, 811, and 813 Series Routers Document ID: 12732 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions
Onboard Failure Logging Commands
This module describes the Cisco IOS XR software commands used to configure onboard failure logging (OBFL) for system monitoring on the router. OBFL gathers boot, environmental, and critical hardware failure
How to Verify Cisco Express Forwarding Switching
How to Verify Cisco Express Forwarding Switching Document ID: 47205 Contents Introduction Prerequisites Requirements Components Used Conventions What Is Cisco IOS Switching? Verification Steps Understand
Configuring Basic File Transfer Services
Using basic file transfer services, you can configure a router as a Trivial File Transfer Protocol (TFTP) or Reverse Address Resolution Protocol (RARP) server, configure the router to forward extended
Configuring the SS7 Q.703 High Speed Port Adapter
CHAPTER 4 Configuring the SS7 Q.703 High Speed Port Adapter This chapter contains the following sections: Using the EXEC Command Interpreter, page 4-1 Configuring the Interfaces, page 4-2 Checking the
Products & Services Hardware Troubleshooting for AS5200 and AS5300 Series Routers. Please rate this document. Excellent. Good. Average. Fair.
Products & Services Hardware Troubleshooting for AS5200 and AS5300 Series Routers Document ID: 17881 Interactive: This document offers customized analysis of your Cisco device. TAC Notice: What's Changing
Cable Modem Basic Install with Cisco Network Registrar
Cable Modem Basic Install with Cisco Network Registrar Document ID: 12547 Contents Introduction Prerequisites Requirements Components Used Conventions Lab Topology Assumptions Network Diagram Cisco Network
See the following sections for configuration tasks for this feature: Set Up Siemens Hicom PBX Configuration Cisco 3640 Gateway Configuration
Cisco 3640 Series Gateway-PBX Interoperability: Siemens Hicom 300E PBX with T1 CAS Signaling This document describes the interoperability and configuration of a Cisco 3640 Series voice gateway with a Siemens
SMART CONNECTION TO SMART HOME VENTO
SMART CONNECTION TO SMART HOME VENTO Expert A50- W VENTO Expert Duo A30- W EN OPERATION MANUAL VENTO Expert www.blaubergventilatoren.de CONTENTS Purpose...2 Network parameters...3 Control commands...3
Configuring NetFlow and NetFlow Data Export
This module contains information about and instructions for configuring NetFlow to capture and export network traffic data. NetFlow capture and export are performed independently on each internetworking
Troubleshooting: Deactivating Applications in a Virtual Services Container, page 7
Collecting Information, page 1 : Installing Applications in a Virtual Services Container, page 3 : Activating Applications in a Virtual Services Container, page 5 : Uninstalling Applications in a Virtual
Router Field Diagnostics
CHAPTER 6 This chapter describes the diagnostic commands you can use to troubleshoot line cards, Route Processor cards (PRP and GRP), Switch Fabric Cards (SFC), and Clock Scheduler Cards (CSC) installed
BASIC CONFIGURATION CISCO SWITCH
BASIC CONFIGURATION CISCO SWITCH switch#show running-config ( prikaz trenutne konfiguracije ) switch#show startup-config ( prikaz startne konfiguracije ) switch#configure terminal ( ulaz u global config
Configuring Data Export for Flexible NetFlow with Flow Exporters
Configuring Data Export for Flexible NetFlow with Flow Exporters Last Updated: September 4, 2012 This document contains information about and instructions for configuring flow exporters to export Flexible
Scenarios A P P E N D I X
A P P E N D I X B Scenarios This appendix contains a set of lab scenarios, each of which contains some type of problem statement that you need to solve. Some scenarios ask specific questions. Others ask
TPMC815 ARCNET PMC. User Manual. The Embedded I/O Company. Version 2.0. Issue 1.2 November 2002 D
The Embedded I/O Company TPMC815 ARCNET PMC Version 2.0 User Manual Issue 1.2 November 2002 D76815804 TEWS TECHNOLOGIES GmbH Am Bahnhof 7 25469 Halstenbek / Germany Phone: +49-(0)4101-4058-0 Fax: +49-(0)4101-4058-19
First-Time Configuration
CHAPTER 3 This chapter contains information with which you should be familiar before you begin to configure your router for the first time, including information about understanding boot images, interface
Venstar Thermostat Adapter
Developer Venstar Thermostat Adapter v001 Developer Venstar Thermostat Adapter Version 001 May 23, 2013 Revision History Rev Date Comments 001 05/23/13 Initial Release Page 1 of 13 Table of Contents 1
AVT-84x Auto Block Transmit (ABX)
ADVANCED VEHICLE TECHNOLOGIES, Inc. AV AVT-84x Auto Block Transmit (ABX) Inc. 20 November 2009 The so-called Auto Block Transmit function (noted as ABX ) became available in firmware version 3.0 (and later).
Chapter 6: Network Layer
Chapter 6: Network Layer Introduction to Networks Intro to Networks v5 Network Layer Intro to Networks v5 2 The Network Layer End to End Transport processes Addressing end devices Encapsulation of Packets
Maintaining the MGX RPM-PR
APPENDIX A This appendix describes maintenance procedures you might need to perform as your internetworking needs change. It contains the following sections: Reading Front Panel LEDs Recovering a Lost
Release notes for Flash Recovery Tool Version 10.0(2)
Release notes for Flash Recovery Tool Version 10.0(2) Problem Description After several months or years in continuous operation, underlying boot flash devices on NEXUS 7000 SUP2/2E supervisor boards may
Configuring the Cisco ASR 1000 Series Modular Ethernet Line Card
Configuring the Cisco ASR 1000 Series Modular Ethernet Line Card This chapter provides information about configuring the Cisco ASR 1000 Series Modular Ethernet Line Card on the Cisco ASR 1000 Series Routers.
Managing the Router Hardware
This chapter describes the command-line interface (CLI) techniques and commands used to manage and configure the hardware components of a router running the Cisco IOS XR software. For complete descriptions
DEFAULT IP ADDRESS
REAL TIME AUTOMATION 2825 N. Mayfair Rd. Suite 111 Wauwatosa, WI 53222 (414) 453-5100 www.rtaautomation.com EtherNet/IP - DeviceNet Master Gateway MODBUS TCP - DeviceNet Master Gateway Copyright 2007 Real
Configuring the SM-1-STM1
4 CHAPTER To continue your SM-1-STM1 service module installation, you must configure the STM-1 interface. This chapter contains the following sections: Configuring the Interface, page 4-1 Checking the
Configuring Data Export for Flexible NetFlow with Flow Exporters
Configuring Data Export for Flexible NetFlow with Flow Exporters Last Updated: November 29, 2012 This document contains information about and instructions for configuring flow exporters to export Flexible
SRF02 Ultrasonic range finder Technical Specification
SRF02 Ultrasonic range finder Technical Specification I2C Mode For Serial mode click here I2C Communication To use the SRF02 in I2C mode, make sure nothing is connected to the mode pin, it must be left
Redundancy Commands CHAPTER
CHAPTER 7 CPU switch module redundancy provides protection against CPU switch module failure. Use the following commands to configure and monitor CPU switch module redundancy operations. 7-1 auto-sync
The cache is 4-way set associative, with 4-byte blocks, and 16 total lines
Sample Problem 1 Assume the following memory setup: Virtual addresses are 20 bits wide Physical addresses are 15 bits wide The page size if 1KB (2 10 bytes) The TLB is 2-way set associative, with 8 total
Cisco IOS Commands for the Catalyst 6500 Series Switches with the Supervisor Engine 32 PISA
2 CHAPTER Cisco IOS Commands for the Catalyst 6500 Series Switches with the Supervisor Engine 32 PISA This chapter contains an alphabetical listing of Cisco IOS commands that are unique to the Catalyst