Quick Reference Guide

Transcription

1 English for Asia*, Africa, Oceania and atin America Quick eference Guide *Except for hina and Korea Accessories The following accessories are supplied with this product. PUSH emote control Batteries () (AAA, 0, UM-) AM loop antenna Indoor FM antenna AUX input cover PAO microphone Preparing the remote control Take off the battery compartment cover. Insert the two supplied AAA batteries into the battery case, following the polarity markings. Snap the battery compartment cover back into place. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. within 6 m Items necessary for connection Speakers Ex. Ex. Ex. Ex. Front speaker enter speaker Surround speaker, surround back speaker, and presence speaker Active subwoofer Use speakers with an impedance of at least 6 Ω. Ω speakers can also be used as the front speakers. For more information on speaker impedance, refer to page. If you are using a T monitor, we recommend that you use magnetically shielded speakers. Prepare at least two front speakers. The priority of the other speakers is as follows: Two surround speakers One center speaker One (or two) surround back speaker (s)/presence speakers External components able ables for connecting external components (may differ depending on the components you are connecting) Playback device such as (Blu-ray Disc)/ players Speaker cables (a quantity to match the number of speakers you are connecting) Audio pin cable (for subwoofer) - -

2 onnect and install as follows the fi rst time you use this unit. See the following explanations for the connections for each number. This unit / player (recorder) Front speaker Front speaker Subwoofer Surround speaker enter speaker 6. Surround back speaker Surround speaker 7. Surround back speaker 7. Surround back speaker 7. onnect when using with 7.-channel speaker layout. Place the surround back speakers (/) 0 cm or more away from each other. onnect the speakers onnect a 6. onnect when using with 6.-channel speaker layout. Place the surround back speaker behind the listening position. onnect playback device such as / players and recorders Set the VOTAGE SEETO and connect the A power cable (Asia and General models) onnect the A power cable (Other models) 5 Set up the speaker parameters automatically (PAO) - -

3 I H onnect the speakers Front speaker Surround speaker Surround back speaker onnect when using with 7.-channel speaker layout. 6. onnect when using with 6.-channel speaker layout. aution: 5 SPEAKES FONT ENTE SUOUND SUOUND BAK/ BI-AMP ZONE MOTE SINGE +V 0.A MAX. E OUT ENTE SINGE ND SU.BAK SUBWOOFE AUDIO ZONE FONT SUOUND SU.BAK OUT OUT E OUT I H ENTE SUBWOOFE emove the A power cable of this unit from the power outlet before connecting the speakers. Generally speaker cables consist of two parallel insulated cables. One of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the + (positive, red) terminal on this unit and the speakers, and the other cable into the - (minus, black) terminal. Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, HEK SP WIES! will appear on the front panel display when this unit is switched on. This unit is configured for 8 Ω speakers at the factory setting. When connecting 6 Ω speakers, configure the speaker impedance setting of this unit to 6 Ω. When this unit is configured for 6 Ω speakers, Ω speakers can also be used as the front speakers. For more information on setting the speaker impedance, refer to hanging speaker impedance in the Owner s Manual. enter speaker Subwoofer When connecting the presence speakers, refer to Presence speaker connection in the Owner s Manual. This unit can connect speakers that support Bi-amp connection for front speakers. efer to Bi-amp connection in the Owner s Manual for the details. onnecting speakers FONT emove approximately 0 mm of insulation from the ends of the speaker cables, and twist the bare wires of the cables together fi rmly so that they will not cause short circuits. oosen the speaker terminals. Insert the bare wire of the speaker cable into the gap on the side of the terminal. Tighten the terminal. onnecting the subwoofer onnect the subwoofer input jack to the SUBWOOFE or jack on this unit with an audio pin cable. Set the subwoofer volume as follows. Volume: Set to approximately half volume (or slightly less than half). rossover frequency (if available): Set to maximum. OSSOVE/ HIGH UT MIN MAX MIN MAX Subwoofer examples - -

4 O OUT (D) ( ) A onnect a If your has multiple inputs, connect with the following priority (A to ). DOK A SEETABE A (/) H A When using an compatible. ANTENNA FM GND AM EMOTE IN GND 75 MONITO OUT OUT V +V 0.A MAX TIGGE OUT B When using a component video input-compatible. OAXIA OAXIA (D) ( ) OUT FONT SUOUND SU I H I 5 6 AUDIO AUDIO MUTI H I V When using a compatible with video input only. Video input to this unit is output to a using output jacks of the same kind. When connecting to an compatible Video signal such as component video and video received by this unit is converted to and output to the. Just select input on the to view video from any external source connected to this unit. ou can change the resolution and aspect ratio when converting to to suit your requirements. Through onverted Input Output input omponent video input Video input When connecting to a non- compatible onnect to the using the same type of connection that you used to connect to the playback device, and change the inputs on your to match that of the playback device you are using for playback. If the playback device and are equipped with different types of analog video jacks, this unit will convert the video signal to component video signal, or vice-versa, according to the type of video input jacks used by the. For more information on video signal conversion, refer to onnecting a monitor in the Owner s Manual. Through onverted Input Output omponent video input Video input istening to audio To playback audio on this unit, connect the audio output to this unit. onnect the following input jacks, matching the audio output jacks on your. When viewing your, select the appropriate input source on this unit. When using an compatible that supports Audio eturn hannel functions and / or ontrol functions (e.g., Panasonic VIEA ink), you can enjoy the sound on this unit as follows: Audio output DOK OAXIA GND OAXIA H 5 O When using a that supports the Audio eturn hannel function and ontrol function The audio / video output from the unit to the and audio output from the to the unit are possible using a single cable. The input source is switched automatically to match operations carried out on the, and that makes sound control easier to use. For the connections and settings, refer to Using the ontrol function in the Owner s Manual. Audio output from Optical digital output oaxial digital output Analog output Audio eturn hannel (Described in the right column) Input jack on this unit or or One of 5, 6, AUDIO, AUDIO, and -AUX OUT or OUT onnecting to allows you to playback audio just by pressing the under SENE key. When using a that supports ontrol functions When ontrol functions are enabled on the unit, input source can be switched automatically to match operations carried out on the. For the connections and settings, refer to Using the ontrol function in the Owner s Manual. - -

5 EXTA SP ZONE/ESENE O EXTA SP ZONE/ESENE onnect playback device such as / players and recorders If your playback device has multiple audio/video outputs, connect with the following priority (A to D) to enjoy a higher quality sounds and images. A When playback device is capable of output DOK OUT (/) B When playback device is capable of component video output (with optical digital audio output) O A SEETABE A ANTENNA FM GND AM EMOTE IN GND 75 OUT When playback device is capable of component video output (with coaxial digital audio output) OAXIA O OAXIA OAXIA (D) V ( ) OUT +V 0.A MAX. MONITO OUT TIGGE OUT FONT SUOUND SU.BAK SU I H 5 6 AUDIO AUDIO MUTI H D When playback device is capable of video output (with analog audio output) only AUDIO V When playback, select the corresponding input source to which the jack is connected. At the default settings, input sources and sound programs are preset on the SENE keys. When a playback device is connected to, pressing / under SENE key selects the input. When a playback device is connected to, pressing D under SENE selects the input. The input source and sound program preset on the SENE key can be changed. For more information on the SENE function, refer to hanging input settings with a single key (SENE function) in the Owner s Manual. If necessary, you can connect components that cannot be connected using the above methods, such as devices that output video from component video output jacks and audio from analog output jacks. efer to onnecting external components in the Owner s Manual for details. Set the VOTAGE SEETO and connect the A power cable (Asia and General models) onnect the A power cable (Other models) (Asia and General models only) Select the switch position according to your local voltage using a straight slot screwdriver. (General model) Voltages are A 0/0/0/0-0 V, 50/60 Hz. (Asia model) Voltages are A 0/0-0 V, 50/60 Hz. VOTAGE SEETO VOTAGE SEETO AKES VOTAGE SEETO AKES To the power outlet A power cable aution The VOTAGE SEETO on the rear panel of this unit must be set for your local voltage BEFOE plugging the power cable into the A wall outlet. Improper setting of the VOTAGE SEETO may cause damage to this unit and create a potential fi re hazard

6 5 Set up the speaker parameters automatically (PAO) When all connections are complete, adjust the confi guration, sizes, and volume balance of the speakers to provide an optimal sound field. This unit is equipped with a amaha Parametric oom Acoustic Optimizer (PAO) function that adjusts the speaker balance automatically with a simple procedure. When using PAO, a test tone will be output from the speakers for approximately minutes to measure acoustics. Be aware of the following when using PAO. The test tone is output at high volume. efrain from using this function at night when it may be a nuisance to others. Take care that the test tone does not frighten small children. PAO operations can be viewed on the front panel display or screen. display is used here to explain operation. heck the following before using PAO. This unit The headphones are removed. This unit is connected to the correctly. The power is turned on. The video input to which the video output from this unit has been selected. Subwoofer The power is turned on. Volume is set to approximately half, and the cross-over frequency (if present) is set to maximum. OSSOVE/ HIGH UT MIN MAX MIN MAX Subwoofer examples Place the supplied PAO microphone at ear height in your listening position. PAO microphone When positioning the microphone, we recommend that you use equipment that allows you to adjust the height (such as a tripod) as a microphone stand. When using a tripod, use the tripod screws to fi x the microphone in place. Measuring, for multiple listening positions, is also available. For more information, refer to Setting up the speaker parameters automatically (PAO) in the Owner s Manual. Press EEIVE A on the remote control to switch this unit on. onnect the PAO microphone to the PAO MI jack on the front panel. MAIN ZONE Mic On. View ON SEEN appears on the front panel display, and then the display at right appears on the screen. ZONE ZONE ONTO INFO MEMO PHONES PAO MI TONE ONTO SIENT INEMA PAO microphone This completes preparation. To achieve more accurate results, take note of the following when measuring acoustics. It takes approximately minutes to accurately measure acoustics. Keep the room as quiet as possible while acoustics are measured. Wait in a corner of the room, or leave it entirely, while acoustics are measured to avoid creating an obstruction between the speakers and the PAO microphone. ontinues to the next page - 6 -

7 5 Use the cursor B/ to select the Measure and press ENTE to start measurement. When Multi Position is set to es (default), the measurement of multiple positions will follow. efer to Setting up the speaker parameters automatically (PAO) for details on Multi Position in the Owner s Manual. The following display appears if measurement fi nishes without any problems. esult Displays the results of automatic acoustics measurement and sets the equalizer (parametric equalizer) to provide a unified sound field. For details, refer to eviewing and reloading the automatic setup parameters in the Owner s Manual. Save/Exit Applies the result to the speaker setup and fi nishes the automatic measurement. MAIN ZONE ODE SET SOUE EEIVE AUDIO 5 V-AUX 5 6 MUTI DOK OUT TUNE FM AM ESET TUNING INFO MEMO ENHANE SU. DEODE MOVIE MUSI SEEP PAT STAIGHT PUE DIET SENE D ADIO ON SEEN OPTION EEIVE A ON SEEN Note ETUN ENTE DISPA ENTE, ursor If a problem occurs, an error message or report is displayed either during or after acoustic measurement. efer to When an error message is displayed during measurement, or When a warning message is displayed after measurement in the Owner s Manual to resolve the problem and measure acoustics with PAO again. TOP MENU E POP-UP MENU MUTE 6 7 Use the cursor to select Save/Exit and press ENTE. Use the cursor D/E to select SE and press ENTE. When the display at left appears, the PAO setup is complete ENT VO H MUTE 8 Press ENTE. PAO is automatically terminated. Disconnect the PAO microphone. PHONES PAO MI TONE ONTO SIENT INEMA ou can use the following functions with this unit. For details on the operations, refer to the Owner s Manual on the supplied D-OM. Adjustment for various parameters to match your listening environment - Sound quality control with a parametric equalizer <PEQ Select> - Easy listening at low volumes <Adaptive D> - Adjusting volume between input sources <Volume Trim> FM/AM tuner - Manual preset tuning - (Asia and General models only) hanging FM/AM frequency steps External device connection and playback - onnections and playback from / players (recorders), audio, and other devices - Playback from an ipod/iphone - Playback from a Bluetooth device etc

8 MAIN ZONE ZONE PHONES SIENT INEMA ZONE ONTO PAO MI INFO MEMO ESET FM AM TUNING TONE ONTO SENE OGAM D ADIO STAIGHT AUX IN AUDIO PUE DIET Operation guide A B D G F A Switches this unit between on and standby mode This unit switches between on and standby mode every time you press this key. A B hoose an input source to listen to The name of the selected input source appears on the front panel display. VO. S SB SW S SB MAIN ZONE ODE SET SOUE EEIVE Switches between input settings ou can switch input sources and sound field programs with a single key. SENE Input Sound field program ompressed Music Enhancer mode OUT / Drama Off OUT + STAIGHT On OUT + D STAIGHT Off OUT + ADIO TUNE STAIGHT On OUT + - Pressing and holding this key allows you to store input sources/sound field programs. - Press this key when this unit is in standby mode to switch on the unit. F AUDIO 5 V-AUX 5 6 MUTI DOK OUT TUNE FM AM ESET TUNING INFO MEMO ENHANE SU. DEODE MOVIE MUSI SEEP PAT STAIGHT PUE DIET B D Adjusts the volume level The current volume level is displayed on the front panel display. ON SEEN SENE D ADIO OPTION VO. Volume -8.5dB S SB SW S SB ENTE D E Mutes the sound The indicator blinks while the sound is muted. ETUN TOP MENU DISPA POP-UP MENU MUTE E F Select sound field programs and sound decoders Front panel OGAM emote control MOVIE MUSI SU. DEODE Description Selects sound field programs optimized for viewing movies, dramas, and sports. Selects sound field programs optimized for appreciating music. Selects surround decoders such as Dolby Pro ogic II. E ENT VO H MUTE STAIGHT STAIGHT Switches to Straight decoding mode for stereo/multi-channel playback without using a sound field program. PUE DIET PUE DIET Switches to Pure Direct mode for faithful reproduction of audio. - When playing back compression artifacts, press ENHANE to turn on the ompressed Music Enhancer mode. G Adjusting high/low-frequency sound (Tone control) Press TONE ONTO to select Treble or Bass. TONE Treble +0.5dB VO. S SB SW S SB otate OGAM selector to adjust the output level in those frequency ranges. - ou can set the tone control for speakers and headphones separately. onnect the headphones when adjusting the headphone tone control. - If you set an extreme tone balance, sounds may not match those from other channels amaha orporation 55A0/QEN