SC20MPC: 2 Mega Pixels Serial JPEG Camera User Manual. Introduction

Transcription

1 2 Mega Pixels Serial JPEG Camera SC20MPC User Manual, Rev. F (August 2018) For latest user manual, please visit: Introduction The SC20MPC Camera is a highly integrated serial JPEG camera module which can be attached to any host system that requires a JPEG compressed still camera for embedded imaging applications. The module uses a 1/4 CMOS color image sensor along with a JPEG compression chip that provides a low cost and low powered camera system. The module has an on-board serial interface (TTL/RS232/RS485) that is suitable for a direct connection to any host microcontroller UART or a PC system COM port. The SC20MPC camera is capable of outputting JPEG format images only. User commands are sent using a simple serial protocol that can instruct the camera to send high resolution (160x120 to 1600x1200) JPEG images for storage or viewing. The SC20MPC camera module comes in a compact form factor with a built in lens and PH 2.0 4Pin socket connector that provides easy access to both power and serial data. There are 8 lenses available for this camera from Spinel. A 60 degree (Standard), a 150 degree, 120 degree, 90 degree, a 45 degree, a 30 degree, a 15 degree and a 8 degree. The SC20MPC ships with the 60 degree lens installed for standard order, other lenses can be installed in house before delivery for custom orders. There is a locking screw on the side of the lens mount, which is used to lock the focus in place once set, to prevent it from inadvertently being changed. Features Small size, low cost and low powered camera module for embedded imaging applications. 5V DC Power Supply (standard), optional 12V or wide voltage 9-36V per request. 1

2 On-board EEPROM provides a command-based interface to external host via serial link. High baud rate up to bps, which can transfer JPEG images or VGA with 0.75~6 fps. On board 2 mega pixel color sensor and JPEG CODEC for different resolutions. Image size: 1600x1200/1280x960/1024x768/800x600/VGA/QVQAF/160x120. Dimensions: 32mm x 32mm x 28mm (with lens). Weight ~0.3oz (9g). VC0706 protocol compatible. Pin Configuration and Dimensions From left to right: Pin 1 Pin 2 Pin 2 Pin 4 RXD TXD GND VCC Electrical Specification VDD = 3.3V+10%, TA = 0 to 25 Parameter Min Typ Max Unit Operating Voltage V 2

3 Operation Current ma Operating Ambient Temperature OPTICAL CHARACTERISTICS Item Image Sensor Pixel Size Shutter Type SNR max Dynamic Range Maximum Frame Rate White Balance Exposure Lens viewing angle (6 options) Focal Length IR-cut filter IR-cut filter switch (ICR) Sensitivity Parameter 1/4 CMOS, OV um*5.6um Electronic Rolling Shutter 45DB 60DB Automatic Automatic, self-regulating 60 degree (default), 8, 15, 30, 45, 90, 120 and 150 degree optional 3.6mm(default), 1.7mm, 2.8mm, 6mm, 8mm, 12mm, 16mm, 24mm optional 650nm(default for true color), 850nm and 940nm optional Default not available, can customized automatic IR-cut filter switch with spinel supplied IR illuminator 1250mV/Lux-sec Command Protocol (HEX format data) 1. RESET The host can reset the camera by issuing this command: D 0A 49 6E E 64 0D 0A 2. GET IMAGE The host issues this command to capture an image from camera READ IMAGE DATA LENGTH XH XM XL XH XM XL is the image date length, XH---high byte, XL---low byte. 4. READ IMAGE DATE Send: C 00 0A 00 MM MM MM 00 KK KK KK 00 0A (interval) FF D8 FF D9 (interval) MM MM MM is the starting address, it must be the multiple of 8, for instance

4 SC20MPC: 2 Mega Pixels Serial JPEG Camera User Manual 00 KK KK KK is the image data length, lower bytes follow the higher bytes. 5. STOP CAPTURE SET JPEG RESOLUTION (IMAGE SIZE) (Default: 1600 x 1200) The JPEG preview mode can support following image sizes. It is different from normal preview mode. The default image size is 1600x1200, it will return back to default after power off or reset. A different default image size can be preset prior to order. Resolution Commands Return 160x x x x D 1024x C 1280x B 1600x SET IMAGE COMPRESSION RATIO (Default: 08) The host can set the default Baud rates using this command XX XX can usually range from 05 to 27, 27 is the most compressed, and 05 is the least compressed. 8. SET BAUD RATE (Default: bps) The host can set the temporary Baud rates using this command, the baud rate will return to default baud rate after re-power up, the default baud rate can be preset in house by Spinel only and is not allowed to be changed by users. Use the table below as a guide. Baud Commands Return Rate AE A C D E E

5 9. SET DEFAULT BAUD RATE The host can set the default Baud rate using this command, the baud rate will be valid after power off. Use the table below as a guide. Baud Rate Commands Return AE A C D E SET IR-CUT FILTER If the SC20MPC camera is customized with IR-cut filter, the host can set the filter by issuing the following commands for day and night mode, no commands needed if the camera also comes with Spinel supplied infrared LED plate that can control the IR-cut filter switcher automatically, otherwise commands are needed. Mode Commands Return Day mode AA AA Night mode AA AA GET IMAGE PROCESS 1. Get image command 2. Read image data length command 3. Read image data command 4. Stop capture 12. Program flow chart 12.1 Initialize After power up, the camera will output: Ctrl infr exist User-defined sensor 625 Init end ( D 0A 49 6E E 64 0D 0A) 5

6 12.2 Get JPEG image TEST THE CAMERA WITH PC 1. Test with Spinel PC test tool The PC Test Tool can be downloaded from our website: the application only supports window XP/7/8 as of now. The camera needs to have RS232 output or TTL to RS232 converter to connect to the serial port of the PC, or use a USB to TTL converter if the camera comes in TTL output and the computer doesn t have a serial pot, please make sure select the default baud rate to ensure proper running. The following image illustrates the interface of the evaluation software. 6

7 2. TEST AND TROUBLESHOOTING For any technical issue or error, please use SSCOM serial debug tool to test the camera and figure out the issue, the SSCOM serial debug tool and instruction can be downloaded from our websites: or For questions regarding this user manual, please to or Or Call +1(800) Thank you. 7